Bag Cage and Filter Cage by amritfiltration


More Info
									               AMRIT FILTRATION EQUIPMENT
Amrit filtration a complete range of standard and non-standard filter cage and bag cage
designed to suit the customer’s requirements and filter arrangements from circular, diamond,
oval, flat and star cages.

We manufacture replacement cages for almost every pulse type collector on the market. We fabricate
both carbon steel & Galvanized filter cages as well as epoxy coated in 8 to 24 vertical wire

                                           Filter cages are made on CNC machines for burr
                                           free finish, and are constructed of following
                                                MS wire
                                                GI wire
                                                304 stainless steel
                                                316/316-L stainless steel
                                                Other specially materials.

                                       BAG CAGE
                                       Amrit Filtration Equipments is one of the trusted
                                       manufacturers and suppliers of Bag Cage and Filter Cage.
                                       The products offered by us are availed by all major air
                                       pollution control systems manufacturers, end users
                                       markets and OEM's across the country. These cages are
                                       offered in a variety of coatings, techniques and metals.
      Available in MS, GI, SS304, SS 316
      Wire diameter from 3mm to 6
      8, 10, 12, 14, 16, 18, 20, 22, 24 vertical wires
      Ring distance 100 to 200 mm
      Top type , L shape flange, U shape flange, Welded venture
      Finishes - aluminum paint, epoxy paint, Zinc coating

Installation of Bag and Cage Assembly - Bottom Load (45 and 60 series)
   1. Inspect the cage for any signs of damage, warping, bent wires, or missing welds.

   2. Inspect the filter bag for any signs of mold, mildew, ripped seams, or holes.

   3. Be sure the wire cage has a bottom pan. Slip filter bag over the cage, centering the
      seam 1-1/2” or 2” either side of the split at the top of the cage roll band. Seam must be
      straight (not corkscrewed).

   4. Pull bag up and over the full length of the cage and fold the entire extra length over
      and down into the top of the cage. Make sure the bag bottom is tight against the cage
      pan. Smooth out all folds and pleats on the interior of the roll band.

   5. Slip the assembled bag and cage up onto the bag cup making sure to mate the male
      groove of the cage roll band top to the female groove of the bag cup.

   6. If you try to move the assembly up and down you will be able to tell if the grooves are
      properly aligned.

   7. Install the bag clamp on the assembly and tighten around the bag and cage at a point
      just above the groove on the cage. The clamp head should be located in the best
      direction for ease in tightening.
    8. Tighten the clamp until secure. You should not be able to rotate the assembly by hand
       if it is tight enough.

    9. Close the access door and tighten accordingly. You are ready to begin start-up
       procedures if all other preceding tasks and hook-ups are completed.

    10. It is recommended to double check the tightness of the bag and cage assembly
        approximately one month after the initial start-up.

A unique, patented system designed to alleviate the worst part of bag house
operation: Bag change outs.

Pop-Top 2.0 bags and cages are quicker and easier to install and remove than snap-in bags.
They are an improvement of our original design, which has been the preferred bag/cage
system for all maintenance personnel who have used it.

The new design incorporates an elastomeric collar that is more forgiving for holes with
tolerance variations or which have unfinished edges.

Result: if snap-in bags will work, Pop-Top 2.0 bags will work better!

Pop-Top 2.0 bag and cage assemblies will save you time and money, yet cost no more than
snap-in bags and cages. The elastomeric collar provides a leak-free seal which is easily released
during change out. Benefits include:

Change out takes about half the time of snap-in bags, reducing maintenance costs and

       No more stuck bags and cages.
       No clamps to deal with.
       Bag and cage can be removed together or separately.
       Easier change outs also reduce risk of wrist and back injuries.
Standard Pop-Top 2.0 bag and cage assemblies can be used in ambient conditions (up to 180°F)
wherever snap-in bags are used. Medium and high temperature versions available. They will fit
any bag house designed for 4.5 or 6 inch bags (51⁄16 and 61⁄4 holes).

Pop-Top 2.0 is especially suitable for applications, like cement, where bags tend to stick to their
cages. It is also the standard bag and cage system for new Mikro-Pulsaire baghouses.

Style: MikroPul Pop-Top
Hole dia. (in.): 51⁄16, 61⁄4
Bag length (ft.): 4, 6, 8, 10, 12
Media type: Polyester felt, Polypropylene felt, MikrotexMembrane/Polyester; High
Temperature, Other media available
Bag enhancements: wear strips, Ground wires, special coatings.

                                       AMRIT Filtration EQUIPMENTS
                                       Mr. Rajender Lohia – 9810347779
                                       Mr. Sarthak Lohia – 9871073914
                                       OFFICE ADDRESS
                                       I’st floor, shri shradha market, G.T. ROAD GHAZIABAD
                                       201001 (U.P.) INDIA
                                       PH. NO. - 0120 – 4371475, 2853227, 9871073915
                                       Email Us -
                                       Web -

To top