Get documents about "Sony - CDX-MP80 - Installation Guide · English 0.64 Mb
Shared by: manualsmania
Categories
Tags
-
Stats
- views:
- 149
- posted:
- 9/10/2008
- language:
- Newar / Nepal Bhasa
- pages:
- 4
Document Sample
3-251-178-31 (1)
3 A
AUDIO OUT
FRONT
SUB OUT (MONO)
FM/MW/LW
Compact Disc
Player AUDIO OUT
REAR
Installation/Connections
B BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
Source selector*
*
XA-C30
BUS CONTROL IN
* not supplied
CDX-MP80
© 2003 Sony Corporation Printed in Korea
Cautions Connection example (3)
1 124 142.5
•This unit is designed for negative earth 12 V Notes (3-A)
• Be sure to connect the earth cord before
DC operation only.
•Do not get the wires under a screw, or caught connecting the amplifier.
• If you connect an optional power amplifier and do
in moving parts (e.g. seat railing).
not use the built-in amplifier, the beep sound will
19 18.5 •Before making connections, turn the car
be deactivated.
ignition off to avoid short circuits.
60 170
•Connect the yellow and red power input leads Tip (3-B- )
Unit: mm only after all other leads have been connected. For connecting two or more CD/MD changers, the
•Run all earth wires to a common earth source selector XA-C30 (optional) is necessary.
point.
Dimensions include unit size, front panel and disc tray open, etc. •Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow) Connection diagram (4)
•When connecting this unit in combination with
1 To a metal surface of the car
other stereo components, the connected car First connect the black earth lead, then connect
2 circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
the orange/white striped, yellow, and red power
input leads.
2 To the power aerial control lead or power
1 2 3 4 connect the unit directly to the battery. supply lead of aerial booster amplifier
Notes
TO
P • It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/LW aerial
×4 Before installation (1) in the rear/side glass, see “Notes on the control
•Do not install the unit where its operation and power supply leads.”
5 6 7 interferes with driving. (1) 3 To AMP REMOTE IN of an optional power
Example: amplifier
— Opening and closing of the front panel or This connection is only for amplifiers. Connecting
disc tray interfere with operation of the any other system may damage the unit.
gear shift. 4 To the interface cable of a car telephone
×2 — With the front panel open, operation of 5 To a car’s illumination signal
hazard lamps, switches etc., is impaired. Be sure to connect the black earth lead to a
metal surface of the car first.
6 To the +12 V power terminal which is energized
in the accessory position of the ignition key
Equipment used in illustrations (not supplied) switch
Parts Iist (2) Notes
• If there is no accessory position, connect to the
Front speaker Power amplifier The numbers in the list are keyed to those in the +12 V power (battery) terminal which is
energised at all times.
instructions.
Be sure to connect the black earth lead to a
metal surface of the car first.
Caution • When your car has a built-in FM/MW/LW aerial
Rear speaker CD/MD changer
Handle the bracket 1 carefully to avoid injuring in the rear/side glass, see “Notes on the control
your fingers. and power supply leads.”
7 To the +12 V power terminal which is energised
at all times
TO
P
Be sure to connect the black earth lead to a
Active subwoofer Rotary commander RM-X4S metal surface of the car first.
4
3 *1 Supplied with XA-C30
Source selector
(not supplied)
*1 Supplied with the CD/MD changer
XA-C30
SUB OUT (MONO)
AUDIO OUT
*1 BUS AUDIO IN FRONT REMOTE IN
*1 RCA pin cord (not
*5 supplied)
*2 Auxiliary optional
*3 BUS
AUDIO IN
REAR FRONT
AUDIO OUT
equipment such as
portable DVD player DVP-
FX1 (not supplied)
*2 AUDIO OUT REAR BUS
AUX IN
CONTROL IN *3 supplied with the auxialiry
(AUDIO)*4 Fuse (10 A) equipment
from car aerial
*4 Be sure to match the color-
Blue/white striped 7 coded code for audio to
AMP REM the appropriate jacks from
3 Max. supply current 0.3 A Black
the unit.
White
1 *5 Insert with the cord
upwards
Left Blue
ANT REM
White/black striped
Max. supply current 0.1 A
2
Grey Light blue
ATT
Right 4
Grey/black striped
Orange/white striped
ILLUMINATION
Green 5
Left
Red
Green/black striped
6
Purple Yellow
Right
7
Purple/black striped
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V •
DC when you turn on the tuner or when you
3
activate the AF (Alternative Frequency), TA (Traffic
• 3
Announcement) function. •
• •
• When your car has built-in FM/MW/LW aerial in •
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input •
lead (red) to the power terminal of the existing 3 •
aerial booster. For details, consult your dealer. •
• A power aerial without relay box cannot be used
with this unit. •
•
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
4 •
•
1 •
Notes on speaker connection
• Before connecting the speakers, turn the unit off. •
• Use speakers with an impedance of 4 to 8 ohms, • 2
and with adequate power handling capacities to •
avoid its damage. • •
• Do not connect the speaker terminals to the car •
chassis, or connect the terminals of the right •
speakers with those of the left speaker. •
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
1 3
• Do not attempt to connect the speakers in parallel. • 1 •
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker 4
terminals may damage the unit. 5
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares 6
a common negative (–) lead for the right and left
speakers. •
• Do not connect the unit’s speaker cords to each
other. 2
•
7
1
TO
P
5 A B
(OFF)
A
B
(RELEASE)
6 * 1
182
mm
53 m
TO m
P
1
with the TOP marking up
2 3 4
Dashboard
Fire wall
1 TO
P
4
4
5
6
Bend these claws outward 2
for a tight fit, if necessary. 5
5 4
3
7 A TOYOTA B NISSAN
4 4
max. size max. size
5 × 8 mm 5 × 8 mm
to dashboard/centre console to dashboard/centre console
Bracket
4 4
max. size Bracket max. size
5 × 8 mm 5 × 8 mm
Bracket Bracket
Existing parts supplied with your car Existing parts supplied with your car
Precautions Mounting the unit in a Japanese
• Choose the installation location carefully so car (7) • 7
that the unit will not interfere with normal
You may not be able to install this unit in some
driving operations. •
makes of Japanese cars. In such a case, consult
• Avoid installing the unit in areas subject to
your Sony dealer.
dust, dirt, excessive vibration, or high •
temperatures, such as in direct sunlight or near Note 4
heater ducts. To prevent malfunction, install only with the
• Use only the supplied mounting hardware for supplied screws 4.
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 30°.
Warning when installing in a car 5
without ACC (accessory) (OFF)
position on the ignition key
How to detach and attach the switch 5
front panel (5) (OFF)
After tuning off the ignition, be sure to (RELEASE)
Before installing the unit, detach the front press and hold (OFF) on the unit until the
panel. clock display disppears. 5
Otherwise, the display does not turn off and this A B
5-A To detach causes battery drain.
Before detaching the front panel, be sure to
press (OFF). Press (RELEASE) to open up the
front panel and pull it off towards you.
5-B To attach
RESET button 6
Attach part A of the front panel to part B of the When the installation and connections are
unit as illustrated and push the left side into completed, be sure to press the RESET button
position until it clicks. with a ballpoint pen, etc., after removing the 6 *
front panel.
Mounting example (6)
Installation in the dashboard
When installing this unit, be sure to close the
front panel of the unit. (6-*)
Do not hold the unit by its front panel or disc
tray when installing as this can damage the unit,
or cause malfunction.
Other docs by manualsmania
Samsung - SGH-E330 - SGH-E330 User Manual (ver.1.0) - BULGARIAN - PDF - PDF
Views: 81 | Downloads: 0
