Docstoc

Cisco CCNP Route-BGP Troubleshooting

Document Sample
Cisco CCNP Route-BGP Troubleshooting Powered By Docstoc
					         Cisco CCNP Route – BGP Troubleshooting
Every time you troubleshoot your BGP (Border Gateway Protocol), always follow a
tried and tested troubleshooting model. That way, you can work more efficiently and
probably even resolve the problem much faster. We usually follow an 8-point
troubleshooting model like the one below:
 Define the problem
 Gather the facts
 Document the facts
 Consider the possibilities
 Create an action plan
 Implement the action plan
 Repeat until resolution
 Document the solution

Just like in most protocols, there are some very specific, common issues and
problems, as well as their corresponding solutions. Here in our article on BGP
troubleshooting, we’ll be looking at these four potential problems/issues:
    1. Neighbor relationship problems
    2. Route advertisement issues
    3. Routes missing from the table
    4. Address summarization problems


Neighbor Relationship Problems
There are a number of possible reasons that may prevent neighbors from
establishing a relationship. Here are some of the most common causes of neighbor
relationship problems: Possible Cause: Layer 2 or Interface is down

If the Layer 2 process or Interface is down, it may prevent a neighbor relationship
from forming. The easiest way to determine that this is the problem when it’s stuck
in the Active or Idle state is by executing the show interface <slot/port>. For
example, execute: show interfaces fastethernet 0/0 or show interfaces
gigabitethernet 0/0 When the output is displayed, look at the interface that’s facing
the BGP peer. You should be able to see a line where it says something like:
Fast Ethernet 0/0 is up, line protocol is up.

The first part (Fast Ethernet 0/0 is up) is talking about the physical hardware portion,
while the second part (line protocol is up) is talking about the Layer 2 process.

So if you see something like: Fast Ethernet 0/0 is up, line protocol is down, that
means the physical interface is fine but Ethernet keep alive are not sent/received on
the interface. Sometimes, the reason is that something isn’t plugged-in on the other
side. Another reason could be you simply have a bad cable.
                                                    http://blog.router-switch.com/
If, however, the interface shows to be administratively down, then you can remedy
that by simply issuing the no shutdown command on the interface.

In figuring out Layer 1 and Layer 2 problems, always start at Layer 1 and work your
way up. Troubleshoot and solve the Layer 1 and Layer 2 issues on that particular
interface. If it’s a hardware failure, if it’s a cable failure, or something more subtle,
this method will be the best way to take care of this particular cause. Possible Cause:
Incorrect IP address used in neighbor statement in BGP An incorrect IP address in the
neighbor statement in BGP may also cause neighbor relationship problems.

Consider this diagram:




So, for example, in router R1, the configuration should be: router bgp
65001 neighbor 10.99.99.6 remote-as 65006 (this is the neighbor statement for R6,
for peering)

Conversely, on router R6, the statement in the configuration should be: router bgp
65006neighbor 10.99.99.1 remote-as 65001 If, for example, the IP address on either
R1 or R6 is wrong, the relationship will not form. So the easiest way to figure out if
there’s a problem is to first execute the show ip bgp summary command. It will
show you the state of the neighbor relationship, how many prefixes if any are being
received, and whether the neighbor is stuck in Idle or Active state.

In addition to that, you can also execute the show running config command to verify
that the peer address in the neighbor statements are correctly configured in BGP.

One of the things that’s going to be helpful is to: go in using PuTTY, SecureCRT, Tera
Term or whatever terminal services program you’re most comfortable with; highlight
the BGP section; paste the configuration into Notepad; and then go into the neighbor
                                                     http://blog.router-switch.com/
router and do the same thing. See if the neighbor configuration statements are in
fact correct. If they’re not correct, delete the neighbor statement and recreate them
with the correct IP addresses. Possible Cause: Configured eBGP peers are not
directly connected although eBGP peers that aren’t directly connected can still have
neighbor relationships, an additional command must be used and a special path
must be in place for the neighbor relationship to work.

You can determine whether the neighbor is more than one hop away by executing
the traceroute <peer ip> command. You’ll be able to tell very easily by the number of
different sections and hops shown in the output.

Once you discover that the neighbor is in fact more than one hop away, you can go
back into the BGP configuration and put in the statement: neighbor <peer ip>
ebgp-multihop <ttl>. ttlstands for time-to-live, which can be a value from 1 to 255
and which refers to the maximum number of hops that can be taken to reach the
peer. If it’s 2 hops away, you put 2. If it’s 3 hops away, you put 3, and so on. You may
also leave that parameter blank. If you do that, the default value of 255 will be
applied.

Another thing you can use is the show tcp command, which you execute in the
command-line. It will show you whether a TCP connection is up and in progress with
that particular neighbor. Subsequently, it will allow you to verify establishment of a
TCP session on port 179 toward a BGP peer. Possible Cause: Misconfigured neighbor
authentication Another cause that’s very common for neighbor relationships not
forming in BGP is the failure to configure the correct key in the password statement.

If you do a show ip bgp summary and you see that the neighbor relationships are
indeed stuck in Active or Idle, the easiest way to resolve this is to execute the show
running configcommand and then verify that the neighbor <peer ip> password
<key> command is present on both peers and that the configured keys match.

Again, it would help if you copy those snippets and paste them into Notepad. That
way, you can view the snippets all by themselves as you try to compare them and
spot anything missing or mistyped. Remember that the key is case-sensitive. If that
statement is incorrect, you don’t have to delete the entire configuration. Just
recreate the neighbor <peer ip> password <key> statements on both BGP
peers. Possible Cause: Unicast traffic being blocked between devices this possible
cause for neighbor relationships not forming is not as common as those mentioned
earlier. However, it’s still a possible cause nevertheless. In this case, Unicast traffic
between the peers is being blocked. Blocking can be caused by a firewall, an access
list, or a variety of different things.

Most likely, it’s going to be something configured on one or the other peers that may
be blocking it but if there’s an intermediate device, then you’ll have to take a good
                                                     http://blog.router-switch.com/
look at that device’s configuration as well.

But in the particular device in question, execute the show ip interface and show
access list commands. Look at all the access lists, see if anything is being applied on
the interface facing that particular neighbor, and if there is, either alters the access
list to allow the traffic or you may have to alter it altogether.

Once you’re done with that, make sure everything is correct, make sure that the
statements for peering are correct, and make sure show interface shows
up/up. Possible Cause: Neighbor statement misconfigured under BGP There may be
other things in the neighbor statement that may cause problems in neighbor
relationships. For instance, timers may be mismatched.

To check whether something’s incorrect with the neighbor statement in BGP, start by
executing the show ip bgp summary. You’ll want to know first whether the
neighbor relationships aren’t even shown. If they aren’t shown, then that means the
neighbor relationship is not being established and it has not been configured at all.

If it has been configured, you’re going to see at least Active or Idle as a result of that
command. At that point, you can also execute the show running-config in order to be
able to go through and parse through the configuration. If there are only a few
entries, this task is going to be very easy.

However, if it’s really long, then it can be difficult. If so, then paste it to Notepad so
you can use the search function to find specifically what you’re looking for. If you
know a specific IP that’s correct, you can go to that particular IP where you’ll find the
entire string of numbers and commands, which will be listed in order. From that you
can gather some information and determine possible causes.

Once you’ve pinpointed what’s wrong, you can delete and recreate the neighbor
statements with the correct IP address combinations.


Route Advertisement Issues
Possible Cause: Automatic network summarization is in effect Although there can be
a number of things that may prevent routes from being advertised correctly, one of
the primary culprits is the auto-summary command.

Both BGP and EIGRP have automatic summarization enabled by default. If you don’t
execute the no-auto summary command when you configure BGP, it’s going to
automatically summarize into a classical boundary.

To check whether summarization is enabled, use the show ip protocols command.
Look for the statement that says, Automatic route summarization is <disabled |
                                                     http://blog.router-switch.com/
enabled>. In EIGRP, it will say, “... is in effect” or “... is not in effect”.

So in BGP, you’ll want to see “disabled”. If it says something different, then you will
need to go back into the BGP router configuration and execute the no
auto-summary command.Possible Cause: The advertisement does not match a route
in the IP routing table If the particular route being injected into BGP by
the network statement is not matching a route in the IP routing table, then you can
encounter route advertisement problems.

To remedy this, execute the show ip route command to discover whether the route
exists in the current routing table. If it is not there, troubleshoot the local router and
the IGP to determine the cause. See whether it was even configured in the router or
check the IGP to see if there is a particular issue that’s preventing the route from
being installed in the routing table.

Once you see the cause of the problem, correct it. Possible Cause: Route
synchronization is enabled By default, route synchronization is enabled in BGP.
Synchronization means that it has to exist in the IP routing table through an IGP,
static routes, or other means, or BGP will not advertise the route.

To solve this problem, first execute the show ip protocols command and check
whether the statement says IGP synchronization is enabled. If so, go back into the
BGP configuration and put in the no synchronization command in order for that
behavior to be turned off. Possible Cause: Route redistribution is not configured or is
misconfigured One more cause for a problem with route advertisement issues may
have to do with redistribution. Basically, if redistribution has not been configured,
BGP won’t pull those routes in. The table has to be populated either through direct
injection into BGP using the network statement or through redistribution.

You may use the show ip protocols command and look to see if redistribution has
been configured. If it has, then investigate some more to see where the problem lies.
It could be that you may have put in an incorrect AS number or a process ID relating
to OSPF.


Routes Missing from Table
Now, aside from routes not being advertised correctly in BGP, you may find that
certain routes are not showing up in the routing table, which is a little bit of a
different issue. They sound the same but route advertisement is actually the BGP
process announcing something out, and whether or not something’s being installed
in the routing table is a separate issue altogether.Possible Cause: Default route
misconfigured If the default route is not showing up, then it’s probably simply
because it was not configured correctly. To investigate, execute the show ip
route and see whether there is a route to 0.0.0.0 network to begin with. If it’s
                                                          http://blog.router-switch.com/
missing from the table, it won’t be injected or advertised from BGP.

You may also execute the show running-config and verify whether the network
0.0.0.0 and the default-information originate statements are existing and correctly
configured in BGP. Add those statements if you find them missing. Possible Cause:
Route synchronization is enabled We discussed this earlier as a possible cause for
route advertisement issues, so just review that section if you want. Possible Cause:
iBGP neighbors not fully meshed You may have a problem with iBGP neighbors
because these neighbors are not full meshed. Remember, when the routes are being
advertised among iBGP peers, it has a ttl of 1. If they’re not all fully meshed, you
won’t be able to propagate routes correctly.

To verify that peerings are happening correctly, use the show ip bgp
neighbors command. You may also use the show running-config command and do a
little bit more investigative work in order to determine whether or not the neighbors
are in fact fully meshed.

If there are connections that are missing, configure them using the <peer ip>
remote-as <ASN> command. For example, let’s bring back the diagram we showed
you earlier.




If these were IBGP routers and there were direct connections between the Internet
Router and Router 1 as well as between Router 1 and Router 6, but there was no
connection between the Internet Router and Router 6, that would be a missing leg to
a fully-meshed environment.

So if you have that kind of missing connection, you can then use the <peer ip>
remote-as <ASN> command to remedy the problem.

Finally, execute the show ip bgp summary command, make sure that all the other
                                                   http://blog.router-switch.com/
peers that you’re looking for are indeed there and that each one of the neighbors
shows all the other peers that are required. That will be your best way of
determining whether or not a fully meshed relationship has been
configured. Possible Cause: iBGP next-hop is not reachable One of the ways for you to
check whether this is an issue is to do the show ip route command and examine the
IP routing table for the required static/IGP route. And this is true with even eBGP. If
the next-hop route is not reachable, it’s not going to be advertised.

If a static route is required, configure it using the ip route <prefix> <mask>
<next-hop>command. Now, if for some reason, the IGP is failing to install the route
leading to the iBGP next-hop address, you may have a whole other set of issues just
related to the IGP.

In that instance, you have to make sure you’re looking at BGP as one sort of
troubleshooting domain and the IGP as another. They depend on each other but they
can have different issues.

Address Summarization Problems
Possible Cause: No subnets in the routing table in the range of the aggregate
address In terms of address summarization problems, one common cause for an
aggregate not being advertised is because there isn’t some part of the IP address
range within the aggregate that exists already in the routing table.

The easiest way to check that is to execute the show ip route. See if any networks
within that range currently exist. If you were advertising an aggregate address
216.145.0.0 and the mask is 255.255.252.0 and there are no 216.145-any type
addresses in terms of the routing table, it’s not going to advertise the aggregate.

Execute the show running-config to verify that the aggregate address statement is
correctly configured. If it is not, delete and recreate the statement that need
corrections.


Relevant Debug and Show Commands
The troubleshooting process in BGP requires the use of several Show and a couple
of Debug commands that you should be familiar with. BGP Show Commands Show ip
protocols This will show the BGP status of your neighbor, your Autonomous System
Number (ASN), timer intervals, networks being advertised, and neighbors/gateways.
Consequently, it will be helpful in troubleshooting neighbor relationships, missing
routes, summarization issues, and filtering problems.

Here’s a portion of an output resulting from a show ip protocols command:



                                                   http://blog.router-switch.com/
Show ip route bgp This will show BGP routes advertised by neighbors, the
administrative distance, MED value (if any), and the route source/interface. These
information will be helpful in troubleshooting missing routes, summarization issues,
filtering problems, and general troubleshooting tasks.




Show ip bgp summaryThis will show your configured peer IP addresses, your ASN,
the number of messages received and sent, how long the session has been up, the
state (Active, Idle, etc.), and prefixes received. This will be helpful in troubleshooting
neighbor relationship issues, local configuration issues, and routing problems.




                                                     http://blog.router-switch.com/
 Show ip bgp neighborsThere are two forms of this command. The first one is
just show ip bgp neighbors, which will show you the IP address of neighbors, router
ID of neighbors, state of a neighbor, peer-group (if configured), BGP messages/types
received, and so forth.

However, you can also specify the peer ip address and then add either of these two
optional parameters received-routes and advertised-routes. Received-routes is for
routes being received by that particular neighbor, while advertised-routes is for
routes advertised out to a particular neighbor.

Here’s the syntax: show ip bgp neighbors [peer ip address] {received-routes |
advertised-routes} That will show you how many routes you are actually advertising
or receiving and can be extremely helpful in attacking problems associated with
routes missing and so forth. It can also be helpful in troubleshooting neighbor
relationships, local configuration issues, and other issues associated with BGP routes.

Here’s part of what I got when I issued the command: show ip bgp neighbors
10.6.6.6




Now, here’s part of what I got when I used show ip bgp neighbors 10.6.6.6
advertised-routes instead:
                                                   http://blog.router-switch.com/
Notice the default route that’s being advertised at the top, followed by a whole host
of prefixes.

Lastly, here’s part of what I got when I used show ip bgp neighbors 10.6.6.6
received-routes




 It’s practically the same type of information but it’s showing what’s being
received. Show ip bgp This shows the entire contents of the routing information base.
It will show your network mask/prefix, next-hop router, MED value, Local Preference
Value, Weight Value, AS path, and so forth.

In turn, that information is going to be helpful in troubleshooting missing routes,
filtering problems, and general troubleshooting tasks.
Now we go to the Debug commands.

BGP Debug Commands Debug commands display results that are more real-time
views of the situation compared to the results of the show commands, which mostly
                                                  http://blog.router-switch.com/
allow you only to look at settings.

debug ip bgp <peer ip> updates This will show you everything that has to do with
neighbor adjacencies and relationships. So it’s good for troubleshooting neighbor
relationships and routing update issues.




debug ip bgp events

This is helpful in looking at different network events like interfaces that go up and
down, processes that change, neighbor relationships that change, and so forth. It can
help in troubleshooting routing update issues, convergence issues, and interface
flapping.

Conclusion
That wraps up our discussion on BGP troubleshooting. I hope you learned a lot and I
look forward to having you here again.

More Cisco Certification Info, Tips:
CCNP TSHOOT: Cisco Troubleshooting Techniques & Procedures
Top Cisco Certification Books
Top 5 VoIP Concepts to Know for CCNA Voice—VoIP Basic for CCNA Voice Exam
How to Prepare for the CCIE Voice Written Exam?
Guide to Cisco CCNA Voice Exam 640-461…Reviews, Main Topics




                                                  http://blog.router-switch.com/

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:2
posted:8/31/2012
language:
pages:11