Docstoc

Newton Waterproofing Systems

Document Sample
Newton Waterproofing Systems Powered By Docstoc
					                                                      Cl/SfB
                                                                Ln6 (L34)

                                              © John Newton & Co. Ltd.
                                                Issue Date: February 2012




      Protecting buildings, since 1848




NEWTON WATERPROOFING SYSTEMS
                               Product Catalogue
                                    100 - Cementitious Products
                                           200 - Deck And Roofing
                   300 - Waterproofing of Concrete Structures
                                    400 - External Waterproofing
                               500 - Cavity Drain Waterproofing
                                         600 - Flooring Membranes
                            700 - Liquid Applied Floor Coatings
                                              800 - Damp Proofing
                                 900 - Liquid Primers & Sealers
                   FlexProof Construction Joint Waterproofing
                                    Diathonite Insulating Plaster
                                                  Sump and Pump
                                                               Multi-Use
PRODUCT CATALOGUE
SYSTEM 100 - CEMENTITIOUS PRODUCTS                        SYSTEM 300 - WATERPROOFING OF
Newton System 100 is a comprehensive portfolio            CONCRETE STRUCTURES
of cementitious products which have been                  Newton System 300 is a range of products, some
introduced into our structural waterproofing range        unique to John Newton, used to waterproof con-
to complement and complete our basement                   struction joints and movement joints of retained
waterproofing designs in areas where the Newton           concrete structures so that they become integrally
System 500 would not be suitable. Such details            waterproof without the need of additional water-
include - lift shafts, flat soffits and externally to     proofing products, defined within BS8102:2009 as
retained slabs and ring beams.                            Type B waterproofing.
Newton 101 F (CW 101), Page 4                             Newton 301 AquaProof, Page 11
Cementitious Flexible Waterproofing Membrane              Metal Construction Joint Water Bar
Newton 102 WaterPlug (CW 102), Page 5                     Newton 302 InjectionHose, Page 11
Fast Setting Polymer Compound To Seal Leaks               Maintainable Injection Water Bar System
Newton 103 SBR (CW 103), Page 5                           Newton 303 PolyProof, Page 12
Waterproof Additive                                       High Grade Hydrophilic Water Bar
Newton 106 Lime Inhibitor (LC1), Page 5                   Newton 304 PolyProof Inject, Page 12
Lime Inhibitor for Application to Concrete Surfaces       High Grade Hydrophilic Water Bar
Newton 107 QuickFillet (CW 107), Page 6                   Newton 305 ActiveJoint, Page 12
Fast Setting Pre-Mix Mortar for Angle Fillets             Physical Movement Joint Water Bar
                                                          Newton 306 SwellMastic, Page 13
SYSTEM 200 - DECK & ROOFING                               Swelling Adhesive
A complete range of externally applied elastomeric        Newton 307 PipeSeal, Page 13
high performance liquid membranes and ancillaries         Pipe Collar
for balconies, terraces, flat and inverted roofs,
podium decks, car parks and reservoirs. This new          Newton 308 Stopaq (SX 108), Page 13
portfolio of seamless and robust liquid membranes         Unique Hydrophilic Polymer Sealant
gives specifiers and specialist waterproofing
contractors a quick and cost effective solution to        SYSTEM 400 - EXTERNAL WATERPROOFING
protect external areas from water ingress.                System 400 is a range of products for the
                                                          waterproofing of the outside of earth retained
Newton RubberFlex System, Page 7                          structures. Products include sheet membranes for
Podium Deck and Flat Roof Waterproofing System            the complete envelopment of the raft and walls,
                                                          flexible liquid products for the waterproofing of
Newton 204 Thinner (RF 204), Page 8                       retained walls and composite drainage membranes
Polyurethane Thinning & Cleaning Agent                    for preventing the build up of ground water to the
Newton 205 ColorSeal (LM 205), Page 8                     walls or below the raft. Newton System 400 products
UV Colour Stable Polyurethane Coating                     can provide Type A and Type B waterproofing to
Newton 207 DeckDrain (M30), Page 9                        Grades 2 & 3 as defined within BS8102:2009
Drainage Membrane for Decks and Flat Roofs                Newton 401 FlexProof-X1, Page 14
Newton 209 Root Barrier (M32), Page 9                     Flexible Membrane for Retaining Walls
Puncture Resistant Root Barrier Membrane                  Newton 402 Aquabit, Page 15
Newton 210 FlexProof-NV (FP4), Page 10                    Flexible Membrane for Retaining Walls
Waterproofing of Podium Decks and Flat Roofs              Newton 403 HydroBond, Page 15
Newton 220 Reservoir (M31), Page 10                       Hydrophilic and Bonding Membrane for Raft and
Extensive Green Roof Drainage Membrane                    Wall Waterproofing
                                                          Newton 410 Geodrain, Page 16
                                                          Externally Applied Drainage Membrane



Note: Please check individual product sheets for advice on appropriate fixings and ancillary products. Contact our Technical
Department for further information on 020 7237 1217. Copies of our BBA Certificates, Brochures and Data Sheets can be
downloaded from www.newton-membranes.co.uk. Products and their specifications can be changed or modified without
prior notice. All copy, diagrams, images and Newton trade names/logos and designs used in this catalogue remain the
intellectual property of John Newton and Company Ltd. and may not be reproduced without the written permission of the
Directors of John Newton and Company Ltd. Any party who exploits this property may be subject to prosecution.

          © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
                  www.newton-membranes.co.uk - info@newton-membranes.co.uk
PRODUCT CATALOGUE
SYSTEM 500 - CAVITY DRAIN WATERPROOFING                SYSTEM 800 - DAMP PROOFING
The professional’s “waterproofing system of            Newton System 800 is a range of BBA approved
choice”, Newton System 500 is an internally            damp proof membranes and ancillaries which are
applied waterproofing system based upon our range      quick and clean to install and offer a permanent
of cavity drain membranes, drainage conduits and       solution for damp proofing walls. The meshed
sophisticated pumping and control systems. Unlike      membranes provide a firm key and impermeable
conventional ‘tanking’, Newton System 500 is not       barrier on any damp or deteriorating surface ready
attempting the almost impossible and trying to         for plaster, render or dot & dab plasterboard. The
hold water back, but places designed maintainable      un-meshed Newton 803 is used where insulation
depressurisation voids at known weaknesses in          requirements dictate the use of a timber or steel
the structure so that ingressing water is simply       frame ready for plasterboard. Quick, clean and
captured and diverted out of the property.             proven to work, Newton damp proof membranes
                                                       offer a permanent and cost effective damp
Wall Membranes                                         proofing solution.
Newton 503 (M5), Page 17
                                                       Damp Proofing Membranes
Newton 503 Mesh (M11 & M12), Page 17
                                                       Newton 805 Newlath (M9 & M10), Page 22
Newton 508 (M1 & M2), Page 18
                                                       Newton 803 (M19 & M20), Page 23
Newton 508 Mesh (M3), Page 18
                                                       Newton 803 Newtonite (M16, M21, M22), Page 23
Newton 520 (M4 & M13), Page 18
                                                       Newton 801 FlexProof-X1 Wet Room Waterproofing,
Drainage System                                        Page 23
Newton Basedrain (D1), Page 18                         Damp Proofing Ancillaries
                                                       Newton 800 Mesh Plug (A16), Page 24
SYSTEM 600 - FLOORING MEMBRANES                        Newton MultiPlug (A1), Page 24
Newton System 600 is a range of HDPE and
                                                       Newton 800 Cob Plug (A17), Page 24
HDPP flooring membranes offering a complete
damp proof solution for both commercial and            Newton 800 Newtonite Plugs (A20), Page 24
domestic flooring applications. As well as             Newton 800 Mastic (A18), Page 25
providing protection from dampness within the          Newton Mesh Tape (A25), Page 25
floor, our membranes ‘de-couple’ the floor finish      Newton Overtape (A8), Page 25
from the substrate preventing damage due to
substrate movement and cracking. Newton damp           Newton 800 Profile (A19), Page 25
proof membranes can be installed over existing
and ‘green’ concrete. In addition, our flooring        SYSTEM 900 - LIQUID PRIMERS & SEALERS
membranes are a popular solution for dealing with
                                                       Newton’s high performance range of liquid applied
inherent hydrocarbons or ground gas problems.
                                                       products are used in conjunction with System 200
Newton flooring membranes can accommodate a
                                                       and 700 liquid membranes. They act as priming
variety of finishes including timber floors, screeds
                                                       agents for a variety of substrates prior to the
and direct tiles.
                                                       application of our specialist waterproofing and
Flooring Membranes                                     flooring membranes.
Newton 601 Slimline (M6), Page 19                      Newton 901 Humidity Primer (PS 901), Page 26
Newton 603 (M23), Page 19                              Epoxy Primer Suitable for High Humidity Substrate
Newton 603 Mesh (M24 & M25), Page 20                   Newton 902 (PS 902), Page 26
                                                       Liquid Applied Radon, Gas & Vapour Barrier
SYSTEM 700 - LIQUID APPLIED FLOOR COATINGS             Newton 903 PU Primer (PS 903), Page 27
System 700 is a range of liquid applied protective     Epoxy Primer for Nonporous Substrate
and decorative internal flooring products. These
                                                       Newton 904 HP Accelerant (PS 904), Page 27
products are fast curing and available in a
variety of colours, and are typically used for the     Humidity Primer Accelerant
refurbishment and protection of commercial and         Newton 906 Mould Stop (PS 906), Page 27
domestic floors.                                       Mould Steriliser & Killer
Newton 701 HB (LM 701), Page 21
High Build Epoxy Floor Coating
Newton 702 EcoSeal (LM 702), Page 21
Highly Resistant Polyurethane Floor Coating

          © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
                 www.newton-membranes.co.uk - info@newton-membranes.co.uk
PRODUCT CATALOGUE
NEWTON FLEXPROOF - CONSTRUCTION                        SUMP AND PUMP
JOINT WATERPROOFING                                    Newtons have an extensive range of submersible
Newton FlexProof-X1 forms an elastomeric polymer       pumps and pumping ancillaries. We supply the
membrane that is rainproof in minutes and              highest quality pumps available in each class,
capable of handling severe building movements          for the control of clean ground water, grey water,
and deformations. FlexProof-X1 is quite unique         effluent or sewage.
with amazing characteristics allowing it to be used
without a primer, without mixing and in weather        Clean/Ground Water Pumps
conditions that preclude the use of alternatives.      Newton NP150 (P1), Page 30
                                                       Newton CP250 (P31), Page 30
Newton FlexProof-X1 (FP1), Page 28                     Newton CP400 (P32), Page 31
Construction Joint Waterproofing                       Newton NP400 (P2 & P3), Page 31
                                                       Newton NP400PP (P13), Page 31
                                                       Newton NP400LLPS (SP1), Page 31
NEWTON DIATHONITE - INSULATING PLASTER                 Newton CP750 (P33), Page 32
Newton Diathonite is a premixed plaster, fibre-        Newton NP750 (P5 & P6), Page 32
reinforced with cork (granular 0-3 mm), clay
                                                       Effluent Pumps (Not Sewage)
powders and NHL 3.5 natural hydraulic lime.
The resulting natural compound produces a plaster      Newton NP400W (P4), Page 32
with unrivalled thermal and acoustic properties that   Sewage Pumps
is both hard wearing and flexible which is ideal for
                                                       Newton SP750 Ranger (P9), Page 33
both internal and external applications. .
                                                       Newton Flygt DXG (Grinder) (P14 & P16) Page 33
Newton Diathonite, Page 29
                                                       Sewage Lifting Station
Eco Thermal Plaster with Insulation and Acoustic
                                                       Trojan Sewage Pumping System (TR1-TR12), Page 33
Properties
                                                       Clean/Ground/Effluent Pumping Systems
                                                       Titan-Pro White (TPW), Page 34
                                                       Titan-Pro Green (TPG), Page 34
                                                       Newton Titan-2 (T1-T10), Page 34
                                                       Pumping Ancillary Products
                                                       Newton Control Panel Pro (CP2), Page 35
                                                       Newton High Water Level Alarm (PA50), Page 35
                                                       Newton Dialer (PA5, PA6, PA7), Page 35
                                                       Newton 1200w Power Converter (C1 & C3), Page 36
                                                       Newton 3000w Power Converter (C2 & C4), Page 36

                                                       Newtons can also provide a wide range of specialist
                                                       submersible pumps and sump chambers which
                                                       can be tailor made for site-specific conditions. For
                                                       further information call our technical department
                                                       on 020 7237 1217

                                                       MULTI-USE
                                                       The Multi-Use section is home to products that
                                                       are used within more than one of our systems.
                                                       WaterSeal Tape, for example, can be used with
                                                       System 300, System 400, System 500, System 600
                                                       and System 800.
                                                       Newton Mesh Tape (A25), Page 37
                                                       Newton Overtape (A7, A8, A9), Page 37
                                                       Newton WaterSeal Rope (A6 & A6W), Page 37
                                                       Newton WaterSeal Tape (A5 & A5W), Page 38
                                                       Newton MultiPlug (A1), Page 38
                                                       Newton NuSeal Plugs (A2 & A3), Page 38



         © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
                www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 100
            Cementitious Products


            NEWTON SYSTEM 100 - CEMENTITIOUS PRODUCTS
            System Overview
            Newton System 100 is a comprehensive portfolio of Type A
            (BS8102:2009) cementitious waterproofing products for the sealing of
            leaks and the waterproofing of lift shafts, flat soffits, walls and slabs.
            System 100 products can be used on their own, or in conjunction with
            System 200, System 300, System 400 and System 500 waterproofing
            products, and with System 700 (Liquid Flooring Membrane) and System
            800 (damp-proofing) products also.




            NEWTON 101F (CW 101)
            Cementitious Flexible Waterproofing Membrane
             Newton 101F is a two-component acrylic modified cementitious coating.
             It is the ideal product to waterproof and re-surface concrete and masonry.
             101F is a hard wearing, seamless waterproofing solution which is very
             user friendly with simple on-site mixing methods.
             Newton 101F is applied in two coats 1mm each to provide a total
             thickness of 2mm. Each 1mm coat requires a coverage rate of
             1.8kg per m² to give a total coverage rate of 3.6kg per m². Newton 101F
             is supplied in two components of 1 x 25kg tub of powder and 10kg of
             liquid additive (35kg pack) which will cover 9m² - 10m²
             Typical Applications:
            •      Waterproof lining for lift pits, swimming pools etc
            •      Bathroom and wet areas
            •      Waterproof coating for roofs
            •      Internal application to flat concrete soffits in conjunction with
                   Newton System 500
            •      Slurry application to form waterproof bunds
            •      Lining existing concrete sump chambers
            •      Protection of steels against carbonation and chloride attacks




            Page 4

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 100
            Cementitious Products


            NEWTON 102 WATERPLUG (CW 102)
            Fast Setting Polymer Compound To Seal Leaks
             Newton 102 WaterPlug is a fast setting, polymer compound that instantly
             stops running water or seepage through masonry or concrete substrates.
             It becomes harder and more resistant when subjected to constant water
             pressure. Newton 102 WaterPlug is a non-shrink material that expands
             slightly and sets in approximate 2 minutes. Available in 5kg, 10kg or
             25kg tubs.
             Typical Applications:
            •      Leak sealing prior to tanking with Newton 101F
            •      Sealing of leaks at wall/floor junctions
            •      Sealing of leaking mortar joints
            •      Leak sealing of cracks in masonry or concrete
            •      Repair of construction faults such as honeycombing
            •      Anchoring of bolts or posts
            •      Controlling water ingress during sump installations


            NEWTON 103 SBR (CW 103)
            Waterproof Additive
            Newton 103 SBR is a high quality liquid, water-based high solids
            styrene butadiene polymer latex with high bonding and waterproofing
            characteristics. It is stable under wet alkaline conditions forming a
            reinforcing polymer matrix within cementitious mixes. Available in 5kg,
            10kg and 25kg
             Typical Applications:
            •     Surface waterproofing                                    •     Lift shafts
            •     Waterproof screeds                                       •     Wall/floor junction fillets



            NEWTON 106 LIME INHIBITOR (LC1)
            Lime Inhibitor For Application To Concrete Surfaces
            Newton 106 Lime Inhibitor is applied to concrete surfaces prior to the
            installation of a Newton System 500 cavity drain membrane waterproofing
            system to prevent the ‘leaching’ of free lime from the concrete. Primarily
            designed to be used to new concrete structures, Newton Lime Inhibitor
            should also be used to treat the following areas: newly formed concrete
            walls, kickers and underpins, treatment to cut recesses prior to Basedrain
            installation and as a concrete additive to newly formed sump chambers.
            Supplied in 1kg units - Newton 106 is a concentrated mix to be added
            1 part Newton 106 Lime Inhibitor to 9 parts clean water. Newton 106
            should be applied in this 10 litre mix through a course sprayer and will
            cover a maximum of 100 sq m²
            Product Features:
            •     Solvent and caustic free                                 •     Easy to use and handle
            •     Non-hazardous (on dilution)                              •     Long term durability
            •     Compatible with alkaline substrates                                                                                          Page 5

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 100
            Cementitious Products



            NEWTON 107 QUICKFILLET (CW 107)
            Fast Setting Pre-Mix Mortar For Angle Fillets
            Newton 107 QuickFillet is a fast setting and fast curing mortar with a
            rapid strength gain used to quickly form 45° angled fillets at junctions
            between walls and floors or soffits. Newton 107 QuickFillet should be
            used to form fillets for use with Newton 101F cementitious slurry and
            can be used to reinforce internal corners ready for Newton liquid applied
            membranes such as 201 RubberFlex, 205 ColorSeal or 702 EcoSeal.
            Newton 107 Quick Fillet can also be used to repair substrate prior to the
            use of Newton System 900 primers.
            Newton 107 QuickFillet is supplied in 25kg tubs and when correctly mixed
            with 3.6 litres of clean water should cover approx 30 linear metres applied
            in a 25mm x 25mm fillet
            Typical Applications:
            •     Creation of angle fillets
            •     Surface repairs to substrate prior to application of Newton System
                  900 floor primers




            Page 6

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 200
            Deck & Roofing


            NEWTON SYSTEM 200 - DECK AND ROOFING
            System Overview
            Newton System 200 is a complete range of externally applied liquid
            elastomeric membranes for the structural waterproofing of podium decks,
            balconies and terraces, flat and inverted roofs, car parks, swimming
            pools, green or turf roofs and reservoirs. This new portfolio of seamless
            and robust liquid membranes gives specifiers and specialist waterproofing
            contractors a quick and cost effective solution to protect external areas
            from water ingress.



            NEWTON RUBBERFLEX SYSTEM
            Podium Deck and Flat Roof Waterproofing System
            Newton RubberFlex is a BBA Certified single part liquid waterproofing
            material, which forms an elastomeric polyurethane membrane, resisting
            UV rays and capable of handling severe building movements and
            deformations. Newton RubberFlex is guaranteed against deterioration
            for 25 years and is supported by BBA Certification Certificate Number
            11/4840. Newton RubberFlex can be specified as a UV stable
            waterproofing membrane with high resistance to impact and abrasion
            or can be the primary waterproofing barrier when used with Newton
            207 DeckDrain drainage membrane to create a complete drained
            waterproofing solution.

            Newton RubberFlex is available in three variants, the choice of which
            would be dependent on the required speed of application between coats
            as well as on the temperature and humidity at the time of installation and
            the type and height of up-stand to be installed.

            Newton 201 RubberFlex
            Self levelling with standard cure times used for horizontal surfaces and
            up-stands of up to 250mm with reinforcement.

            Newton 202 RubberFlex-QC
            Quick Curing derivative with fast cure times used for horizontal surfaces
            and up-stands of up to 250mm with reinforcement.

            Newton 203 RubberFlex-V
            Thixotropic variant for larger vertical areas.

            Newton RubberFlex can be applied either as a reinforced or a non-
            reinforced system depending on substrate type or substrate quality. See
            product datasheet for more details.

            Application rates: 25kg is sufficient to cover 12.5m2 of surface with a two
            coat treatment of 2kgs per m2 providing an overall membrane thickness
            of 1.9mm (refer to data sheets for suggested drying times between coats)
            Specialist application equipment such as spiked rollers are available
            on request.

            201 RubberFlex and 202 RubberFlex QC are available in 10kg and 25kg
            tins. 203 RubberFlex-V is available in 10kg tins.                                                                                  Page 7

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 200
            Deck & Roofing



            NEWTON 204 THINNER (RF 204)
            Polyurethane Thinning & Cleaning Agent
            Newton 204 Thinner is a slow acting blended solvent for use with Newton
            RubberFlex and Newton 205 ColorSeal. Newton 204 Thinner is used to
            dilute the polyurethane membrane and is especially useful when Newton
            RubberFlex is applied by airless spray.
            Newton 204 Thinner is also used as a cleaning medium for tools and
            equipment used during the application of the membrane and it can
            also be used as a barrier against humidity when having to store product
            already opened. Newton 204 Thinner is supplied in 4kg, 9kg and 20kg
            containers.
            Newton 204 Thinner is also used for cleaning tools used with Newton
            Flexproof products.
            Typical Applications:
            •     Cleaning of tools and equipment
            •     Increasing viscosity of membranes for application by airless spraying
            •     Sealing of product against moisture in opened containers



            NEWTON 205 COLORSEAL (LM 205)
            UV Colour Stable Polyurethane Coating
            Newton 205 ColorSeal is a UV stable, single component, protective
            polyurethane resin top-coat. 205 ColorSeal provides a transparent hard
            wearing coating, or it can be coloured with the addition of pigmented quartz
            sand to provide a textured, slip resistant, UV colour stable finish. Its primary
            use is as a UV stable and hard wearing protection coat above the Newton
            RubberFlex podium deck and flat roof waterproofing system.
            The exceptional strength and durability means that Newton 205 ColorSeal
            can also be used as a stand-alone flooring product. It cures to a gloss
            finish. For pedestrian walkways it is recommended that a coloured quartz
            sand is applied to the still tacky first coat of 205 ColorSeal to give a non-
            slip surface. Newton 205 ColorSeal is supplied in 4kg, 9kg and 20kg
            containers.
            Coverage: a 4kg pack is sufficient to cover a prepared surface area of 13m2
            with the recommended covering of 0.3kg/m2 providing an overall thickness
            of 250-400 microns. With a two coat application which includes the quartz
            sand anti-slip layer, coverage will be 6m2 with the recommended two
            coat treatment
            Typical Applications:
            •     Heavy traffic areas
            •     Industrial factories, depots and warehouses
            •     UV colour stable and non-slip finish to other floor coatings




            Page 8

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 200
            Deck & Roofing


            NEWTON 207 DECKDRAIN (M30)
            Drainage Membrane for Decks and Flat Roofs
            Newton 207 DeckDrain is a double cuspated, deck and flat roof drainage
            membrane, that incorporates a non-woven geotextile filter layer, bonded to
            a water impermeable HDPE (High Density Polyethylene) core. The double
            cuspated design provides two layers of drainage; allowing for primary
            drainage through the geotextile filter, as well as secondary drainage between
            the underside of 207 DeckDrain and the primary waterproofing layer.
            The lower drainage layer eliminates the risk of trapped water, a problem
            associated with conventional single cuspated deck drainage membranes.
            Newton 207 DeckDrain is supplied in 1.1m wide x 25m long rolls and is
            simply laid above the waterproofing membrane with the geotextile fleece
            uppermost.
            Typical Applications:
            As the drainage layer above a deck, balcony or flat roof waterproofing
            membrane such as Newton 201 RubberFlex, particularly where:
            1. Block paviours or flooring slabs are bedded on sand as the surface finish.
            2. Soil filled planters are included to the deck or flat roof.
            Also suitable for use as a vertical drainage layer when used as part of
            a professionally designed and installed externally applied basement
            waterproofing system.




            NEWTON 209 ROOT BARRIER (M32)
            Puncture Resistant Root Barrier Membrane
            Newton 209 RootBarrier is designed to eliminate root penetration. It
            consists of an impermeable High Density Polyethylene (HDPE) membrane,
            providing robust root-proof protection to the primary waterproofing
            membrane to green roofs or planters where intrusive root systems are
            present.
            The membrane has high tensile strength and puncture resistance
            and provides an efficient, reliable and cost effective barrier to provide
            protection against Japanese Knotweed and other aggressive root systems.
            Typical Applications:
            As a root barrier to protect the waterproofing membrane from root damage
            within intrusive green roof systems or planters.

            Newton 209 RootBarrier is supplied in 1.2m wide x 50m long rolls and is
            placed above the waterproofing membrane and the Newton 207 DeckDrain
            (if included in the design). Joints are overlapped by at least 150mm and
            sealed with two lines of Newton Waterseal Tape.




                                                                                                                                               Page 9

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 200
            Deck & Roofing


            NEWTON 210 FLEXPROOF-NV (FP4)
            Waterproofing of Podium Decks and Flat Roofs
            Newton 210 FlexProof-NV is a highly advanced single component liquid
            waterproofing material, which forms an elastomeric polymer membrane
            capable of handling severe building movements and deformations.
            Movement joints to Decks and Flat Roofs can also be waterproofed with
            Newton 201 FlexProof-NV whether the main waterproofing membrane is
            FlexProof-NV or Newton RubberFlex.
            Newton 210 FlexProof-NV has characteristics that allow it to be used
            without a primer, without mixing and in weather conditions that preclude
            the use of alternatives. With a tight project timescale, 210 FlexProof-NV
            can be relied upon to ensure the project is completed on time.
            Newton 210 FlexProof-NV can be used as the primary waterproofing
            membrane below a number of hard finishes and drainage options and
            when partnered with Newton 207 DeckDrain drainage membrane, creates
            a complete drained waterproofing solution to your deck, terrace or flat roof.
            Newton 210 FlexProof-NV is supplied in 7.5kg and 26kg containers and is
            applied to the deck or roof with a squeegee or trowel and is simply poured
            into movement joints.
            Typical Applications:
            • Waterproofing of podium decks, balconies, terraces and flat roofs.
            • As the primary waterproofing membrane below a green roof.
            • As the waterproofing membrane within a warm roof specification.
            • Waterproofing of planters




            NEWTON 220 RESERVOIR (M31)
            Extensive Green Roof Drainage Membrane
            Newton 220 Reservoir is a unique drainage and water retention
            membrane for use where a water reservoir is required for extensive green
            roofs of sedum, herbaceous plants, mosses or grass above decks and
            roofs.
            Unlike other products of this type, Newton 220 Reservoir has a bonded
            geotextile that prevents intrusion of the soil into the water holding cups
            during back-fill and compression. This results in a permanently larger
            volume reservoir than any other 20mm deep green roof membrane.
            When the water holding cups are full, the large drainage holes within the
            HDPE core allow water to easily pass through to the drainage layer below
            to prevent saturation and water logging of the green roof above.
            Typical Applications:
            As a water holding and drainage layer above a deck, flat roof or pitched
            roof where shallow planting is used to create an extensive green roof.

            Newton 220 Reservoir is supplied in 0.92m wide x 50m long rolls and is simply
            laid above the waterproofing membrane with the geotextile fleece uppermost.

            Page 10

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 300
            Waterproofing of Concrete Structures


            NEWTON SYSTEM 300
            WATERPROOFING OF CONCRETE STRUCTURES
            System Overview
            Newton System 300 is a range of products, some unique to John Newton,
            used to waterproof construction joints and movement joints of retained
            concrete structures so that they become integrally waterproof without the
            need of additional waterproofing products, defined within BS8102:2009
            as Type B waterproofing.
            Waterproofing can be further enhanced by the addition of Type A (Newton
            System 100 or System 400) or Type C (Newton System 500) waterproofing
            systems to provide a combined waterproofing approach, recommended
            by BS8102:2009 when absolute waterproofing security is required.
            The podium deck of a retained concrete structure would also require
            waterproofing with one of our System 200 products.



            NEWTON 301 AQUAPROOF
            Metal Construction Joint Water Bar
            Newton 301 AquaProof is a coated metal water bar system used for the
            sealing of construction joints within retained concrete structures.
            Newton 301 AquaProof features an adhesive, reactive
            polymer coating on one of its sides. The coating creates a permanent
            watertight seal with the surrounding concrete to create a water bar that
            works immediately.
            Newton 301 AquaProof is supplied in 6m rolls and is fitted to the
            reinforcing steel with Omega Clips prior to the placing of the concrete.
            Typical Applications:

            •     The waterproofing of construction joints to poured concrete elements
                  of earth retained structures.




            NEWTON 302 INJECTIONHOSE
            Maintainable Injection Water Bar System
            Newton 302 InjectionHose is a high performance injectable water bar
            system used for the sealing of construction joints within retained concrete
            structures.
            The system offers many benefits over conventional water bars,
            especially its ability to grout poorly compacted concrete and by offering a
            maintainable solution that allows for resealing of the construction joint,
            post construction.
            Newton 302 InjectionHose is supplied in reels of 120m and is applied to
            an already formed concrete element prior to formation of the joint.
            Typical Applications:
            •     Post construction grouting and leak sealing of construction joints to
                  poured concrete earth retained structures.                                                                                   Page 11

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 300
            Waterproofing of Concrete Structures


            NEWTON 303 POLYPROOF
            High Grade Hydrophilic Water Bar
            Newton 303 PolyProof is a very high grade hydrophilic water bar which
            seals gaps in construction joints by swelling up to 400% its original size.
            The water bar is adhered to the face of the first pour of the joint with
            either Newton 306 SwellMastic or Newton 309 Contact Adhesive. Can
            also be used as the water bar in settlement or compression joints.
            303 PolyProof is available in the following sizes:

                                               Depth           Width           Length
              303 PolyProof-2                  2mm             20mm            25m
              303 PolyProof-10                 10mm            20mm            10m
              303 PolyProof-30                 30mm            30mm            5m
            Typical Applications:
            •     Waterproofing of static construction joints, settlement joints and
                  compression joints to concrete earth retained structures.


            NEWTON 304 POLYPROOF INJECT
            High Grade Hydrophilic Water Bar
            Unique construction joint water bar that combines the high performance
            swelling capabilities of Newton 303 PolyProof and the post construction
            injection of grouts and resins provided by Newton 302 InjectionHose.
            Newton 304 PolyProof Inject is supplied in coils of 60m and is
            mechanically fixed to the construction joint with special clips.
            Typical Applications:
            •     Waterproofing using hydrophilic swelling and post construction
                  grouting and leak sealing of construction joints to poured concrete
                  earth retained structures.


            NEWTON 305 ACTIVEJOINT
            Physical Movement Joint Water Bar
            MDPE physical water bar for the waterproofing of movement joints. The
            water bar has a unique ‘V’ shape with a number of barbs so that water
            pressure expands the joint, creating more grip to the concrete joint as the
            pressure increases.
            Newton 305 ActiveJoint is supplied in eight widths to waterproof
            movement joints from between 25mm to 100mm. The product is simply
            hammered into a movement joint that has been lubricated with Newton
            306 SwellMastic, which is hydrophilic and will swell in contact with water
            to further waterproof the joint.
            Typical Applications:
            •     Waterproofing of movement joints.


            Page 12

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 300
            Waterproofing of Concrete Structures


            NEWTON 306 SWELLMASTIC
            Swelling Adhesive
            Newton 306 SwellMastic is a high performance mastic used to adhere
            Newton 303 PolyProof and Newton 305 ActiveJoint to the concrete joint.
            Can also be used to seal around protrusions such as pipes and conduits
            and should be used to reinforce Newton 307 PipeSeal being fitted to
            pipes passing through the structure.
            Newton 306 SwellMastic is supplied in cartridges of 290ml and foil
            sausages of 600ml and is applied in a bead.
            Typical Applications:
            •     Sealing around protrusions through the structure such as service
                  pipes and as an adhesive for Newton 303 PolyProof, 304 PolyProof
                  Inject and 305 ActiveJoint.


            NEWTON 307 PIPE SEAL
            Pipe Collar
            Newton 307 PipeSeal is a preformed MDPE seal that creates a physical,
            flanged joint around pipes passing through the structure. Newton 306
            SwellMastic should be used to reinforce the joint.
            Newton 307 PipeSeal is available for sealing pipes of diameters of
            110mm and 160mm and they are simply slipped over the pipe using
            neutral soap as a lubricant.
            Typical Applications:
            •     Sealing around pipes protruding through the structure.



            NEWTON 308 STOPAQ (SX 308)
            Unique Hydrophilic Polymer Sealant
            Newton 308 Stopaq is a unique swelling sealant compound system
            which provides a waterproofing solution for the notoriously difficult to seal
            service pipe penetrations through retaining walls.
            Newton 308 Stopaq is supplied in 0.53kg tubes and is applied with a
            specialist applicator gun. The product cartridge needs to be warmed prior
            to installation by submersing in warm water.
            Typical Applications:
            •     Sealing around cables, conduits and other difficult to seal protrusions
                  through the structure whether in sleeve pipes or directly through the
                  concrete.




                                                                                                                                               Page 13

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 400
            External Waterproofing


            NEWTON SYSTEM 400 - EXTERNAL WATERPROOFING
            System Overview
            System 400 is a range of products for the waterproofing of the outside
            of earth retained structures. Products include sheet membranes for the
            complete envelopment of the raft and walls, flexible liquid products for the
            waterproofing of retained walls and composite drainage membranes for
            preventing the build up of ground water to the walls or below the raft.
            Newton System 400 products can provide Type A and Type B
            waterproofing to Grades 2 & 3 as defined within BS8102:2009 Code of
            Practice for the Protection of Below Ground Structures Against Water from
            the Ground.




            NEWTON 401 FLEXPROOF-X1
            Flexible Membrane for Retaining Walls
            Newton 401 FlexProof-X1 is a highly advanced single component liquid
            waterproofing material, which forms an elastomeric polymer membrane
            that is rainproof in minutes and capable of handling severe building
            movements and deformations.
            401 FlexProof-X1 has characteristics that allow it to be used without a
            primer, without mixing and in weather conditions that preclude the use of
            alternatives.
            Newton 401 FlexProof-X1 comes in containers of 15kg & 26kg which is
            applied by trowel in one coat of 3kg/m2.
            Suitable Substrate:
            •     Concrete or masonry retained walls.

            Key Benefits
            •     No mixing required – simply open the packaging and use.
            •     Can be used in sub-zero temperatures and on slightly damp
                  substrate.
            •     No primer required – saving on primer and labour costs
            •     Single coat application.
            •     100% waterproof, but allows vapour diffusion.
            •     Very flexible – Resistant to movement and fissures in substrates.
            •     Excellent adhesion to suitable substrates.
            •     Resistant to temperature variations maintaining its characteristics
                  between -40ºC & 90ºC.
            •     Excellent resistance to the high alkalinity of concrete




            •
            Page       14

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 400
            External Waterproofing


            NEWTON 402 AQUABIT
            Flexible Membrane for Retaining Walls
            Newton 402 Aquabit is a single component water based waterproofing
            bituminous mortar that includes polystyrene micro-spheres that allow it
            to be applied obtaining a level of thickness up to 3mm, modified to make
            the product extremely workable and able with just one coat to fill surface
            irregularities, typical on concrete foundation walls. The material is also
            characterised by a high elasticity, crack bridging ability and a good salt
            resistance. It can be applied both on old and new walls.
            Newton 402 Aquabit comes in containers of 25 litres which is applied by
            trowel in one coat of 2.2 litres per m2 to give an average thickness
            of 2.5mm.
            Typical Applications:
            •     Waterproofing of retained walls




            NEWTON 403 HYDROBOND
            Hydrophilic and Bonding Membrane for Raft and Wall Waterproofing
            Newton 403 HydroBond is a very high performance composite sheet
            membrane that features a locking fleece to one side and a polymer
            hydrophilic coating to the other side.

            When placed below the new raft or against the wall shuttering, the
            poured concrete engages into the locking fleece so that the membrane is
            completely locked in and monolithic to the concrete thus ensuring that if
            a leak did occur it cannot track to the construction joints. The hydrophilic
            coating seals small holes that may be accidentally formed during fixing of
            the reinforcing steel or the pouring or compaction of the concrete.

            Newton 403 HydroBond is supplied in rolls of 2m x 30m and can be laid
            to the blinding and shuttering of a raft construction or adhered to already
            formed retaining walls.
            Typical Applications:

            •     Waterproofing of retained walls
            •     Waterproofing of decks




                                                                                                                                               Page 15

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 400
            External Waterproofing


            NEWTON 410 GEODRAIN (M18)
            Externally Applied Drainage Membrane
            Newton 410 Geodrain is a component drainage sheet consisting of a
            non-woven geotextile filter layer thermally welded to a water impermeable
            HDPE drainage membrane. Newton 410 Geodrain provides outstanding
            drainage and protection to the outside face of basement walls, preventing
            the build-up of water pressure and protecting the structure from
            aggressive water, chemicals and toxins.
            Newton 410 Geodrain comes in rolls which are 2m x 12.5m with a surface
            coverage of 25m2 (in-line studs 10mm in depth)
            Typical Applications:
            •     As the drainage layer of an externally applied waterproofing system
                  when used in conjunction with sheet applied or liquid applied external
                  tanking membrane to BS8102:2009

            •     Protection of the structure from aggressive chemicals in the ground water

            •     To prevent the build up of ground water to retaining walls




            Page 16

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 500
            Cavity Drain Waterproofing


            NEWTON SYSTEM 500 - CAVITY DRAIN WATERPROOFING
            System Overview
            The professional’s “waterproofing system of choice”, Newton System 500
            is an internally applied waterproofing system based upon our range of
            cavity drain membranes, drainage conduits and sophisticated pumping
            and control systems.
            Unlike conventional ’tanking’, Newton System 500 is not attempting the
            almost impossible and trying to hold water back, but places designed
            maintainable depressurisation voids at known weaknesses in the
            structure so that ingressing water is simply captured and diverted out
            of the property. Newton recommends that our structural waterproofing
            systems are installed by one of our Nationwide Network of Newton
            Specialist Basement Contractors who have been trained by Newton
            and can offer full professional indemnity on design and insured backed
            guarantee on the installation.


            NEWTON 503 (M5)
            3mm Cavity Drain Membrane for Basement Walls, Floors & Vaulted Soffits
            Newton 503 is a BBA approved cavity drain waterproofing membrane
            suitable for use internally to retaining walls, vaulted soffits and floors.
            Newton 503 is a flexible HDPE membrane which at 0.5mm in thickness
            provides a low profile drainage solution within the Newton Cavity Drain
            membrane range.
            Newton 503 (M5) is available in rolls 2m x 20m - 40m2




            NEWTON 503 MESH (M11 & M12)
            3mm Cavity Drain Membrane for Basement Walls, Floors & Vaulted Soffits
            Newton 503 Mesh is a BBA certified meshed membrane suitable for use
            as a waterproofing membrane when used below the ground as part of
            Newton System 500.
            With its 3mm stud, Newton 503 Mesh is just 3.5mm in overall thickness,
            and is the preferred meshed membrane where space is at a premium.
            Its meshed surface provides an excellent ’key’ for lime mortars, renders,
            plasters or dabbed plasterboard. When using Newton 503 Mesh, it is
            essential to use Newton MultiPlug or Newton NuSeal with WaterSeal Rope
            as a means of achieving a waterproof seal.
            Newton 503 Mesh is available in roll sizes 1m x 20m -
            20m2 (M12) and 2m x 20m - 40m2 (M11)




                                                                                                                                               Page 17

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 500
            Cavity Drain Waterproofing


            NEWTON 508 (M1 & M2)
            8mm Cavity Drain Membrane for Basement Walls, Floors & Vaulted Soffits
            Newton 508 is our high quality BBA approved cavity drain waterproofing
            membrane suitable for use internally below the ground to retaining walls,
            vaulted soffits and floors. Newton 508 is our flagship membrane and one
            of the most specified cavity drain membranes in the UK. The 0.7mm thick
            HDPE product allows for large industrial loads to be applied and the in line
            studs allow for quick installation with minimal surface preparation.
            Newton 508 is available in roll sizes 2.4m x 20m - 48m2
            (M1) and 2m x 20m - 40m2 (M2)


            NEWTON 508 MESH (M3)
            8mm Meshed Cavity Drain Membrane for Basement Walls,
            Floors & Vaulted Soffits
            Newton 508 Mesh is a BBA approved meshed cavity drain waterproofing
            membrane, suitable for use internally below the ground to retaining walls
            and vaulted soffits. Newton 508 Mesh is typically used where space
            prevents the use of a dry-lining frame or block wall as the wall finish
            or where a direct rendered or plastered finish is preferred. The ability
            to apply direct finishes to the product makes it ideal for convoluted or
            confined basement areas where space is at a premium or where the
            original contours (features) of the property need to be retained.
            Newton 508 Mesh (M3) is available in rolls 2m x 20m -
            40m2


            NEWTON 520 (M4 & M13)
            20mm Cavity Drain Membrane for Basement Floors
            Newton 520 is a BBA approved cavity drain membrane suitable for use
            above basement floor areas. The 20mm studded membrane allows for
            a massive flow rate to pass underneath the membrane and is specified
            where floor areas are of questionable quality or where it is anticipated
            that there may be a risk of severe water penetration.
            Newton 520 is available in roll sizes 2m x 20m - 40m2
            (M4) or 2m x 10m - 20m2 (M13)



            NEWTON BASEDRAIN (D1)
            Drainage System
            Newton Basedrain comprises a range of products that receive water
            ingressing at weaknesses within the structure and then discharge the
            collected water to a Newton Sump System or safe drainage (drainage that
            is below the level of the basement floor that cannot back-up or block).
            Basedrain is supplied in packs of 12 linear metres (6 x 2m) lengths.
            Internal and external corners, T pieces, drainage connectors and access/
            jetting ports should be utilised with Basedrain. Contact us for more details.

            Page 18

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 600
            Flooring Membranes


            NEWTON SYSTEM 600 - FLOORING MEMBRANES
            System Overview
            Newton System 600 is a range of HDPE and HDPP flooring membranes
            offering a complete damp proof solution for both commercial and
            domestic flooring applications. As well as providing protection from
            dampness within the floor, our membranes ‘de-couple’ the floor finish
            from the substrate preventing damage due to substrate movement and
            cracking. Newton damp proof membranes can be installed over existing
            and ‘green’ concrete.
            In addition our flooring membranes are a popular solution for dealing
            with inherent hydrocarbons or ground gas problems. Newton flooring
            membranes can accommodate a variety of finishes including timber
            floors, screeds and direct tiles.


            NEWTON 601 SLIMLINE (M6)
            Flat Loose Laid High Grade Flooring Membrane
            Newton 601 Slimline is a high-grade flooring membrane used primarily for
            isolating moisture sensitive flooring from dampness in the floor slab, but
            can also be used as the floor membrane as part of Newton System 500
            when the survey has ascertained that no risk of water entering through
            the body of the slab exists.
            Newton 601 Slimline allows for the installation of sensitive flooring to
            be laid above ’green’ still curing concrete as soon as the concrete is
            walkable, usually two days, significantly reducing project times. With a
            loading capability of over 1000kN/m2, Newton 601 Slimline is able to
            resist very high compressive loading and is suitable for use as a high
            load DPC within structural block walls, especially when used to connect
            the wall and floor membranes within Newton System 500. Newton 601
            Slimline is made from HDPP and is the thinnest profile membrane within
            the Newton floor membrane portfolio.
            Newton 601 is available in rolls 2.07m x 20m - 40m2 (M6)


            NEWTON 603 (M23)
            3mm Loose Laid Flooring Membrane
            Newton 603 is suitable for use above new and existing floors. The 3mm
            studs allow for pressure equalisation of dampness within the floor below
            allowing for dissipation at room perimeter and subsequent drying of the
            floor. The studs also give slight compression to footfall making the floor
            very responsive and comfortable and ideal as the floor membrane for
            performance sports floors. Newton 603 uncouples the floor finish from
            the substrate so that movement is not transferred to the floor finish
            above. The membrane also bridges small cracks allowing for quick floor
            installation above less than ideal substrate.
            Newton 603 is available in rolls 2m x 20m - 40m2 (M23)



                                                                                                                                               Page 19

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 600
            Flooring Membranes


            NEWTON 603 MESH (M24 & M25)
            Loose Laid 3mm Flooring Membrane with Meshed Surface
            Newton 603 Mesh is high grade flooring membrane with an installation
            height of 3.5mm. The white HDPE cuspated core has a polyethylene mesh
            above allowing for adhesion of the floor finish to the membrane.
            Newton 603 Mesh is loose laid above the substrate and is therefore
            uncoupled from the floor ensuring that the floor finish is not affected by
            movement or cracking of the substrate.
            Newton 603 Mesh is available in rolls 1m x 20m - 20m2 (M24) and
            2m x 20m - 40m2 (M25)




            Page 20

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 700
            Liquid Applied Floor Coatings


            NEWTON SYSTEM 700 - LIQUID APPLIED FLOOR COATINGS
            System Overview
            System 700 is our range of liquid applied protective and decorative
            internal flooring products. These products are fast curing and available
            in a variety of colours, and are typically used for the refurbishment and
            protection of commercial and domestic floors.




            NEWTON 701 HB (LM 701)
            High Build Epoxy Floor Coating
            Newton 701 HB is a two-component solvent free water based epoxy
            resin based floor coating developed to provide protective and decorative
            properties to concrete, steel and other substrates. The material is
            supplied as a two-pack system comprising pre-weighed amounts of base
            and curing agent. After mixing together, an easily applied chemical and
            abrasion resistant finish is produced. This acts as a waterproof, tough,
            chemical resistant floor coating or as an internal lining for concrete or
            steel storage tanks containing oils, chemicals, water, etc. It is particularly
            suitable for chemical bunds.
            Typical Applications:
            • Food preparation areas             • Breweries
            • Industrial units                   • Warehouses
            • Garages
            • Below ground structures where Newton drainage conduits are utilised



            NEWTON 702 ECOSEAL (LM 702)
            Highly Resistant Polyurethane Floor Coating
            Newton 702 EcoSeal is a two component, solvent free, high performance
            Aliphatic Polyurethane resin which provides a hard yet flexible floor
            coating, with very high abrasion and chemical resistance. It provides
            excellent surface protection to floorings exposed to high wear and traffic.
            Newton 702 EcoSeal is supplied as a transparent coating for use above
            coloured bases such as Newton 701 HB or it can be coloured on site with
            RAL colours through the addition of pigment pastes and used above a
            suitable Newton primer as the stand-alone floor finish. The total absence
            of solvents allows for application in unventilated indoor areas. Newton
            702 EcoSeal cures to a UV stable gloss finish.
            Typical Applications:
            • Heavy traffic areas
            • Industrial factories, depots and warehouses
            • Indoor tennis courts and recreational areas
            • Hard wearing finish to other floor coatings
            • Indoor car parks

                                                                                                                                               Page 21

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 800
            Damp Proofing


            NEWTON SYSTEM 800 - DAMP PROOFING
            System Overview
            Newton System 800 is a range of BBA approved damp proof membranes
            and ancillaries which are quick and clean to install and offer a permanent
            solution for damp proofing walls.
            Newton 805 Newlath and Newton 803 Newtonite meshed membranes
            provide a firm key and impermeable barrier on any damp or deteriorating
            surface ready for plaster, render or dot & dab plasterboard.
            The un-meshed Newton 803 is used where insulation requirements
            dictate the use of a timber or steel frame ready for plasterboard. Quick,
            clean and proven to work, Newton damp proof membranes offer a
            permanent and cost effective damp proofing solution.




            NEWTON 805 NEWLATH (M9 & M10)
            5mm Meshed Damp Proofing Membrane
            Newton 805 Newlath (formerly Newlath 2000) is a BBA approved high
            density polypropylene membrane with a rot-proof polythene mesh
            heat-welded during the manufacturing process to the surface of one side.
            The meshed surface creates a mechanical key to allow the membrane to
            be plastered, rendered or to receive dot & dab plasterboard. Newlath can
            be applied internally as a means of dealing with all forms of dampness
            inherent in structures and externally to properties suffering from driving
            and penetrating moisture.
            With over two million metres of Newton 805 Newlath installed nationally,
            Newlath is a cost effective and permanent method of dealing with
            dampness.
            Typical Applications
            • Internally for dealing with rising damp, salts and contaminants within
                 existing structures.
            • Externally for protection of brick and masonry structures from driving
                 and penetrating moisture
            • Treating dampness in listed buildings as the system is deemed
                 removable and reversible and is sympathetic to the building fabric.
            • Applied to timber frame properties which require a rendered finish.

            Newton 805 Newlath is available in rolls 1.5m x 10m -
            15m2 (M9) and 2m x 20m - 40m2 (M10)




            Page 22

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 800
            Damp Proofing


            NEWTON 803 (M19 & M20)
            Non-Meshed Damp Proofing Membrane
            Newton 803 is a non-meshed damp proofing membrane for use above the
            ground. It can be used as an alternative to Newton 803 Newtonite and
            805 Newlath where a meshed surface is not required as a surface for
            direct plastering or rendering. Newton 803 is typically used where the wall
            finish to the damp-proof membrane is timber battens, a dry-lining frame
            or block wall.
            Newton 803 is 0.5mm thick and has a pattern of raised 3mm studs.
            The studs face the wall and create air channels that allow for vapour
            equalisation to take place between the membrane and the wall.
            Newton 803 is available in roll sizes 2m x 20m - 40m2
            (M20) and 1m x 10m - 10m2 (M19)




            NEWTON 803 NEWTONITE (M16, M21, M22)
            3mm Meshed Damp Proofing Membrane
            BBA approved Newton 803 Newtonite provides a firm key and
            impermeable barrier on any damp or deteriorating surface where direct
            bonding is not possible. Even poor and random substrates can easily
            receive Newtonite.
            Newtonite presents a physical barrier between the old surface and the
            new internal finish. Unlike many systems it can be punctured when new
            wall fixings are required. Holes drilled through the material must however
            be well sealed with Newton Mastic to stop any dampness
            bridging between the existing and new surface.
            Newtonite 803 is available in roll sizes:
            1m x 10m - 10m2 (M16), 1m x 20m - 20m2 (M21)
            and 2m x 20m - 40m2 (M22)



            NEWTON 801 FLEXPROOF-X1 (FP1)
            Wet-room Waterproofing
            Newton 801 FlexProof-X1 is a highly advanced single component liquid
            waterproofing material, which forms an elastomeric polymer membrane
            that is splash proof in minutes and capable of handling severe building
            movements and deformations.
            Newton 801 FlexProof-X1 has characteristics that allow it to be used
            without a primer, without mixing and in weather conditions that preclude
            the use of alternatives. When applied by trowel to wet-room walls, 801
            FlexProof-X1 provides a continuous highly flexible membrane which can
            be blinded with sand ready for the tiled finish.
            Newtonite 801 FlexProof-X1 is available in containers of 15kg & 26kg



                                                                                                                                               Page 23

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 800
            Damp Proofing

            The ancillaries below are used with the three damp-proofing membranes that are included within Newton System
            800. Newton 803 is a plain membrane used where a dry-lining frame or a block wall is to be used as the wall
            finish. 803 Newtonite and 805 Newlath are meshed membranes used where a surface key is required for direct
            plastering, rendering or dot and dabbing to the wall membrane. Please read the membrane product data sheets
            for more information.

              Membrane              Fixing Plug             Jointing Tape                Sealing Drilled Hole Plaster Stop                     Repairs
              803                   MultiPlug               Newton Overtape              Not Required                     Not required         Newton Overtape
              803 Newtonite 800 Mesh or                     Newton Mesh Tape             Newton 800 Mastic                Newton 800 Profile   Newton Mesh Tape
                            Newtonite Plug
              805 Newlath           800 Mesh or             Newton Mesh Tape             Newton 800 Mastic                Newton 800 Profile   Newton Mesh Tape
                                    Newtonite Plug


            NEWTON 800 MESH PLUG (A16)
            Above ground the Newton 800 Mesh Plug can be used internally and
            externally to secure Newton meshed membranes: 805 Newlath and
            803 Newtonite. Once the hole is drilled it should be primed with Newton
            Mastic sealant to prevent dampness tracking back along the plug.

                            Size (Width x Length) 7mm x 50mm
                                 Quantity Per Bag 250


            NEWTON MULTIPLUG (A1)
             Newton MultiPlug is used with Newton 803. Drill a 10mm hole through
             the 803 membrane and hammer home with a club hammer. The
             MultiPlug can take a 5mm dia screw to allow the fixing of battens and
             dry-lining frames and the Newton Helifix Wall Tie without breaching
             the membrane. MultiPlug Pins are sold separately.

                            Size (Width x Length) 10mm x 57mm
                                 Quantity Per Bag 100


            NEWTON 800 COB PLUG (A17)
            In above ground situations, the Newton Cob Plug is used with 803
            Newtonite and 805 Newlath membranes. It has an expanding stem which
            provides effective anchorage in a wide range of base materials. Larger
            sizes of Newton Cob Plug can be sourced on request.

                            Size (Width x Length) 7mm x 90mm
                                 Quantity Per Bag 50



           NEWTON 800 NEWTONITE PLUGS (A20)
           Above ground the Newtonite Plugs can be used internally to secure
           Newton 803 Newtonite and 805 Newlath membranes. Once the hole
           is drilled it should be primed with Newton Mastic sealant to prevent
           dampness tracking back along the plug.

                            Size (Width x Length) 7mm x 50mm
                                 Quantity Per Bag 160


            Page 24

                             © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                       www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 800
            Damp Proofing


            NEWTON 800 MASTIC (A18)
            Newton Mastic is used with 805 Newlath and 803 Newtonite. It is used
            to prime the plug hole prior to the fixing plug being hammered home,
            which serves to stop any ‘bridge’ happening between the damp or stained
            surface and the new surface. Newton Mastic is also used for sealing
            around protrusions.

                                       Unit of Sale 0.38 litre tube




            NEWTON MESH TAPE (A25)
            Newton Mesh Tape is used to joint 803 Newtonite and 805 Newlath
            membranes as well as for repairs to the membrane and for sealing
            around protrusions. The meshed surface gives a good key for renders
            and plasters.

                            Size (Width x Length) 100mm x 10m
                                     Unit of sale Single units




            NEWTON OVERTAPE (A8)
            Newton Overtape is used for the jointing of Newton 803 as well as for
            repairs to Newton 803 and to seal around protrusions to the membrane.


                            Size (Width x Length) 100mm x 20m
                                     Unit of sale Single units




            NEWTON 800 PROFILE (A19)
            Newton Profile can be used with 803 Newtonite and 805 Newlath. It
            serves as a plaster stop, guaranteeing that the plaster/render will stop
            short of the floor.
                                               Size 2m lengths
                                       Unit of Sale Single units




                                                                                                                                               Page 25

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 900
            Liquid Primers & Sealers


            NEWTON SYSTEM 900 - LIQUID PRIMERS & SEALERS
            System Overview
            Newton’s high performance range of liquid applied products are used in
            conjunction with System 200 and 700 liquid membranes. They act as
            priming agents for a variety of substrates prior to the application of our
            specialist waterproofing and flooring membranes.




            NEWTON 901 HUMIDITY PRIMER (PS 901)
            Epoxy Primer Suitable for High Humidity Substrate
            Newton 901 Humidity Primer is a solvent free two part epoxy resin coating
            typically used as a primer for Newton high performance liquid applied or
            sprayed roofing and flooring products.
            Newton 901 Humidity Primer would be chosen as the primer coating
            where the substrate contains humidity levels in excess of 4%.
            Application
            Mix Part A - Epoxy Resin with Part B - Hardener thoroughly with an electric
            paddle mixer for 2 min until a milky uniform colour is achieved (pot life of
            approx 30 minutes)
            Application rate is 0.3 kg per m2 dependent on the quality of the
            substrate. Newton 901 Humidity Primer is supplied in 5kg, 10kg and
            20kg components.




            NEWTON 902 (PS 902)
            Liquid Applied Radon, Gas & Vapour Barrier
            Newton 902 is a single component high performance elastomeric liquid
            rubber membrane specifically designed for providing a radon, gas and
            vapour barrier to vertical and horizontal surfaces. Newton 902 is a cost
            effective vapour barrier material which can easily be applied via a stiff
            brush, roller or airless sprayer to a variety of different substrates including
            concrete, mortar, brick, Insulated Concrete Formwork (ICF), ceramics,
            steel, zinc or aluminium.
            Pre-dampen porous substrates prior to the application of the first coat.
            Application
            Newton 902 can be used as a primer for other Newton liquid membranes
            when applied in one coat of 0.33kg per m2 or as a gas, vapour and
            waterproofing membrane with two coats totalling 1kg per m2
            Newton 902 is supplied in 5kg, 10kg and 20kg tubs.




            Page 26

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SYSTEM 900
            Liquid Primers & Sealers


            NEWTON 903 PU PRIMER (PS 903)
            Epoxy Primer for Nonporous Substrate
            Newton 903 PU Primer is used for priming non-absorbent substrates,
            prior to application of Newton high performance liquid applied roofing and
            flooring products.
            It should be chosen as the primer where the substrate is nonporous such
            as ceramic, steel, glass, marble, polished concrete etc.
            Newton 903 PU Primer can be applied with roller, brush or cloth to a ratio of
            0.1kg per m2
            Newton 903 PU Primer is supplied in units 4kg, 9kg or 20kg




            NEWTON 904 HP ACCELERANT (PS 904)
            Humidity Primer Accelerant
            Newton 904 HP Accelerant is a clear accelerant additive for exclusive
            use with Newton 901 Humidity Primer. The addition of Newton 904 HP
            Accelerant to Newton 901 Humidity Primer results in the primer being
            cured in 1 to 2 hours (diminishing the risk of alteration by rain, wind, etc.)
            The accelerated curing is achieved without any loss in its properties or
            changes in the chemical structure of the primer.
            Newton 904 HP Accelerant is supplied in 1kg units and has been
            designed to be added to a 20kg unit of Newton 901 Humidity Primer.
            Add the 1kg unit of Newton 904 HP Accelerant to the 20kg unit of the
            901 Humidity Primer once both parts A and B have been already mixed.
            Totally mix and homogenise both products together.
            Note: After adding 904 HP Accelerant to the 901 Humidity Primer the pot
            life is shortened to only 20-30 minutes and the combined product cannot
            be reused.



            NEWTON 906 MOULD STOP (PS 906)
            Mould Steriliser & Killer
            Newton 906 Mould Stop can eradicate mould in four easy steps. It is
            simple to use and as well as killing dangerous mould it prevents regrowth
            and eliminates musty odours.
            Newton 906 Mould Stop is suitable for walls, ceilings, skirting boards,
            window reveals, uPVC window and door frames.
            906 Mould Stop kit contains: 1 litre of Mould Stop Steriliser and Killer
            Spray, 1 x safety glasses, 1 x pair of disposable gloves, 1 x sponge and
            2 x 100ml Mould Stop Paint Additive.
            Once mixed Newton 906 Mould Stop will treat between 10 and 15m2



                                                                                                                                               Page 27

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON FLEXPROOF
            Construction Joint Waterproofing


            NEWTON FLEXPROOF
            Highly Advanced Single Component Liquid Waterproofing Material

            Newton FlexProof-X1 forms an elastomeric polymer membrane that is
            rainproof in minutes and capable of handling severe building movements
            and deformations.
            FlexProof-X1 has characteristics that allow it to be used without a primer,
            without mixing and in weather conditions that preclude the use of
            alternatives.
            FlexProof-X1 is a multi-use product and can be applied by trowel or
            squeegee to a variety of different surfaces such as concrete, screed and
            timber boards to provide a continuous highly flexible membrane that is
            resistant to water pressures of up to 2 bar (20m) over construction joints
            of up to 0.25mm.
            Key Benefits:
            •     No mixing required - simply open the packaging and use.
            •     Can be used in sub-zero temperatures and on slightly damp
                  substrate.
            •     No primer required - saving on primer and labour costs
            •     Single coat application.
            •     100% waterproof, but allows vapour diffusion.
            •     Very flexible - Resistant to movement and fissures in substrates.
            •     Excellent adhesion to suitable substrates.
            •     Resistant to temperature variations maintaining its characteristics
                  between -40ºC & 90ºC.
            •     Excellent resistance to the high alkalinity of concrete.




            NEWTON FLEXPROOF-X1 (FP1)
            Construction Joint Waterproofing
            For the waterproofing of construction joints in new-build concrete
            construction of basements. When applied by trowel or squeegee over
            construction joints in concrete, FlexProof-X1 provides a continuous highly
            flexible membrane that is resistant to water pressures of up to 2 bar
            (20m) over construction joints of up to 0.25mm.
            Suitable Substrate:
            • Construction and movement joints to basement structures built of
                concrete.
            •     Retained walls built in concrete or concrete block.
            •     Construction and movement joints to decks and flat roofs built of
                  concrete or timber.
            •     Wet rooms built of concrete, masonry or timber.


            Page 28

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON DIATHONITE
            Insulating Plaster


            NEWTON DIATHONITE
            Eco Thermal Plaster with Insulation and Acoustic Properties
            Newton Diathonite is a premixed plaster, fibre-reinforced with cork
            (granular 0-3 mm), clay powders and NHL 3.5 natural hydraulic lime.
            The resulting natural compound produces a plaster with unrivalled
            thermal and acoustic properties that is both hard wearing and flexible
            which is ideal for both internal and external applications.
            Diathonite, when applied either internally or externally, creates a
            seamless thermal barrier which eliminates any risk of cold bridging within
            the structure. To achieve very high thermal and acoustic performance,
            Newton Diathonite will need to be applied at a thickness that is similar to
            those of standard wall insulation.
            One of the big advantages of applying Newton Diathonite to existing
            properties is that the application can be split between internal and
            external application, whereas conventional insulation can only be added
            to the inside of the walls and so impacts greatly on the internal space.
            It is usual for the internally applied insulation to then have a covering,
            such as plasterboard, which further reduces habitable space. By splitting
            the application of Diathonite between the inside and outside of the wall,
            similar insulation characteristics can be achieved with just half the space
            loss of conventional insulation.

            Key Benefits
            •     Superb insulation properties thanks to the air spaces created by
                  natural cork particles included within the plaster
            •     High vapour permeability
            •     Resistant to fire: Class 1
            •     Eco-friendly
            •     Can be spray applied allowing for very fast application
            •     Very flexible - large elevations can be plastered without cracking
            •     Impressive acoustic characteristics - over twice the performance of
                  conventional plasters or renders

            Typical Applications

            •     As a high performance insulated plaster for both the inside and
                  outside of external walls

            •     As a sound insulating plaster for both external and internal walls




                                                                                                                                               Page 29

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SUMP AND PUMP
            Pumping Product Range


            NEWTON SUMP AND PUMP
            System Overview
            Newton have an extensive range of submersible pumps and pumping
            ancillaries. We supply the highest quality pumps available in each class,
            for the control of clean ground water, grey water, effluent or sewage.




            CLEAN/GROUND WATER PUMPS

            NEWTON NP150 (P1)
            Medium head and low to medium duty pump. The NP150 is an automatic
            pump, with integral vertical float switch and so is not suitable for use with
            our pump control panels. It can be used with Newton Power Converters of
            1200W or over to give continual pumping even when the power is out.
            The NP150 is supplied with a one way check valve and should be used
            with 50mm pressure rated discharge pipe. The pump is sold as pump
            only, or as a key component in our Newton Titan-2 packaged pump
            system.
            3 year manufacturers warranty.




            NEWTON CP250 (P31)
            The Newton CP250 is a low cost and high quality clean water pump ideally
            suited for the removal of ground water from basements and cellars. The
            unique vertical operation float switch ensures that the pumps operate
            within the pump footprint removing the possibility of the float snagging
            during operation and allowing the pumps to be used within smaller
            sumps. The vertical float switch is also very flexible, allowing the pump
            switching height to be adjusted both in height between the ‘on’ and ‘off’
            positions, but also in height relative to the pump.
            The CP250 is supplied with a one way check valve and and should be
            used with 50mm pressure rated discharge pipe.
            The pump is sold as pump only, or as a key component in our Newton
            Titan-2 and Newton Titan-Pro packaged pump systems.
            1 year manufacturers warranty or 3 year Newton warranty with proven
            service history.




            Page 30

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                       www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SUMP AND PUMP
            Pumping Product Range


            NEWTON CP400 (P32)
            The Newton CP400 is a low cost and high quality clean water pump ideally
            suited for the removal of ground water from basements and cellars. The
            unique vertical operation float switch ensures that the pumps operate
            within the pump footprint removing the possibility of the float snagging
            during operation and allowing the pumps to be used within smaller
            sumps. The vertical float switch is also very flexible, allowing the pump
            switching height to be adjusted both in height between the ‘on’ and ‘off’
            positions, but also in height relative to the pump.
            The CP400 is supplied with a one way check valve and should be used
            with 50mm or 63mm pressure rated discharge pipe. The pump is sold
            as pump only, or as a key component in our Newton Titan-2 and Newton
            Titan-Pro packaged pump systems.

            1 year manufacturers warranty or 3 year Newton warranty with proven
            service history.

            NEWTON NP400 (P2 & P3)
            Available in both manual (P3) and automatic (P2) versions, the NP400 is
            the most popular high performance submersible pump in our portfolio.
            The NP400 has a unique vertical float mechanism which can be adjusted
            to suit each individual pumping assignment. It can be used with Newton
            Power Converters of 1200W or over to give continual pumping even when
            the power is out.
            The NP400 is supplied with a one way check valve and should be used
            with 50mm or 63mm pressure rated discharge pipe. The pump is sold
            as pump only, or as a key component in our Newton Titan-2 and Newton
            Titan-Pro packaged pump systems.
            3 year manufacturers warranty.


            NP400PP (P13) & NP400LLPS (SP1)
            The Newton NP400PP is a high quality puddle pump able to pump water
            down to just 1mm. The NP400PP is a manual pump with no switching
            control - the pump will run continually when connected to a power supply.
            Switching of puddle pumps is problematic because by their nature they
            are dealing with low heights of water. This makes conventional switching
            difficult.
            The NP400LLPS is the switched version of the NP400PP Puddle Pump.
            The NP400LLPS has a small control panel and low level switching
            module added to the NP400PP Puddle Pump that will give accurate and
            safe switching on of the pump at water levels of just 10mm. The NP400
            LLPS will pump down to just 1mm of water depth. The NP400PP and
            NP400LLPS are supplied with a one way check valve and should be used
            with 50mm pressure rated discharge pipe.
            3 year manufacturers warranty.




                                                                                                                                               Page 31

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                       www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SUMP AND PUMP
            Pumping Product Range


            NEWTON CP750 (P33)
            The Newton CP750 is a low cost and high quality clean water pump ideally
            suited for the removal of ground water from basements and cellars. The
            unique vertical operation float switch ensures that the pumps operate
            within the pump footprint removing the possibility of the float snagging
            during operation and allowing the pumps to be used within smaller
            sumps. The vertical float switch is also very flexible, allowing the pump
            switching height to be adjusted both in height between the ‘on’ and ‘off’
            positions, but also in height relative to the pump.
            The CP750 can be supplied with a choice of one way valves and should
            be used with 50mm or 63mm pressure rated discharge pipe.
            The pump is sold as pump only, or as a key component in our Newton
            Titan-Pro packaged pump system.
            1 year manufacturers warranty or 3 year Newton warranty with proven
            service history.


            NEWTON NP750 (P5 & P6)
            The Newton NP750 is a high performance pump available as an
            automatic pump (P5), or as a manual pump (P6) for use with the CP2
            Control Panel. It can be used with Newton Power Converters of 3000W to
            give continual pumping even when the power is out.
            For increased duty in a twin pump system, separate discharge lines
            should be used. The NP750 is sold as pump only, or as a key component
            in our Newton Titan-Pro packaged pump system and should be used with
            50mm or 63mm pressure rated discharge pipe.
            3 year manufacturers warranty.




            EFFLUENT PUMP (NOT SEWAGE)
            NEWTON NP400W (P4)
            The Newton NP400W is a medium head and medium performance pump
            specifically placed within the Newton pumping range for when dishwasher,
            washing machine or bath/shower waste is to be removed from the
            sump. It is an automatic pump with a specially designed adjustable float
            arrangement that cannot be fouled by hardened soaps etc. It can be
            used with Newton Power Converters of 1200W or over to give continual
            pumping even when the power is out.
            The NP400W is sold as pump only, or as a key component in our Newton
            Titan-Pro packaged pump system and should be used with 50mm and
            63mm pressure rated discharge pipe.
            3 year manufacturers warranty.




            Page 32

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SUMP AND PUMP
            Pumping Product Range


            SEWAGE PUMPS

            NEWTON SP750 RANGER (P9)
            The Newton SP750 Ranger is a low head and high performance sewage
            pump for the removal of sewage, effluent, waste water and ground water
            with suspended soft solids of up to 50mm.
            The Newton SP750 Ranger is primarily used as the standard pump in our
            Trojan sump systems but can also be used as a stand-alone pump within
            formed concrete sumps and should be used with 63mm pressure rated
            discharge pipe.
            1 year manufacturers warranty.



            NEWTON FLYGT DXG (GRINDER) (P14 & P16)
            The Newton Flygt DXG (Grinder) is a high performance submersible
            grinder pump which cuts solids in sewage into smaller bits that can easily
            pass through the impeller and discharge pipes.
            The Newton Flygt DXG is primarily used as the standard pump in our
            Trojan sump systems but can also be used as a stand-alone pump within
            formed concrete sumps and should be used with 50mm pressure rated
            discharge pipe.
            1 year manufacturers warranty.
            Available in Automatic (P14) or Manual (P16) versions.




            SEWAGE LIFTING STATION

            TROJAN SEWAGE PUMPING SYSTEM (TR1-TR12)
            Newton Trojan systems are specialist packed sewage systems based upon
            a 610mm diameter sump with depth options of 1000mm and 1500mm.
            The Trojan systems are supplied as either single or twin pump systems
            using the Newton 750 Trojan (Vortex) or Newton Flygt DXG (Grinder).
            A hole cutter and 1 x 110mm wall flange is supplied allowing for accurate
            on-site positioning of the invert connection.
            Note: The Trojan System is not supplied with a High Water Level Alarm -
            Alarm and pump control options are available at extra cost.




                                                                                                                                               Page 33

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                       www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SUMP AND PUMP
            Pumping Product Range


            CLEAN/GROUND/EFFLUENT PUMPING SYSTEMS

            TITAN-PRO WHITE (TPW)
            The Newton Titan-Pro White is designed specifically to be used with
            Newton System 500. The adjustable neck allows for the sump to be
            installed at a fixed height relative to the slab so that the connection in
            from the Newton drainage system and the pump discharge line are made
            above the concrete.
            The sump can be used with single pumps, twin pumps and twin pumps
            with twin discharge lines for greater pump efficiency.
            The Titan-Pro White is available with the following pumps: CP250, CP400,
            NP400, NP400W, CP750, NP750.
            The system comprises a sump chamber with 450mm x 450mm recessed
            lid, single or double pumps, internal pipework, one-way valves and the
            Newton PA50 High Water Alarm.
            Chamber dimensions: 805mm high x 650mm wide


            TITAN-PRO GREEN (TPG)
            The Titan-Pro Green is designed for the pumping of ground water or
            surface water where the added features of the Titan-Pro White are not
            required. Ideally suited for receiving connections from rainwater gullies.
            A hole cutter and 1 x 110mm wall flange is supplied allowing for accurate
            on-site positioning of the invert connection.
            The sump can be used with single pumps or twin pumps with a single
            discharge line.
            The Titan-Pro White is available with the following pumps: CP250, CP400,
            NP400, NP400W, CP750, NP750.
            The system comprises a sump chamber with 450mm x 450mm recessed
            lid, single or double pumps, internal pipework, one-way valves and the
            Newton PA50 High Water Alarm.
            Chamber dimensions: 805mm high x 650mm wide


            NEWTON TITAN-2 (T1-T10)
            The Titan-2 pumping system is designed for when a smaller chamber than
            the Titan-Pro is required and is suitable for low volume pumping situations
            within basements or for the pumping of collected surface water from light-
            wells etc.
            The Titan-2 is available with the following pumps: NP150, CP250, CP400,
            NP400, NP400W.
            The system comprises a sump chamber with 450mm x 450mm recessed
            lid, single or double pumps, internal pipework, one-way and shut-off
            valves and the Newton PA50 High Water Alarm.
            Chamber dimensions: 545mm high x 534mm wide

            Page 34

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                       www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SUMP AND PUMP
            Pumping Product Range


            PUMPING ANCILLARY PRODUCTS

            NEWTON CONTROL PANEL-PRO (CP2)
            The Newton Control Panel Pro is a class-leading pump control panel with
            many unique features which has been designed by Newtons to provide
            the ultimate in pump operation and diagnostic capabilities. The panel
            interfaces with Newton Power Converters and telemetry systems and can
            be connected to the house monitoring system.
            The Control Panel PCB is split with two separate circuits, ensuring that
            pumping will continue even if one of the control circuits should fail. This
            effectively means that Newton Control Panel Pro is two control panels in
            one case, offering unrivalled protection.



            NEWTON HIGH WATER LEVEL ALARM (PA50)
            The Newton High Level Water Alarm–PA50 has been designed to detect
            high water levels within pump sump chambers and is included within the
            Newton Titan-Pro and Newton Titan-2 pumping systems. The alarm is
            battery operated and uses a standard 9V PP3 battery.
            The alarm can be programmed to automatic reset or manual reset after
            an alarm occurrence. A mute button to the front face silences the alarm
            once the alarm condition is discovered. A flashing alarm light gives visual
            indication of an alarm condition and this light will continue to show even
            when the alarm sounder is muted.



            NEWTON DIALER (PA5, PA6, PA7)
            The Newton Dialer – PA5 provides enhanced alarm capability to the
            Newton PA50 High Water Level Alarm fitted as part of a Newton Pumping
            System. The PA5 Dialer will contact up to 8 persons by text or speech (or
            both simultaneously) via the standard BT Telephone line to warn of an
            alarm condition with the PA50 Alarm. The Dialer is supplied with a multi-
            core cable that provides signal connections from the PA50 Alarm.
            A 12V power supply is required and this should be ordered with the Dialer
            at purchase depending on whether the PA50 Alarm is used with a system
            that contains a Newton Power Converter:
            If no Newton Power Converter is included within the pumping system, the
            Mains Connector For Dialer is required – Newton Code PA7.
            If the pumping system includes a Newton Power Converter, the Battery
            Connection For Dialer is required – Newton Code PA6.




                                                                                                                                               Page 35

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON SUMP AND PUMP
            Pumping Product Range


            PUMPING ANCILLARY PRODUCTS
            NEWTON 1200w POWER CONVERTER (C1 & C3)
            Battery back up facilities for pumps of 150W and 400W is provided by the
            Newton 1200W Power Converter - C1. The unit receives 12V power from
            a deep cycle leisure battery and converts this into 230V mains power to
            ensure that the Newton Pump continues to operate even during a power
            outage. A two phase charger ensures that the battery is fully charged at all
            times by trickle charging to keep the battery at optimal charge and then by
            boosting up to 20 Amps to quickly re-charge the battery after extended use.
            Purchase Code C1 is for the Power Converter only. Purchase code C3
            includes a 115A/H deep cycle leisure battery, a secure battery box, and the
            power leads for connection to the mains and the battery.
            Additional batteries and link leads can be purchased to increase the volume
            of water that can be pumped during a power failure.




            NEWTON 3000w POWER CONVERTER (C2 & C4)
            The Newton 3000w Power Converter - C2 receives 12V power from a deep
            cycle leisure battery and converts this into 230V mains power to ensure
            that the Newton Pump continues to operate even during a power outage.
            A two phase charger ensures that the battery is fully charged at all times
            by trickle charging to keep the battery at optimal charge, and then by
            boosting up to 20 Amps to quickly re-charge the battery after extended
            use. This 3000W unit is designed to be used with single Newton pumps
            with power outputs of up to 750W only or with dual pumps of 400W to
            750W when switched by one of our Control Panels.
            Purchase Code C2 is for the Power Converter only. Purchase code C4
            includes a 115A/H deep cycle leisure battery, a secure battery box, and
            the power leads for connection to the mains and the battery.
            Additional batteries and link leads can be purchased to increase the volume
            of water that can be pumped during a power failure.




            Page 36

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON MULTI-USE
            Multi-Use Products


            NEWTON MULTI-USE
            System Overview
            The Multi-Use section is home to products that are used within more
            than one of our systems. WaterSeal Tape, for example, can be used with
            System 200, System 400, System 500, System 600 and System 800.
            Highlights include Newton Mesh Tape, which is used with all of our
            meshed membranes to facilitate direct plastering or rendering, and the
            Newton MultiPlug which includes a soft rubber sealing grommet and a
            pin, which when inserted into the plug, expands the fixing to provide a
            better fit within soft or friable substrate.


            NEWTON MESH TAPE (A25)
            Newton Mesh Tape is a self-adhesive sealing tape made of a butyl
            rubber compound with a polypropylene fleece finish. The tape has been
            developed for use with Newton Meshed Membranes where a surface ‘key’
            is required for plastering or rendering over.
            Newton Mesh Tape is the recommended jointing tape for the following
            Newton membranes: Newton 603 Mesh, Newton 803 Newtonite, Newton
            805 Newlath. It can also be used as an overtape to provide a key above
            joints to Newton System 500 meshed waterproofing membranes (Newton
            503 Mesh and Newton 508 Mesh), over joints already sealed with Newton
            WaterSeal Tape, Newton WaterSeal Rope or Newton Overtape.
            Newton Mesh Tape is available in 150mm x 10m rolls.



            NEWTON OVERTAPE (A7, A8, A9)
            Newton Overtape is used to create single sided taped joints as an
            overtape to seal adjacent butted and overlapped membranes, or to seal
            above joins to the membrane created whilst shaping the membrane to fit
            convoluted substrate. Newton Overtape can also be used for the sealing
            of protrusions through the membrane.
            Newton Overtape is available in rolls 150mm x 20m (A7-Black),
            100mm x 20m (A8-Black, A9-White)



            NEWTON WATERSEAL ROPE (A6, A6W)
            Newton WaterSeal Rope is used to form a seal at the overlap of adjacent
            sheets of Newton membranes when neither a flange joint or stud into stud
            joint has been made. A bead of WaterSeal Rope is used for the sealing
            of penetrations through the Newton membranes. WaterSeal Rope is also
            used to create a sealing ring to the base of the Newton NuSeal Plug.
            WaterSeal Rope is supplied in rolls 10mm x 4.75m and is available in
            Black (A6) or White (A6W)



                                                                                                                                               Page 37

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                       www.newton-membranes.co.uk - info@newton-membranes.co.uk
            SYSTEM OVERVIEW
            NEWTON MULTI-USE
            Multi-Use Products


            NEWTON WATERSEAL TAPE (A5, A5W)
            Newton WaterSeal Tape is used to form a seal at the overlap of adjacent
            sheets of Newton membranes.
            WaterSeal tape is placed between the flange of one sheet and the top
            flat surface of the next, or if the studs interlock, it can be used to seal
            between the flat contact area of this type of joint.
            WaterSeal tape is supplied in rolls 30mm x 2mm x 22.5m in Black (A5)
            and White (A5W)




            NEWTON MULTIPLUG (A1)
            Newton MultiPlug has been engineered to give a better fix in questionable
            substrates. It has the added benefit of having a rubber sealing grommet
            supplied with the plug. In very poor substrate, a pin (supplied in bags
            of 100 at extra cost) is inserted into the plug that expands its outer
            circumference by nearly 2mm to tighten the plug into the substrate.
            The Newton MultiPlug is pre-drilled to accept a size 10 (5mm)
            self-tapping screw for the fixing of battens or other dry-lining systems.
            Newton MultiPlugs are recommended in all below ground membrane
            applications except vaulted arches.
            Note: 10mm SDS drill bit required, plugs are 57mm in length.
            Newton MultiPlugs are supplied in bags of 100 (A1)




            NEWTON NUSEAL PLUGS (A2, A3)
            Newton NuSeal Plugs are used to secure Newton System 500 membranes
            to building substrate and to fix battens or tracking systems. Prior to using
            NuSeal plugs, wrap a bead of Newton WaterSeal Rope around the head of
            the plug to form a compression seal.
            NuSeal Plugs are recommended when applying Newton 508 or Newton
            508 Mesh to vaulted arches.
            Note: 11mm SDS drill bit required, plugs are 70mm in length.
            Newton NuSeal Plugs are supplied in bags of 100 in Red (A2) or
            White (A3)




            Page 38

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            Damp Proofing and
            Structural Waterproofing Solutions

            Basement Waterproofing to BS8102 - Existing Basements
            Newton’s market leading basement waterproofing solution Newton System
            500 is ideal for waterproofing existing basements and cellars. It is commonly
            used where conventional ‘tanking’ has failed, and it fully conforms with the
            recommendations within BS8102:2009 Code of Practice for the Protection of
            Below Ground Structures Against Water from the Ground.
            BS8102:2009 recommends that the waterproofing solution is fully
            maintainable and serviceable. Newton System 500 is a cavity drain
            membrane system which works by placing designed and maintainable
            depressurisation voids at known weaknesses in the structure, so that
            problem water is simply captured and diverted out of the property.                                               Newton System 500 has been installed
                                                                                                                             in the Grade I Listed Royal Courts of
            Newton System 500 is ideal for application to listed and historic buildings                                      Justice, London
            as it is deemed ‘reversible’ - a requirement of conservation authorities.


            Basement Waterproofing to BS8102 - New Build Basements
            Newton Waterproofing Systems provide the designer with solutions for all
            aspects of the waterproofing of the structure, from the water bars within
            the construction joints to the sealing of the deck above. Systems can be
            used in isolation or can be combined as recommended by BS8102:2009
            to give greater assurance of waterproofing performance. BS8102:2009
            defines three types of waterproofing and Newton Systems are available for
            all three types and combinations of all three types:
            Type A - (barrier) protection: Newton System 100, Newton System 200,
            Newton System 400
            Type B - (structurally integral) protection: Newton System 300                                                   Newton offer complete waterproofing
            Type C - (drained) protection: Newton System 500, Newton System 400                                              solutions for new build basements
            Combination system can be provided for Type A + Type B, Type A + Type C
            and Type B + Type C



            Damp Proofing Listed Buildings
            When dealing with listed and historic buildings, it is fundamentally
            important to maintain the structural and aesthetic integrity of the
            building. Newton damp proof membranes can be sympathetically applied
            with little or no preparation required. The damp proof membrane provides
            an impervious separation barrier between the damp surface and the new
            internal wall, so moisture is prevented from affecting the internal finishes.
            Newton wateproofing systems have been used in many listed and historic
            buildings including: the British Museum, the Houses of Parliament, Windsor
            Castle, St Georges Hall - Liverpool, the Royal York Hotel - Bath, Wallis House
            - Middlesex, Limerick Court House - Ireland and Menin Gate - Ypres.                                              Newton 805 Newlath has been used to
            John Newton & Company were the original innovators in damp proofing,                                             damp proof walls in Windsor Castle
            having introduced a damp proof membrane in 1937. Our leading damp
            proof membrane, Newton 805 Newlath, remains the original meshed
            membrane, and over two million metres have been installed in the
            UK alone.


                                                                                                                                                        Page 39

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
            Damp Proofing and
            Structural Waterproofing Solutions

            Waterproofing Concrete Structures
            Newton FlexProof is a multi-faceted single component flexible
            waterproofing system which can be applied to reinforced concrete in a
            one-coat application without the need for primers. It outperforms its rivals
            by having the capacity to be installed in temperatures below 5º C.
            FlexProof can be used to waterproof podium decks and balconies,
            construction/movement joints, retaining walls and wet rooms. It is
            capable of handling severe building movements and deformations.
            FlexProof contains no solvents and as such can be applied internally as
                                                                                                                             Newton FlexProof is rainproof in minutes
            well as externally.
                                                                                                                             and can be applied in sub-zero temperatures


            Upgrading the Thermal Performance of Buildings
            Newton Diathonite Insulation Plaster has a high thermal capacity due to
            the presence of cork. It is made from natural components and hydraulic
            lime. In addition, Diathonite offers soundproofing benefits and its
            application to structures eliminates cold bridging and provides a robust
            and high quality finish.
            Diathonite applied externally can upgrade the building’s thermal
            performance to meet building regulation standards thus negating the
            need to insulate internally, saving time and space.
            The application of Diathonite Insulation Plaster to a building also                                             Newton Diathonite Insulation Plaster is
            saves on energy costs, keeping the structure cool in summer and warm                                            an eco thermal plaster with excellent
            in winter.                                                                                                      insulation and acoustic properties



            Newton Registered Installers
            Newton Specialist Basement Contractors (NSBC) are a nationwide group
            of professional waterproofing and damp proofing contractors who provide
            the best quality products, design and installation available in all aspects
            of basement waterproofing and damp proofing.
            NSBCs can offer peace of mind to the designer and the client by taking full
            design liability on the project, and in addition they must be able to offer “PI”
            (Professional Indemnity) on waterproofing design and offer independent
            insured guarantees for the installation. They are regularly trained and
            assessed by John Newton & Company, and adhere to very strict criteria. The
            requirements of BS8102:2009 Code of Practice for the Protection of Below
            Ground Structures Against Water from the Ground asks for a waterproofing                                            Newton Specialist Basement Contractors
            specialist to be included as an integral part of the design team to ensure                                          offer guaranteed waterproofing solutions
            that an integrated waterproofing solution is realised.
            For a list of Newton Specialist Basement Contractors in your area, please
            contact John Newton & Company.


                       For many more case studies, please see www.newton-membranes.co.uk.
                  For further information, free technical advice or additional copies of this catalogue
                         please ring 020 7237 1217 or e-mail info@newton-membranes.co.uk
            Page 40

                            © John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
J o h n N e w to n Ltd I s s u e 0 1 M ay 0 8 w w w. n e w to n - m e m b ra n e s. co. u k i n f o @ n e w to n - m e m b ra n e s. co. u k
                                      www.newton-membranes.co.uk - info@newton-membranes.co.uk
                         Protecting buildings, since 1848


        NEWTON WATERPROOFING SYSTEMS
                Innovators In Structural Waterproofing
            And Damp Proofing Products For Over 160 Years
John Newton & Co Ltd, Est 1848, is the UK’s leading independent supplier of structural
waterproofing systems, water control and drainage products. Newtons offer the best
available, BBA certificated solutions for waterproofing and damp proofing applications
in new-build and refurbishment projects. Our range of structural waterproofing
systems, including cementitious products, deck and roofing membranes and liquid
applied floor coatings enable us to offer full waterproofing solutions for a wide variety
of projects.

Newton Waterproofing Systems control and remove unwanted water from leaking
tunnels and underpasses, railway arches, wet basements, flooded cellars and
damp vaults to make warm habitable areas or areas suitable for dry storage in both
commercial and domestic projects. Newton’s portfolio of concrete waterproofing
products gives specifiers the tools to provide full building envelope protection to
reinforced concrete structures.

Newton structural waterproofing and damp proofing products offer the highest
level of protection. Our team of technical experts can design and modify technical
drawings in all formats and design a waterproofing solution best suited to your
requirements.

Newton Specialist Basement Contractors (NSBC) can offer a fully guaranteed design
and installation of our systems and “PI” (Professional Indemnity) on waterproofing
design and offer independent insured guarantees for the installation. Please contact
us for a list of NSBCs in your area.


                      John Newton & Company Ltd.
               12 Verney Road, London SE16 3DH
                    Phone: 020 7237 1217
   www.newton-membranes.co.uk info@newton-membranes.co.uk

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:39
posted:2/22/2012
language:English
pages:42
Description: Newton System 100 is a comprehensive portfolio of cementitious products which have been introduced into our structural waterproofing range to complement and complete our basement waterproofing designs in areas where the Newton System 500 would not be suitable.