Docstoc

512+522+625+receivers

Document Sample
512+522+625+receivers Powered By Docstoc
					Setting Up Your
Replacement Remote




6.4 IR/UHF Remote Control
512, 522 and 625 Receivers
                             177320
1. Install the Batteries
Remove the remote battery cover and install the                     TUNE
                                                                    TV TO   *****
enclosed batteries. Replace the battery cover                        FAMILY ROOM


and attach the correct identification labels.


2. Test Your Remote
To turn your DISH receiver on, press and release
the POWER button on the front of your receiver.
Then, turn on your TV and press and release the
GUIDE button on your DISH remote.
If the programming guide displays                If the programming guide does not
on your TV, skip to Step 6.                      display, continue with Step 3.

3. Determine the Correct Side for the Remote Key
There is a removable, two-sided key at the bottom of your remote. Your remote
was shipped with the silver UHF side up.

Silver UHF Side Up:                                             Silver UHF Side
If your remote will be used to operate TV2, you must have
the silver UHF side up. TV2 is the TV located in a different
room than your receiver. If your remote will be used to
operate TV2, skip to Step 5.

Green IR Side Up:                                                Green IR Side
The green IR key can only be used to operate TV1. TV1 is the
TV located in the same room as your receiver. If your remote
will be used to operate TV1, continue with Step 4.


4. Flip the Remote Key (to Operate TV1)
A   Remove the battery cover and use your thumbnail
    to remove the key from the remote.




B   Flip the key and re-insert it into the remote so that
    the green IR side of the key is facing up.
5. Program the Remote to Control Your Receiver
                                                   System Info

A Press and                 The System                           Model ID
                                                           Receiver CA ID
                                                            Smart Card ID
                                                                              ViP625 DVR
                                                                              R0000000000-95
                                                                              S0000000000-01



  release the               Info screen                   Software Version
                                                         Boot Strap Version
                                                              Str
                                                                rap
                                                              Programming
                                                    Billing & Pro
                                                                ogramming
                                                                              DNASP103 Rev382
                                                                              ACT1MADD-N
                                                                              1111MADD
                                                                              1-800-333
                                                                              1-800-333-DISH (3474)
                                                                                       3-DISH


  SYSTEM INFO               will display.            Technical Assistance
                                                                 A
                                                           Internet Address
                                                           Internet
                                                             Receiver Mode
                                                             Rece
                                                                Location ID
                                                                L
                                                                 eiver
                                                                              1-800-333
                                                                              1-800-333-DISH (3474)
                                                                                       3-DISH
                                                                              http://www
                                                                              http://www.dishnetwork.com
                                                                              Dual Mode
                                                                                    Mode
                                                                              86700A00
                                                                                        w.dishnetwork.com

                                                                                       0:1111DA111
                                                                              86700A00:1111DA111


  button on the
                                                  Primary Remote Address
                                                              te
                                                          Remot                1       IR
                                                                                       IR
                                                          Remote
                                                Secondary Remot Address
                                                              te               5      UHF Pro Band B
                                                                                      U

                                                      Help              Done              Cancel

  front of your
  receiver.


B   Press and               The SAT mode
    release the             button will light
    SAT mode                up.
    button on
    your remote.


C   Press and               The SAT mode
    release the             button will light
    RECORD                  up again.
    button.



D   Press and               The System
    release the             Info screen
    SELECT button           will close and
    on the front of         programming
    your receiver to        will display.
    close the System
    Info screen.




E   Go to the TV            The
    where the               programming
    remote will be          guide will
    used. Press and         display on the
    release the             TV.
    GUIDE button
    on your remote.
6. Program the Remote to Control Your TV
Use the “Remote Control TV Codes” booklet that was included with your replacement
remote to find the code needed for your TV.

A   While facing the TV                                   All four mode
    where the remote                                      buttons will
    will be used, press                                   light up.
    and hold the TV
    mode button.

B   Enter the three-digit                                 The TV
    remote control code                                   mode button
    from the “Remote                                      will light up.
    Control TV Codes”
    booklet.


C   Press and release                                     The TV
    the POUND (#)                                         mode button
    button.                                               will flash
                                                          three times.



D   Press and release                                     The TV will
    the large, red                                        turn off.
    POWER button.



E   Press and release                                     The SAT
    the SAT mode                                          mode button
    button.                                               will light up.

F   Press and release                                     The TV will
    the TV POWER                                          turn on and
    button. Then, press                                   respond to
    VOLUME up or                                          remote                    VOL


    down to confirm                                       commands.*
    that the remote
    operates your TV.

Congratulations! You are now ready to enjoy DISH Network.
*If your TV does not respond to the DISH remote, try another three-digit remote control code.
Go to dish.com/support for instructions on programming your remote using Power Scan or
for setting up your remote to function in Limited and SAT Auto Tune modes.

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:3
posted:4/13/2012
language:
pages:4