TM
The Milano Collection
Tuscany Cot Siena Cot
Assembly Instructions for your Tasman Eco Furniture 4 in 1 Cot
Bassinet Cot Junior Bed Chaise Lounge
The following instructions show the assembly of our Siena Cot from our Milano collection. As all cots are designed off the same base, these
instructions are applicable across the whole Tasman Eco Furniture Cot range. Assembly of this furniture is best undertaken by two people.
Right Bed Head
Base
T
H
IS
S
ID
E
U
P
T
H
IS
S
ID
E
U
P
Tuscany Connector Bolts
100mm x 8
Front Adjustable Panel
With Glide Pins
Sienna Connector Bolts
65mm x 8
Guard Screws x2
Cross Dowels
Left Bed Head x 4 (Cot/Bassinet)
Rear Fixed Panel x 4 (Junior Bed)
Double Ended Screws x 4
Junior Bed Rails x 2
Not required when
building Cot or Bassinet
Allen Key x 1
Due to the heavy nature of the cot, it is recommended assembly is undertaken by two people.
Assembly is easiest when carried out as shown. Assembly requires a Flat Head or Phillips Head screwdriver; and an Allen key (supplied).
2
1 Prepare Base
Top face down for this
stage of assembly
a) Begin by laying the base frame down on the floor. NOTE: The top of the base is
marked “This Side Up” and must be facing downwards for this stage of assembly.
b) Insert the metal cross dowels into the four holes in the base. The screw heads must
face upwards. Align the hoizontal holes using a screwdriver as shown.
2 Connect Bed Heads To Base When building the Cot, use locating holes set ‘A’
When building the Bassinet, use locating holes set ‘B’
a) Connect the base to the left bed head. Ensure the metal guide channels on both bed head frames are facing the
correct way for this stage of assembly. Screw the two sections together using 2 bolts, but do not fully tighten.
b) Now connect the right bed head to the base. Screw the sections together using 2 bolts, but do not fully tighten.
B A
B A
THIS SIDE UP
THIS SIDE UP
Guide channels
B A
must face
downwards for this
stage of assembly
A
B
3 Fit Double Ended Screws To Unused Holes
Use the Double Ended Screws to fill the four unused locating
holes (set ‘A’ or set ‘B’ as shown above). This is required to prevent
the entry of small fingers into these holes.
A
B
3
4 Connect The Rear (Fixed) Panel
Connect the rear (fixed) panel to the bed heads using 2 bolts on
either side. IMPORTANT: Ensure the flush face of the panel faces
the inside of the cot. Screw the sections together but do not fully
tighten at this time.
THIS SIDE UP
THIS SIDE UP
Flush side must
face inwards
With these sections now assembled, carefully lift up and stand the cot on its legs.
5 Connect The Front (Adjustable) Panel
Insert the front (adjustable) panel between the left and right bed heads. NOTE: It is best to have assitance at this stage to avoid
damaging the side frames when inserting the glide pins into the guide channels. The bed head frames will need to be spread apart slightly
so the glide pins do not damage the timber. If required, untighten the bolts holding the frames together.
Push the upper glide pins into the top of the guide channels on the bed head frames. Depress the front locking buttons to release the
locks and then slide the front panel down a touch on either side. Once the top glide pins are in place, slide the bottom glide pins into the
bottom guide channels.
UP
SIDE
THIS
Flush side must
P
U
E
D
SI
IS
TH
face inwards
Front (Adjustable) Panel
4
The guard screws must be installed to
6 Fit The Guard Screws prevent damage to the timber frames
IMPORTANT: The top of the guide channels (both sides) must now be
secured using the 2 guard screws. The guard screws prevent damage
being caused to the side frames by preventing the front adjustable
panel from being accidentally removed or dislodged from the bed head
frames. This is also an important safety feature.
Fit to both sides
7 Tighten All Bolts
Tighten all connecting bolts. Do not overtighten or you may damage the timber.
T
H
Tighten both sides
IS
SI
D
E
U
P
TH
IS
SI
D
E
U
P
Assembly is now complete
Lowering And Raising The Adjustable Panel
To lower the side, you must first lift it slightly then press the buttons
inwards simultaneously. Ensure that your hands are in a position to
support the side and slowly lower it.
To raise the side, simply lift it up with both hands until you hear it
click. The springs will automatically lock back into place.
Maintaining Your Tasman Eco Cot
To clean, wipe down with a soft cloth and soapy water. Avoid scourers and steel wool as
these will damage the finish. Two months after assembling the cot, re-tighten all connec-
tor bolts as some may loosen as the cot settles.
5
Converting The Cot Into A Junior Bed
1 To convert your Tasman Eco Cot into a Junior Bed, begin by
loosening all bolts around the cot, removing the guard screws
and removing the front panel from the cot as shown in steps
1, 2 and 3 on the page opposite.
2 Remove the bolts holding the rear (fixed) panel and
then remove the panel.
3 To protect your child from rolling out of the bed, we have
supplied 2 junior bed rails. To assemble these rails, use the
cross dowels supplied by pushing them into the base of the
rails and aligning the screw hole.
4 Retighten all bolts, but. do not overtighten.
Tighten
both sides
6
Converting The Cot Into A Chaise Lounge
1 To convert your Tasman Eco Cot into a Chaise lounge,
begin by loosening all bolts around the cot.
Loosen
both sides
2 Remove the guard screws.
3 Remove the adjustable front panel from the bed head frames.
4 Retighten the bolts. (Do not overtighten).
Tighten Place a throw rug over the mattress, add a few colourful pillows and
your child has their very own Chaise lounge where they can read,
both sides rest or play.
TM
7
If the purchaser of this item is not completely satisfied with this item over the period of its life in the purchaser’s possession, Tasmaneco Eco
Furniture Pty Ltd, will replace this item free of charge, subject to the conditions below. The product must be returned to Tasman Eco Furniture
Pty Ltd with proof of purchase, date and amount of purchase. This guarantee is not transferable.
Conditions.
The ‘Lifetime Guarantee’ will be nullified in circumstances where:
1. The item is transferred, gifted or disposed of by the purchaser to another.
2. The item is improperly assembled or adjusted and or not assembled strictly in accordance with the written instructions provided
by the seller in the box containing the item.
3. The item is disassembled and then reassembled.
4. Damage is deemed by the Tasman Eco Furniture Pty Ltd to be caused or induced to the item by the buyer.
5. The item or parts of it are modified which were not authorised in writing by Tasman Eco Furniture Pty Ltd.
6. The item is misused by the buyer or anyone for whom the buyer has legal responsibility (including a minor).
7. The item is used and or operated outside of the physical or environmental specifications of the product.
Registration and Claims.
To be eligible for the above Lifetime Guarantee, you must register your details online at www.tasmaneco.com.au immediately upon purchasing
the cot. For all claims, please email us at claims@tasmaneco.com.au or visit the store where the cot was purchased.
WARNING:
Safety Consideration for your Child.
Follow the manufacturers assembly instructions in detail to ensure the safety features of the cot are not compromised.
• ENSURE THE COT IS NOT PLACED TOO CLOSE TO HEATERS, BLINDS, CURTAINS, WINDOWS OR POWER POINTS.
• DO NOT HANG ANYTHING NEARBY WHERE THERE IS A POTENTIAL DANGER OF THE ITEM FALLING INTO THE COT.
• KEEP ANY MEDICATION, STRING, ELASTIC, SMALL TOYS OR SMALL ITEMS SUCH AS MONEY OUT OF REACH FROM ANY
POSITION IN THE COT. It is advisable to keep all items out of your childs cot to prevent suffocation or strangulation.
• THE BASE OF THE COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE YOUR CHILD CAN SIT UP.
• WHEN CONVERTING THE COT TO A JUNIOR BED, THE SIDE RAILS SHOULD BE INSTALLED TO PREVENT FALLS.
Recommended Mattress Size.
This cot has been manufactured for use with a mattress which measures 750mm (wide) x 1310mm (long) x 120mm (maximum thickness). The
width and length are specified because it is IMPORTANT that the gaps between the mattress and the sides and ends of the cot do not exceed
40mm. This is to minimise the risk of a child’s limb becoming caught in the gap. The thickness of the mattress has been specified to ensure
that the depth of the cot is greater than 500mm with the mattress base in the lower position to minimise the risk of a child climbing or falling
out of the cot.
Safety Consideration for Cot.
TO ENSURE SAFETY, REGULARLY CHECK ALL OF THE CONNECTING BOLTS AND GLIDE PINS MAKING SURE THAT THEY ARE TIGHT.
This product has been independently tested and complies
with Australian Standards AS/NZS 2172:2003
(Cots for household use - Safety requirements)
TM
Tasman Eco Furniture Pty Ltd abn. 58 106 988 578
9 Lincoln St, MINTO, NSW 2566 p.o. box 5878 MINTO DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000 e. info@tasmaneco.com.au w. www.tasmaneco.com.au
8 cot-mil-0208