"FVTFVR412 MS 1 ae"
DIVISION 28 23 23 B. Inspect product upon delivery to assure that FVT/FVR412 SERIES – FIBER OPTIC specified products have been received. TRANSMITTER AND RECEIVER C. Store in original packaging in a climate ENGINEERING SPECIFICATIONS controlled environment. Storage Temperature not to exceed: -40˚ C to +85˚ C PART 1 - GENERAL 1.07 PROJECT/SITE CONDITIONS 1.01 SUMMARY A. Temperature Requirements: Products shall A. Fiber Optic Digital 4 Channel Video operate in an environment with an ambient Multiplexing System with two channels of bi- temperature range of –40˚ C to +75˚ C without directional data and one bi-directional contact the assistance of fan-forced cooling. closure. B. Humidity Requirements: Products shall operate 1.02 SECTION INCLUDES in an environment with relative humidity of 0% A. FVT/FVR412M1 Digital 4 Channel Video to 95% (non-condensing). If product is installed Multiplexing System with two channels of bi- in condensation conditions, unit shall have directional data and one bi-directional contact conformal coating applied to the printed circuit closure, multimode.– Standalone and Rack board. mount 1.08 WARRANTY B. FVT/FVR412S1 Digital 4 Channel Video A. Standard Communication Networks Multiplexing System with two channels of bi- Comprehensive Lifetime Warranty: ComNet directional data and one bi-directional contact warrants the product to be free of factory defects closure, single mode.– Standalone and Rack under manufacture’s Lifetime Warranty as mount submitted under article 1.05 (E) 1.03 REFERENCES PART 2 - PRODUCTS A. Underwriters Laboratory (UL) 2.01 MANUFACTURER B. Underwriters Laboratory Canada (ULC) A. Acceptable Manufacturer 1.04 SYSTEM DESCRIPTION Communication Networks A. Performance Requirements: Provide a Digital 4 3 Corporate Drive Channel Video/2 Channel Data Multiplexing Danbury CT 06810 System. USA B. The system shall utilize 1310/1550nm optics Telephone: 203 796-5300 capable of digitally encoding and decoding e-mail: sales@ComNet.net; four channels of video, four channels of bi- Internet URL: www.ComNet.net directional data and one bi-directional B. Substitutions: Not Permitted contact closure on one multimode optical C. All fiber optic modules shall be supplied from a fiber. (FVT/FVR412M1) single manufacturer. C. The system shall utilize 1310/1550nm optics 2.02 MANUFACTURED UNITS capable of digitally encoding and decoding A. Model Number Descriptions: Reference Table four channels of video, four channels of bi- A: Product Number Descriptions directional data and one bi-directional B. Model Compatibility Chart: Reference Table B: contact closure on one single mode optical Product Compatibility Chart fiber. (FVT/FVR412S1) 2.03 GENERAL SPECIFICATIONS 1.05 SUBMITTALS A. The Digital four channel video encoding and A. Product Data: Manufacturer’s printed product decoding system with two channels of bi-directional data sheet for each type of Transmitter/Receiver data and one bi-directional contact closure shall be a specified. ComNet FVT/FVR412 series module. The module B. Detail Drawings: Electrical and optical connect shall be capable of digitally encoding and decoding drawings. Product mounting template. four channels of full color video in real time in C. Manufacturer’s Installation and Operating NTSC, PAL or SECAM formats, two channels of bi- Manual: Printed installation and operating directional data and one bi-directional contact information for each type of closure. The module shall require no in-field Transmitter/Receiver specified. electrical or optical adjustments or in-line attenuators D. Test Reports: Manufacturer’s Printed Test to ease installation. The module shall transmit the Report via a Tektronics VM700A Video Test video, data and contact closure using state – of – the Generator verifying product performance meets – art digital encoding and decoding of the optical or exceeds the specified product performance signal. The module shall provide power, local video referenced in Part 2. presence, remote video presence, data transmitted E. Warranty: Manufacturer’s Printed Warranty and received and optical carrier detect status 1.06 DELIVERY, STORAGE AND HANDLING indicating LED’s for monitoring proper system A. Deliver materials in unopened factory packaging operation. The modules shall provide automatic re- with Manufacturer’s bar coding to the job site. settable solid-state current limiters and independent Project name/project number/date 00000 - 1 Section Title (Optional information, e.g., owner, A/E) voltage regulators on each module to reduce the A. Optical: ST chance of a single point failure of the system. The B. Power and Data: Terminal Block with Screw module shall be hot swappable in a rack mount Clamps system to reduce complete system shut down during C. Video: BNC (Gold Plated Center-PIN) maintenance or repair. The module shall have an 2.09 ELECTRICAL SPECIFICATIONS MTBF of >100,000 hours and operate in an A. Power: 8-15 VDC environment of –40˚ C to +75˚ C and relative B. Current Protection: Automatic re-settable solid- humidity between 0% to 95% (non-condensing). The state current limiters module shall be UL and ULC listed. The circuit C. Voltage Regulation: Solid-state, Independent on board shall be UL 94 flame rated and meet all PCI each board standards. All PC boards shall be designated with D. Circuit Board: UL 94 flame rated and meets all part number, PC board number and show appropriate PCI standards. revision number. Housing shall be of all metal E. Rack mount Card: Shall be hot-swappable with construction. All LED indicators and both electrical ComNet Model Number C1 (EIA 19” card cage) and mechanical connections shall be identified with 2.10 MECHANICAL SPECIFICATIONS silk-screened labels. The module shall have a lifetime A. Dimensions: 6.1” x 5.3” x 2.2” (15.5 cm x 13.5 warranty to reduce system life cycle cost in an event cm x 5.6 cm) of a module failure. B. Number of Rack Slots: 2 2.04 VIDEO SPECIFICATIONS C. Finish: Module shall be constructed of a metal A. Input Video: 1 volt pk-pk (75 ohms) enclosure with a powder coat finish with all B. # of Inputs and Output Channels: 4 connections and indicators silk-screened directly C. Bandwidth: 10 Hz – 6.5 MHz on unit. D. Differential Gain: < 4 % D. Weight: <2.0 lbs./0.9kg E. Differential Phase: < 0.7 ° E. This product shall conform to ComFit F. Tilt: <1% Technology. That is, all “stand alone” products G. Signal/Noise Ratio: 57dB @ maximum optical (sometimes called “box”) shall be identical in loss budget every respect, both electrically and physically, 2.05 DATA SPECIFICATIONS with the “rack” products so that only a single A. Data Channels:2 product may be used interchangeably for both B. Data Format: RS-232, RS-422, 2 or 4 wire RS- the “stand alone” and “rack” applications. All 422 with Tri-state Manchester Bi-Phase and ComFit products shall be supplied with a plug-in Sensornet module power supply, electrical connectors, and C. Data Rate: DC- 250 kbps (NRZ) mechanical parts to enable it to be used in “stand D. Bit Error Rate: <1 in 10‾9@ maximum optical alone” or “rack” configuration. All ComFit loss budget products shall mount directly to a wall without E. Operating Mode: Simplex or Full Duplex the need for special mounting brackets. 2.06 OPTICAL SPECIFICATIONS 2.11 ENVIRONMENTAL SPECIFICATIONS A. ComNet Model Number FVT/FVR412M1 A. MTBF: >100,000 Hours 1. Optical Fiber: 62.5/125 micron multimode B. Operating Temp: –40˚ C to +75˚ C 2. Number of Fibers Required: 1 C. Storage Temp: -40˚ C to +85˚ C 3. Optical Wavelength: 1310/1550nm D. Relative Humidity: 0% to 95% (non- 4. Optical Power Budget: 16 dB condensing). If product is installed under 5. Optical Attenuation: No manual adjustments condensation conditions, unit shall have required conformal coating applied to the printed circuit B. ComNet Model Number FVT/FVR412S1 board. (Add –C to model number for conformal 1. Optical Fiber: 9/125 micron single mode coated printed circuit board) 2. Number of Fibers Required: 1 2.12 ACCESSORIES 3. Optical Wavelength: 1310/1550nm A. Card Cage: ComNet Model Number C1 (EIA 4. Optical Power Budget: 23 dB 19” card cage) shall be available to house and 5. Optical Attenuation: No manual adjustments power rack mount modules. required B. Blank Panels: ComNet Model Number C1-BP 2.07 STATUS INDICATORS shall be available to cover unused rack slots. A. Video Input/Output sync for each channel: 2.13 CONTACT Video sync/Green – No Video Present/Red A. Contact Interface: Response Time 0.5msec B. Local and remote video present: Video B. Input: Dry Contact Closure present/Green – No Remote Video Present/Red C. Output: SPST Relay, 0.5 A Contact Rating – C. Data Transmit/Data received: Data TX/RX normally open Green, No Data Red PART 3 - EXECUTION D. Optical carrier detect: Detect Green, None Red 3.01 EXAMINATION 2.08 CONNECTORS A. Inspect modules before installation. Project name/project number/date 00000 - 2 Section Title (Optional information, e.g., owner, A/E) B. Modules shall be free of any cosmetic defects or 3. All optical fiber cables shall be properly damage. installed and terminated with the mating C. All optical connectors shall be covered with dust optical connectors as submitted in article caps and remain on the module until installing 2.07 (A). cable connectors to module. 4. The optical link shall be tested with either a D. Shipping box shall include the module, power power meter, at a minimum, or OTDR to supply and operations manual. ensure the link budget (overall path loss) 3.02 PREPARATION plus an added 3dB of optical safety margin A. Standalone Module (Surface Mount) does not exceed the optical power budget as 1. Shall be mounted on a properly prepared submitted in article 2.05. surface adequate for the size and weight of 5. All optical connectors on cable shall be module. The placement of the unit shall cleaned in compliance to optical connector allow provision for cable installation and manufactures specifications and covered maintenance as indicated on the approved with dust caps until connection to the fiber detail drawings and in compliance with the optic module. ComNet mounting template and installation 3.03 INSTALLATION manual. A. General: Locate fiber optic modules as indicated B. Rack Mount Module (19” Rack) on the approved detail drawings and install 1. Shall be installed in the ComNet Model module in compliance with the ComNet Number C1 card cage. Ensure the card cage installation and operations manual. is installed in a standard EIA 19” (482.6 3.04 TESTING mm) rack or wall standoff bracket adequate A. Testing the Fiber Optic Video Link. for the size and weight of the card cage. The 1. Verify that the coax and optic fibers are placement of the unit shall allow provision properly connected. for cable installation and maintenance as 2. Make sure that power is applied to all fiber indicated on the approved detail drawings optic modules, camera, and video monitor or and in compliance with the ComNet other equipment used in the system. installation manual. 3. The automatic gain control (AGC) indicator C. Optical Fibers LED should be lit confirming a presence of 1. Caution: NEVER look into the end of an a video signal. active optical fiber when using laser light 4. Successful video link operation should be output. Eye damage can occur. Wear eye visible at this point as witnessed by a good protection when cleaving, terminating, and quality video picture on the monitor. splicing fiber. 3.05 CLEANING 2. The number and type (multimode or single- A. Follow all instructions for proper use of solvents mode) of optical fiber shall meet the and adhesives used for termination and splicing. requirements of the ComNet model number B. At completion of the installation, dispose of all in article 2.05 used in the installation. fiber scraps properly. Project name/project number/date 00000 - 3 Section Title (Optional information, e.g., owner, A/E) MANUFACTURED UNITS REFERENCE TABLES Table A: Product Number Descriptions FVT412 SERIES DESCRIPTION OPTICAL MAXIMUM POWER DISTANCE BUDGET FVT412M1 MM Video/Data – 1300/1550 >, 1 Fiber 16 dB 2 miles (3 km) FVT412S1 SM Video/Data – 1300/1550 >, 1 Fiber 23 dB 43 miles (69 km) * Maximum distance is limited to optical loss of the fiber and any additional loss by connectors, splices and patch panels. FVR412 SERIES DESCRIPTION FVR412M1 MM Video/Data – 1300/1550 >, 1 Fiber FVR412S1 SM Video/Data – 1300/1550 >, 1 Fiber * Maximum distance is limited to optical loss of the fiber and any additional loss by connectors, splices and patch panels. Table B: Product Compatibility Chart TRANSMITTER COMPATIBLE RECEIVER FVT412M1 FVR412M1 FVT412S1 FVR412S1 END OF SECTION Project name/project number/date 00000 - 4 Section Title (Optional information, e.g., owner, A/E)