Chapter 3
CMOS processing technology (II)
● Twin-tub CMOS process
1. Provide separate optimization of the n-type and p-type transistors
2. Make it possible to optimize "Vt", "Body effect", and the "Gain" of n, p
devices, independently.
3. Steps:
A. Starting material: an n+ or p+ substrate with lightly doped ->
"epitaxial" or "epi" layer -> to protect "latch up"
B. Epitaxy"
a. Grow high-purity silicon layers of controlled thickness
b. With accurately determined dopant concentrations
c. Electrical properties are determined by the dopant and its
concentration in Si
C. Process sequence
a. Tub formation
b. Thin-Oxide construction
c. Source & drain implantations
d. Contact cut definition
e. Metallization
● Balanced performance of n and p devices can be constructed.
(Substrate contacts are included in Fig.3.10)
2003/3/12 CMOS Process (II) 1
(7~8um)
青玉 or SiO2 (二氧化矽)
Anisotropic Etch
Form p-island
(for n-device)
Form n-island
(for p-device)
2003/3/12 CMOS Process (II) 2
- Grow gate oxide through
thermal oxidation
- Deposit Doped Polysilicon
Etch Polysilicon
Step (h): n-implantation for
source & drain
Step (i) p-implantation
Step (j)
- Grow phosphorus glass
- Etch glass to form contact cut
- Evaporating alumni
2003/3/12 CMOS Process (II) 3
3.3 CMOS Process Enhancement (Interconnection)
3.3.1 Metal Interconnect
* CMOS circuit = CMOS logic process +
Signal/Power/Clock-routing layers
- Second-layer of metal (VIA1=M1 to M2)
- Note: M1 must be involved in any contact to underlying areas
Etch
Isolation
layer
Contact Form a
VIA
(polysilicon, diffusion)
- Process steps for two-metal process (Omitted)
3.3.1.2 Poly Interconnect
- Polysilicon layer is commonly used as interconnection of
signals.
- Reduce resistance of polysilicon → to make long-distance
interconnection
- Combine polysilicon with a refractory metal (Silicon + Tantalum)
2003/3/12 CMOS Process (II) 4
Ω=20-40Ω/square Ω=1-5Ω/square Make long-distance
(for interconnect)
3.3.1.3 Local Interconnection
- Local Interconnection allow a “direct” connection between
ploysilicon and diffusion , alleviating the need for area-intensive
contacts and metal
- Example: Use of Local Interconnect in SRAM (save 25%)
2003/3/12 CMOS Process (II) 5
3.4 Layout Design Rules
- Function: obtain a circuit with optimum yield in an area as well as
possible
- Performance ←→ yield
* Conservative design rules → Functional circuit
→ Good yield
* Aggressive design rules → Bad yield
→ Compact circuit/layout for
low cost and high speed
(A) Line width/spacing
Small → open circuit
Close → short circuit
(B) Spacing between two independent layers
- In process:
(a) Geometric features for mask-making and lithographical
(b) Interactions between different layers (e.g., poly + diffussion)
- Rules:
a. Micro(μ)-based rules – Industry (submicron)
b. Lambda-based rules: e.g.,, 1λ=0.6um for 1.2 um
CMOS process) for 4-1.2um Scalable CMOS
process. 2λ is the minimum channel length (L).
- See Table 3.2 and figures (next four pages)
2003/3/12 CMOS Process (II) 6
2003/3/12 CMOS Process (II) 7
2003/3/12 CMOS Process (II) 8
Layout Design Rules:
2003/3/12 CMOS Process (II) 9
Contact Rules: There are several generally available contacts:
- Metal to p-active (p-diffusion)
- Metal to n-active (n-diffusion)
- Metal to Polysilicon
- VDD and VSS substrate contacts
- Split (Substrate contacts)
3.4.5 Layer assignment (Table3.4)
- CIF: Caltech Intermediate Form
- GDSII Format
2003/3/12 CMOS Process (II) 10
2003/3/12 CMOS Process (II) 11
3.5 Latchup
- Latchup : Shorting of VDD and Vss lines → Chip breakdown
- Latchup Equivalent Circuit:
Vertical : pnp
- p = source/drain of p device (Emitter)
- n = n-well (Base)
- p = p-substrate (Collector)
Lateral : npn
- n = source/drain of n device (Emitter)
- p= p-substrate (Base)
- n= n-well (Collector)
Rsubstrate, Rwell
- Parasitic devices and resistors
2003/3/12 CMOS Process (II) 12
Latchup triggering: Transient/Impulse current in start-up
A. Lateral triggering: current flows in the emitter of the lateral
npn-transistor
Vpnp-on
→Trigger point : In,trigger =
αnpn ˙Rwell
- Vpnp,on = 0.7V
- αnpn = common base gain of the lateral npn device
- Rwell = well resistance
B. Vertical triggering: Sufficient current is injected into the
emitter of the vertical pnp transistor
3 .5.3 Latchup prevention
- Latchup occur
(βnpn+1)(IR,sub+IR,wellβpnp)
βnpn˙βpnp > 1 +
(IDD-IR,sub)
VBE,,npn
Where IR,sub =
Rsub
VBE,,npn
IR,well =
Rsub
IDD = total supply current
2003/3/12 CMOS Process (II) 13
Observation to prevent latchup:
1. Reduce the resistor values
2. Reduce the gain of the parasitic devices
- Approach:
1.Latchup-resistant CMOS process
2.Layout techniques (see section 3.5.4,3.5.5)
3.6 Technology-related CAD tools
- Design Rule Check (DRC): On-line DRC and Off-line (Dracula)
(3.6.1)
- Circuit extraction (Layout Parameter Extraction, LPE) (3.6.2)
- CMOS process simulator (Process Input Description Language
(PIDL))(sec.3.9) and Supreme by Stanford University.
2003/3/12 CMOS Process (II) 14