pcs-tl30_tl33_external-control-commands

Document Sample
pcs-tl30_tl33_external-control-commands Powered By Docstoc
					                                                                                                     < PCS-TL30 External Control Command List >
                                                                                                                                  Released:2007.09.28 for PCS-TL30/TL33 Ver02.00
                                                                                                                                  Released:2007.06.29 for PCS-TL30 Ver01.30
                                                                                                                                  Released:2005.11.11 for PCS-TL30 Ver01.10

< How to use external control commands for the PCS-TL30 >

Please use either the terminal software like Windows Hyper Terminal via RS-232C(serial) port or use the telnet client like
Windows Telnet so that you can control the PCS-TL30 and check and change the setups of the PCS-TL30.

< RS-232C Specifications >

Port:                                            AUX CONTROL port at the side of PCS-TL30
Baud Rate:                                       38400 bps
Data Length:                                     8 bits
Start Bit:                                       1 bit
Stop Bit:                                        1 bit
Parity:                                          None
Flow Control:                                    None

< Telnet Specifications >

Port Number:                                     23                                                                              For taking debug logs and for External Control Command
                                                                                                                                 Only for External Control Command. No need to use "cntr" and "exit"

< How to Use Command/Return code >

- Any command requires "C/R" and "L/F" at the end of command.
- The Maximum length of each command is 250 characters.
- Some return messages are shown in multiple lines and each line has "C/R" and "L/F" codes at the end.
- PCS-1/P does not send the return code for cntr command error.

< Note >
TL30 doesn't have MCU function, so "setup save mcu" ,"setup load mcu","broadcast split","broadcast voice"command doesn't work.
(It receive response OK, but It doesn't work.)


                                                                                                             < Command/Return Code List >

0. General
                                                             [Command]                                                                                                                 [Return]
Generally used for return code except for any description in this list                                                            when command executed                           ok
                                                                                                                                  when command not executed
                                                                                                                                  when undefined command                          error syntax
                                                                                                                                  when busy state                                 error status
                                                                                                                                  when "dial" or "message" command is used        error status MOD
                                                                                                                                  and caused by stand-by mode                     (MODe: stand-by)

1. External control operation
                                                            [Command]                                                                                                                  [Return]
External operation start                         cntr
External operation end                           exit

2. Power control
                                                          [Command]                                                                                                                    [Return]
Power-on from standby and sleep mode             power-on
Go to standby mode                               stand-by
Power-on from standby and sleep mode             power-on2                                                                        when system is powered on                       power-on
Go to standby mode                               stand-by2                                                                        when system is in standby mode                  stand-by

3. Receiving a call
                                                            [Command]                                                                                                                  [Return]
Manual receiving
Reject a call                                    answer reject

4. Dial
                                                            [Command]                                                                                                                  [Return]
Call from the dial list                          dial list LNO
                                                 (ListNO: index number of receiving party 1~300)
Manual dial                                      dial /A1/ LIF LBD VID FRA AUD FEC H239
                                                 (A1: receiving party)
                                                 (LineIF: lan,sip)
                                                 (LanBanD: 1k~2048k)
                                                 (VIDeo: h263+,h261,mpeg4video,h264,video-all,video-off)
                                                 (FRAme: 15fps,30fps,auto-fps)
                                                 (AUDio: g728,g722,g711,g729,mpeg4audio,audio-all)
                                                 (FECc: fecc-on,fecc-off)
                                                 (H239: h239-on,h239-off)
                                                                                                                                  when the connection is in progress              connect status
                                                                                                                                                                                  S01 S02 S03 ... S29 S30
                                                                                                                                                                                  C01 C02 C03 ... C29 C30
                                                                                                                                                                                  (Status01~30: Status Number) *see Appendix A.
                                                                                                                                                                                  (Cause01~30: Cause Code) *see Appendix C.
                                                                                                                                  when the connection completed                   connect complete
                                                                                                                                  when the connection interrupted                 disconnect CC
                                                                                                                                                                                  (CauseCode: Cause Code) *see Appendix C.
Cancellation while calling                       dial cancel

5. Disconnect
                                                         [Command]                                                                                                                     [Return]
Disconnect all of line                           disconnect
                                                                                                                                  when disconnect all of line                     disconnect CC
                                                                                                                                                                                  (CauseCode: Cause Code) *see Appendix C.

6. Dial list
                                                            [Command]                                                                                                                  [Return]
 Register a remote party to the dial list        list save LNO /IDX/A1/ LIF LBD
(* Not available for PCS-G50/G50P)               (ListNO: index number of receiving party 1~300)
                                                 pin
                                                 (A1)
                                                 (LineIF: lan,sip)
                                                 (LanBanD: 1k~2048k)
                                                                                                                                  when registering is completed                   list save complete LNO
                                                                                                                                                                                  (ListNO: index number of receiving party 1~503)
Delete a registered entry from the dial list     list delete LNO
                                                 (ListNO: index number of receiving party 1~300)
                                                                                                                                  when deleting is completed                      list delete complete LNO
                                                                                                                                                                                  (ListNO: index number of receiving party 1~503)
Require the notice of index                      list load index
                                                                                                                                  when required the notice of index               list index
                                                                                                                                                                                  ID001
                                                                                                                                                                                  ID002
                                                                                                                                                                                  ID003
                                                                                                                                                                                  ...
                                                                                                                                                                                  ID300
                                                                                                                                                                                  (InDex001~300: index name of receiving party)

6. Dial list(continued)
                                                            [Command]                                                                                                                  [Return]
Require the contents                             list load LNO
                                                 (ListNO: index number of receiving party 1~300)
                                                                                                                                  when required the contents                      list LNO
                                                                                                                                 (* Not available for PCS-G50/G50P)               IDX
                                                                                                                                                                                  A1
                                                                                                                                                                                  LIF
                                                                                                                                                                                  LBD
                                                                                                                                                                                  (ListNO: index number of receiving party 1~300)
                                                                                                                                                                                  (InDeX: index name of receiving party)
                                                                                                                                                                                  (A1)
                                                                                                                                                                                  (LineIF:lan,sip)
                                                                                                                                                                                  (LanBanD: 1k~2048k)

8. Audio Control
                                                          [Command]                                                                                                                    [Return]
Volume control                                   audio CTL
                                                 (ConTroL: volume-up, volume-down)
                                                                                                                                  when the volume is controlled                   audio volume-VAL
                                                                                                                                                                                  (VALue: 0,1,2,3,...,23)
Switch the microphone on/off                     audio CTL

          Sony Corporation                                                                                   PCS-G70/G70P/G50/G50P External Control Command List                                                                    1/5
                                           (ConTroL: mic-on, mic-off, mic-onoff)
                                                                                                                          when the microphone is switched                 audio STS
                                                                                                                                                                          (STaTus: mic-on, mic-off)
DTMF Transmission                          audio dtmf-COD
                                           (CODe: 1,2,3,...,*,0,#)
                                                                                                                          when the DTMF transmitted                       audio dtmf-COD
                                                                                                                                                                          (CODe: 1,2,3,...,*,0,#)

9. Camera Control
                                                      [Command]                                                                                                               [Return]
Control of near end camera                 camera CTL
                                           (ConTroL: zoom-stop,zoom-tele,zoom-wide,
                                           up,down,left,right,pantilt-stop,
                                           bright-up,bright-down,bright-manual,bright-auto,
                                           backlight-on,backlight-off)
Move the near end preset position          camera move NO
                                           (NO: 1,2,3,4,5,6)
Record the near end preset position        camera save NO
                                           (NO: 1,2,3,4,5,6)
                                                                                                                          when the near end camera is controlled          camera complete
                                                                                                                          when the near end camera control is failed      camera incomplete
Control of far end camera                  far camera CTL
                                           (ConTroL: zoom-stop,zoom-tele,zoom-wide,
                                           focus-stop,focus-far,focus-near,
                                           up,down,left,right,pantilt-stop)
Move the near end preset position          far camera move NO
                                           (NO: 1,2,3,4,5,6)
Record the far end preset position         far camera save NO
                                           (NO: 1,2,3,4,5,6)

10. 4CIF(Still Image Transmission), DSB(Data Solution Box) ,White Board Control
                                                      [Command]                                                                                                               [Return]
Send the near side 4CIF image               4cif CTL
                                            (ConTroL: snap,auto,auto-stop,)
                                                                                                                          when started to send the near side 4CIFimage 4cif send-start
                                                                                                                          when completed to send the near side 4CIF image4cif send-complete
                                                                                                                          when rejected to send the near side 4CIF image 4cif send-reject
Receive the far side 4CIF image            far 4cif snap
                                                                                                                          when started to receive the far side 4CIF image 4cif receive-start
                                                                                                                                                                          4
                                                                                                                          when completed to receive the far side 4CIF image cif receive-complete
Send the near side DSB video               rgb CTL
                                           (ConTroL: start,stop)
                                                                                                                          when started to send the near side DSB video    rgb send-start
                                                                                                                          when stoped to send the near side DSB video     rgb send-stop
                                                                                                                          when rejected to send the near side DSB video   rgb send-reject


12. External MCU Control(H.243)
                                                     [Command]                                                                                                                [Return]
                                             h243
Send the MCV(requirement of broadcasting oneself) mcv
                                                                                                                          when the system is on broadcast                 h243 miv
                                                                                                                          when rejected the video                         h243 vcr
                                                                                                                          when MCV is failed                              h243 mcv incomplete
Cancel of MCV sending                      h243 cancel-mcv
                                                                                                                          when canceled the broadcast                     h243 cancel-miv
                                                                                                                          when rejected the video                         h243 vcr
                                                                                                                          when Cancel-MCV is failed                       h243 cancel-mcv incomplete

13. Internal MCU Control
                                                     [Command]                                                                                                                [Return]

14. Status(Condition)
                                                   [Command]                                                                                 [Return]
Require the notice of status               status CAT
                                           (CATegory: machine,communication,lines,audio)
                                                                                                                           when required the notice of machine status                            status machine
                                                                                                                                                                                                       MDL
                                                                                                                                                                                                       SNO
                                                                                                                                                                                                       HST
                                                                                                                                                                                                       DSP
                                                                                                                                                                                                       NAM
                                                                                                                                                                                                        IP
                                                                                                                                                                                                       MAC
                                                                                                                                                                                                       DSB
                                                                                                                                                                                                       DSV
                                                                                                                                                                                                       SIP
                                                                                                                                                                                                       LCD
                                                                                                                                                                                                       CAM
                                                                                                                                                                                                       ECX
                                                                                                                                                                                     (MoDeL: Model Name PCS-TL30)
                                                                                                                                                                                     (SerialNO.: Serial Number xxxxxx)
                                                                                                                                                                                        (HoST: HOST Version Verx.xx)
                                                                                                                                                                                          (DSP: DSP Version Verx.xx)
                                                                                                                                                                                              (NAMe: Host Name)
                                                                                                                                                                                        (IP: IP Address xxx.xxx.xxx.xxx)
                                                                                                                                                                                   (MAC: MAC Address xx-xx-xx-xx-xx-xx)
                                                                                                                                                                                  (optionDSB: optionrgb-off,optionrgb-on)
                                                                                                                                                                                    (DSbVersion: DSB Version Verx.xx)
                                                                                                                                                                                       (SIP: optionsip-off,optionsip-on)
                                                                                                                                                                                          (LCD:LCD Version Verxx.xx)
                                                                                                                                                                                      (CAM:Camera Version Verxx.xx)
                                                                                                                                                                                           (ECX:EC Version Verxx.xx)
                                                                                                                        when required the notice of communication status                 status communication MOD
                                                                                                                                                                           LID LIF NOL RAT A-T A-R V-T V-R F-T F-R T12 H28
                                                                                                                                                                              DSB WB EXT L-T L-R M-T M-R H-T H-R H239P
                                                                                                                                                                           LID LIF NOL RAT A-T A-R V-T V-R F-T F-R T12 H28
                                                                                                                                                                              DSB WB EXT L-T L-R M-T M-R H-T H-R H239P
                                                                                                                                                                           LID LIF NOL RAT A-T A-R V-T V-R F-T F-R T12 H28
                                                                                                                                                                              DSB WB EXT L-T L-R M-T M-R H-T H-R H239P
                                                                                                                                                                           LID LIF NOL RAT A-T A-R V-T V-R F-T F-R T12 H28
                                                                                                                                                                              DSB WB EXT L-T L-R M-T M-R H-T H-R H239P
                                                                                                                                                                           LID LIF NOL RAT A-T A-R V-T V-R F-T F-R T12 H28
                                                                                                                                                                              DSB WB EXT L-T L-R M-T M-R H-T H-R H239P
                                                                                                                                                                                                   (MODe: p-p)
                                                                                                                                                                                                 (LineID: 1,none)
                                                                                                                                                                                              (LineIF:lan,sip,none)
                                                                                                                                                                                                 (RATe: 0~2048)
                                                                                                                                                                         (Audio-Tx,Audio-Rx: off,g711m,g711a,g722-m1,g722-m2,
                                                                                                                                                                                    g722-m3,g728,g729,mpeg4aac,none)
                                                                                                                                                                                (Video-Tx,Video-Rx: off,h261-cif,h261-qcif,
                                                                                                                                                                                           h263-cif,h263-qcif,h263-sqcif,
                                                                                                                                                                                         h263+cif,h263+qcif,h263+sqcif,
                                                                                                                                                                                      h263++cif,h263++qcif,h263++sqcif,
                                                                                                                                                                                     mpeg4-cif,mpeg4-qcif,mpeg4-sqcif,
                                                                                                                                                                                                   h264-cif,none)
                                                                                                                                                                         (Frame-Tx,Frame-Rx: 0,30,15,7.5,6,5,4,3,2,1,50,60,none)
                                                                                                                                                                                               (H281: off,on,none)
                                                                                                                                                                                               (DSB: off,on,none)
                                                                                                                                                                                       (H239Presentation: off,on,none)

14. Status(Condition)
              [Command]                                                                                                                     [Return]
                                                                                                                          when required the notice of audio status        status audio volume-VAL MIC
                                                                                                                                                                          (VALue: 0,1,2,3,...,23)
                                                                                                                                                                          (MIC: mic-on, mic-off)
                                                                                                                                                                          (MIC: mic-on, mic-off)

15. Setup
                                                      [Command]                                                                                                               [Return]
 Save the Dial setting                     setup save dial LIF LBD VID FRA AUD FEC
(* Not available for PCS-G50/G50P)         (LineIF: lan,sip)
                                           (LanBanD: 1k~2048k)
                                           (VIDeo: h263+,h261,mpeg4video,h264,video-all,video-off)
                                           (FRAme: 15fps,30fps,auto-fps)
                                           (AUDio: g728,g722,g711,g729,mpeg4audio,audio-all)
                                           (FECc: fecc-on,fecc-off)
                                                                                                                          when saved the Dial setting                     setup save complete dial



        Sony Corporation                                                                             PCS-G70/G70P/G50/G50P External Control Command List                                                                           2/5
                                     setup save answer MOD NOB RAT LBD DID VID FRA AUD FEC DAT H239
 Save the Answer setting             MIC 4CIF INT VBI
(* Not available for PCS-G50/G50P)   (MODe: auto-on,auto-off)
                                     (LanBanD: 1k~2048k)
                                     (VIDeo: h263+,h261,mpeg4video,h264,video-all,video-off)
                                     (FRAme: 15fps,30fps,auto-fps)
                                     (AUDio: g728,g722,g711,g729,mpeg4audio,audio-all)
                                     (H239: h239-on,h239-off)
                                     (MIC: mic-on,mic-off)
                                     (VideoconferenceButtonIncome: vcbtninc-off,vcbtninc-on)
                                                                                                                       when saved the Answer setting                setup save complete answer

15. Setup(continued)
                                                [Command]                                                                                                               [Return]
Save the Audio setting               setup save audio LIP BEP EFF INC CAL
                                     (LIPsynch: lip-off,lip-on)
                                     (BEePsound: beep-on,beep-off)
                                     (EFFect: effect-on,effect-off)
                                     (INCome: income-loud,income-mid,income-min,income-off)
                                     (CALl: call-on,call-off)
                                                                                                                    when saved the Audio setting                        setup save complete audio
Save the General setting             setup save general SLP SLT TIM LNG CAM LIS /TNM/ LAT DTN TBD LAM
                                     (SLeeP: sleep-on,sleep-off)
                                     (SLeepTime: 1min~99min)
                                     (TIMe: time-on,time-off)
                                     (CAMcontrolled: camcontrolled-on,camcontrolled-off)
                                     (LIStsave: listsave-on,listsave-off)
                                     (TerminalNaMe: System Name)
                                     (LAyouT : pinp-rt, pinp-rb, pinp-lt, pinp-lb, pandp, sidebyside)              rt:Right Top, rb:Right Bottom, lb:Left Top, lb:Left Bottom
                                     (DisplayTerminalName : terminalname-on, terminalname-off, terminalname-temporaryon)
                                     (TaskBarDisplay : taskbar-on, taskbar-off)
                                     (LAuncherMode: launcher-normal,launcher-kiosk,launcher-skeleton)
                                     (BAckGround: background-1,background-2,background-3,background-4)
                                                                                                                    when saved the General setting                      setup save complete general

15. Setup(continued)
                                                [Command]                                                                                                               [Return]
                                     setup save lan DHC SNM MOD TOS LOW HIT HIR MIN PPP PFI PDN
                                     /HOS/IP/NET/GTW/DNS/TRP/COM/DSC/LOC/CTC/IPP/DIF/PUS/PPW/PIP/PD1
Save the LAN setting                 /PD2/
                                     (DHCp: dhcp-off,dhcp-auto)
                                     (SNmp Mode: snmp-off,snmp-on)
                                     (lan MODe: mode-auto,mode-100f,mode-100h,mode-10f,mode-10h)
                                     (TOS: tos-off,tos-ipprecedence,tos-diffserve)
                                     (LOW delay: lowdelay-off,lowdelay-on)
                                     (HIgh Throughput: highthroughput-off,highthroughput-on)
                                     (HIgh Reliability: highreliability-off,highreliability-on)
                                     (MINimum cost: minimumcost-off,minimumcost-on)
                                     (PPPoe: pppoe-off,pppoe-on)
                                     (Pppoe Fixed Ip: pppoefixedip-off,pppoefixedip-on)
                                     (Pppoe DNs: pppoedns-off,pppoedns-on)
                                     (HOSt: Host Name)
                                     (IP: IP Address)
                                     (NETmask: Net Mask)
                                     (GaTeWay: Gateway Address)
                                     (DNS: DNS Address)
                                     (TRaP: Trap Address)
                                     (COMmunity: Community Name)
                                     (DeSCription: System Description)
                                     (LOCation: System Location)
                                     (ConTaCt: System Contact)
                                     (IP Precedence: IP Precedence Value [0-7])
                                     (DIFfserve: Diffserve Value [0-63])
                                     (Pppoe USer: PPPoE User)
                                     (Pppoe PassWord: PPPoE Passwd)
                                     (Pppoe IP: PPPoE IP Address)
                                     (Pppoe Dns1: PPPoE Primary DNS IP Address)
                                     (Pppoe Dns2: PPPoE Secondary DNS IP Address)
                                                                                                                       when saved the LAN setting                   setup save complete lan
                                                                                                                       when succeeded the LAN setting               setup lan ST CC
                                                                                                                                                                    (STate: 0:succeeded 1:failed)
                                                                                                                                                                    (CauseCode: LAN Cause Code) *see Appendix D.
                                     setup save SET TOS LOW HIT HIR MIN /IPP/DIF/
                                     (SETting: lan-tosvideo,lan-tosaudio,lan-tospresen,lan-toscamera)
                                     (TOS: tos-off,tos-ipprecedence,tos-diffserve)
                                     (LOW delay: lowdelay-off,lowdelay-on)
                                     (HIgh Throughput: highthroughput-off,highthroughput-on)
                                     (HIgh Reliability: highreliability-off,highreliability-on)
                                     (MINimum cost: minimumcost-off,minimumcost-on)
                                     (IP Precedence: IP Precedence Value [0-7])
                                     (DIFfserve: Diffserve Value [0-63])
                                                                                                                       when saved the LAN setting                   setup save complete lan
                                                                                                                       when succeeded the LAN setting               setup lan ST CC
                                                                                                                                                                    (STate: 0:succeeded 1:failed)
                                                                                                                                                                    (CauseCode: LAN Cause Code) *see Appendix D.
                                     setup save h323 GMD NAM ARQ RTCP PORT
Save the H.323 setting               /GKP/ALS/NUM/NAT/TCP/UDP/NFT/
                                     (Gatekeeper MoDe: gk-off,gk-on,gk-auto)
                                     (Nat Mode: nat-off,nat-on)
                                     (ARQ mode: arq-off,arq-on)
                                     (RTCP mode: rtcp-off,rtcp-on)
                                     (PORT mode: fixedport-off,fixedport-on)
                                     (GateKeePer: Gatekeeper Address)
                                     (ALiaS: H.323 Alias)
                                     (NUMber: E.164 Number)
                                     (NAT: NAT Address)
                                     (TCP: TCP Port Address)
                                     (UDP: UDP Port Address)
                                     (NatFirewallTraversal : h460-off, h460-on)
                                                                                                                       when saved the H.323 setting                 setup save complete h323
Save the SIP setting                 setup save sip MODE TPR /SDN/PORT/
                                     (MODE: sip-off,sip-on)
                                     (Transport PRotocol: protocol-udp,protocol-tcp)
                                     (Sip Domain Name: Sip Domain Name)
                                     (PORT: Sip Port Number)
                                                                                                                       when saved the SIP setting                   setup save complete sip
Save the SIP (Server) setting        setup save SET /PRO/REG/P-PORT/R-PORT/
                                     (SETting: sip-server1,sip-server2,sip-server3,sip-server4)
                                     (PROxy: Proxy Server Name)
                                     (REGistra: Registra Server Name)
                                     (Proxy PORT: Proxy Server Port Number)
                                     (Registra PORT: Registra Server Port Number)
                                                                                                                       when saved the SIP setting                   setup save complete sip
Save the SIP (User) setting          setup save SET /NAME/PASS/
                                     (SETting: sip-user1)
                                     (NAME: User Name)
                                     (PASSword: User Password)
                                                                                                                       when saved the SIP setting                   setup save complete sip
Require the notice of contents       setup load CAT
                                     (CATegory: dial,answer,audio,general,lan,h323,sip,video)

                                                                                                                       when required the state of Dial setting      setup dial
                                                                                                                      (* Not available for PCS-G50/G50P)            LIF
                                                                                                                                                                    LBD
                                                                                                                                                                    VID
                                                                                                                                                                    FRA
                                                                                                                                                                    AUD
                                                                                                                                                                    FEC

15. Setup(continued)
                                               [Command]                                                                                                                [Return]
                                                                                                                                                                    (LineIF: bri,speech,lan,sip)
                                                                                                                                                                    (LanBanD: 1k~2048k)
                                                                                                                                                                    (VIDeo: h263+,h261,mpeg4video,h264,video-all,video-off)
                                                                                                                                                                    (FRAme: 15fps,30fps,auto-fps)
                                                                                                                                                                    (AUDio: g728,g722,g711,g729,mpeg4audio,audio-all)
                                                                                                                                                                    (FECc: fecc-on,fecc-off)
                                                                                                                       when required the state of Answer setting    setup answer
                                                                                                                      (* Not available for PCS-G50/G50P)            MOD
                                                                                                                                                                    LBD
                                                                                                                                                                    VID

        Sony Corporation                                                                          PCS-G70/G70P/G50/G50P External Control Command List                                                                         3/5
                                                                                                        FRA
                                                                                                        AUD
                                                                                                        H239
                                                                                                        MIC
                                                                                                        VBI
                                                                                                        (MODe: auto-on,auto-off)
                                                                                                        (LanBanD: 1k~2048k)
                                                                                                        (VIDeo: h263+,h261,mpeg4video,h264,video-all,video-off)
                                                                                                        (FRAme: 15fps,30fps,auto-fps)
                                                                                                        (AUDio: g728,g722,g711,g729,mpeg4audio,audio-all)
                                                                                                        (H239: h239-on,h239-off)
                                                                                                        (MIC: mic-on,mic-off)
                                                                                                        (VideoconferenceButtonIncome: vcbtninc-off,vcbtninc-on)

15. Setup(continued)
                          [Command]                                                                         [Return]
                                                           when required the state of Audio setting     setup audio
                                                                                                        LIP
                                                                                                        BEP
                                                                                                        EFF
                                                                                                        INC
                                                                                                        CAL
                                                                                                        (LIPsynch: lip-off,lip-on)
                                                                                                        (BEePsound: beep-on,beep-off)
                                                                                                        (EFFect: effect-on,effect-off)
                                                                                                        (INCome: income-loud,income-mid,income-min,income-off)
                                                                                                        (CALl: call-on,call-off)
                                                           when required the state of General setting   setup general
                                                                                                        SLP
                                                                                                        SLT
                                                                                                        TIM
                                                                                                        LNG
                                                                                                        CAM
                                                                                                        LIS
                                                                                                        TNM
                                                                                                        LAM
                                                                                                        BAG
                                                                                                        (SLeeP: sleep-on,sleep-off)
                                                                                                        (SLeepTime: 1min~99min)
                                                                                                        (TIMe: time-on,time-off)
                                                                                                        (LaNGuage:
                                                                                                        english,french,german,italian,japanese,spanish,portuguese,simplifi
                                                                                                        ed-chinese)
                                                                                                        (CAMcontrolled: camcontrolled-on,camcontrolled-off)
                                                                                                        (LIStsave: listsave-on,listsave-off)
                                                                                                        (TerminalNaMe: System Name)
                                                                                                        (LAuncherMode: launcher-normal,launcher-kiosk,launcher-skeleton)
                                                                                                        (BAckGround: background-1,background-2,background-3,background-4)

15. Setup(continued)
                          [Command]                                                                          [Return]
                                                           when required LAN setting                    setup lan
                                                                                                        DHC
                                                                                                        SNM
                                                                                                        HOS
                                                                                                        IP
                                                                                                        NET
                                                                                                        GTW
                                                                                                        DNS
                                                                                                        TRP
                                                                                                        COM
                                                                                                        DSC
                                                                                                        LOC
                                                                                                        CTC
                                                                                                        MOD
                                                                                                        TOS-V
                                                                                                        IPP-V
                                                                                                        LOW-V
                                                                                                        HIT-V
                                                                                                        HIR-V
                                                                                                        MIN-V
                                                                                                        DIF-V
                                                                                                        PPP
                                                                                                        PUS
                                                                                                        PPW
                                                                                                        PFI
                                                                                                        PIP
                                                                                                        PDN
                                                                                                        PD1
                                                                                                        PD2
                                                                                                        TOS-A
                                                                                                        IPP-A
                                                                                                        LOW-A
                                                                                                        HIT-A
                                                                                                        HIR-A
                                                                                                        MIN-A
                                                                                                        DIF-A
                                                                                                        TOS-P
                                                                                                        IPP-P
                                                                                                        LOW-P
                                                                                                        HIT-P
                                                                                                        HIR-P
                                                                                                        MIN-P
                                                                                                        DIF-P
                                                                                                        TOS-C
                                                                                                        IPP-C
                                                                                                        LOW-C
                                                                                                        HIT-C
                                                                                                        HIR-C
                                                                                                        MIN-C
                                                                                                        DIF-C
                                                                                                        (DHCp: dhcp-off,dhcp-auto)
                                                                                                        (SNmp Mode: snmp-off,snmp-on)
                                                                                                        (HOSt: Host Name)
                                                                                                        (IP: IP Address)
                                                                                                        (NETmask: Net Mask)
                                                                                                        (GaTeWay: Gateway Address)
                                                                                                        (DNS: DNS Address)
                                                                                                        (TRaP: Trap Address)
                                                                                                        (COMmunity: Community Name)
                                                                                                        (DeSCription: System Description)
                                                                                                        (LOCation: System Location)
                                                                                                        (ConTaCt: System Contact)
                                                                                                        (lan MODe: mode-auto,mode-100f,mode-100h,mode-10f,mode-10h)
                                                                                                        (TOS : tos-off,tos-ipprecedence,tos-diffserve)
                                                                                                        (IP Precedence : IP Precedence Value [0-7])
                                                                                                        (LOW delay : lowdelay-off,lowdelay-on)
                                                                                                        (HIgh Throughput : highthroughput-off,highthroughput-on)
                                                                                                        (HIgh Reliability : highreliability-off,highreliability-on)
                                                                                                        (MINimum cost : minimumcost-off,minimumcost-on)
                                                                                                        (DIFfserve Video,Audio,Presentation,Camera control: Diffserve
                                                                                                        Value [0-63])
                                                                                                        (PPPoe: pppoe-off,pppoe-on)
                                                                                                        (Pppoe USer: PPPoE User)
                                                                                                        (Pppoe PassWord: PPPoE Passwd)
                                                                                                        (Pppoe Fixed Ip: pppoefixedip-off,pppoefixedip-on)
                                                                                                        (Pppoe IP: PPPoE IP Address)
                                                                                                        (Pppoe DNs: pppoedns-off,pppoedns-on)
                                                                                                        (Pppoe Dns1: PPPoE Primary DNS IP Address)
                                                                                                        (Pppoe Dns2: PPPoE Secondary DNS IP Address)

15. Setup(continued)
                          [Command]                                                                         [Return]
                                                           when required H.323 setting                  setup h323
                                                                                                        GMD
                                                                                                        NAM
                                                                                                        ARQ
                                                                                                        RTCP
                                                                                                        PORT
                                                                                                        GKP
       Sony Corporation               PCS-G70/G70P/G50/G50P External Control Command List                                                                                    4/5
                                                                                                                                                                   ALS
                                                                                                                                                                   NUM
                                                                                                                                                                   NAT
                                                                                                                                                                   TCP
                                                                                                                                                                   UDP
                                                                                                                                                                   (Gatekeeper MoDe: gk-off,gk-on,gk-auto)
                                                                                                                                                                   (Nat Mode: nat-off,nat-on)
                                                                                                                                                                   (ARQ mode: arq-off,arq-on)
                                                                                                                                                                   (RTCP mode: rtcp-off,rtcp-on)
                                                                                                                                                                   (PORT mode: fixedport-off,fixedport-on)
                                                                                                                                                                   (GateKeePer: Gatekeeper Address)
                                                                                                                                                                   (ALiaS: H.323 Alias)
                                                                                                                                                                   (NUMber: E.164 Number)
                                                                                                                                                                   (NAT: NAT Address)
                                                                                                                                                                   (TCP: TCP Port Address)
                                                                                                                                                                   (UDP: UDP Port Address)
                                                                                                                                     when required sip setting     setup sip
                                                                                                                                                                   MODE
                                                                                                                                                                   TPR
                                                                                                                                                                   SDN
                                                                                                                                                                   PORT
                                                                                                                                                                   PRO-1
                                                                                                                                                                   REG-1
                                                                                                                                                                   P-PORT-1
                                                                                                                                                                   R-PORT-1
                                                                                                                                                                   PRO-2
                                                                                                                                                                   REG-2
                                                                                                                                                                   P-PORT-2
                                                                                                                                                                   R-PORT-2
                                                                                                                                                                   PRO-3
                                                                                                                                                                   REG-3
                                                                                                                                                                   P-PORT-3
                                                                                                                                                                   R-PORT-3
                                                                                                                                                                   PRO-4
                                                                                                                                                                   REG-4
                                                                                                                                                                   P-PORT-4
                                                                                                                                                                   R-PORT-4
                                                                                                                                                                   NAME-1
                                                                                                                                                                   PASS-1
                                                                                                                                                                   (MODE: sip-off,sip-on)
                                                                                                                                                                   (Transport PRotocol: protocol-udp,protocol-tcp)
                                                                                                                                                                   (Sip Domain Name: Sip Domain Name)
                                                                                                                                                                   (PORT: Sip Port Number)
                                                                                                                                                                   (PROxy-1~4: Proxy Server Name 1~4)
                                                                                                                                                                   (REGistra-1~4: Registra Server Name 1~4)
                                                                                                                                                                   (Proxy PORT-1~4: Proxy Server Port Number 1~4)
                                                                                                                                                                   (Registra PORT-1~4: Registra Server Port Number 1~4)
                                                                                                                                                                   (NAME-1: User Name 1)
                                                                                                                                                                   (PASSword-1: User Password 1)
Set time                                          time /MM-DD-YYYY/HH:MM:SS/
                                                                                                                                     when required time setting    time complete
Check time                                        time
                                                                                                                                     when required time checking   time MM-DD-YYYY HH:MM:SS

16. Simulate Remote Commandar
                                                            [Command]                                                                                                  [Return]

                                                                                             < Appendix : Status Number, Cause Code and Country ID >


A. Status Number when the connection is in progress
                                         0 not available(no option card fitted)
                                         1 network detected but no call in progress
                                         2 call in progress
                                         3 connected
                                         4 call failed

B. Status Number of Line Status
                                             0    not available(no option card fitted)
                                             1    no network(option card fitted but no network detected)
                                             2    network detected but no call in progress
                                             3    call in progress
                                             4    connected
                                             5    call failed

C. Cause Code
                                              0   Unknown network error: Try again later.
                                              1   Number does not exist: Check the number and try again.
                                          2,3,6   Network congestion: Try again later.
                                            16    Normal disconnection: (The line has been disconnected normally.)
                                            17    Line is busy: Try again later.
                                            18    System not responding: Check if the remote system is connected.
                                            19    System not responding: Check if the remote system is connected.
                                            21    Call rejected: Check if the remote system is connected.
                                            22    Called party number changed: Check the number and try again.
                                            26    Connection restoration request: Try again later.
                                            27    Remote system out of order: Check if the remote system is operational.
                                            28    Invalid number entered: Check the number and try again.
                          31,34,41,42,43,44,47    Network not available: Try again later.
                                            50    Not a Subscriber: Check the remote party's facility contract.
                                         57,58    Bearer capability not authorized: Check if the line rate is set correctly.
                                            70    Restricted capability: Set the line rate to 56K and try again.
                                            88    Terminal attribute error: Check the connection of the remote system.
                                91,95-102,111     Protocol error: Turn off and restart the system and try again.
                                           128    H.221 negotiation timeout: Turn off and restart the system and try again.
                                           131    Board mismatch: Check the optional line interface boards.
                                           132    Invalid SPID: Reregister the SPID.
                                           134    Physical link synchronization error: Check the connection of the ISDN cable.
                                      144,145     Bonding negotiation timeout: Turn off and restart the system and try again.
                                           177    LAN connection timeout: Try again later.
                                           178    LAN connection rejected: Try again later.
                                           179    DNS error.
                                           180    Dialing your own number is invalid.
                                           181    GateKeeper error.

D. Cause Code of LAN Setup
                                             1    LAN Setup Error (IP Address)
                                             2    LAN Setup Error (Net Mask)
                                             3    LAN Setup Error (MAC Address)
                                             4    LAN Setup Error (DHCP Error)
                                             5    LAN Setup Error (Gatekeeper)
                                             6    LAN Setup Error (SNMP Error)

E. Country ID of ISDN Setup

17.POPUP Control
popup ok or cancel                                popup-ok
                                                  popup-cancel

18.Display Control
display vc mode or pc mode                        display vc
                                                  display pc
push menu button                                  dispmenu
display Select vc or pc                           dispsel vc
                                                  dispsel pc
Current display mode confirmation                 status pcvc                                                                                                      pc or vc

 19.Message Control
smessage /Message.../Position/Time/               Position : 0(upper), 1(middle), 2(low)
                                                  Time : 1 - 256 (sec), 0(endless), -1(delete)
                                                   ex. smessage /hello/0/5 [display "hello" message on upper layer for 5 seconds.]
                                                   ex. smessage ///-1/ [delete message]




           Sony Corporation                                                                                 PCS-G70/G70P/G50/G50P External Control Command List                                                           5/5

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:3
posted:4/5/2012
language:English
pages:5