CID _ SIA Event Codes

Document Sample
CID _ SIA Event Codes Powered By Docstoc
					CID   Event Type
100   Medical
101   Personal Emergency
102   Fail to report in
110   Fire
111   Smoke
112   Combustion
113   Water Flow
114   Heat
115   Pull Station
116   Duct
117   Flame
118   Near Alarm
120   Panic
121   Duress
122   Silent
123   Audible
124   Duress Access granted
125   Duress Egress granted
126   Hold-up suspicion print
130   Burglary
131   Perimeter
132   Interior
133   24 Hour (Safe)
134   Entry/Exit
135   Day/Night
136   Outdoor
137   Tamper
138   Near alarm
139   Intrusion Verifier
140   General Alarm
141   Polling loop open
142   Polling loop short
143   Expansion module failure
144   Sensor tamper
145   Expansion module tamper
146   Silent Burglary
147   Sensor Supervision Failure
150   24 Hour Non-Burglary
151   Gas detected
152   Refrigeration
153   Loss of heat
154   Water Leakage
155   Foil Break
156   Day Trouble
157   Low bottled gas level
158   High temp
159   Low temp
161   Loss of air flow
162   Carbon Monoxide detected
163   Tank level
200   Fire Supervisory
201   Low water pressure
202   Low CO2
203   Gate valve sensor
204   Low water level
205   Pump activated
206   Pump failure
300   System Trouble
301   AC Loss
302   Low system battery
303   RAM Checksum bad
304   ROM checksum bad
305   System reset
306   Panel programming changed
307   Self-test failure
308   System shutdown
309   Battery test failure
310   Ground fault
311   Battery Missing/Dead
312   Power Supply Overcurrent
313   Engineer Reset
314   Radio battery charger failure
320   Sounder/Relay
321   Bell 1
322   Bell 2
323   Alarm relay
324   Trouble relay
325   Reversing relay
326   Notification Appliance Ckt. # 3
327   Notification Appliance Ckt. #4
330   System Peripheral trouble
331   Polling loop open
332   Polling loop short
333   Expansion module failure
334   Repeater failure
335   Local printer out of paper
336   Local printer failure
337   Exp. Module Power Loss
338   Exp. Module Low Battery
339   Exp. Module Power On / Reset
341   Exp. Module Tamper
342   Exp. Module AC Loss
343   Exp. Module self-test fail
344   RF Receiver Jam Detect
350   Communication Path Failure
351   Telco 1 fault
352   Telco 2 fault
353   Long Range Radio xmitter fault
354   Failure to communicate event
355   Loss of Radio ECP supervision
356   Loss of central polling
357   Long Range Radio VSWR problem
358   Periodic Comm Test Fail /Restore
370   Protection loop
371   Protection loop open
372   Protection loop short
373   Fire trouble
374   Exit error alarm (zone)
375   Panic zone trouble
376   Hold-up zone trouble
377   Swinger Trouble
378   Cross-zone Trouble
380   Sensor trouble
381   Loss of supervision - RF
382   Loss of supervision - RPM
383   Sensor tamper
384   RF low battery
385   Smoke detector Hi sensitivity
386   Smoke detector Low sensitivity
387   Intrusion detector Hi sensitivity
388   Intrusion detector Low sensitivity
389   Sensor self-test failure
391   Sensor Watch trouble
392   Drift Compensation Error
393   Maintenance Alert
394   CO Detector needs replacement
400   Open/Close
401   O/C by user
402   Group O/C
403   Automatic O/C
404   Late to O/C (Note: use 453 or 454 instead)
405   Deferred O/C (Obsolete- do not use )
406   Cancel
407   Remote arm/disarm
408   Quick arm
409   Keyswitch O/C
411   Callback request made
412   Successful download/access
413   Unsuccessful access
414   System shutdown command received
415   Dialer shutdown command received
416   Successful Upload
421   Access denied
422   Access report by user
423   Forced Access
424   Egress Denied
425   Egress Granted
426   Access Door propped open
427   Access point Door Status Monitor trouble
428   Access point Request To Exit trouble
429   Access program mode entry
430   Access program mode exit
431   Access threat level change
432   Access relay/trigger fail
433   Access RTE shunt
434   Access DSM shunt
435   Second Person Access
436   Irregular Access
441   Armed STAY
442   Keyswitch Armed STAY
443   Armed with System Trouble Override
450   Exception O/C
451   Early O/C
452   Late O/C
453   Failed to Open
454   Failed to Close
455   Auto-arm Failed
456   Partial Arm
457   Exit Error (user)
458   User on Premises
459   Recent Close
461   Wrong Code Entry
462   Legal Code Entry
463   Re-arm after Alarm
464   Auto-arm Time Extended
465   Panic Alarm Reset
466   Service On/Off Premises
501   Access reader disable
520   Sounder/Relay Disable
521   Bell 1 disable
522   Bell 2 disable
523   Alarm relay disable
524   Trouble relay disable
525   Reversing relay disable
526   Notification Appliance Ckt. # 3 disable
527   Notification Appliance Ckt. # 4 disable
531   Module Added
532   Module Removed
551   Dialer disabled
552   Radio transmitter disabled
553   Remote Upload/Download disabled
570   Zone/Sensor bypass
571   Fire bypass
572   24 Hour zone bypass
573   Burg. Bypass
574   Group bypass
575   Swinger bypass
576   Access zone shunt
577   Access point bypass
578   Vault Bypass
579   Vent Zone Bypass
601   Manual trigger test report
602   Periodic test report
603   Periodic RF transmission
604   Fire test
605   Status report to follow
606   Listen-in to follow
607   Walk test mode
608   Periodic test - System Trouble Present
609   Video Xmitter active
611   Point tested OK
612   Point not tested
613   Intrusion Zone Walk Tested
614   Fire Zone Walk Tested
615   Panic Zone Walk Tested
616   Service Request
621   Event Log reset
622   Event Log 50% full
623   Event Log 90% full
624   Event Log overflow
625   Time/Date reset
626   Time/Date inaccurate
627   Program mode entry
628   Program mode exit
629   32 Hour Event log marker
630   Schedule change
631   Exception schedule change
632   Access schedule change
641   Senior Watch Trouble
642   Latch-key Supervision
651   Reserved for Ademco Use
652   Reserved for Ademco Use
653   Reserved for Ademco Use
654   System Inactivity
655   User Code X modified by Installer
703   Auxiliary #3
704   Installer Test
750   User Assigned CID Message
751   User Assigned CID Message
752   User Assigned CID Message
753   User Assigned CID Message
754   User Assigned CID Message
755   User Assigned CID Message
756   User Assigned CID Message
757   User Assigned CID Message
758   User Assigned CID Message
759   User Assigned CID Message
760   User Assigned CID Message
761   User Assigned CID Message
762   User Assigned CID Message
763   User Assigned CID Message
764   User Assigned CID Message
765   User Assigned CID Message
766   User Assigned CID Message
767   User Assigned CID Message
768   User Assigned CID Message
769   User Assigned CID Message
770   User Assigned CID Message
771   User Assigned CID Message
772   User Assigned CID Message
773   User Assigned CID Message
774   User Assigned CID Message
775   User Assigned CID Message
776   User Assigned CID Message
777   User Assigned CID Message
778   User Assigned CID Message
779   User Assigned CID Message
780   User Assigned CID Message
781   User Assigned CID Message
782   User Assigned CID Message
783   User Assigned CID Message
784   User Assigned CID Message
785   User Assigned CID Message
786   User Assigned CID Message
787   User Assigned CID Message
788   User Assigned CID Message
789   User Assigned CID Message
796   Unable to output signal (Derived Channel
798   STU Controller down (Derived Channel)
900   Download Abort
901   Download Start/End
902   Download Interrupted
910   Auto-close with Bypass
911   Bypass Closing
912   Fire Alarm Silence
913   Supervisory Point test Start/End
914   Hold-up test Start/End
915   Burg. Test Print Start/End
916   Supervisory Test Print Start/End
917   Burg. Diagnostics Start/End
918   Fire Diagnostics Start/End
919   Untyped diagnostics
920   Trouble Closing (closed with burg. Durin exit)
921   Access Denied Code Unknown
922   Supervisory Point Alarm
923   Supervisory Point Bypass
924   Supervisory Point Trouble
925   Hold-up Point Bypass
926   AC Failure for 4 hours
927   Output Trouble
928   User code for event
929   Log-off
954   Communication Failure
999   1 and 1/3 Day No Read Log
Event Description
A non-specific medical condition exists
Emergency Assistance request
A user has failed to activate a monitoring device
A non-specific fire alarm condition exists
An alarm has been triggered by a smoke detector
An alarm has been triggered by a combustion detector
An alarm has been triggered by a water flow detector
An alarm has been triggered by a heat detector
A pull station has been activated
An alarm has been triggered by a duct detector
An alarm has been triggered by a flame detector
A near-alarm condition has been detected on a fire sensor
A non-specific hold-up alarm exists
A duress code has been entered by a user
A silent hold-up alarm exists
An audible hold-up alarm exists
A duress code has been entered and granted at an entry door
A duress code has been entered and granted at an exit door
A user has activated a trigger to indicate a suspicious condition
A burglary zone has been violated while armed
A perimeter zone has been violated while armed
An interior zone has been violated while armed
A 24 hour burglary zone has been violated
An Entry/Exit zone has been violated while armed
An trouble by Day / alarm by Night zone has been violated while armed
An outdoor burglary zone has been violated while armed
A burglary zone has been tampered with while armed
A burg sensor has detected a condition which will cause it to go into alarm if the condition worsens
The specified zone has verified that an intrusion has occurred
The specified zone is in an alarm condition
An open circuit condition has been detected on a polling loop while the system was armed
A short circuit condition has been detected on a polling loop while the system was armed
A general failure condition has been detected on an expansion module while the system was armed
A sensor's tamper has been violated (case opened)
An expansion module's tamper has been violated (cabinet opened)
A burglary zone has been violated while armed with no audible notification produced
A sensor's supervisory circuit has reported a failure while the system was armed
A non-burglary zone has been faulted
The gas detector assigned to the specified zone has reported a fault condition
The refrigeration detector assigned to the specified zone has reported a fault condition
The temperature detector assigned to the specified zone has reported a fault condition
The water leak detector assigned to the specified zone has reported a fault condition
The specified zone which is assigned to foil used as glass break detection has reported a fault condition
The specified zone which monitors trouble by day has reported a fault condition while disarmed
The gas level detector assigned to the specified zone has reported a fault condition
The over-temperature detector assigned to the specified zone has reported a fault condition
The under-temperature detector assigned to the specified zone has reported a fault condition
The air flow detector assigned to the specified zone has reported a fault condition
The carbon monoxide detector assigned to the specified zone has reported a fault condition
The tank level detector assigned to the specified zone has reported a fault condition
The supervisory circuit of the specified fire zone has reported a fault condition
The water pressure sensor assigned to the specified zone has reported a fault condition
The CO2 pressure sensor assigned to the specified zone has reported a fault condition
The gate valve sensor in the fire sprinkler system assigned to the specified zone has reported a fault condition
The water level sensor assigned to the specified zone has reported a fault condition
The pump activity detector assigned to the specified zone has reported an active condition
A pump output monitor assigned to the specified zone has reported a fault condition
A general system trouble condition has been reported by the specified zone
AC power loss has been detected at a control or expansion module while the system was disarmed
A battery has failed a load test while the system was disarmed
A test of the system's memory has failed
A test of the system's executable memory has failed
The system has reset and restarted
The programmed configuration of the panel has changed
The system has failed a self-test
The system has been shut down and has stopped functioning
The system backup battery has failed a load test while the system was disarmed
The panel has detected a ground fault condition
The system has detected that the backup battery is either missing or completely discharged.
The system power supply has reported an excessive current draw condition
The specified service person has issued a system reset
The system's primary power supply has failed a supervision test. Radio devices indicate this when the backup battery chargin
A trouble condition exists in the system's sounder/relay circuit
A trouble condition exists in the primary bell circuit
A trouble condition exists in the secondary bell circuit
A trouble condition exists in the system's alarm relay circuit
A trouble condition exists in the system's trouble relay circuit
The specified TELCO reversing relay has reported a trouble condition
A trouble condition exists in the bell #3 circuit
A trouble condition exists in the bell #4 circuit
A system peripheral device has reported a trouble condition
An open circuit condition has been detected on a polling loop while the system was disarmed
A short circuit condition has been detected on a polling loop while the system was disarmed
A general failure condition has been detected on an expansion module while the system was disarmed
A repeater in the system has reported a failure condition while the system was disarmed
The printer attached to the panel has reported an Out Of Paper condition
The printer attached to the panel has reported a failure condition
An expansion module has detected a DC power loss
An expansion module has detected a low battery condition
An expansion module has reset
An expansion module has detected its tamper switch has been faulted
An expansion module has detected the loss of AC power
An expansion module has failed a self-test
An RF receiver has detected the presence of a jamming signal which prevents it from receiving normal signalsfrom the system
The system has experienced difficulties communicating with the central station
The system has detected a fault on the primary dial-up line
The system has detected a fault on the secondary dial-up line
A fault has been detected in the long range radio subsystem
The system was unable to communicate an event to the central station
The radio has not reported in its designated supervision interval
The radio has detected a loss in the polling signal from it's associated receiver
The Long Range Radio has reported a transmitter/antenna problem
A periodic Communication path test has failed
The specified protection loop has reported a trouble condition
The specified protection loop has reported an open-loop trouble condition
The specified protection loop has reported a shorted-loop trouble condition
A fire sensor has detected a trouble condition on the specified zone while the system was disarmed
An exit error condition has been reported for the specified alarm zone
The system has detected a trouble condition on the panic zone
The system has detected a trouble condition on the hold-up zone
A fault has occurred on a zone that has been shut down due to excessive alarms
The specified zone in a cross-zone configuration has faulted without a fault on its corresponding cross-zone ina specific time p
The specified sensor has reported a trouble condition
The specified zone has failed to report in during its designated supervision period
An Remote Polled Module assigned to the specified zone has failed supervision
The tamper switch on the specified sensor has been faulted
The specified battery powered RF zone has reported a low battery condition
A smoke detector's sensitivity level has drifted to the upper limit
A smoke detector's sensitivity level has drifted to the lower limit
An intrusion detector's sensitivity level has drifted to the upper limit
An intrusion detector's sensitivity level has drifted to the lower limit
The specified sensor has failed a self-test
A motion sensor has not been triggered within a pre-defined time interval
A smoke detector cannot automatically adjust its sensitivity
The specified zone requires maintenance
The specified Carbon Monoxide detector has reached end-of-life
The specified user has disarmed/armed the system
The specified user has disarmed/armed the system
A group of zones has been armed or disarmed
A partition has been automatically armed or disarmed
Late to Open or Close
Deferred Open or Close
The specified user has cancelled the previously reported alarm condition
The specified user has armed or disarmed the system from off-premises
The specified user has quick-armed the system
The specified user has armed or disarmed the system using a keyswitch
A remote site (central station) has requested the panel call it back
The configuration data of the system has been successfully downloaded
A number of failed attempts have been made to remotely access the system
A central station has sent a system shutdown command to the panel
A central station has sent a dialer shutdown command to the panel
The configuration data of the system has been successfully uploaded
The access control system has denied access to the specified user

The specified access control door has been forced open
The access control system has denied egress to the specified user
The access control system has granted egress for the specified user
The specified access control door has been held open
The specified Access Point's Door Status Monitor has reported a trouble condition to the panel
The specified Access Point's Request To Exit zone has reported a trouble condition to the panel
The access control system has been put into program mode
The access control system has exited program mode
The access control system's threat level has been changed
The specified access control output device has failed to operate properly
The specified Request To Exit zone has been shunted and will no longer report activity
The specified Door Status Monitor zone has been shunted and will no longer report activity
A second person has accessed an access point conforming to Two-Man-Rule requirements

The specified user has armed the system in STAY mode
The specified user has armed the system in STAY mode using a keyswitch
The specified user has armed the system while overriding a trouble condition
The system has been armed or disarmed outside of the configured time window
The system has been disarmed/armed by the specified user before the configured time window has started
The system has been disarmed/armed by the specified user after the configured time window has ended
The system has failed to have been disarmed during the designated time window
The system has failed to be armed during the designated time window
The system has failed to automatically arm itself at the designated time
The system has been only partially armed by the specified user
The specified user has made an error exiting the premises after arming the system
A user has disarmed the system after an alarm has occurred
The system had been armed within the last xx minutes




A user has successfully requested that the system delay automatically arming
The specified panic zone has been reset
A service person has entered or left the premises
The credential reader on the specified access point has been disabled
The specified sounder or relay has been disabled
The specified output for Bell 1 has been disabled
The specified output for Bell 2 has been disabled
The specified alarm relay has been disabled
The specified trouble relay has been disabled
The specified reversing relay has been disabled
The specified output for Bell 3 has been disabled
The specified output for Bell 4 has been disabled
The specified access control module has been added to the system
The specified access control module has been removed from the system
The specified dialer has been disabled
The specified radio transmitter has been disabled
Remote configuration has been enabled
The specified zone or sensor has been bypassed
The specified fire zone has been bypassed
The specified 24 hour zone has been bypassed
The specified burglary zone has been bypassed
A group of zones has been bypassed
The specified zone which has reported an excessive number of faults/restores in a short period of time has been bypassed
The specified zone in the access control system has been shunted and will no longer report activity
The specified access point in the access control system has been bypassed and will allow the door to open(unsecured)
The specified vault zone has been bypassed
The specified vent zone has been bypassed and will no longer report any activity
A test report has been triggered manually
A periodic test report has been triggered
A periodic RF path test report has been triggered
The specified user has initiated a test of the fire alarm zones

The system is about to activate a 2-way audio session
The specified user has placed the system into the walk-test mode for testing purposes
A periodic test has been triggered but the fire system has a trouble condition present
A video look-in session is about to begin
The specified point tested successfully
The specified point has not been tested
The specified intrusion zone has been successfully walk-tested
The specified fire zone has been successfully walk-tested
The specified panic zone has been successfully walk-tested
A request has been made for system servicing
The event log has been reset and all stored events have been discarded
The event log is 50% full
The event log is 90% full
The event log has overflowed and events have been lost
The time and date have been reset to a new value by the specified user
The system time and date is known to be in error
The system has been placed into program mode
The system has exited program mode
In the last 31.9 hours (1 and 1/3 days), nothing has been posted to the event log. There is nothing new toread. Does not send
The specified fire/burglary schedule has been changed
The time schedule for event reporting by exception has been changed
The specified access control schedule has been changed
A person has not activated a motion sensor in a specified period
A child has disarmed the system (after school)
System has not been operated for x days
The Installer has modified the specified User's code




The specified Downloader ID has aborted a download sequence in progress
Downloader has started or ended a download sequence to the panel
A download sequence has been interrupted
An auto-close sequence has been started and the specified zone has been bypassed

The fire alarm has been silenced
A fire supervisory device has been tested
The specified user has started or ended a hold-up test
The printed progress of a burglary test has been started or ended
The printed progress of a supervisory test has been started or ended
A burglary system diagnostic test has been started or ended
A fire system diagnostic test has been started or ended


Access has been denied because the system did not recognize the supplied access code as valid
The specified supervisory point has reported an alarm condition
The specified supervisory point has been bypassed
The specified supervisory point has reported a trouble condition
The specified hold-up point has been bypassed
There has been a loss of AC power for at least four hours
The specified output has reported a trouble condition
This message contains the ID of the user who triggered the previous event
The specified user has logged-off of the system
Comm fail to the primary (zone 951) or secondary (zone 952) 7810iR-ent in private LAN mode
In the last 31.9 hours (1 and 1/3 days), nothing has been posted to the event log. There is nothing new toread. Does not send
backup battery charging circuit has failed its supervision test
signalsfrom the system RF devices




-zone ina specific time period
e has been bypassed

 pen(unsecured)




w toread. Does not send to central station and only occurs in the Vista-20/SE and FA sister products.
w toread. Does not send to central station and only occurs in the Vista-20/SE and FA sister products.
Data Code   Short Description
   AA       Alarm – Panel Substitution
   AB       Abort
   AN       Analog Restoral
   AR       AC Restoral
   AS       Analog Service
   AT       AC Trouble
   BA       Burglary Alarm
   BB       Burglary Bypass
   BC       Burglary Cancel
   BD       Swinger Trouble
   BE       Swinger Trouble Restore
   BG       Unverified Event - Burglary
   BH       Burglary Alarm Restore
    BJ      Burglary Trouble Restore
   BM       Burglary Alarm - Cross Point
   BR       Burglary Restoral
   BS       Burglary Supervisory
   BT       Burglary Trouble
   BU       Burglary Unbypass
   BV       Burglary Verified
   BX       Burglary Test
   BZ       Missing Supervision
   CA       Automatic Closing
   CD       Closing Delinquent
   CE       Closing Extend
   CF       Forced Closing
   CG       Close Area
    CI      Fail to Close
    CJ      Late Close
   CK       Early Close
   CL       Closing Report
   CM       Missing Alarm - Recent Closing
   CO       Command Sent
   CP       Automatic Closing
   CQ       Remote Closing
   CR       Recent Closing
   CS       Closing Keyswitch
   CT       Late to Open
   CW       Was Force Armed
   CX       Custom Function Executed
   CZ       Point Closing
   DA       Card Assigned
   DB       Card Deleted
   DC       Access Closed
   DD       Access Denied
DE    Request to Enter
DF    Door Forced
DG    Access Granted
DH    Door Left Open - Restoral
 DI   Access Denied – Passback
DJ    Door Forced - Trouble
DK    Access Lockout
DL    Door Left Open - Alarm
DM    Door Left Open - Trouble
DN    Door Left Open (non-alarm, non-trouble)
DO    Access Open
DP    Access Denied - Unauthorized Time
DQ    Access Denied Unauthorized Arming State
DR    Door Restoral
DS    Door Station
DT    Access Trouble
DU    Dealer ID
DV    Access Denied Unauthorized Entry Level
DW    Access Denied - Interlock
DX    Request to Exit
DY    Door Locked
DZ    Access Denied - Door Secured
EA    Exit Alarm
EE    Exit Error
 EJ   Expansion Tamper Restore
EM    Expansion Device Missing
EN    Expansion Missing Restore
ER    Expansion Restoral
ES    Expansion Device Tamper
ET    Expansion Trouble
EX    External Device Condition
EZ    Missing Alarm - Exit Error
FA    Fire Alarm
FB    Fire Bypass
FC    Fire Cancel
FG    Unverified Event – Fire
FH    Fire Alarm Restore
 FI   Fire Test Begin
 FJ   Fire Trouble Restore
FK    Fire Test End
 FL   Fire Alarm Silenced
FM    Fire Alarm - Cross Point
FQ    Fire Supervisory Trouble Restore
FR    Fire Restoral
FS    Fire Supervisory
FT    Fire Trouble
FU    Fire Unbypass
FV    Fire Supervision Restore
FW    Fire Supervisory Trouble
FX    Fire Test
FY    Missing Fire Trouble
FZ    Missing Fire Supervision
GA    Gas Alarm
GB    Gas Bypass
GH    Gas Alarm Restore
GJ    Gas Trouble Restore
GR    Gas Restoral
GS    Gas Supervisory
GT    Gas Trouble
GU    Gas Unbypass
GX    Gas Test
HA    Holdup Alarm
HB    Holdup Bypass
HH    Holdup Alarm Restore
HJ    Holdup Trouble Restore
HR    Holdup Restoral
HS    Holdup Supervisory
HT    Holdup Trouble
HU    Holdup Unbypass
 IA   Equipment Failure Condition
 IR   Equipment Fail - Restoral
JA    User Code Tamper
JD    Date Changed
JH    Holiday Changed
 JK   Latchkey Alert
 JL   Log Threshold
JO    Log Overflow
 JP   User On Premises
 JR   Schedule Executed
 JS   Schedule Changed
 JT   Time Changed
 JV   User Code Changed
 JX   User Code Deleted
 JY   User Code Added
 JZ   User Level Set
KA    Heat Alarm
KB    Heat Bypass
KH    Heat Alarm Restore
 KJ   Heat Trouble Restore
KR    Heat Restoral
KS    Heat Supervisory
KT    Heat Trouble
KU    Heat Unbypass
LB    Local Program
LD    Local Program Denied
LE    Listen-in Ended
LF    Listen-in Begin
LR    Phone Line Restoral
LS    Local Program Success
LT    Phone Line Trouble
LU    Local Program Fail
LX    Local Programming Ended
MA    Medical Alarm
MB    Medical Bypass
MH    Medical Alarm Restore
MI    Message
MJ    Medical Trouble Restore
MR    Medical Restoral
MS    Medical Supervisory
MT    Medical Trouble
MU    Medical Unbypass
NA    No Activity
NC    Network Condition
NF    Forced Perimeter Arm
NL    Perimeter Armed
NM    Perimeter Armed, User Defined
NR    Network Restoral
NS    Activity Resumed
NT    Network Failure
OA    Automatic Opening
OC    Cancel Report
OG    Open Area
OH    Early to Open from Alarm
OI    Fail to Open
OJ    Late Open
OK    Early Open
OL    Late to Open from Alarm
OP    Opening Report
OQ    Remote Opening
OR    Disarm From Alarm
OS    Opening Keyswitch
OT    Late To Close
OU    Output State – Trouble
OV    Output State – Restore
OZ    Point Opening
PA    Panic Alarm
PB    Panic Bypass
PH    Panic Alarm Restore
 PJ   Panic Trouble Restore
PR    Panic Restoral
PS    Panic Supervisory
PT    Panic Trouble
PU    Panic Unbypass
QA    Emergency Alarm
QB    Emergency Bypass
QH    Emergency Alarm Restore
QJ    Emergency Trouble Restore
QR    Emergency Restoral
QS    Emergency Supervisory
QT    Emergency Trouble
QU    Emergency Unbypass
RA    Remote Programmer Call Failed
RB    Remote Program Begin
RC    Relay Close
RD    Remote Program Denied
RN    Remote Reset
RO    Relay Open
RP    Automatic Test
RR    Power Up
RS    Remote Program Success
RT    Data Lost
RU    Remote Program Fail
RX    Manual Test
RY    Test Off Normal
SA    Sprinkler Alarm
SB    Sprinkler Bypass
SC    Change of State
SH    Sprinkler Alarm Restore
 SJ   Sprinkler Trouble Restore
SR    Sprinkler Restoral
SS    Sprinkler Supervisory
ST    Sprinkler Trouble
SU    Sprinkler Unbypass
TA    Tamper Alarm
TB    Tamper Bypass
TC    All Points Tested
TE    Test End
TH    Tamper Alarm Restore
 TJ   Tamper Trouble Restore
TP    Walk Test Point
TR    Tamper Restoral
TS    Test Start
TT    Tamper Trouble
TU    Tamper Unbypass
TW    Area Watch Start
TX    Test Report
TZ    Area Watch End
UA    Untyped Zone Alarm
UB    Untyped Zone Bypass
UG    Unverified Event – Untyped
UH    Untyped Alarm Restore
UJ    Untyped Trouble Restore
UR    Untyped Zone Restoral
US    Untyped Zone Supervisory
UT    Untyped Zone Trouble
UU    Untyped Zone Unbypass
UX    Undefined
UY    Untyped Missing Trouble
UZ    Untyped Missing Alarm
 VI   Printer Paper In
VO    Printer Paper Out
VR    Printer Restore
VT    Printer Trouble
VX    Printer Test
VY    Printer Online
VZ    Printer Offline
WA    Water Alarm
WB    Water Bypass
WH    Water Alarm Restore
WJ    Water Trouble Restore
WR    Water Restoral
WS    Water Supervisory
WT    Water Trouble
WU    Water Unbypass
XA    Extra Account Report
XE    Extra Point
XF    Extra RF Point
XH    RF Interference Restoral
 XI   Sensor Reset
 XJ   RF Receiver Tamper Restoral
XL    Low Received Signal Strength
XM    Missing Alarm - Cross Point
XQ    RF Interference
XR    Transmitter Battery Restoral
XS    RF Receiver Tamper
XT    Transmitter Battery Trouble
XW    Forced Point
XX    Fail to Test
YA    Bell Fault
YB    Busy Seconds
YC    Communications Fail
YD    Receiver Line Card Trouble
YE    Receiver Line Card Restored
YF    Parameter Checksum Fail
YG    Parameter Changed
YH    Bell Restored
 YI   Overcurrent Trouble
 YJ   Overcurrent Restore
YK    Communications Restoral
YM    System Battery Missing
YN    Invalid Report
YO    Unknown Message
YP    Power Supply Trouble
YQ    Power Supply Restored
YR    System Battery Restoral
YS    Communications Trouble
YT    System Battery Trouble
YU    Diagnostic Error
YW    Watchdog Reset
YX    Service Required
YY    Status Report
YZ    Service Completed
ZA    Freeze Alarm
ZB    Freeze Bypass
ZH    Freeze Alarm Restore
 ZJ   Freeze Trouble Restore
ZR    Freeze Restoral
ZS    Freeze Supervisory
ZT    Freeze Trouble
ZU    Freeze Unbypass
Long Description
An attempt to substitute an alternate alarm panel for a secure panel has been made
An event message was not sent due to User action
An analog fire sensor has been restored to normal operation
AC power has been restored
An analog fire sensor needs to be cleaned or calibrated
AC power has been failed
Burglary zone has been violated while armed
Burglary zone has been bypassed
Alarm has been cancelled by authorized user
A non-fire zone has been violated after a Swinger Shutdown on the zone
A non-fire zone restores to normal from a Swinger Trouble state
A point assigned to a Cross Point group has gone into alarm but the Cross Point remained normal
Alarm condition eliminated
Trouble condition eliminated
Burglary alarm w/cross point also in alarm - alarm verified
Alarm/trouble condition has been eliminated
Unsafe intrusion detection system condition
Burglary zone disabled by fault
Zone bypass has been removed
A burglary alarm has occurred and been verified within programmed conditions. (zone or point not sent)
Burglary zone activated during testing
A non-fire Supervisory point has gone missing
System armed automatically
The system has not been armed for a programmed amount of time
Extend closing time
System armed, some zones not ready
System has been partially armed
An area has not been armed at the end of the closing window
An area was armed after the closing window
An area was armed before the closing window
System armed, normal
A point has gone missing within 2 minutes of closing
A command has been sent to an expansion/peripheral device
System armed automatically
The system was armed from a remote location
An alarm occurred within five minutes after the system was closed
Account has been armed by keyswitch
System was not disarmed on time
Header for a force armed session, forced point msgs may follow
The panel has executed a preprogrammed set of instructions
A point, as opposed to a whole area or account, has closed
An access ID has been added to the controller
An access ID has been deleted from the controller
Access to all users prohibited
Access denied, unknown code
An access point was opened via a Request to Enter device
Door opened without access request
Door access granted
An access point in a Door Left Open state has restored
Access denied because credential has not exited area before attempting to re-enter same area
An access point has been forced open in an unarmed area
Access denied, known code
An open access point when open time expired in an armed area
An open access point when open time expired in an unarmed area
An access point was open when the door cycle time expired
Access to authorized users allowed
An access request was denied because the request is occurring outside the user’s authorized time window(s)
An access request was denied because the user was not authorized in this area when the area was armed
Access alarm/trouble condition eliminated
Identifies door for next report
Access system trouble
Dealer ID number
An access request was denied because the user is not authorized in this area
An access request was denied because the doors associated Interlock point is open
An access point was opened via a Request to Exit device
The door’s lock has been engaged
An access request was denied because the door has been placed in an Access Closed state
An exit zone remained violated at the end of the exit delay period
An exit zone remained violated at the end of the exit delay period
Expansion device tamper restoral
Expansion device missing
Expansion device communications re-established
Expansion device trouble eliminated
Expansion device enclosure tamper
Expansion device trouble
A specific reportable condition is detected on an external device
A point remained missing at the end of the exit delay period
Fire condition detected
Zone has been bypassed
A Fire Alarm has been cancelled by an authorized person
A point assigned to a Cross Point group has gone into alarm but the Cross Point remained normal
Alarm condition eliminated
The transmitter area's fire test has begun
Trouble condition eliminated
The transmitter area's fire test has ended
The fire panel’s sounder was silenced by command
Fire Alarm with Cross Point also in alarm verifying the Fire Alarm
A fire supervisory zone that was in trouble condition has now restored to normal
Alarm/trouble condition has been eliminated
Unsafe fire detection system condition
Zone disabled by fault
Bypass has been removed
A fire supervision zone that was in alarm has restored to normal
A fire supervisory zone is now in a trouble condition
Fire zone activated during test
A fire point is now logically missing
A Fire Supervisory point has gone missing
Gas alarm condition detected
Zone has been bypassed
Alarm condition eliminated
Trouble condition eliminated
Alarm/trouble condition has been eliminated
Unsafe gas detection system condition
Zone disabled by fault
Bypass has been removed
Zone activated during test
Silent alarm, user under duress
Zone has been bypassed
Alarm condition eliminated
Trouble condition eliminated
Alarm/trouble condition has been eliminated
Unsafe holdup system condition
Zone disabled by fault
Bypass has been removed
A specific, reportable condition is detected on a device
The equipment condition has been restored to normal
Too many unsuccessful attempts have been made to enter a user ID
The date was changed in the transmitter/receiver
The transmitter's holiday schedule has been changed
A designated user passcode has not been entered during a scheduled time window
The transmitter's log memory has reached its threshold level
The transmitter's log memory has overflowed
A designated user passcode has been used to gain access to the premises.
An automatic scheduled event was executed
An automatic schedule was changed
The time was changed in the transmitter/receiver
A user's code has been changed
A user's code has been removed
A user’s code has been added
A user’s authority level has been set
High temperature detected on premise
Zone has been bypassed
Alarm condition eliminated
Trouble condition eliminated
Alarm/trouble condition has been eliminated
Unsafe heat detection system condition
Zone disabled by fault
Bypass has been removed
Begin local programming
Access code incorrect
The listen-in session has been terminated
The listen-in session with the RECEIVER has begun
Phone line restored to service
Local programming successful
Phone line trouble report
Local programming unsuccessful
A local programming session has been terminated
Emergency assistance request
Zone has been bypassed
Alarm condition eliminated
A canned message is being sent
Trouble condition eliminated
Alarm/trouble condition has been eliminated
Unsafe system condition exists
Zone disabled by fault
Bypass has been removed
There has been no zone activity for a programmed amount of time
A communications network has a specific reportable condition
Some zones/points not ready
An area has been perimeter armed
A user defined area has been perimeter armed
A communications network has returned to normal operation
A zone has detected activity after an alert
A communications network has failed
System has disarmed automatically
Untyped zone cancel
System has been partially disarmed
An area in alarm was disarmed before the opening window
An area has not been armed at the end of the opening window
An area was disarmed after the opening window
An area was disarmed before the opening window
An area in alarm was disarmed after the opening window
Account was disarmed
The system was disarmed from a remote location
Account in alarm was reset/disarmed
Account has been disarmed by keyswitch
System was not armed on time
An output on a peripheral device or NAC is not functioning
An output on a peripheral device or NAC is back to normal operation
A point, rather than a full area or account, disarmed
Emergency assistance request, manually activated
Panic zone has been bypassed
Alarm condition eliminated
Trouble condition eliminated
Alarm/trouble condition has been eliminated
Unsafe system condition exists
Zone disabled by fault
Panic zone bypass has been removed
Emergency assistance request
Zone has been bypassed
Alarm condition has been eliminated
Trouble condition has been eliminated
Alarm/trouble condition has been eliminated
Unsafe system condition exists
Zone disabled by fault
Bypass has been removed
Transmitter failed to communicate with the remote programmer
Remote programming session initiated
A relay has energized
Access passcode incorrect
A TRANSMITTER was reset via a remote programmer
A relay has de-energized
Automatic communication test report
System lost power, is now restored
Remote programming successful
Dialer data lost, transmission error
Remote programming unsuccessful
Manual communication test report
Test signal(s) indicates abnormal condition(s) exist
Sprinkler flow condition exists
Sprinkler zone has been bypassed
An expansion/peripheral device is reporting a new condition or state change
Alarm condition eliminated
Trouble condition eliminated
Alarm/trouble condition has been eliminated
Unsafe sprinkler system condition
Zone disabled by fault
Sprinkler zone bypass has been removed
Alarm equipment enclosure opened
Tamper detection has been bypassed
All point tested
Communicator restored to operation
An Expansion Device’s tamper switch restores to normal from an Alarm state
An Expansion Device’s tamper switch restores to normal from a Trouble state
This point was tested during a Walk Test
Alarm equipment enclosure has been closed
Communicator taken out of operation
Equipment enclosure opened in disarmed state
Tamper detection bypass has been removed
Area watch feature has been activated
An unspecified (manual or automatic) communicator test
Area watch feature has been deactivated
Alarm condition from zone of unknown type
Zone of unknown type has been bypassed
A point assigned to a Cross Point group has gone into alarm but the Cross Point remained normal
Alarm condition eliminated
Trouble condition eliminated
Alarm/trouble condition eliminated from zone of unknown type
Unsafe condition from zone of unknown type
Trouble condition from zone of unknown type
Bypass on zone of unknown type has been removed
An undefined alarm condition has occurred
A point or device which was not armed is now logically missing
A point or device which was armed is now logically missing
TRANSMITTER or RECEIVER paper in
TRANSMITTER or RECEIVER paper out
TRANSMITTER or RECEIVER trouble restored
TRANSMITTER or RECEIVER trouble
TRANSMITTER or RECEIVER test
RECEIVER’S printer is now online
RECEIVER’S printer is now offline
Water detected at protected premises
Water detection has been bypassed
Water alarm condition eliminated
Water trouble condition eliminated
Water alarm/trouble condition has been eliminated
Water unsafe water detection system condition
Water zone disabled by fault
Water detection bypass has been removed
CS RECEIVER has received an event from a non-existent account
Panel has sensed an extra point not specified for this site
Panel has sensed an extra RF point not specified for this site
A radio device is no longer detecting RF Interference
A user has reset a sensor
A Tamper condition at a premises RF Receiver has been restored
The RF signal strength of a reported event is below minimum level
Missing Alarm verified by Cross Point in Alarm (or missing)
A radio device is detecting RF Interference
Low battery has been corrected
A Tamper condition at a premises receiver is detected
Low battery in wireless transmitter
A point was forced out of the system at arm time
A specific test from a panel was not received
A trouble condition has been detected on a Local Bell, Siren, or Annunciator
Percent of time receiver's line card is on-line
RECEIVER and TRANSMITTER
A line card identified by the passed address is in trouble
A line card identified by the passed address is restored
System data corrupted
A TRANSMITTER’S parameters have been changed
A trouble condition has been restored on a Local Bell, Siren, or Annunciator
An Expansion Device has detected an overcurrent condition
An Expansion Device has restored from an overcurrent condition
TRANSMITTER has resumed communication with a RECEIVER
TRANSMITTER/RECEIVER battery is missing
TRANSMITTER has sent a packet with invalid data
An unknown message was received from automation or the printer
TRANSMITTER/RECEIVER has a problem with the power supply
TRANSMITTER’S/RECEIVER’S power supply has been restored
Low battery has been corrected
RECEIVER and TRANSMITTER
Low battery in control/communicator
An expansion/peripheral device is reporting a diagnostic error
The TRANSMITTER created an internal reset
A TRANSMITTER/RECEIVER needs service
This is a header for an account status report transmission
Required TRANSMITTER / RECEIVER service completed
Low temperature detected at premises
Low temperature detection has been bypassed
Alarm condition eliminated
Trouble condition eliminated
Alarm/trouble condition has been eliminated
Unsafe freeze detection system condition
Zone disabled by fault
Low temperature detection bypass removed
  Address Field
   Condition number
     Zone or point
     Zone or point
       Unused
     Zone or point
       Unused
     Zone or point
     Zone or point
     User number
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Area number
     Zone or point
     Zone or point
     Area number
     Area number
     User number
     User number
     Area number
     Area number
     User number
     User number
     User number
     Zone or point
   Condition number
     User number
     User number
     User number
     Zone or point
     Area number
     Area number
Custom Functionnumber
     Zone or point
     User number
     User number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
     Door number
        Unused
       Dealer ID
     Door number
     Door number
     Door number
     Door number
     Door number
     Zone or point
     User number
Expansion devicenumber
Expansion devicenumber
Expansion devicenumber
   Expander number
Expansion devicenumber
   Expander number
    Device number
     Point number
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Area number
     Zone or point
     Area number
     Zone or point
     Point number
     Zone or point
     Zone or point
     Zone or point
     Zone or point
     Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Point number
Point number
Area number
User number
User number
User number
  Unused
  Unused
User number
Area number
User number
User number
User number
User number
User number
User number
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
Zone or point
  Unused
     Unused
     Unused
     Unused
  Line number
     Unused
  Line number
     Unused
     Unused
 Zone or point
 Zone or point
 Zone or point
Message number
 Zone or point
 Zone or point
 Zone or point
 Zone or point
 Zone or point
 Zone number
Network number
 Area number
 Area number
 Area number
Network number
 Zone number
Network number
 Area number
 User number
 Area number
 User number
 Area number
 User number
 User number
 User number
 User number
 User number
 User number
 Zone or point
 User number
Output number
Output number
 Zone or point
 Zone or point
 Zone or point
 Zone or point
 Zone or point
 Zone or point
 Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
     Unused
     Unused
 Relay number
     Unused
     Unused
 Relay number
     Unused
     Unused
     Unused
  Line number
     Unused
  User number
  Zone or point
  Zone or point
  Zone or point
Condition number
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
     Unused
     Unused
     Unused
     Unused
 Point number
  Zone or point
     Unused
  Zone or point
  Zone or point
     Unused
     Unused
     Unused
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
     Unused
  Zone or point
  Zone or point
 Printer number
 Printer number
 Printer number
 Printer number
 Printer number
     Unused
     Unused
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
     Unused
  Point number
  Point number
Receiver number
  Zone or point
Receiver number
Receiver number
  Zone or point
Receiver number
  Zone or point
Receiver number
  Zone or point
  Zone or point
     Unused
     Unused
Line card number
    Unused
Line card number
Line card number
     Unused
     Unused
    Unused
    Unused
    Unused
    Unused
    Unused
    Unused
    Unused
    Unused
    Unused
    Unused
    Unused
    Unused
Condition number
    Unused
    Unused
    Unused
   Mfr defined
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
  Zone or point
Description/Event                     Automation Message   TLINK
Panel Absent                          ET0001                  TL-250
Panel Restored                        ER0001                  TL-250
FTC1 Alarm                            YC0001                  TL-250
FTC1 Restoral                         YK0001                  TL-250
FTC2 Alarm                            YC0002                  TL-250
FTC2 Restoral                         YK0002                  TL-250
PC5108 Tamper Alarm                   ES0000                  TL-250
PC5108 Tamper Restoral                EJ0000                  TL-250
PC5108 Absent                         ET0002                  TL-250
PC5108 Restored                       ER0002                  TL-250
Keyswitch Arm                         CS0000                  TL-250
Keyswitch Disarm                      OS0000                  TL-250
Remote Programming Start              RB0000                  TL-250
Remote Programming End                RS0000                  TL-250
Local Programming Start               LB0000                  TL-250
Local Programming End                 LS0000                  TL-250
Internal Comm. Error                  YC0000                  TL-250

Zone Alarms                           UA-XXX                  TL-150
Zone Alarm Restorals                  UH-XXX                  TL-150
[F] Alarm                             FA-000                  TL-150
[A] Alarm                             MA-000                  TL-150
[P] Alarm                             PA-000                  TL-150
[F] Alarm Restoral                    FH-000                  TL-150
[A] Alarm Restoral                    MH-000                  TL-150
[P] Alarm Restoral                    PH-000                  TL-150
2-wire Smoke Alarm                    FA-000                  TL-150
2-wire Smoke Alarm Restoral           FH-000                  TL-150
AC Trouble                            AT-000                  TL-150
AC Trouble Restore                    AR-000                  TL-150
Duress Alarm                          HA-000                  TL-150
Fire Trouble Alarm                    FT-000                  TL-150
Fire Trouble Alarm Restoral           FJ-000                  TL-150
Low Battery Trouble                   YT-000                  TL-150
Low Battery Trouble Restore           YR-000                  TL-150
Bell Circuit Trouble                  YH-000                  TL-150
Bell Circuit Trouble Restore          YA-000                  TL-150
General Supervisory Trouble           ET-000                  TL-150
General Supervisory Trouble Restore   ER-000                  TL-150
General System Trouble                YX-000                  TL-150
General System Trouble Restore        YZ-000                  TL-150
Opening After Alarm                   OR-000                  TL-150
Partial Closing                       CF-000                  TL-150
TLM Trouble (line number)             LT-XXX                  TL-150
TLM Trouble Restore (line number)     LR-XXX                  TL-150
Periodic Test                          RP-000   TL-150
Periodic Test with Trouble             RY-000   TL-150
Recent Closing                         CR-000   TL-150
Expansion Module Supervisory Trouble   UA-000   TL-150
Expansion Module Supervisory Restore   UH-000   TL-150
Zone Tampers                           TA-XXX   TL-150
Zone Tamper Restorals                  TR-XXX   TL-150
Zone Troubles                          UT-XXX   TL-150
Zone Trouble Restorals                 UJ-XXX   TL-150
General System Tamper                  ES-000   TL-150
General System Tamper Restoral         EJ-000   TL-150
FTC Restoral                           YK-000   TL-150

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:164
posted:9/23/2012
language:English
pages:44