PRECAUTION
Do not place object containing liquids (flower
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS vase, etc.) on top of the monitor.
APPLIANCE TO RAIN OR OTHER MOISTURE. If water or any other liquid does get inside the monitor,
To avoid electrical shock, do not open the cabinet. immediately turn it off and unplug it.
Refer servicing to qualified personnel only. Do not get the monitor wet
If the power supply cord (AC power cord) of this
appliance is damaged, it must be replaced. Return to a • Do not allow the monitor to get wet or allow water or other
liquids inside it. Doing so may cause a fire or electric shock.
SANYO Authorised Service Centre for replacement of Be especially careful during rainy weather, snowy weather,
the cord. near the beach, or near bodies of water.
• Do not use the monitor in a bathroom.
If an abnormality does occur, turn the power switch off and
unplug the unit. Have a qualified technician perform any
Do not use the monitor during a lightning
repairs. Do not touch it or its power cord during a lightning. Doing so
Do not use the monitor if it makes a strange noise, emits a may cause an electric shock.
strange odor, or if smoke comes out from it
Do not place the monitor on an unstable surface
If used under these conditions, the monitor may cause a fire or
It may fall, causing damage or personal injury. If it falls and its
electric shock. Immediately unplug it and wait to make sure no
body is damage, immediately turn it off and unplug.
more smoke comes from it. Then take it to the dealer for service.
Do not try to repair or open the monitor yourself. Never pull on the cord to unplug the power cord
Do not allow the power cord to get damaged • Always unplug the power cord by holding the power plug and
slowly pulling out.
• Do not place heavy objects on the power cord.
Pulling at the cord may damage the power cord and cause a
• Do not place the power cord near a heat source. fire or electric shock.
• Do not excessively bend the power cord, modify it, or secure
• Do not touch the power cord or plug with wet hands. Doing so
it with staples. may cause an electric shock.
Doing so may damage the power cord and cause a fire or
electric shock. Cautions regarding the location where the
If the power cord is damaged, take it to the dealer and have it monitor is used.
replaced. • Do not place it in locations with excessive humidity or dust, or
location subjected to oily vapors or steam.
• Do not place it in locations subject to direct sunlight or near
heat generating equipment. Doing so may cause an accident
Do not allow dust or dirt to build up on the
property damage.
power cord or power outlet
A build-up of dust may cause a short circuit or generate heat Do not cover the air vents
and cause a fire. Do not place the monitor in a poorly ventilated location. Do not
Be especially careful when using the monitor in areas of high block its air vents by covering it with a cloth, placing it on a
humidity, in areas with frequent condensation, in kitchens, and in carpet or blanket, or other means. If the air vents are blocked,
places where there is excessive dust. the internal temperature will rise and it may cause a fire.
Periodically unplug the power cord and clean away the dust that
builds up between the plug terminals.
Cleaning
• Dirt can be removed from the cabinet by wiping it with a soft
Cautions when plugging in the power cord cloth. To remove stains, wipe with a soft cloth moistened with
a soft detergent solution and wrung dry, then wipe dry with
• Make sure you insert the plug of the power cord all the way in
dry soft cloth.
the power outlet. Using the monitor with the power cord not
fully plugged in may cause heat to generate and cause a fire. • Do not use benzine, thinner or other chemical product on the
cabinet, as that may cause deformation and paint peeling.
• Do not use the monitor with the power cord wound or tied up.
Before using a chemical cloth, make sure to read all
Heat may generate and cause a fire.
accompanying instructions. Make sure that no plastic or
• When using an extension cord, be sure that the total current load rubber material comes in contact with the cabinet for a long
of all equipment connected to it dose not exceed the specified period of time, as that may cause damage or paint peeling.
ratings of the extension cord. If the rating are exceeded, heat may
generate and cause a fire. Make sure to carefully read the SERVICE
specifications accompanying the extension cord.
This unit is a precision instruments and if treated with care, will
Do not modify or open the cabinet provide years of satisfactory performance. However, in the event
of a problem, the owner is advised not to attempt to make
Never touch the inside of the monitor. High voltage circuits are
repairs or open the cabinet. Servicing should always be referred
inside, and there is a high risk of fire or electric shock if they are
to your dealer or Sanyo Authorized Service Centre.
touched. Any internal checks, settings, or repairs should be
performed by the dealer.
Do not place object inside the monitor
• Do not insert any metallic object through the ventilation grills.
• Do not stick metal objects (paper clips, hair pins, etc.), paper,
matches, etc., inside the monitor.
1
CONTENTS FEATURES
PARTS NAMES . . . . . . . . . . . . . . . . . . . . . . . 3 Equipped with video and audio input
terminals
CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . 5 The video and audio input terminals (two systems for each
input) allow bridge connections.
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . 6
Equipped with Y/C input (S-VIDEO input)
terminal
This terminal is used to input Y/C separation signals
(S-VIDEO signals).
Important (U. K. only)
Connect the mains lead to a suitable plug following the
colour code:
• Blue wire (Neutral) → to plug pin N or coloured black
• Brown wire (Live) → to plug pin L or coloured red
• Green and Yellow wire (Earth) → to plug pin E or “%”
Do not connect Blue and Brown wire onto plug pin E or onto
earth symbol “%”.
2
PARTS NAMES
Front Panel
7
POWER
VOLUME CONTRAST BRIGHT COLOUR
POWER
VOLUME CONTRAST BRIGHT COLOUR
2 3 4 5 6
1
1 SPEAKER
2 VOLUME control («)
For adjustment of audio volume.
3 CONTRAST control (»)
For adjustment of picture contrast.
4 BRIGHT control (ã)
For adjustment of picture brightness.
5 COLOUR control (õ)
For adjustment of colour enhancement.
6 Power button (POWER)
Press this button to turn the power on and off.
7 Power indicator
Lights when the power is on.
Note:
If the timing of display when you are using is not the same
factory or input timing you may need to adjust your
monitor.
3
PARTS NAMES
Rear Panel
AC INPUT Y/C TRAP
OUT VIDEO AUDIO
ON
OFF IN
IN OUT
HI LO HI LO
OUT
Y/C VIDEO IN
1 2 345 6 7 8 9FG
AC INPUT Y/C TRAP
OUT VIDEO AUDIO
ON
OFF IN
IN OUT
HI LO HI LO
OUT
Y/C VIDEO IN
1 AC INPUT socket 9 VIDEO OUT terminal (BNC-type)
Connect the AC power cord (supplied) securely to this Loop-throgh of the video in terminal.
socket and to a wall outlet. Connect to the video input terminal for VCR or another
monitor.
2 Y/C or VIDEO signal input/output switch
Select the input signal either VIDEO (BNC) or Y/C F AUDIO IN terminal (RCA jack)
(DIN jack). Connect to the audio output terminal of a VCR or other
equipment.
3 Y/C IN terminal (4-pin mini-DIN)
Connect to the Y/C separate output terminal of a video G AUDIO OUT terminal (RCA jack)
camera, VCR or other video equipment. Loop-throgh output of the audio in terminal.
Connect to the audio input terminal of a VCR or
4 Y/C OUT terminal (4-pin mini-DIN) another monitor.
Loop-through output of Y/C in terminal. Connect to the
Y/C separate input terminal of a VCR or another
monitor.
5, 7 HI/LO impeadance switch
When surveillance by single monitor please set the
impedance switch to 75 Ω, if several monitor
connected in series please set impedance switch to
75 Ω for the last monitor & others set to HI position.
6 TRAP filter switch (4.43 MHz) Y/C (Mini DIN 4 pin) terminal specification
For Model VMC-8414P only 4
OUT
3
Pin No. Signal
This switch is used to set the 4.43 MHz TRAP filter 1 GND (Y)
function ON/OFF. Set the TRAP filter switch to the ON 2 1
2 GND (C)
position to reduce the cross colour noise. 4 3
3 Y
2 1
8 VIDEO IN terminal (BNC-type) 4 C
IN
Connect to the video output terminal of video
equipment, such as a VCR or a colour video camera.
4
CONNECTION
Before making any connection, make sure all the devices are turned off.
Before making the connections, please refer to the instruction manual accompanying each device. If the devices are not
connected properly, that may cause a fire and/or damages.
Connections to the S-VIDEO terminals Basic connections
Monitor Video recorder Monitor Video recorder
: IN signal
: OUT signal
To S-VIDEO input terminal To Video To AUDIO
input terminal input terminal
Y/C
OUT VIDEO AUDIO
IN
IN OUT
OUT
IN
(Rear panel)
To Y/C input terminal To Video To AUDIO
input terminal input terminal
Video camera Monitor Video recorder Video camera Monitor Video recorder
Note: The components and connection cables are not included and must be purchased separately.
5
SPECIFICATIONS
Type Colour video monitor
Picture tube 14" 90˚ colour, P22 in line gun
Colour system PAL
Resolution 400 TV lines (VMC-8114P), 700 TV lines (VMC-8414P)
Normal scan 6 % over scan of picture tube effective screen area
Input terminals • Video in BNC connector (x1), 1.0 V (p-p) composite video signal, 75 Ω
• Audio in RCA jack (x1), 400 mV
• Y/C-separated: 1 line, mini-DIN 4-pin connector (x1)
Y: 1.0 V (p-p), 75 Ω/C: 0.3 V (p-p), 75 Ω (bridge connection possible)
Output terminals • Video out BNC connector (x1), loop-through switch change HI termination
• Y/C-separated OUT, mini-DIN 4-pin connector (x1), loop-through
• Audio out RCA jack (x1), loop-through
Audio power output 1W
Built-in speaker x1, impedance of 8 Ω
Power source AC 100 to 240 V 50/60 Hz
Power consumption 60 W (VMC-8114P), 80 W (VMC-8414P)
Operation temperature –10˚C to 50˚C (14˚F to 122˚F)
Storage temperature –20˚C to 65˚C (–4˚F to 149˚F)
Relative humidity 10 % to 90 %
Dimensions (W x H x D) 350 x 350 x 378 mm
Weight 14 kg
Accessary AC power cord x1
• Diagrams are shown for explanatory purposes only, and have been exaggerated, abbreviated or created as required, and so may
differ from the actual product.
• Features and specifications are subject to change without prior notice or obligations.
Dimensions
W D
H
6