CODICI DI ERRORE RICOH
RICOH AFICIO 200
CODICE DESCRIZIONE
SC120 Scanner home position
SC121 Scanner home position
SC122 Scanner home position
SC123 Scanner home position
SC192 Automatic SBU Adjustment error. POSS: Iamp, Dirty White Plate, Lamp
Regulator, SBU
SC302 Charge Roller Current Leak
SC306 Charge Roller Home Position
SC320 Polygon motor
SC321 No Laser Start Signal
SC322 Laser Sync Error
SC324 LD drive current over
SC390 TD Sensor Error 1
SC391 Developer Bias Leak
SC393 TD Sensor Error 2
SC401 Transfer Roller Leak
SC402 Transfer Roller Leak
SC411 Separation Bias Error
SC500 Main Motor
SC503 Upper Paper Tray Lift Motor –OPTIONAL PAPER TRAY UNIT
SC504 Lower Paper Tray LIft Motor –OPTIONAL PAPER TRAY UNIT
SC506 Main motor –OPTIONAL PAPER TRAY UNIT
SC542 Fuser warm up error
SC543 Fuser over temp
SC546 Fuser temp. not steady falls or increases 10 durring standby
SC547 Zero cross signal POSS: power suppty, IOCSS, BICU
SC610 Communication error between duplex and IOCSS
SC691 Communication error between BICU and Fax
SC692 Communication error between Printer and BICU
SC900 Counter error – check fuse #5
SC92O Communication error between BICU and MSU
SC921 MSU Hardware error POSS: front door safety switch
SC980 Program Loading Error POSS BICU, ROM
SC981 NVRAM Clear error
SC990 Communication error between IOCSS and BICU
Enter service mode (SP) --HoId the (C/S) Button for 4 seconds then enter 1 --- O ----7 --- (C/S),
Exit service mode: by pressing (C/S) three times.
Reset fuser and some other error codes by Enter SP 5-810 and select 1 press and hold photomode key while
holding photomode key press (#) key
Failing polygon (SC320) motor usually caused by overheating because of defective cooling fan.SC503/504 tray
Lift motor malfunction (SC503,5O4) First check for paper behind the trays otherwise open the combined lift
motor of the paper tray unit and you will see one of the wires from the liftmotor is broken from the contact.
RICOH AFICIO 250
CODICE DESCRIZIONE
SC101 Scan Lamp Error
SC120 Scanner home position
SC121 Scanner home position
SC122 Scanner home position
SC123 Scanner home position
SC192 Automatic SBU Adjustment error. POSS: Iamp, Dirty White Plate, Lamp
Regulator, SBU
SC302 Charge Roller Current Leak
SC306 Charge Roller Home Position
SC320 Polygon motor
SC321 No Laser Start Signal
SC322 Laser Sync Error
SC324 LD drive current over
SC390 TD Sensor Error 1
SC391 Developer Bias Leak
SC393 TD Sensor Error 2
SC4O1 Transfer Roller Leak
SC402 Transfer Roller Leak
SC411 Separation Bias Error
SC500 Main Motor
SC503 Upper Paper Tray Lift Motor -- optional paper tray unit
SC504 Lower Paper Tray LIft Motor -- optional paper tray unit
SC506 Main motor -optional paper tray unit
SC542 Fuser warm up error
SC543 Fuser over temp
SC546 Fuser temp. not steady falls or increases 10 durring standby
SC547 Zero cross signal POSS: power supply, IOCSS, BICU
SC548 Fuser Edge Temp High POSS: Thermistor or PSU
SC549 Fuser Edge Temp Low POSS: Thermistor or PSU
SC610 Communication error between duplex and IOCSS
SC681 Wrong Fax Option
SC682 Wrong Print Option
SC691 Communication error between BICU and Fax
SC692 Communication error between Printer and BICU
SC900 Counter error
SC920 Communication error between BICU and MSU
SC921 MSU Hardware error POSS: front door safety switch
SC980 Program Loading Error POSS BICU, ROM
SC981 NVRAM Clear error
SC990 Communication error between IOCSS and BICU
Enter service mode (SP) --HoId the (C/S) Button for 4 seconds then enter 1 --- O ----7 --- (C/S),
Exit service mode: by pressing (C/S) three times.
Reset fuser and some other error codes by Enter SP 5-810 and select 1 press and hold photomode key while
holding photomode key press (#) key
RICOH AFICIO 1035/1045
CODICE DESCRIZIONE
SC101 Exposure Lamp Error
SC120 Scanner home position error I
SC121 Scanner home position error 2
SC130 SBU defective
SC131 F-Gate asserts during shading
SC302 Charge roller current leak
SC304 Charge roller current correction error
SC320 Polygon motor error
SC321 No Laser Start Signal, F-Gate error
SC322 first laser synchronization error
SC323 LD drive current over
SC326 2nd laser synchronization error
SC327 LD unit home position error 1
SC328 LD unit home position error 2
SC329 LD unit beam pitch misadjusted
SC350 ID sensor pattern test error
SC351 ID sensor VSG test error
SC352 ID sensor, pattern edge detect error
SC353 ID sensor, LED current abnormal at initialization
SC354 ID sensor timeout abnormal adjustment
SC390 TD Sensor Error
SC391 TD Sensor Auto Adjust Error
SC395 Development output abnormal, developer bias leak
SC401 Transfer Roller Leak
SC402 Transfer Roller Open
SC403 Transfer belt error: position, drive
SC405 Transfer belt error: drive, sensor
SC440 Main Motor
SC490 Exhaust fan
SC492 Cooling fan
SC501 1st Paper Tray Lift
SC502 2nd Tray Iift malfunction
SC503 3rd Tray Iift malfunction – OPTIONAL PAPER TRAY UNIT
SC504 Lower Paper Tray Lift – OPTIONAL PAPER TRAY UNIT
SC506 Main motor – OPTIONAL PAPER TRAY UNIT
SC507 LCT Main motor lock
SC510 LCT Lift malfunction
SC541 Thermistor open
SC542 Fuser warm up error
SC543 Fuser over temp
SC544 Fuser over temp
SC545 Fusing Iamp remains on: Thermistor out of position
SC546 Fusing temperature unstable
SC547 Zero cross signal POSS: power supply
SC548 No Fuser lnstalled
SC599 Optional Output bin motor lock
SC601 Communication error between BICU and Scanner Unit
SC610 Communication timeout error between ADF and BICU
SC611 Communication break error between BICU and ADF
SC612 Communication command error between BICU and ADF
SC620 Communication timeout error between BICU and Finisher
SC621 Communication timeout error between BICU and Finisher
SC623 Communication timeout error between BICU and paper tray unit
SC624 Communication break error between BICU and Paper Tray Unit
SC626 Communication timeout error between BICU and LCT
SC627 Communication break error between BICU and LCT
SC630 Communication failure with CSS
SC640 BICU control data transfer sum-check
SC641 BICU control data transfer abnormal
SC670 Engine Response error
SC672 Operation panel communication error
SC690 BICU
SC691 BICU
SC692 BICU
SC700 ADF Pickup error
SC701 ADF Pickup Lift error
SC722 Finisher jogger motor error
SC724 staple motor error
SC725 Finisher stack feed-out motor error
SC726 Finisher shift tray 1 Iift motor error
SC727 Finisher stapler rotation motor error
SC729 Finisher punch motor error
SC730 Finisher stapler positioning motor error
SC731 Finisher exit guide motor
SC732 Finisher upper tray shift motor error
SC733 Finisher lower tray Iift motor error
SC744 Finisher lower tray shift motor error
SC800 Control Board Defective
SC804 Control Board Defective
SC819 Software Error
SC820 SeIf-Diagnostic Error: CPU
SC821 SeIf-Diagnostic Error: ASIC
SC822 SeIf-Diagnostic Error: HDD
SC823 SeIf-diagnostic Error: NIB
SC824 SeIf-diagnostic Error: NVRAM
SC826 SeIf-diagnostic Error: Optional NVRAM
SC827 SeIf-diagnostic Error: RAM
SC828 SeIf-diagnostic Error: ROM
SC829 SeIf-diagnostic Error: Optional RAM
SC835 SeIf-Diagnostic Error: Parallel Interface
SC836 SeIf-diagnostic Error: Resident Font
SC837 SeIf-diagnostic Error: Optional Font
SC838 SeIf-diagnostic Error: Clock Generator
SC850 Network l/F
CS51 IEEE 1394 l/F Abnormal
SC860 Hard Disk Error
SC865 Hard Disk Error
SC900 Counter error Electronic
SC901 Counter Mechanical
SC951 F-gate error at write request
SC953 Software defective
SC954 Software defective
SC955 Software defective
SC964 Software defective
SC984 Print image data transfer error: Controller Board
SC985 Scanner image data transfer error: Controller Board
SC986 Software defective
SC990 Software defective
SC991 Software defective
SC996 FCU board error
SC997 Software defective
SC998 Software defective
SC999 Program download error
Enter service mode(SP): Press the clear mode key. enter 1-0-7 hold down the c/s for three seconds.
To enter the special service mode hold the # key down while pressing Copy SP.
Exit service mode: by pressing exit twice
Reset fuser and some other error codes by Entering the sp mode and cycling the power.
RICOH AP3800/828 – GESTETNER DSc38 -
SAVIN SLP38c
CODICE DESCRIZIONE
SC195 Serial Number Mismatch
SC201 Polygon motor
SC220 Synch. detection signal error 1 (001: Y), (002: M), (003: C), (004: K)
SC221 Synch. detection signal error 2 (001: Y), (002: M), (003: C), (004: K)
SC230 FGATE error: (001: Y), (002: M), (003: C), (004: K)
SC231 FGATE Timeout: (001: Y), (002: M), (003: C), (004: K)
SC240 LD over (001: Y), (002: M), (003: C), (004: K)
SC260 LD HP sensor not switched on (for K only)
SC261 LD HP sensor not switched on (for K only)
SC285 Line position adjustment (MUSIC) error
SC370 TD sensor (K): Adjustment Error
SC371 TD sensor (Y): Adjustment Error
SC372 TD sensor (C): Adjustment Error
SC373 TD sensor (M): Adjustment Error
SC374 Vt error (K)
SC375 Vt error (Y)
SC376 Vt error (C)
SC377 Vt error (M)
SC380 K dev. motor error
SC381 Color dev. motor error
SC385 ID sensor VSG adjustment
SC386 Development gamma error (K)
SC387 Development gamma error (Y)
SC388 Development gamma error (C)
SC389 Development gamma error (M)
SC390 Development Bias output
SC391-01 Charge AC: output error
SC460-001 Thermistor 1(open circuit)
SC460-002 Thermistor 1(short circuit)
SC461-001 Thermistor 2 (open circuit)
SC461-002 Thermistor 2 (short circuit)
SC471 transfer belt H.P.
SC490 Transfer bias paper attraction roller bias leak
SC501 Paper Tray 1
SC502 Paper Tray 2
SC503-01 Tray 3 error (Paper Feed Unit or LCT)
SC501-02 Tray 3 error (Paper Feed Unit or LCT)
SC504-01 Tray 4 error
SC504-02 Tray 4 error
SC530 Fusing fan
SC541 Heating roller thermistor
SC542 Heating roller warm-up error
SC543 Heat roller Iamp overheat
SC544 Heating roller fusing Iamp 10w temp
SC545 Heat roller Iamp Short
SC546 Heat roller fusing Iamp temperature fluctuation
SC551 Pressure roller thermistor
SC552 Pressure roller warm-up
SC553 Pressure roller fusing Iamp over temp
SC554 Pressure roller fusing Iamp Iow temp
SC555 Pressure roller fusing Iamp short
SC556 Pressure roller fusing Iamp temp fluctuation
SC560 Zero cross
SC621 Finisher/mailbox communication
SC622 Bank communication
SC623 Duplex unit communication
SC640 BCU - Controller communication
SC641 BCU —Controller communication
SC670 No response from BCU at power on
SC680 BCU/ MUSIC communication
SC687 Memory address command
SC722 Finisher jogger motor
SC724 Finisher staple hammer motor
SC725 Finisher stack feed-out motor
SC726 Finisher shift tray 1 Iift motor
SC727 Finisher stapler rotation motor
SC729 Finisher punch motor
SC730 Finisher stapler motor
SC731 Finisher exit guide plate motor
SC732 Finisher tray 1 shift motor
SC733 Finisher tray 2 Iift motor
SC734 Finisher tray 2 shift motor
SC818 Software
SC835 Centronics interface
SC836 Font ROM
SC837 Font ROM
SC850 Network interface
SC851 EEE 1394
SC860 HDD
SC861 HDD
SC863 HDD
SC864 HDD
SC865 HDD
SC900 Electroctronic counter error
SC990 Defective software
SC998 Application start error
RICOH AFICIO 180/150
CODICE DESCRIZIONE
SC122 Scanner home position
SC320 Polygon motor
SC322 Laser Sync Error
SC402 High Voltage Leak Transfer or Charge
SC542 Fuser warm up error
SC543 Fuser over temp
SC544 Fuser Iow temp
SC546 Fuser temp. not steady
SC547 Zero cross signal POSS: power supply, Fuser ground strap touching Iamp
SC620 Communication error between BICU & ADF.
SC691 Communication error between BICU and Fax
SC901 Counter error --check fuse #4
Fuser reset procedure: SP5-810 select 1, press and hold the photo mode key and then press and hold
the enter key and wait for 5 beeps.
0-00 DIS or NSF not detected - Check connections to fax pcb and BICU
0-01 DCN received unexpectedly - Remote fax stopped TX
0-03 incompatible modem at other end - Check remote fax
0-21 EOL signal from other end not received: change G3 switch 0A bit 4 to a 1
A4 fax print on two pages: set printer switch 03, bit 0 to 1 and printer switch 04 to 00111111
Counter inizialize: SP mode 7-825
Disable speaker - set G3 switch “00” bit 0 and 1 to 0
Envelope ard bypass printing - set paper in user tools/printer/job control/paper input /bypass/standard
DF jams, no paper present: Can be caused by excessive light
Fax option not recognized - Turn on SW3 turn off SW1
APS through ADF, reads wrong size - Clean Sliding electrodes on bottom of DF
Maintenance Call Reset - SP7-909
Printer alarm light: reset PM counter SP7-909 / Reset PM display SP5-908
RICOH AFICIO 1027/1022
CODICE DESCRIZIONE
SC101 Exposure Iamp
SC120 Scanner home (no detect)
SC121 Scanner home (doesn’t leave)
SC122 Scanner detects early home
SC123 Scanner doesn’t return home
SC144 Communication between SBU and IPU PCB
SC191 IPU board incorrect for machIne
SC192 SBU adjustment error
SC193 Error Image transfer (IPU Defective)
SC195 DFGATE (ADF Communication)
SC196 DFGATE (ADF Communication)
SC197 DFGATE (ADF Communication)
SC198 Memory address (firmware, SBCU, IPU)
SC199 DF scanning (ADF, SBCU, Firmware)
SC302 Charge Leak
SC320 Polygon motor
SC322 Laser synchronization
SC323 LD drive current over
SC355 ID sensor
SC389 TD sensor
SC390 TD sensor
SC391 Development bias leak
SC392 TD sensor initial setting failure
SC401 Transfer Leak
SC402 Transfer Leak
SC411 Separation leak
SC490 Toner supply motor
SC500 Main motor
SC501 1st paper tray lift
SC502 2nd paper tray Iift
SC503 3rd paper tray Iift
SC504 4th paper tray Iift
SC506 Paper tray motor lock
SC508 Rear fence drive (LCT)
SC509 Side fence drive (LCT)
SC510 LCT Iower limit
SC520 Paper tray
SC541 Thermistor open (fuser)
SC542 Warm-up error (fuser)
SC543 Overheat (fuser)
SC544 Overheat (fuser)
SC545 Lamp remains on (fuser)
SC546 Unstable temperature (fuser)
SC547 Zero cross
SC548 Copier does not detect fuser
SC590 Exhaust fan
SC611 Communication error between SBCU and ADF
SC612 Communication error between SBCU and ADF
SC620 Communication error between SBCU and finisher
SC621 Communication error between SBCU and finisher
SC630 Communication failure with CSS
SC640 SBCU Error (control PCB or SBCU)
SC641 SBCU Error (control PCB or SBCU)
SC650 Communication error between SBCU and duplex
SC670 Engine response
SC672 Communication error controller and op panel
SC720 Finisher ogger motor
SC722 Finisher jogger motor
SC724 Finisher stapler motor
SC725 Finisher stack feed motor
SC726 Finisher Iift motor
SC727 Finisher stapler motor
SC728 Finisher stack
SC730 Finisher stapler motor (movement)
SC731 Output tray motor
SC732 Finisher shift motor
SC770 Shift tray motor
SC791 Communication error between SBCU and Bridge
SC792 Finisher connection
SC793 Interchange communication
SC800 Controller board
SC804 Controller board
SC818 Watchdog error (Controller board)
SC819 Firmware
SC820 CPU error or Firmware
SC821 Controller board
SC822 HardDrive
SC823 Network Card
SC824 NVRAM
SC826 NVRAM
SC827 Firmware
SC828 Controller board or firmware
SC829 Optional memory
SC835 Parallel Interface
SC836-838 FONT Controller board
SC850 Network Card
SC851 IEEE 1394 I/F
SC860-864 Hard drive
SC865 Hard drive or controller
SC900 Electronic total counter over 10 mil-yeah right replace nvram on controller
SC901 Mechanical counter
SC951 Firmware or SBCU
SC953 Firmware
SC954 Printer setting error (Firmware, IPU, or Controller)
SC955 Memory setting error (Firmware, IPU, or Controller)
SC964 Printer Ready error (Firmware, IPU, or Controller)
SC984 data transfer error (Controller or SBCU)
SC986 Firmware
SC900 Firmware
SC991 Software error Iogged
SC996 FCU
SC997 Firmware
SC998 Firmware
SC999 Firmware download error
Enter service mode (SP): Press the clear mode key. enter 1-0-7 hold down the c/s for three seconds.
Reset Fuser: Enter SP mode and cycle power
SP5-801 Memory All Clear