Disclaimer: The information provided in this Brochure is only intended to give guidance in selecting and using Knauf products. While we make every effort to ensu- Knauf Contact re its accuracy, neither PT Knauf Gypsum Indonesia nor any of its employees or affiliates warrant or assume any legal liability or responsibility for the Technical Service : completeness or usefulness of any information regarding any apparatus, product, or process described in this Brochure or for any failure in installing ) 021 - 789 1661 or constructing any structure, installation or building or part thereof, caused by using this Brochure. Readers are advised to independently verify this in- formation prior to relying on it. In particular, readers must obtain appropri- @ www.knauf.co.id ate independent advice on the use of products in specific structures, instal- lations or buildings to ensure compliance with all regulations, including health and safety regulations. email@example.com INSTALLATION PROCEDURE Perimeter Frame UFC Upper Channel Insulation (if any) Install Knauf Angle Section (wall angle) Determine the distance Knauf UFC Upper Immediately after the order has been in accordance with the planned high frame in accordance with the planned installed and before installing the and screw with a maximum spacing ceiling weight. board, put insulation over the UFC 600mm and 50 mm from the edge / Attach the frame with UFC UFC Knauf frames. Make sure insulation is attached tip Bracket. tightly and neatly. Metal Section 03/2011 Suspension (Hanger) UFC Lower Channel Board Installation Knauf Soffit Cleat screwed on the top Install Knauf UFC Lower Frame in accordance All boards should be installed floor or building structural elements with the distance determined by the thickness perpendicular and meetings on the according to the distance which is determined by the load limit (see table). of the board that is used (see table), and then use Knauf Clip for UFC UFC Knauf bonds framework and screwed with Knauf gypsum board screws at 230mm KNAUF CEILING SYSTEM UNIVERSAL FURRING CHANNEL Put Threaded Rod on Soffit Cleat. Knauf between the upper and lower frames. spacing in the middle. Reduce the U-Bracket hanger can be used as an space the screws on the edge of the Knauf Ceiling System UFC or Universal Furring Channel, is an efficient and effective ceiling systems from Knauf. alternative to the distance between the board and become with distance The UFC system uses the minimum component types so to provide some added value in the form of ease of installation, ceiling and not on less than 125mm. abutmen 150mm. ease estimation, reducing waste material as well as optimal performance. UFC system components manufactured from mild steel with a standard galvanized coating refers to the design of ASTM A653 and ASTM C645 standard reference profile. PT. Knauf Gypsum Indonesia Knauf Hong Kong Ltd. Knauf Singapore Pte Ltd Cilandak Commercial Estate Unit 606A, Island Place Tower, 80 Marine Parade Rd #14 - 06 For ease of identification in the field / project, Knauf UFC has a special feature in the form of embossed triangle that Garden Centre 5th Floor, Suite 16 (B) 510 King’s Road, North Point, Parkway Parade also can increase the rigidity (stiffness) components. Jl. Raya Cilandak KKO Hong Kong Singapore 449269 Jakarta 12560, Indonesia Tel. : (852)2964-9311 Tel. : (+65) 6345 9233 Phone: (+62 21) 789 1661 Fax. : (852)2964-9313 Fax. : (+65) 6345 5465 Fax: (+62 21) 789 1662 E-mail : firstname.lastname@example.org E-mail : email@example.com Website : www.knauf.co.id, e-mail : firstname.lastname@example.org Website : www.knaufdrywall.co.uk Knauf Ceiling System - Universal Furring Channel Features • Using the framework of an efficient system. Smoke Fire Barrier Knauf U Bracket (One component to the main frame and Required if the ceiling is required according to the Building Usually used if the distance to Regulations regarding fire resistance, unless the ceiling is the slab above the ceiling does supporting frame.). in compliance with the requirements of fire resistance. not allow for the installation of • Using the clip (Clip UFC) is more solid and Threaded Rod. easy in application. Acces Panel Can easily be installed by installing additional Drop Ceiling • The number of minimal components, reducing framework. Can be made using the waste material and facilitate estimation. components and the UFC Section Angle Frame. • Embossing stamp the form to add strength Knauf Gypsum Plasterboard and easy identification of products. 1 layer or more Knauf Gypsum Plasterboard screwed to the UFC • Installation time is relatively short. Frame. Knauf UCF Clip Function Rugged design and easy to apply Used as forming the framework of Knauf ceiling. Bulk Head Can be made using the components Performance and the UFC Section Angle Frame. Knauf UFC Frame One component to the main frame Metal suspended ceiling components refer to and frame support. ASTM C645. Information Loading and Distance Framework installation based on ASTM C840 Load Class (kg/m2) Knauf UFC Frame [weight per unit area of the ceiling including grid and suspension] Lightweight galvanized metal products are used for ceiling and lining systems. Estimating Guide : 2.5 m’ per m2 ceiling (For gypsum plasterboard 12mm). 10 13 18 25 35 Dimension (mm) Detail Package Suspension Bracket/ T - Rod a 1200 1100 1000 900 800 Thickness Width Length Height Amount per kg/Package (±) Upper Channel b 1200 1100 1000 900 800 Spacing (A) (B) package 400 Thickness 9mm* B 3000 13.53 Board Lower Channel 0.455 35 22 10 600 4000 18.04 12mm* A *direction perpendicular to the installation of gypsum board under the UFC Frame Knauf UFC Clip Knauf Threaded Rod Components of galvanized mild steel with Hanger that comes with nuts and bolts on the double surface as a clamp for a better ceiling system. Knauf Angle Section holding capacity. Estimating Guide : 0.7 pcs m2 ceiling (For gypsum plasterboard 12mm). Lightweight galvanized metal products are used primarily in the framework of the perimeter of the ceil- Estimating Guide : 1.4 pcs per m2 ceiling (For ing system and lining. gypsum plasterboard 12mm). Dimensi (mm) Detail paket Knauf Soffit Cleat Thickness Width Length Height Amount per kg/Package (±) To bind Threaded Rod to structural soffit (A) (B) Package (upstairs). B Knauf UFC Bracket 0.40 25 3000 25 50 30.75 Anchored by Threaded Rod and can easily Estimating Guide : 0.7 pcs per m ceiling (For 2 gypsum plasterboard 12mm). A be set according to the distance and ease in leveling ceiling. Estimating Guide : 0.7 pcs per m2 ceiling (For gypsum plasterboard 12mm). Knauf Universal Bracket Alternative hanger components are bolted directly to structural elements.
Pages to are hidden for
"KNAUF CEILING SYSTEM"Please download to view full document