Back to Back Order in Order Managment

Report as inappropriate Your report has been received

Description

Back to Back Order in Order Managment document sample

Shared by: nea53723

Tags

Stats

views:: 31
posted:: 1/19/2012
language:: English
pages:: 32

Public Domain

/ 32 Download or Print

Document Sample

INTRODUCTION

INTRODUCTION
About This Catalog
General Information
Product Numbering System
Nomenclature
Finishing Codes
Other Newton Catalogs
eNewton
Abbreviations
Feedback

NEWTON INSTRUMENT COMPANY, INC.
Butner, NC

Section I
INTRODUCTION
16B

N E W TON INSTRUMENT COMPA N Y
Butner, NC

I-1
ABOUT THIS CATALOG

Welcome to Newton’s latest Cable Management Products and Enclosures Catalog. You will notice some
changes from past versions, all of which are intended to make this catalog much easier to use. The most
significant changes are as follows:

1. A ten-character Ordering Number is provided for each product. Please use the product’s Order-
ing Number on your purchase order to ensure accurate and efficient order processing.

2. The Figure Number, used for catalog indexing, has been expanded to six characters; these are the
first six characters of the ten-character Ordering Number. Characters seven and eight of the Or-
dering Number are referred to as the Dash Number and characters nine and ten define the item’s
Finish Code. Please refer to “Newton Numbering System, Nomenclature, Finish Codes” (Page iii)
for additional details.

3. A Standard Finish Code has been defined for each product. Where the Finish Code can be user-
defined, XX is shown in catalog information for characters nine and ten of the Ordering Number. A
list of commonly used Finish codes is provided within “Newton Numbering System, Nomenclature,
Finish Codes” (Page iv). Items that are available with only a specific Finish Code include a pre-
defined Finish Code in characters nine and ten. If a product’s Finish Code is not specified by your
purchase order, Newton will process the order using that product’s Standard Finish Code.

4. Stock List information, where applicable, includes component Description and Quantity. All items
defined by the Stock List are included with the Ordering Number indicated. Except for hardware
items (such as bolts and washers), all items within the Stock List are provided with the Standard
Finish Code if not user-defined.

5. Items shown pictorially or described to indicate how a product is used that are not included in the
Stock List are not included with the item’s Ordering Number.

6. Selected hardware items (such as bolts, nuts and washers) are available only in a packaged quantity,
or multiples thereof, as indicated by the item’s Stock List information.

7. Products are categorized and indexed by product type and functional use, not in numeric sequence
as in former versions of this catalog. Sub-indexes are now included for some product categories. A
numeric index is included at the back of this catalog for your convenience.

8. To provide the user with an overview of Newton’s overall product offering, abbreviated informa-
tion about selected products from other Newton catalogs is included, with on details how to obtain
that product’s complete catalog.

9. To shorten descriptions, Abbreviations and Acronyms are used within catalog information; a list of
Abbreviations and Acronyms is included within the Introduction section of this catalog (Page ix).

10. All dimensions included are nominal, without manufacturing tolerances, and are for reference only.
Unless otherwise indicated, dimensions are in inches.

N E W TON INSTRUMENT COMPA N Y
Butner, NC

I-2
GENERAL INFORMATION
ORDERING
Each Newton product (item, assembly, or kit) is identified in catalog information by a ten-character Ordering Number,
which may include a variable Dash Number (characters seven and eight). For example, within Ordering Number
00102110XX, the Dash Number (10) represents a dimension, specification or functional difference and should be
selected carefully. Characters nine and ten within the Ordering Number define the product’s Finish Code. Where the
Finish Code can be user-defined, characters nine and ten of the Ordering Number are shown in catalog information as
XX. If no Finish Code is specified by the purchase order, Newton’s Standard Finish Code for that product will be
provided.

When a product is ordered using Newton’s Ordering Number, all parts shown on that product’s Stock List are included
with the product. To describe a product’s use, pictorial or other information may refer to items that are not included in the
Ordering Number’s stock list. Refer to “Newton Part Numbering Nomenclature, Finish Codes” for additional detail.

Delivery requirements should be specified on the purchase order. Many of your emergency requirements can be shipped
immediately from our inventory.

STANDARD PAYMENT TERMS
NET 30 from Invoice Date. Prices, specifications and other information are subject to change without notice. VISA,
MASTERCARD, and AMERICAN EXPRESS accepted.

MINIMUM ORDER AMOUNT
$100

CUSTOMER RETURN POLICY
It is Newton Instrument Company's policy to provide complete customer satisfaction. In the event that shipped goods need
to be returned to Newton Instrument Company, please refer to the guidelines shown below:

The Returned Goods Authorization (RGA) number must accompany all return shipments in order for us to ensure proper
credit to our customers. Please contact your Customer Service Representative at 919-575-6426 or Fax your request to
919-575-4708 to obtain an RGA number.

All returned material must be packaged in such a manner as to prevent transit damage.
Items that need to be repainted/replated will incur an additional 10% charge.
Items that need to be repackaged will incur an additional 10% charge.
Items received damaged and which cannot be reprocessed by Newton Instrument Company
will be scrapped and the customer notified that no credit will be issued.

Material returned due to Newton Instrument Company error (i.e. Manufacturing defects or wrong part, etc.) may be
returned freight collect with no restocking charge. Material returned due to customer error will be subject to the follow-
ing restocking charges:

Make-to-stock items, 20%,
Make-to-order items and non-catalog items which can be resold, 30%.

All shipments should be made prepaid to Newton Instrument Company. Freight charges on all returns subject to a restock-
ing charge will be the responsibility of the customer. Parts modified or made to customer specifications, including non-

N E W TON INSTRUMENT COMPA N Y
Butner, NC

I-3
GENERAL INFORMATION
stock paint finishes and distribution frames are made to order and not-returnable products. If Newton product is received
damaged due to freight handling, please contact and file a freight damage claim with the carrier. Newton Instru-
ment Company will assist with providing a replacement order that will include billing for replacement parts and freight.
Credit for the return will be issued after the material has been received and inspected by Newton Instrument Company.

Customers are requested to wait until they receive the credit memo before deducting it from the payment of future in-
voices.

CUSTOMER FREIGHT OPTIONS
Shipments are made F.O.B. Butner, North Carolina via one of the following options:

Third Party Billing - carrier chosen by customer. Customers can specify the carrier and have freight charges
billed directly to the customer by providing the Newton customer service representative with: The customer's
account number with the specified carrier and the customer's billing address for freight charges, if it is different
from the product billing address.

Freight Collect - carrier chosen by customer. Customers can specify the carrier and request a freight collect
shipment requiring the customer to give the carrier a check upon delivery or provide the account number with the
carrier.

Newton Prepaid Freight - carrier chosen by Newton Customers can have Newton pay freight charges to the
carrier and have freight cost added to the product invoice. Newton offers this service without an additional
handling charge provided the customer agrees to the following conditions:

Carrier is specified by Newton. We have contractual obligations
with selected carriers to minimize shipping cost,
Customer agrees to pay Newton all freight charges appearing on
product invoices without requiring additional freight cost documentation,
Customer agrees to pay Newton for freight costs associated with an order shipment
but not contained in the initial product invoice. Such charges may result when
specific freight charges from the carrier are not available at time of product
invoicing. An example is additional charges from the carrier for inside delivery
service required by the customer,
Agreement to these conditions is implied when customer specifies prepaid freight
with an order to Newton Instrument Company. These accepted conditions
supersede any statements in customer purchase orders restricting the obligation
to pay freight charges appearing on Newton invoices or requiring additional freight
cost documentation from Newton,
Newton Instrument Company reserves the right to withdraw the prepaid freight
option at any time.

When damage is caused by the freight carrier, the customer is responsible for filing freight claims with the carrier.

ORDER CANCELLATIONS
Orders are subject to cancellation only by mutual agreement.

SPECIAL PACKAGING
A material and labor charge is made for special packaging requirements.

N E W TON INSTRUMENT COMPA N Y
Butner, NC

I-4
PRODUCT NUMBERING SYSTEM, NOMENCLATURE, FINISHING CODES
Each Newton item, assembly, or kit is identified in catalog information by a ten-character Ordering Num-
ber. Use of the full ten-character Ordering Number, along with the item’s description, is preferred when
ordering.

The ten characters of the Newton catalog numbering system are defined below (NNNNNNDDXX is used
for descriptive purposes only).

NNNNNN DD XX

XX = Finish Code
DD = Dash Number
NNNNNN = Figure Number

Figure Number: a six-character abbreviation of the full ten-character Ordering Number: used for indexing in
printed or electronic documentation; may include a Dash Number(s), which defines a variation within the Figure
Number (refer to Dash Number description below).
Dash Number: (seventh and eighth characters = number from 00 to 99): represents a dimensional, functional or
specification difference within an Ordering Number. For example, within Ordering Number 00102110XX, the
Dash Number (10) represents a dimensional difference, defining a specific height from those available.
Finish Code: (ninth and tenth characters): defines that no finish is applicable, that the item has a Plated or Painted
Finish, or the item is thermoplastic. The Finish Code may be numeric, alphabetic, or alpha-numeric. Refer to the
Finish Code listing below for commonly used Finish Codes for metal items; Finish Codes used for thermoplastic
Fiber Cable Management items are separately defined.
Ordering: When ordering by Newton’s ten-character Ordering Number, provision for defining the Finish Code is
automatically included. Where the Finish Code can be user-specified, characters nine and ten of the Ordering
Number are shown in catalog information as XX, allowing the user to replace XX (characters nine and ten) with the
desired Finish Code. The desired Finish Code may also be defined in writing by the customer order. Items that
include a pre-defined Finish Code (other than XX) are available with only that pre-defined finish. If the Ordering
Number contains XX as the ninth and tenth characters and the purchase order does not specify a finish within the
Ordering Number or in writing, Newton’s Standard Finish Code for that item will be provided.
All of the parts included in an item’s stock list (or equivalent) are included with the item / assembly / kit Ordering
Number. Where the Finish Code for an item is defined within the stock list, that item is provided with the defined
finish.
Finish Code: The following are the most commonly used Finish Codes (for metal); others are available on
request.
XX = 00 = No finish or a finish is not applicable

Plated Finish (XX = ) Painted Finish (XX = )

10 = Zinc Plated and Gold Chromate 30 TE (Telephone Equipment) Gray
=
11 = Zinc Plated and Clear Chromate 31 ADC Gray
=
12 = Stainless Steel 45 Midnight Black Wrinkle (Powder)
=
13 = Copper / Copper Plated 50 Maple Brown
=
14 = Clear Chromate on Aluminum 64 Blue Wrinkle (Powder)
=
20 = Galvanized 70 = AE. Beige
23 = Cleaned Unpainted Aluminum 73 = Sahara Beige Wrinkle (Powder)

N E W TON INSTRUMENT COMPA N Y
Butner, NC

I-5
OTHER NEWTON CATALOGS

Newton is continually adding new products and applications to its diverse product line. Product
information is available in the catalogs listed below and on-line via our web site, www.enewton.com.

CATALOG TITLE

Auxiliary Framing & Accessories
Cable Rack & Accessories
Hardware & Grounding Bars
Equipment Racks & Accessories
Distribution Frames
Cabinets & Accessories
Fiber Cable Management System
Seismic Products

Catalog Order forms are available within this catalog. Please communicate with your Newton Customer
Sales Representative should you desire any of the above information.

Phone: 919-575-6426 Fax: 919-575-4708.

eNEWTON WEB SITE

The information from this and other Newton catalogs is available on-line at Newton’s web site. Product
Selection assistance, on-line quote request creation and submittal, Product cross-reference, instant product
pricing and availability, real-time order and shipment tracking and status can all be found on our web site
www.enewton.com.

N E W TON INSTRUMENT COMPA N Y
Butner, NC

I-6
ABBREVIATIONS / ACRONYMS
A FR = Framing
A or Amp = Ampere Frame = Framing
AC = Alternating Current Ft or ‘ = Feet / Foot
Adj = Adjustable FW = Floor / Wall
ANSI = American National Standards Institute
Assy = Assembly G
Aux = Auxiliary GA or Ga = Gauge
AWG = American Wire Gauge Gnd = Ground
Grd = Guard
B GR or G.R. = Guard Rail
BOC = Bell Operating Company GR = Generic Requirement (Bellcore)
Brkt = Bracket
H
C H = Height
C = Centigrade Hdw or Hdwr = Hardware
Cab = Cabinet Hex = Hexagonal
CEV = Controlled Environmental Vault HF = High Frequency
Chan = Channel HHCS = Hex Head Cap Screw
CO = Central Office HHMS = Hex Head Machine Screw
CRS = Cold Rolled Steel Horiz = Horizontal
CSA = Canadian Standards Association HRS = Hot Rolled Steel
Ctr = Center Ht = Height
Hz = Hertz
D
D = Depth I
Deg = Degree ID = Inside Diameter
Det = Detail IDF = Intermediate Distributing Frame
DF = Distributing Frame In or in or “ = Inch / Inches
Dia = Diameter Int = Internal
Dim = Dimension
Diff = Different J
DR = Drilled K = Kilo
Ds or DS = Double-sided
DSD = Double Side Drilled L
DSX = Digital Signal Cross-connect L = Length
LAN = Local Area Network
E lb / lbs = Pound / Pounds
EIA = Electronic Industries Association LDR = Ladder
EMC = Electromagnetic Compatibility LED = Light Emitting Diode
EMI / RFI = Electromagnetic Interference / LH = Left Hand
Radio Frequency Interference LGX = Lightguide Cross-connect
ESD = Electrostatic Discharge
ETSI = European Telecommunications M
Standards Institute M = Metric
Exp = Expansion Mach = Machine
MAN = Metropolitan Area Network
F Matl = Material
F = Fahrenheit MDF = Main Distribution Frame
FHMS = Flat Head Machine Screw mm or MM = millimeter
FL = Floor Mtg = Mounting

N E W TON INSTRUMENT COMPA N Y
Butner, NC

I-7
NEWTON FEEDBACK FORM

Newton is interested in your feedback about this catalog and uses it as one source to improve the
information provided to our customers. Please reference Figure Number(s) / page number(s) when
applicable. Your feedback is certainly appreciated.

From (Name):

Company: Telephone:

Feedback:

FAX this completed form to: 919-575-4708, ATTN.: Director of Marketing

Mail this completed form to:

Newton Instrument Company, Inc.
111 East A Street
Butner, NC 27509-2426
ATTN.: Marketing Coordinator

EMAIL feedback, using the above format, to: info@newtoninst.com.

N E W TON INSTRUMENT COMPA N Y
Butner, NC

I-8
DISTRIBUTION FRAMES

DISTRIBUTION FRAMES

NEWTON INSTRUMENT COMPANY , INC.
Butner, NC

Section E
Distribution Frames

THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF NEWTON INSTRUMENT COMPANY N E W TON INSTRUMENT COMPA N Y
INC. ANY REPRODUCTION IN PART OR WHOLE WITH OUT
THE WRITTEN PERMISSION OF NEWTON INSTRUMENT
Butner, NC
COMPANY IS PROHIBITED.

E-1
005005 THRU
UNIVERSAL DISTRIBUTING FRAME, DOUBLE SIDED
005016

* B & E DIMENSIONS ARE OVERALL AND
HORIZONTAL SIDE LENGTHS OF SHELVES
INCLUDING PROTECTOR BAR OR TERMINAL
BLOCK SWIVEL CLIPS WHICH ARE NOT SHOWN.

*
B
*
E

F
NO. OF
SHELVES @ 8"

11 15

8
3-15/16 D
3-9/16 3-9/16
G C
5 VERTICALS SHOWN

THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF NEWTON INSTRUMENT COMPANY NEWTON INSTRUMENT COMPANY
INC. ANY REPRODUCTION IN PART OR WHOLE WITH OUT
THE WRITTEN PERMISSION OF NEWTON INSTRUMENT
Butner, NC
COMPANY IS PROHIBITED.

E-2
005005 THRU
UNIVERSAL DISTRIBUTING FRAME, DOUBLE SIDED
005016

FIGURE NO. HEIGHT SHELF WIDTH GUARD RAIL D E F NO. OF HORIZ.
A B WIDTH C SHELVES
005005 8'-0" 20-1/2" 30-1/2" - 36-1/2" 15-3/4" - 18-3/4" 10-3/4" 76" 10
005006 8'-0" 26-1/2" 36-1/2" - 42-1/2" 19-3/4" - 22-3/4" 14-3/4" 76" 10
005007 8'-0" 32-1/2" 42-1/2" - 48-1/2" 23-3/4" - 26-3/4" 18-3/4" 76" 10
005008 9'-0" 20-1/2" 30-1/2" - 36-1/2" 15-3/4" - 18-3/4" 10-3/4" 92" 11
005009 9'-0" 26-1/2" 36-1/2" - 42-1/2" 19-3/4" - 22-3/4" 14-3/4" 92" 11
005010 9'-0" 32-1/2" 42-1/2" - 48-1/2" 23-3/4" - 26-3/4" 18-3/4" 92" 11
005011 11'-6" 20-1/2" 30-1/2" - 36-1/2" 15-3/4" - 18-3/4" 10-3/4" 124" 15
005012 11'-6" 26-1/2" 36-1/2" - 42-1/2" 19-3/4" - 22-3/4" 14-3/4" 124" 15
005013 11'-6" 32-1/2" 42-1/2" - 48-1/2" 23-3/4" - 26-3/4" 18-3/4" 124" 15
005014 11'-8" 20-1/2" 30-1/2" - 36-1/2" 15-3/4" - 18-3/4" 10-3/4" 124" 15
005015 11'-8" 26-1/2" 36-1/2" - 42-1/2" 19-3/4" - 22-3/4" 14-3/4" 124" 15
005016 11'-8" 32-1/2" 42-1/2" - 48-1/2" 23-3/4" - 26-3/4" 18-3/4" 124" 15

DASH NO. DESCRIPTION G
01 GROUP OF 1 VERT. 7-7/8"
02 GROUP OF 2 VERT. 15-7/8"
03 GROUP OF 3 VERT. 23-7/8" 10 DIGIT ORDERING NUMBER
04 GROUP OF 4 VERT. 31-7/8" FIGURE NO. + DASH NO. + FINISH CODE = PART NUMBER
05 GROUP OF 5 VERT. 39-7/8" 005005 + 03 + 30 =0050050330 (8’ DISTRIBUTION FRAME WITH A 20-1/2”
06 GROUP OF 6 VERT. 47-7/8" SHELF, A GROUP OF 3, TE GRAY FINISH)
07 GROUP OF 7 VERT. 55-7/8"
08 GROUP OF 8 VERT. 63-7/8" CUSTOMER MUST SPECIFY “MDF” OR “IDF” OR A COMBINATION OF THE
09 GROUP OF 9 VERT. 71-7/8" TWO FOR EACH FRAME. SEE NOTE 3 & 4.
10 GROUP OF 10 VERT. 79-7/8"
11 JUNCTIONING KIT --
12 LEFT END GUARD --
13 RIGHT END GUARD --
30 IDF VERTICAL --
40 MDF VERTICAL --

FEATURES FOR 005005 - 005016:
• SAME BASIC VERTICAL DESIGN FOR MDF AND IDF FRAMES.
• SWIVEL TYPE MTG. BRACKET ACCEPTS END OR CENTER MOUNT TERMINAL BLOCK.
• WELDED ASSEMBLY WITH BOLT-ON FRAME COMPONENTS AND ACCESSORIES.
• UNIVERSAL TERMINAL BLOCK MOUNTING BRACKETS AND PROTECTOR BARS.
• MDF AND IDF VERTICALS CAN BE INTERMIXED IN A CONTINUOUS FRAME LINE-UP.

NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

2. FRAMES SUPPLIED WITH ADJUSTABLE GUARD RAILS, GROUND BAR, AND GUIDE LOOPS. A COMPLETE SET OF
ASSEMBLY PRINTS IS SHIPPED WITH EACH FRAME.

3. CUSTOMER SHOULD SPECIFY IDF VERTICALS WHEN USING TERMINAL BLOCKS ON VERTICAL AND HORIZONTAL SIDES
OF FRAME. IDF VERTICAL COMES EQUIPPED WITH NEWTON UNIVERSAL SWIVEL TYPE TERMINAL BLOCK MOUNTING
BRACKET.

4. CUSTOMER SHOULD SPECIFY MDF VERTICALS WHEN USING PROTECTOR/CONNECTORS ON VERTICAL SIDE OF
FRAME AND TERMINAL BLOCK ON HORIZONTAL SIDE OF FRAME. MDF VERTICAL COMES EQUIPPED WITH NEWTON
UNIVERSAL PROTECTOR BAR.

5. FOR APPLICATIONS REQUIRING MORE THAN TEN VERTICALS, ORDER TWO FRAMES THAT TOTAL THE REQUIRED
NUMBER. (FOR 19 VERTICALS, AS AN EXAMPLE, ORDER ONE EACH 00500509XX AND ONE EACH 00500510XX.)

E-3
005017 THRu
UNIVERSAL DISTRIBUTING FRAME, SINGLE SIDED
005024

* B DIMENSION IS LENGTH OF SHELF
INCLUDING PROTECTOR BAR OR
TERMINAL BLOCK SWIVEL CLIPS WHICH
ARE NOT SHOWN.

END GUARD

A
NO. OF
SHELVES@ 8"

10
6

8 C
3-15/16 1/8
3-9/16
3-9/16
F
5 VERTICALS SHOWN

THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF NEWTON INSTRuMENT COMPANY NEWTON INSTRUMENT COMPANY
INC. ANY REPRODuCTION IN PART OR WHOLE WITH OuT
THE WRITTEN PERMISSION OF NEWTON INSTRuMENT
Butner, NC
COMPANY IS PROHIBITED.

E-
005017 THRu
UNIVERSAL DISTRIBUTING FRAME, SINGLE SIDED
005024

part number height shelf width guard rail width no. of horiz.
A B C D shelves

005017 8’-0” 5-1/2” 12” - 15” 84” 11
005018 8’-0” 8-1/2” 15” - 18” 84” 11
Ordering Table

005019 9’-0” 5-1/2” 12” - 15” 92” 12
005020 9’-0” 8-1/2” 15” - 18” 92” 12
005021 11’-6” 5-1/2” 12” - 15” 124” 16
005022 11’-6” 8-1/2” 15” - 18” 124” 16
005023 11’-8” 5-1/2” 12” - 15” 124” 16
005024 11’-8” 8-1/2” 15” - 18” 124” 16

dash number description F 10 DIGIT ORDERING NUMBER
01 Group of 1 vert. 7-7/8”
FIGuRE NO. + DASH NO. + FINISH CODE = PART NuMBER
005017 + 03 + 30 =0050170330 (8’ DISTRIBuTION FRAME WITH A 5-1/2”
02 Group of 2 vert. 15-7/8”
SHELF, A GROuP OF 3, TE GRAY FINISH)
03 Group of 3 vert. 23-7/8”
04 Group of 4 vert. 31-7/8” CUSTOMER MUST SPECIFY “MDF” OR “IDF” OR A COMBINATION OF THE
05 Group of 5 vert. 39-7/8” TWO FOR EACH FRAME. SEE NOTE 3 & 4.
06 Group of 6 vert. 47-7/8”
07 Group of 7 vert. 55-7/8”
08 Group of 8 vert. 63-7/8”
09 Group of 9 vert. 71-7/8”
10 Group of 10 vert. 79-7/8”
11 Junction kit --
12 Left End Guard --
13 Right End Guard --
30 IDF vertical --
40 MDF vertical --

NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

2. FRAMES SuPPLIED WITH ADJuSTABLE GuARD RAILS AND GuIDE LOOPS. A COMPLETE SET OF ASSEMBLY PRINTS IS
SHIPPED WITH EACH FRAME.

3. CuSTOMER SHOuLD SPECIFY IDF vERTICALS WHEN uSING TERMINAL BLOCkS ON vERTICAL OF FRAME. IDF vERTICAL
COMES EquIPPED WITH NEWTON uNIvERSAL SWIvEL TYPE TERMINAL BLOCk MOuNTING BRACkET.

4. CuSTOMER SHOuLD SPECIFY MDF vERTICALS WHEN uSING PROTECTOR/CONNECTORS ON vERTICAL SIDE OF
FRAME. MDF vERTICAL COMES EquIPPED WITH NEWTON uNIvERSAL PROTECTOR BAR.

5. FOR APPLICATIONS REquIRING MORE THAN TEN vERTICALS, ORDER TWO FRAMES THAT TOTAL THE REquIRED
NuMBER. (FOR 19 vERTICALS, AS AN EXAMPLE, ORDER ONE EACH 00500509XX AND ONE EACH 00500510XX.)

E-
005025 THRU
UNIVERSAL DISTRIBUTING FRAME, SINGLE SIDED
005032

* B DIMENSION IS LENGTH OF SHELF
INCLUDING PROTECTOR BAR OR
TERMINAL BLOCK SWIVEL CLIPS WHICH
ARE NOT SHOWN.

END GUARD 3/4

NO. OF D
SHELVES@ 8"
A

10
6

C
3-15/16 1/8
3-9/16 3-15/16
F

THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF NEWTON INSTRUMENT COMPANY NEWTON INSTRUMENT COMPANY
INC. ANY REPRODUCTION IN PART OR WHOLE WITH OUT
THE WRITTEN PERMISSION OF NEWTON INSTRUMENT
Butner, NC
COMPANY IS PROHIBITED.

E-6
005025 THRU
UNIVERSAL DISTRIBUTING FRAME, SINGLE SIDED
005032

FIGURE NO. HEIGHT SHELF WIDTH GUARD RAIL D NO. OF HORIZ.
A B WIDTH C SHELVES
005025 6'-0" 9" 13" - 16" 60" 8
005026 6'-0" 14" 19" - 22" 60" 8
005027 7'-0" 9" 13" - 16" 68" 9
005028 7'-0" 14" 19" - 22" 68" 9
005029 8'-0" 9" 13" - 16" 84" 11
005030 8'-0" 14" 19" - 22" 84" 11
005031 9'-0" 9" 13" - 16" 92" 12
005032 9'-0" 14" 19" - 22" 92" 12

DASH NO. DESCRIPTION F
01 GROUP OF 1 VERT. 7-7/8"
02 GROUP OF 2 VERT. 15-7/8"
03 GROUP OF 3 VERT. 23-7/8"
04 GROUP OF 4 VERT. 31-7/8"
05 GROUP OF 5 VERT. 39-7/8" 10 DIGIT ORDERING NUMBER
06 GROUP OF 6 VERT. 47-7/8" FIGURE NO. + DASH NO. + FINISH CODE = PART NUMBER
07 GROUP OF 7 VERT. 55-7/8" 005025 + 03 + 30 =0050250330 (6’ DISTRIBUTION FRAME WITH A 9” SHELF,
08 GROUP OF 8 VERT. 63-7/8" A GROUP OF 3, TE GRAY FINISH)
09 GROUP OF 9 VERT. 71-7/8"
10 GROUP OF 10 VERT. 79-7/8" CUSTOMER MUST SPECIFY “MDF” OR “IDF” OR A COMBINATION OF THE
11 JUNCTIONING KIT -- TWO FOR EACH FRAME. SEE NOTE 3 & 4.
12 LEFT END GUARD --
13 RIGHT END GUARD --
30 IDF VERTICAL --
40 MDF VERTICAL --

FEATURES:

• SAME BASIC VERTICAL DESIGN FOR MDF AND IDF FRAMES.
• SWIVEL TYPE MTG. BRACKET ACCEPTS END OR CENTER MOUNT TERMINAL BLOCK.
• WELDED ASSEMBLY WITH BOLT-ON FRAME COMPONENTS AND ACCESSORIES.
• UNIVERSAL TERMINAL BLOCK MOUNTING BRACKETS AND PROTECTOR BARS.
• MDF AND IDF VERTICALS CAN BE INTERMIXED IN A CONTINUOUS FRAME LINE-UP.

NOTES:

1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

2. FRAMES SUPPLIED WITH ADJUSTABLE GUARD RAILS, GROUND BAR, AND GUIDE LOOPS.
A COMPLETE SET OF ASSEMBLY PRINTS IS SHIPPED WITH EACH FRAME.

3. IDF VERTICALS (FOR MOUNTING TERMINAL BLOCKS) SUPPLIED WITH NEWTON UNIVERSAL SWIVEL
TYPE TERMINAL BLOCK MOUNTING BRACKETS.

4. MDF VERTICALS (FOR MOUNTING PROTECTORS ON VERTICAL SIDE AND TERMINAL BLOCKS ON
HORIZONTAL SIDE) SUPPLIED WITH NEWTON UNIVERSAL PROTECTOR BAR ASSEMBLY..

THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF NEWTON INSTRUMENT COMPANY NEWTON INSTRUMENT COMPANY
INC. ANY REPRODUCTION IN PART OR WHOLE WITH OUT
THE WRITTEN PERMISSION OF NEWTON INSTRUMENT
Butner, NC
COMPANY IS PROHIBITED.

E-7
005055 WALL FRAME

9/16
8 DIA.
6
ORDERING TABLE
ORDERING NO. DESCRIPTION DIM. A

00505501XX ONE VERTICAL 7-7/8"
00505502XX TWO VERTICALS 15-7/8"
00505503XX THREE VERTICALS 23-7/8"

28-5/8
30-1/8

NOTES:
DIM. A 1. XX= FINISH CODE; STANDARD FINISH FOR FRAME, XX= 30;
STANDARD FINISH FOR TERMINAL BLOCK MOUNTING
HARDWARE IS ZINC PLATED AND GOLD CHROMATE.
2. WALL FRAME COMES IN ONE (1), TWO (2) OR THREE (3)
VERTICAL UNITS.
3. SWIVEL TYPE MOUNTING BRACKET ACCEPTS EITHER
END OR CENTER MOUNTING TERMINAL BLOCKS;
THREE (3) BLOCKS CAN BE MOUNTED ON EACH
VERTICAL.

005054 WALL MOUNTING TERMINAL BLOCK BRACKET

ORDERING NUMBER: 0050540010
5-1/2

STOCK LIST
3-5/8
5 ITEM QTY. DESCRIPTION
4-1/4 1 2 WALL MTG. BRKT.
13/64 2 1 MOUNTING BAR
DIA.
3 2 10-32 X 3/4" FHMS
16-1/16 4 2 10-32 HEX NUT
15-7/16
5 2 NO. 10 LOCK WASHER

7/32 DIA.
NOTES:
1. FINISH IS ZINC PLATED AND GOLD CHROMATE.
2. MOUNTS TWO CENTER MOUNTING 8” TERMINAL BLOCKS.

E-8
004036
TERMINAL BLOCK MOUNTING BARS
004037

ORDERING TABLE
ORDERING NO. LENGTH
00403600XX 19 (5 POSITIONS)
00403700XX 23 (6 POSITIONS)

STOCK LIST
ITEM QTY. DESCRIPTION
1 2 TERMINAL BAR
2 4 12-24 X 3/4" PHMS
3 4 5/8" FLAT WASHER

1-3/8 TYP. NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

MOUNTING BARS FOR HORIZONTALLY MOUNTING TERMINAL BLOCKS
004067
TO EQUIPMENT RACKS (STATIONARY)

NOTE 2
VIEW A
ORDERING TABLE
4
ORDERING NO. DIM. A BLOCK MTG. JUMPER RING
1
SPACES (NOTE 2)
2 0040670110 18-5/16" 3 2
0040670210 22-5/16" 3 2
0040670310 27-1/16" 4 3
3 0040670410 27-1/16" 5 4
1 3/8

STOCK LIST
ITEM QTY. DESCRIPTION
1 1 TERMINAL BLOCK MOUNTING BAR
A 2 2 END CLIP
3 2 12-24 X 3/4" PHMS
4 2 1/4-20 X 5/8" RHMS

VIEW A

NOTES:
1. FOR THIS FIRST ROW OF BLOCKS, ORDER TWO (2) OF THIS
FIGURE. FOR EACH ADDITIONAL ROW, ORDER ONLY ONE (1)
MOUNTING BAR.
2. ORDER JUMPER RINGS (IF NEEDED) SEPARATELY; REFER
TO
005045.
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF NEWTON INSTRUMENT COMPANY N E W TON INSTRUMENT COMPA N Y
INC. ANY REPRODUCTION IN PART OR WHOLE WITH OUT
THE WRITTEN PERMISSION OF NEWTON INSTRUMENT
Butner, NC
COMPANY IS PROHIBITED.

E-9
004068 MOUNTING BARS FOR HORIZONTALLY MOUNTING TERMINAL BLOCKS
TO EQUIPMENT RACKS (STATIONARY)

NOTE 3 ORDERING TABLE
ORDERING NO. DIM. A
1 00406801XX 18-5/16"
00406802XX 22-5/16"
1-3/8 00406803XX 27-1/16"

7-1/2

STOCK LIST
7-1/2 ITEM QTY. DESCRIPTION
2
1 1 MOUNTING BAR
A 2 2 12-24 X 1/2" PHMS

NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.
2. BAR WILL MOUNT TWO (2) TERMINAL BLOCKS HORIZONTALLY.
3. ORDER JUMPER RING SEPARATELY (IF NEEDED); REFER TO
005045.

MOUNTING BARS FOR HORIZONTALLY MOUNTING TERMINAL BLOCKS
004069
TO EQUIPMENT RACKS (SWIVEL)
NOTE 3
ORDERING TABLE
VIEW A
BLOCK MTG. JUMPER RING STOCK LIST
ORDERING NO. DIM. A
SPACES (NOTE 3) SUPPLIED
00406901XX 18-5/16" 3 2 1
4
00406902XX 22-5/16" 3 2 2
5 00406903XX 27-1/16" 4 3 3
1

2 3 STOCK LIST
STOCK LIST
ITEM DESCRIPTION
1 2 3
1 MOUNTING BAR 1 1 1
A 2 END CLIPS 2 2 2
6
3 SWIVEL CUPS 3 3 4
4 1/4-20 X 1/2" RHMS 5 5 6
VIEW A
5 1/4 LOCK WASHER 3 3 4
6 12-24 X 3/8" PHMS 2 2 2

NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.
2. BAR WILL MOUNT TWO (2) TERMINAL BLOCKS HORIZONTALLY.
3. ORDER JUMPER RING SEPARATELY (IF NEEDED); REFER TO 005045.

SWIVELED TO
45 DEGREES

E-10
MOUNTING BARS FOR MOUNTING TERMINAL BLOCKS TO EQUIPMENT
004080
RACKS (STATIONARY)

ORDERING TABLE
VIEW A ORDERING NO. DIM. A
00408001XX 18-5/16"
00408002XX 22-5/16"

STOCK LIST
ITEM QTY. DESCRIPTION
7-1/2
1 1 SHELF ASSEMBLY
2 2 CLIP
3 2 UN. STIFF. BARS
4 4 8-32 PHMS
6 5 2 12-24 7/16" PHMS
4 6 2 1/4-20 1/2" RHMS
3
1

2 NOTES:
VIEW A
A 1. XX= FINISH CODE; SHELF STANDARD FINISH, XX= 30.
TERMINAL BLOCK, MOUNTING BRACKETS, CLIPS, ETC.
5 ARE ZINC PLATED AND GOLD CHROMATE.
2-5/16
7-5/8
8
2. FOR THE FIRST ROW OF BLOCKS, ORDER TWO (2) OF THIS
2-5/16 FIGURE. FOR EACH ADDITIONAL ROW, ORDER ONLY ONE
(1).
8
3. TERMINAL BLOCKS MAY BE SWIVELED TO ONE SIDE 45
DEGREES FOR EASIER ACCESS.
4. SHELVES MOUNT ON 8” CENTERS.

004121
ANGLE MOUNTING BRACKET
004122

ORDERING TABLE
RACK WIDTH
ORDERING NO. RACK
1 0041210010 19
0041220010 23
12-24
THREAD
7/16
STOCK LIST
ITEM QTY. DESCRIPTION
1 1 MOUNTING BAR
2 2 12-24 X 7/16" PHMS
2

1/2

NOTES:
1. ANGLE BRACKETS ARE MADE OF COLD ROLLED STEEL ANGLE.
1/2 1/8 2. BRACKETS HAVE 12-24 TAPPED MOUNTING HOLES ON 7/16”
CENTERS.

E-11
005080 TERMINAL BLOCK, 7 X 26 PIN, WIREWRAP/WIREWRAP, E/W GUARD
ORDERING TABLE

2-35/64 ORDERING ROWS NO. OF ORDERING ROWS NO. OF
THREE DIM. A DIM. A
NO. OF PINS PINS NO. OF PINS PINS
LENGTHS 1-3/8 0050800100 1 X 26 26 2-29/64" 0050800700 7 X 26 182 4-45/64"
(NOTE 5) 0050800200 2 X 26 52 2-53/64" 0050800800 8 X 26 208 5-5/64"
0050800300 3 X 26 78 3-13/64" 0050800900 9 X 26 234 5-29/64"
0050800400 4 X 26 104 3-37/64" 0050801000 10 X 26 260 5-53/64"
1-19/32 7 0050800500 5 X 26 130 3-61/64" 0050801100 11 X 26 286 6-13/64"
0050800600 6 X 26 156 4-21/64" 0050801200 12 X 26 312 6-37/64"
A
NOTES:
1. TERMINAL BLOCKS HAVE 26 PINS PER ROW.
1-19/32 4-1/2 2. LENGTH AND WIDTH OF BLOCK IS SHOWN ABOVE. HEIGHT (DIM. A) IS SPECIFIED IN
7-9 THE ORDERING TABLE.
3. END MOUNTING CENTERS USING ADJUSTABLE MOUNTING BRACKETS (WHICH ARE
INCLUDED) ARE 7”, 7-1/2”, 8”, 8-1/2” OR 9” LONGITUDINALLY AND 1-3/8” CROSSWISE.
1/2 4. MOUNTING FASTENERS ARE FURNISHED WITH EACH BLOCK.
5. PIN MATERIAL IS .040 BRASS, SPRING TEMPERED TO PROVIDE MAXIMUM STIFFNESS.
PINS ARE BRIGHT ELECTRO TIN PLATED FOR TARNISH RESISTANCE AND SOLDERABILITY.
SOLDER TO SOLDER PINS ARE AVAILABLE IN 3 LENGTHS, 1-3/8”, 1-9/16”, AND 1-3/4”. THE
LENGTHS OF SOLDER TO WIREWRAP AND WIREWRAP TO WIREWRAP ARE SHOWN IN
DIAGRAM ABOVE.
6. INSULATING STRIPS AND BASE ARE MOLDED FROM BLACK PHENOLIC MIL-P- 14F
THERMOSET PLASTIC.

005065 TERMINAL BLOCK, 8 X 26 PIN, WIREWRAP/WIREWRAP, E/W GUARD

2-5/8 ORDERING TABLE
ORDERING ROWS NO. OF ORDERING ROWS NO. OF
1-3/8 NO. OF PINS PINS
DIM. A
NO. OF PINS PINS
DIM. A
THREE
LENGTHS 0050650100 1 X 26 26 2-29/64" 0050650700 7 X 26 182 4-45/64"
(NOTE 5) 0050650200 2 X 26 52 2-53/64" 0050650800 8 X 26 208 5-5/64"
0050650300 3 X 26 78 3-13/64" 0050650900 9 X 26 234 5-29/64"
7-1/2
0050650400 4 X 26 104 3-37/64" 0050651000 10 X 26 260 5-53/64"
1-19/32 0050650500 5 X 26 130 3-61/64" 0050651100 11 X 26 286 6-13/64"
5
0050650600 6 X 26 156 4-21/64" 0050651200 12 X 26 312 6-37/64"
A
7-15/16 NOTES:
1. TERMINAL BLOCKS HAVE 26 PINS PER ROW.
2. LENGTH AND WIDTH OF BLOCK IS SHOWN ABOVE. HEIGHT (DIM. A) IS SPECIFIED IN THE
1-19/32 ORDERING TABLE.
3. END MOUNTING CENTERS ARE 7-1/2” LONGITUDINALLY AND 1-3/8” CROSSWISE OR CENTER
MOUNTS ON 5” CENTERS.
4. MOUNTING FASTENERS ARE FURNISHED WITH EACH BLOCK.
5. PIN MATERIAL IS .040 BRASS, SPRING TEMPERED TO PROVIDE MAXIMUM STIFFNESS. PINS
ARE
5/8 BRIGHT ELECTRO TIN PLATED FOR TARNISH RESISTANCE AND SOLDERABILITY. SOLDER TO
SOLDER PINS ARE AVAILABLE IN 3 LENGTHS, 1-3/8”, 1-9/16”, AND 1-3/4”. THE LENGTHS OF
SOLDER TO WIREWRAP AND WIREWRAP TO WIREWRAP ARE SHOWN IN DIAGRAM ABOVE.
6. INSULATING STRIPS AND BASE ARE MOLDED FROM BLACK PHENOLIC MIL-P-14F THERMOSET
9/16 PLASTIC.

E-12
005079 TERMINAL BLOCK, 7 X 26 PIN, WIREWRAP/WIREWRAP

ORDERING TABLE
2-35/64 ORDERING ROWS NO. OF ORDERING ROWS NO. OF
THREE DIM. A DIM. A
NO. OF PINS PINS NO. OF PINS PINS
LENGTHS 1-3/8
(NOTE 5) 0050790100 1 X 26 26 1-45/64" 0050790700 7 X 26 182 3-61/64"
0050790200 2 X 26 52 2-5/64" 0050790800 8 X 26 208 4-21/64"
0050790300 3 X 26 78 2-29/64" 0050790900 9 X 26 234 4-45/64"
0050790400 4 X 26 104 2-53/64" 0050791000 10 X 26 260 5-5/64"
1-19/32 7 0050790500 5 X 26 130 3-13/64" 0050791100 11 X 26 286 5-29/64"
A 0050790600 6 X 26 156 3-37/64" 0050791200 12 X 26 312 5-53/64"

1-19/32 4-1/2 NOTES:
1. TERMINAL BLOCKS HAVE 26 PINS PER ROW.
7-9 2. LENGTH AND WIDTH OF BLOCK IS SHOWN ABOVE. HEIGHT (DIM. A) IS SPECIFIED IN THE
ORDERING TABLE.
3. END MOUNTING CENTERS USING ADJUSTABLE MOUNTING BRACKETS (WHICH ARE IN-
1/2 CLUDED)
ARE 7”, 7-1/2”, 8”, 8-1/2” OR 9” LONGITUDINALLY AND 1-3/8” CROSSWISE.
4. MOUNTING FASTENERS ARE FURNISHED WITH EACH BLOCK.
5. PIN MATERIAL IS .040 BRASS, SPRING TEMPERED TO PROVIDE MAXIMUM STIFFNESS. PINS
ARE BRIGHT ELECTRO TIN PLATED FOR TARNISH RESISTANCE AND SOLDERABILITY. SOLDER
TO SOLDER PINS ARE AVAILABLE IN 3 LENGTHS, 1-3/8”, 1-9/16”, AND 1-3/4”. THE LENGTHS OF
SOLDER TO WIREWRAP AND WIREWRAP TO WIREWRAP ARE SHOWN IN DIAGRAM ABOVE.
6. INSULATING STRIPS AND BASE ARE MOLDED FROM BLACK PHENOLIC MIL-P-14F THERMOSET
PLASTIC.

005085 TERMINAL BLOCK, 6-1/2 X 20 PIN, WIREWRAP/WIREWRAP

THREE 2-5/8 ORDERING TABLE

LENGTHS ORDERING ROWS NO. OF ORDERING ROWS NO. OF
1-3/8 NO. OF PINS PINS
DIM. A
NO. OF PINS PINS
DIM. A
(NOTE 5)
0050850100 1 X 20 20 2-7/16" 0050850700 7 X 20 140 4-11/16"
0050850200 2 X 20 40 2-13/16" 0050850800 8 X 20 160 5-1/16"
0050850300 3 X 20 60 3-3/16" 0050850900 9 X 20 180 5-7/16"
1-19/32
6 0050850400 4 X 20 80 3-9/16" 0050851000 10 X 20 200 5-13/16"
0050850500 5 X 20 100 3-15/16" 0050851100 11 X 20 220 6-3/16"
A
0050850600 6 X 20 120 4-5/16" 0050851200 12 X 20 240 6-9/16"

1-19/32 6-7/16 NOTES:
1. TERMINAL BLOCKS HAVE 20 PINS PER ROW, DIVIDED INTO 2 BANKS OF 10.
2. LENGTH AND WIDTH OF BLOCK IS SHOWN ABOVE. HEIGHT (DIM. A) IS SPECIFIED IN THE
ORDERING TABLE.
3. END MOUNTING CENTERS ARE 6” LONGITUDINALLY AND 1-3/8” CROSSWISE.
5/8 4. MOUNTING FASTENERS ARE FURNISHED WITH EACH BLOCK.
5. PIN MATERIAL IS .040 BRASS, SPRING TEMPERED TO PROVIDE MAXIMUM STIFFNESS. PINS
ARE BRIGHT ELECTRO TIN PLATED FOR TARNISH RESISTANCE AND SOLDERABILITY.
SOLDER TO SOLDER PINS ARE AVAILABLE IN 3 LENGTHS, 1-3/8”, 1-9/16”, AND 1-3/4”. THE
LENGTHS OF SOLDER TO WIREWRAP AND WIREWRAP TO WIREWRAP ARE SHOWN IN
DIAGRAM ABOVE.
1/2 6. INSULATING STRIPS AND BASE ARE MOLDED FROM BLACK PHENOLIC MIL-P-14F
THERMOSET PLASTIC.

E-13
TERMINAL BLOCK MOUNTING BRACKET FOR CONVERTING MDF
005052
VERTICAL TO IDF

ORDERING NUMBER: 0050520000
PROTECTOR
TYPICAL MOUNTING
TERMINAL FRAME BAR
BLOCK MOUNTING STOCK LIST
1 2
ITEM QTY. DESCRIPTION
1 1 TERM. BLK. MTG. BRKT.
1/2 2 2 8-32 X 5/16 SET SCREW
NOTE 1

1-3/8

NOTES:
1. CLAMP-ON; NO DRILLING REQUIRED.

005053 CLAMP-ON TERMINAL BLOCK MOUNTING BRACKET

VERTICAL 1/2 ORDERING NUMBER: 0050530000

STOCK LIST
ITEM QTY. DESCRIPTION
1 1 MOUNTING CLIP
2 2 8-32 X 5/16" SET SCREW

1/2 NOTES:
1. THIS CLIP IS DESIGNED TO MOUNT OVER 1/4 X 1/2 BAR,
VERTICALLY OR HORIZONTALLY.
2. ORDER QUANTITY OF TWO (2) WHEN MOUNTING FIRST
1-3/8
TERMINAL BLOCK AND QUANTITY OF ONE (1) FOR EVERY
1/4 TERMINAL BLOCK THEREAFTER.

THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF NEWTON INSTRUMENT COMPANY NEWTON INSTRUMENT COMPANY
INC. ANY REPRODUCTION IN PART OR WHOLE WITH OUT
THE WRITTEN PERMISSION OF NEWTON INSTRUMENT
Butner, NC
COMPANY IS PROHIBITED.

E-14
005038 UNIVERSAL STIFFENING BAR

5 1/2
ORDERING NUMBER: 00503800XX
3

STOCK LIST
POSITIONED FOR
END MOUNTING ITEM QTY. DESCRIPTION
1 1 STIFFENING BAR
2 2 8-32 X 1/4 PHMS
1
2

U.S. PATENT NO. 3,780,351

POSITIONED FOR
CENTER MOUNTING
NOTES:
1. FINISH IS ZINC PLATED AND GOLD CHROMATE.
2. STIFFENING BAR POSITIONED FOR END MOUNTING OF TERMINAL
2
1 BLOCKS OR FOR CENTER MOUNTING OF TERMINAL BLOCKS.

005039 MAIN FRAME END CLIP, VERTICAL SIDE

ORDERING NUMBER: 00503900XX

1
STOCK LIST
ITEM QTY. DESCRIPTION
1/2" 1 1 END CLIP
2 1 5/16-18 X 5/8" HHCS
1-3/8"
3 1 5/16-18 X 9/16" HEAVY HEX NUT

2 3

NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

005040 MAIN FRAME END CLIP, HORIZONTAL SIDE

ORDERING NUMBER: 00504000XX

1 1/2 STOCK LIST
ITEM QTY. DESCRIPTION
1 1 END CLIP
2 1 5/16-18 X 5/8" HHCS
1 3/8
3 1 5/16-18 X 9/16 HEAVY HEX NUT

2 3
NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

E-15
005091
ADJUSTABLE MOUNTING BRACKET
005092
ORDERING TABLE
1-3/8 1 ORDERING NO. DIM. A
0050910010 1/2"
0050920010 9/16"

2
7" TO 9"
CENTERS STOCK LIST
ITEM QTY. DESCRIPTION
1 2 BRACKET
2 2 10-32 X 1/2 PHMS
3 4 8-32 X 1/2 RHMS
DIM. A
4 4 8-32 HEX NUT

NOTES:
1. FINISH IS ZINC PLATED & GOLD CHROMATE.
2. MATERIAL: STEEL.
3. BRACKET PERMITS 7” TO 9” ADJUSTABLE END MOUNTING WITH
MOST CENTER MOUNTING TERMINAL BLOCKS WITH 9/16” SLOT
IN BASE.

005035 UNIVERSAL PROTECTOR BAR

VIEW A
2
ORDERING TABLE
4 5
ORDERING NUMBER OF STOCK
DIM. L
NO. SHELVES LIST
SHELF 00503501XX 52" 7 1
00503502XX 60" 8 2
PROTECTOR 00503503XX 68" 9 3
00503504XX 76" 10 4
8" TYPICAL 3 1 00503505XX 84" 11 5
CENTER 00503506XX 92" 12 6
DISTANCE VIEW A 00503507XX 116" 15 7
00503508XX 124" 16 8

STOCK LIST
L STOCKLIST
ITEM DESCRIPTION
1 2 3 4 5 6 7 8
ADJUST. 1 UNIVERSAL PROTECTOR BAR 1 1 1 1 1 1 1 1
2 PROTECTOR MOUNTING LUG 8 10 12 14 14 16 20 22
3 NO. 8-32 X 5/16" RHMS 8 10 12 14 14 16 20 22
4 1/4-20 X 1/2" RHMS 7 8 9 10 11 12 15 16
5 1/4-20 HEX NUT 7 8 9 10 11 12 15 16

U.S. PAT. NO. 3,780,351

NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 15.
2. IF MORE PROTECTOR MOUNTING LUGS (ITEM NO. 2) ARE NEEDED,
ORDER BY FIG. 005051.

E-16
005051 PROTECTOR MOUNTING LUG FOR UNIVERSAL BAR

ORDERING NUMBER: 0050510010

STOCK LIST
2 ITEM QTY. DESCRIPTION
1
1 1 PROT. MTG. LUG
2 1 8-32 X 5/16 RHMS

NOTES:
1/4-20 THREAD 1. FINISH IS ZINC PLATED AND GOLD CHROMATE.

005042 SNAP-ON CABLE RING, HORIZONTAL

ORDERING NUMBER: 00504200XX

NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

005041 SNAP-ON CABLE RING, VERTICAL

ORDERING NUMBER: 00504100XX

NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

E-17
005045 OBROUND JUMPER RING

ORDERING NUMBER: 00504500XX

2
STOCK LIST
1/4 DIA. ITEM QTY. DESCRIPTION
2
1 1 JUMPER RING
2 2 1/4-20 HEX NUT
4
1

NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

005047 SELF-ALIGNING JUMPER RING
1/4" DIA.

ORDERING NUMBER: 0050470010
3-1/2"

STOCK LIST
ITEM QTY. DESCRIPTION
1 1 JUMPER RING
3 2 1 1/4-20 X 1" CARRIAGE BOLT
3 1 1/4-20 HEX NUT
1 4 1 CUP WASHER

2
4
NOTES:
1. FINISH IS ZINC PLATED AND GOLD CHROMATE.

005048
STRAIGHT JUMPER RING
005049
ORDERING TABLE
ORDERING NO. DIM. A DIM. B
00504800XX 3-1/2" 1/4"
00504900XX 3" 5/16"

STOCK LIST
2
DIM. B ITEM QTY. DESCRIPTION
(DIA.)
1 1 JUMPER RING
2 2 1/4" HEX NUT
DIM. A
1
NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.

E-18
005095 WIRE RETAINER POST FOR IDF FRAME

ORDERING NUMBER: 0050950010

2-7/8 REF.
2
1 STOCK LIST
ITEM QTY. DESCRIPTION
3 1 1 POST RETAINER
1-1/8 2 1 POST
3 2 1/4-20 X 1/2" HHCS
FRAME

NOTES:
1. FINISH IS ZINC PLATED AND GOLD CHROMATE.

005037 FLOOR SUPPORTS

ORDERING TABLE
VERTICAL ORDERING NO. DESCRIPTION
STOCK LIST
SUPPLIED
UPRIGHT
00503701XX FLOOR SUPPORT, ONE VERTICAL 1
00503702XX FLOOR SUPPORT, TWO VERTICALS 2
00503703XX FLOOR SUPPORT, THREE VERTICALS 3
00503704XX FLOOR SUPPORT, FOUR VERTICALS 4
00503705XX FLOOR SUPPORT, FIVE VERTICALS 5
00503706XX FLOOR SUPPORT, SIX VERTICALS 6
00503707XX FLOOR SUPPORT, SEVEN VERTICALS 7
00503708XX FLOOR SUPPORT, EIGHT VERTICALS 8
FLOOR
00503709XX FLOOR SUPPORT, NINE VERTICALS 9
SUPPORT 00503710XX FLOOR SUPPORT, TEN VERTICALS 10

STOCK LIST
STOCK LIST
ITEM DESCRIPTION
1 1 2 3 4 5 6 7 8 9 10
1 FLOOR SUPPORT 1 2 2 2 3 3 3 4 4 4
2 5/16-18 X 3/4" HHCS 2 4 4 4 6 6 6 8 8 8
3 5/16-18 HEX NUT 2 4 4 4 6 6 6 8 8 8

2 3
NOTES:
1. XX= FINISH CODE; STANDARD FINISH, XX= 30.
2. FOR USE WITH NEWTON DOUBLE-SIDED DISTRIBUTION FRAMES.
3. FLOOR SUPPORT IS MOUNTED TO VERTICALS THAT MOUNT
GUARD RAIL SUPPORT BARS.

E-19
005043 GROUND BAR AND SPLICE
ORDERING TABLE
NUMBER STOCK LIST
ORDERING NO.
VERTICALS SUPPLIED
0050430100 1 1
0050430200 2 2
0050430300 3 3
TYP.
8 0050430400 4 4
0050430500 5 5
0050430600 6 6
2 0050430700 7 7
4
0050430800 8 8
0050430900 9 9
0050431000 10 10

1 STOCK LIST
STOCK LIST
ITEM DESCRIPTION
1 2 3 4 5 6 7 8 9 10
3
1 GROUND SPLICE 1 1 1 1 1 1 1 1 1 1
2 1/4-20 X 3/4" HHCS 5 6 7 8 9 10 11 12 13 14
3 1/4-20 HEX NUT 5 6 7 8 9 10 11 12 13 14
4 GROUND BAR 1 1 1 1 1 1 1 1 1 1
NOTES:
1. MATERIAL: COPPER.

005044 GROUND STRAP

BOTTOM SHELF OF FRAME ORDERING NUMBER: 0050440010

NO. 6 STRANDED COPPER WIRE
STOCK LIST
PROTECTOR BAR
ITEM QTY. DESCRIPTION
2 1 1 1 1/4-20 X 1/2" RHMS
3 2 1 1/4-20 HEX NUT
FRAME UPRIGHT
3 1 GROUND WIRE ASS'Y

GROUND BAR
NOTES:
1. FINISH IS ZINC PLATED AND GOLD CHROMATE.

005093 INSULATOR BUSHING FOR MAIN FRAME FLOOR ANGLE

2
ORDERING NUMBER: 0050930000
1
ORDER AS STOCK LIST
REQUIRED
ITEM QTY. DESCRIPTION
(REFER TO
FIG. 003068) 1 1 BUSHING (NOTE 2)
2 2 3/8 FLAT WASHER

NOTES:
1. REQUIRES 3/4” DIA. HOLE TO BE DRILLED IN
FLOOR ANGLE.
2. MATERIAL IS RATED U.L. 94 V-1 AND HAS AN
OXYGEN INDEX RATING OF GREATER THAN 29.

E-20
005094 INSULATOR STANDOFF FOR GROUND BAR

COPPER GROUND BAR

2
ORDERING NUMBER: 0050940000

STOCK LIST
ITEM QTY. DESCRIPTION
1 1 STANDOFF (NOTE 1)
2 2 1/4-20 X 1/2" HHCS

NOTES:
1. MATERIAL IS RATED U.L. 94 V-1 AND HAS AN OXYGEN INDEX
RATING OF GREATER THAN 29.

INSULATOR
GROUND
BAR

E-21
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF NEWTON INSTRUMENT COMPANY N E W TON INSTRUMENT COMPA N Y
INC. ANY REPRODUCTION IN PART OR WHOLE WITH OUT
THE WRITTEN PERMISSION OF NEWTON INSTRUMENT
Butner, NC
COMPANY IS PROHIBITED.

E-22