CX3 RG659 Installation

Document Sample
CX3 RG659 Installation Powered By Docstoc
					Corning
           1
Cabelcon
To begin with – we need some tools…

Cabelcon Rotary Stripper


                                                 Cable cutter




                                         Mounting tool



                                                Please read the
                                                  instructions
                                                before using the
                                                     tools!
     Rubber tool      Compression tool

           Corning
                                                                   2
           Cabelcon
Let’s start to work…




                        First step is to cut
                       your cable using a
                       proper cable cutter.




        Corning
                                               3
        Cabelcon
Strip your cable…


                      Insert the cable into
                      the cable stripper as
                            shown…
                    Attention: Please make sure to adjust
                    the tool blades for your cable dimensions
                    before using it for the first time! Please
                    read instructions supplied with the tool.

                          Screws for adjustment of blades
                                     Hex tool for adjustment




        Corning
                                                                 4
        Cabelcon
Strip your cable…


                       Turn the stripper
                    clockwise 4-5 times…




        Corning
                                           5
        Cabelcon
Strip your cable…



                    - and pull to remove
                        the scraps…




        Corning
                                           6
        Cabelcon
Strip your cable…



                                     Optional:
                            You can check the stripping
                            dimensions against the guide
                            printed on the connectors

   6,5 + 6,5 mm (¼” + ¼”)




        Corning
                                                           7
        Cabelcon
Prepare your cable…

                      Fold exposed braid over
                      the jacket.
                      Leave the inner foil
                      attached to the dielectric
                      and make sure that the
                      foil is undamaged and
                      smooth.


                      For ”Quad shield”, ”Tri
                      shield” and ”Super shield”
                      cables: Remove the outer
                      braid and foil only. Fold
                      back the inner braid.



       Corning
                                                   8
       Cabelcon
Mount the connector…


                  Use of the Rubber Tool will ensure
                  an excellent grip on the cable!




                                  * Press the front part of the
                                  connector (with the built-in
                                  ”tool”) against the cable and
                                  turn it slowly to prepare the foil
                                  to enter into the connector.
                                  (* Optional operation – normally not
                                  necessary if Corning Cabelcon’s Rotary
                                  Cable Stripper has been used)




       Corning
                                                                           9
       Cabelcon
Mount the connector…

                                  Push the connector over
                                  the foil and allow the
                                  support mandrel to slide
                                  between the foil and
                                  braid…




        A mounting tool can be
        used to ensure a better
        grip on the connector…



       Corning
                                                             10
       Cabelcon
Mount the connector…

                   Press and turn until the
                   dielectric is flush with the
                   support mandrel face




       Corning
                                                  11
       Cabelcon
Compress the connector…

                            1) Insert your connector/cable
                            into the tool with the tool handle
                            in open position…



                                                    Click!


                  2) Apply a downward
                  pressure on the cable
                  to allow the split jaws
                  to secure the cable…
       Corning
                                                                 12
       Cabelcon
Compress the connector…


                                                     Before
                                                     compression




                                                     After
                                                     compression




- and close the tool handle completely insuring the connector
sleeve is fully compressed (white plastic is invisible).



           Corning
                                                                13
           Cabelcon
Take out the connector…


                     Open the tool - press the
                     outside split-jaw tabs and pull
                     out the connector assembly…




       Corning
                                                       14
       Cabelcon
Compression completed


                  The finest connection
                        available!




       Corning
                                          15
       Cabelcon
 More tools available…

Other types of tools are available. A few examples:

                                        Universal tool for
                                        RG6/59 and RG11




  Corning Cabelcon universal CX3
        compression tools



                                       Various installation tools




     Please checkout our website www.cabelcon.dk for more information
               Corning
                                                                        16
               Cabelcon
Finally some good advice…

                       In order to avoid decreased network
                       performance, we recommend the use
                       of a torque wrench to ensure proper
                       tightening of your connectors.


                  1.



                                              2.

       Corning
                                                             17
       Cabelcon
           January 2008

Corning
                          18
Cabelcon

				
DOCUMENT INFO
Shared By:
Categories:
Tags:
Stats:
views:27
posted:2/11/2012
language:
pages:18