SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
FAILURE TO PROVIDE ALL OF THE INFORMATION REQUIRED BELOW MAY
RENDER YOUR PROPOSAL INELIGIBLE FOR AWARD
WRECKER, BOOM-UNDERLIFT
The purpose of this questionnaire is to determine the suitability of your equipment to satisfy the requirements as stated in the
specification. YOU MUST PROVIDE A RESPONSE TO ALL QUESTIONS. Failure to provide a response may result in
the rejection of your proposal.
GENERAL INFORMATION REQUIRED
Personnel Responding to Questionnaire:
Name
Title
Company Responsibility/Position
Telephone/Fax Numbers
E-mail address
Mailing Address
Units: The data provided in the TIQ shall be in English units, unless otherwise specified. Metric units may be provided if
clearly defined and identified.
All written information shall be in English.
In addition to responding to the questions below, the offeror shall provide the following:
(a) Vehicle and major component commercial literature or specification sheets, brochures or any other information that
would substantiate the information provided. If your commercial literature does not provide information relating to a
particular question, you are required to provide a written explanation of your ability to meet that particular requirement
with your written proposal.
(b) Identification of all modifications or redesigns to the previously manufactured base vehicle necessary to meet the
requirements of the specifications. The offeror shall also explain in detail the reasons for the modifications or redesigns.
In addition to responding to the questions below, the offeror shall provide the following:
(c) Vehicle and major component commercial literature or specification sheets or any other information that would
substantiate the information provided. If your commercial literature does not provide information relating to a particular
question, you are required to provide a written explanation of your ability to meet that particular requirement with your
written proposal.
(d) Identification of all modifications or redesigns to the previously manufactured base vehicle necessary to meet the
requirements of the specifications. The offeror shall also explain in detail the reasons for the modifications or redesigns.
(e) US Federal Motor Vehicle Safety Standards (FMVSS) can be obtained at the following website:
http://www.access.gpo.gov/nara/cfr/waisidx_04/49cfr571_04.html
(f) Australian Design Rules (ADR) can be obtained at the following website:
http://www.dotars.gov.au/roads/motor/design/adr_online.aspx
(g) European standards (United Nations Economic Commission for Europe, ECE) can be obtained at the following website:
http://www.unece.org/trans/main/wp29/wp29regs1-20.html
(h) European Economic Community (EEC) directives can be obtained at the following website:
http://eur-lex.europa.eu/en/index.htm
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
1 of 10
SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
Information Notes:
(a) For components procured by the vehicle manufacturer, the component manufacturer’s name and model or part number
shall be shown.
(b) Curb weight shall be weight of vehicle offered, completely equipped with all standard equipment, all recovery equipment
and accessories, coolant, fuel and lubricants, less the weight of the crew (175 pounds per person). Weight distribution
empty shall be based on curb weight.
(c) Gross Vehicle Weight (GVW) shown shall include curb weight of the vehicle, weight of the crew (350 pounds total), and
the payload. Weight distribution loaded shall be based on GVW.
(d) Payload shall include the weight transferred to the towing vehicle from the maximum towed load during lift-tow.
(e) Gross Combination Weight (GCW) shown shall include curb weight of the vehicle, total weight of the crew (175 pounds
per person), and the maximum towed load.
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
2 of 10
SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
WRECKER, BOOM-UNDERLIFT
1. CONFIGURATION
(a) Is the vehicle provided with all new parts? Unanswered
(b) Is this vehicle a 2008 model or later? Unanswered
1) Is the vehicle provided a 4x4 wrecker (tow truck)? Unanswered; If yes: Make Model
Comments
2. SAFETY
(a) Does this vehicle meet the following US Federal Motor Vehicle Safety Standards (FMVSS) if applicable to your
proposal? Unanswered
1) Indicate which of the following FMVSS are met, and provide a brief description of how they are met or indicate
why they are not applicable:
FMVSS Number Brief description
101 Unanswered
102 Unanswered
103 Unanswered
104 Unanswered
106 Unanswered
111 Unanswered
113 Unanswered
119 Unanswered
120 Unanswered
121 Unanswered
124 Unanswered
201 Unanswered
203 Unanswered
204 Unanswered
205 Unanswered
206 Unanswered
207 Unanswered
208 Unanswered
209 Unanswered
210 Unanswered
212 Unanswered
219 Unanswered
301 Unanswered
302 Unanswered
2) If the vehicle does not meet FMVSS standards, which vehicle safety standards does the vehicle comply with?
Unanswered; If the vehicle meets ECE, EEC, ADR, and/or JIS describe in detail which standards are met that
are applicable to your proposal
(b) Are airbags provided? Unanswered; If yes, is there a procedure to de-activate all airbags? Unanswered. Describe
procedure
Comments
3. STANDARD EQUIPMENT
(a) Is the vehicle equipped with: Interior dome light? Headlights Brake lights Taillights Turn signals Back
up lights Other Describe
1) Daytime running lights? Unanswered; If yes, can they be disabled? Unanswered
(b) Is the vehicle supplied with a windshield wiping and washing system? Unanswered
(c) Is the vehicle supplied with exterior rearview mirrors? Unanswered
(d) Is the vehicle provided with door locks and ignition identically keyed for all vehicles? Unanswered; Number of keys
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
3 of 10
SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
(e) Is the vehicle provided with anti-sail mud flaps? Unanswered; Describe
(f) Is the vehicle provided with a visual and audible back-up alarm? Unanswered; Describe
(g) Are there two 5-gallon or two 10 20-liter jerry cans for diesel fuel with mounts and securing equipment provided?
Unanswered; Location
1) Are all jerry cans labeled in both English and the language specified in the contract or universal symbols for the
diesel fuel and permanently affixed to the cans? Unanswered
2) Do their locations interfere with the operations of the recovery equipment? Unanswered.
(h) Is an ABC type fire extinguisher provided with mounting bracket? Unanswered; Capacity lbs; Does its location
interfere with the operations of the recovery equipment? Unanswered; Location
(i) Is the vehicle provided with a heavy-duty full-width front push bumper and or full-width grill guard? Unanswered;
Describe
(j) Is the vehicle provided with tow hooks or eye(s) mounted on the front of the vehicle? Unanswered; Quantity
Describe
(k) Is the vehicle provided with trailer towing provisions? Unanswered; If yes:
1) Pintle? Unanswered; If yes: Manufacturer ; Model ; Capacity pounds
2) 2-inch ball? Unanswered; Describe towing provision and towing capacity of vehicle as equipped
(l) For vehicles shipping to Iraq:
1) Are all instructions, diagrams, and warning labels bilingual in both Arabic and English or universal symbols?
Unanswered
(i) Are they permanently affixed to the vehicle? Unanswered
2) Are fuel filler caps or an area near the fuel filler cap provided with labels stating type of fuel that is compatible with
the vehicle in both Arabic and English, or universal symbols? Unanswered
3) Are manuals provided for each vehicle in both Arabic and English provided? Unanswered
4) Do all manuals contain an amendment in both Arabic and English stating the ability to operate in very high sulfur
content diesel fuel (10,000 ppm or 1%)? Unanswered
(m) For vehicles shipping to Afghanistan:
1) Are all instructions, diagrams, and warning labels bilingual in both Dari and English or universal symbols?
Unanswered
(i) Are they permanently affixed to the vehicle? Unanswered
2) Are fuel filler caps or an area near the fuel filler cap provided with labels stating type of fuel that is compatible with
the vehicle in both Dari and English or universal symbols? Unanswered
3) Are manuals provided for each vehicle in both Dari and English? Unanswered
4) Do all manuals contain an amendment in both Dari and English stating the ability to operate in very high sulfur
content diesel fuel (10,000 ppm or 1%)? Unanswered
Comments
4. RATINGS
(a) Are the ratings for the vehicle the published ratings at the time of the offer? Unanswered
(b) Have any of the component ratings been raised to meet the requirements? Unanswered
(c) Are the following individual components rated at the GVW or GCW (whichever is greater) specified for the vehicle
(yes/no and provide supporting data)?
1) Engine Unanswered -
2) Transmission Unanswered -
3) Axles Unanswered -
4) Suspension Unanswered -
5) Tires Unanswered -
Comments
WEIGHTS (see Informational Notes on first page) (pounds):
(d) Curb weight (chassis and body total)
Weight distribution:
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
4 of 10
SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
1) Curb weight, front axle
2) Curb weight, rear axle
(e) Weight of crew (175 lb per person)
(f) Towing capacity
(g) GVW (total of (d), and (e) above)
Weight distribution:
1) GVW, front axle
2) GVW, rear axle
(h) GCW (total of (d), (e), and (f) above)
Weight distribution:
1) GCW, front axle
2) GCW, rear axle
(i) Maximum payload (under lift or boom ) pounds at inches from rear of body
Comments
DIMENSIONS (inches):
(j) Wheelbase (front axle to rear axle)
(k) Track (width from center-to-center of outermost tires):
1) Front axle
2) Rear axle
(l) Frame length back of cab
(m) Rear of cab to rear axle
(n) Rear axle to rear of body
(o) Pintle (or ball) height from ground
(p) Overall: Length ; Width (excluding mirrors) Height (at curb weight)
(q) Ground clearance
Comments
5. ENGINE
(a) Can the vehicle be operated on very high sulfur content diesel fuel (10,000 ppm or 1%)? Unanswered
1) If so, please describe any degradation in performance from operation on very high sulfur content diesel (10,000
ppm or 1%)
2) Is the vehicle configured for an export market? Unanswered
3) Is the vehicle’s engine turbocharged? Unanswered
4) Manufacturer Model Model year ; Number of cylinders ; Displacement cu. in.;
Net horsepower at engine governed speed rpm; Maximum net torque (ft-lb) at rpm
Please provide engine power and engine torque output curves (versus RPM)
(b) Is the vehicle equipped with:
1) An Exhaust Gas Recirculation (EGR) valve? Unanswered
2) A Diesel Particulate Filter (DPF)? Unanswered
3) A Diesel Oxidation Catalyst (DOC)? Unanswered
4) Any other emission control devices not listed above? Unanswered; If yes, please list other emission control
devices
(i) Did the vehicle have any emission control devices removed after it was manufactured? Unanswered; If
yes, what devices have been removed (check all that apply)? EGR valve DOC DPF Other,
please list
(ii) Are all details of the modifications that were required to remove the emission control devices provided?
Unanswered; If yes, describe
(iii) Has the computer that monitors and controls engine function been reprogrammed? Unanswered. If yes,
describe
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
5 of 10
SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
(iv) Have any other vehicle modifications and/or alterations been made to allow the vehicle to operate on very
high sulfur content diesel fuel (10,000 ppm or 1%)?Unanswered. If yes, list the vehicle modifications or
alterations
(v) Did the vehicle manufacturer verify and approve all modifications or alterations made to the vehicle
including removal of emission control devices? Unanswered. If yes, is documentation provided?
Unanswered
(vi) If modifications or alterations will be performed, who will be making them?
(c) When operating on very high sulfur content diesel fuel (10,000 ppm or 1%), is the maintenance and/or service
schedule for the vehicle provided and included in the vehicle manual? Unanswered
(d) Is the engine provided with the heaviest-duty available cooling and air filtration system designed for a dusty, desert
environment (+120 °F air temperature) provided? Unanswered
1) How is the engine cooled?
2) Provide description of cooling system (including transmission cooler, if applicable)
3) Describe the air filtration system
Comments
6. CHASSIS/DRIVELINE/AXLES/SUSPENSION
(a) Are the heaviest-duty available springs, shocks, and axles provided? Unanswered
(b) Are lockable differential(s) or limited slip differential(s) provided? Unanswered; If yes:
1) Does the traction control engage automatically or by the driver without leaving the driver’s position?
Unanswered
CHASSIS:
(c) Provide a schematic or brochure showing the vehicle layout or design
1) Chassis: Manufacturer Model Year Configuration Unanswered
DRIVELINE:
(d) Are all drivelines the same for all vehicles? Unanswered
AXLES:
(e) Are all rear axle ratios the same for all vehicles? Unanswered
1) Gear ratios
2) Front: Manufacturer Model Load rating pounds
3) Rear: Manufacturer ; Model Load rating pounds
SUSPENSION:
(f) Front: Type Load rating pounds; Manufacturer Model
(g) Rear: Type ; Load rating pounds; Manufacturer ; Model
Comments
7. TRANSMISSION
(a) Type Unanswered; Manufacturer Model Number of speeds: Forward Reverse Provide
all transmission gear ratios Input torque capacity pound-feet
1) Is a secondary transmission oil cooler provided? Unanswered; If yes, describe
(b) Is the vehicle provided with a two-speed transfer case? Unanswered; If yes: Manufacturer Model All
gear ratios ; Input torque capacity pound-feet.
Comments
8. STEERING
(a) Is the vehicle left hand drive? Unanswered
(b) Is the vehicle equipped with power steering? Unanswered
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
6 of 10
SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
Comments
9. BRAKES
(a) Is the vehicle provided with four separate brake systems? Unanswered
(b) Service: Type Size: Front Rear ABS provided? Unanswered
1) Are the service brakes an air brake system?
(i) Are they provided with an air dryer? Unanswered
(c) Emergency brake? Unanswered
(d) Relief (i.e. engine or exhaust brake)? Unanswered; If yes, describe
(e) Parking brake: Type Axles operated on
Comments
10. TIRES AND RIMS
(a) Is the vehicle provided with tubeless, on-off road, radial tires? Unanswered
1) Tires: Manufacturer ; Model ; Size and load rating: Front Rear Spare
2) Total vehicle tire capacity (pounds)
(i) Front axle capacity (pounds)
(ii) Rear axle capacity (pounds)
(iii) Spare tire capacity (pounds)
3) Rims: Manufacturer Model
(b) Is the vehicle provided with a full-size spare wheel and tire assembly with holder? Unanswered
1) Does the location of the spare wheel and tire assembly interfere with normal vehicle operation? Unanswered
(c) Are all tires and rims interchangeable including the spare and are they the same load rating? Unanswered
Comments
11. ELECTRICAL
(a) Is the electrical system a 12 or 12 and 24 dual volt system? Unanswered
1) If the system is 12 and 24 volt, are the following circuits 12 volts?
(i) 20 amp circuit for communication equipment in the cab Unanswered
(ii) All vehicle exterior lighting Unanswered
(iii) SAE J560 - 7 pin connector for towing trailers Unanswered
(b) Is a SAE J560 - 7 pin connector for towing trailers provided? Unanswered
(c) Is the vehicle equipped with at least two heavy-duty maintenance free batteries? Unanswered; Quantity
(d) Is the vehicle equipped with a heavy-duty alternator? Unanswered
(e) Is the vehicle provided with a light bar or beacon(s) permanently mounted? Unanswered; If yes: Type Unanswered
Manufacturer Model Color Location
(f) Is the vehicle provided with work lights and rear hookup lights? Unanswered; Describe
(g) DELETED
Comments
12. CAB
(a) Type Unanswered; Material Fully enclosed? Unanswered; Number of doors
(b) Is the vehicle provided with seating for the driver and minimum one passenger? Unanswered; Seating capacity
(c) Are seatbelts provided for all cab occupants? Unanswered
(d) Is the vehicle provided with a heavy duty air conditioning, and heating and defrosting systems? Unanswered
1) Is the air conditioning system designed for operation in dusty, desert environments (+120°F)? Unanswered
(e) Are the controls for the light bar or beacon(s) provided in the cab and accessible to the crew (driver and front seat
passenger(s))? Unanswered; Location
Comments
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
7 of 10
SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
13. COLOR
(a) Is the exterior of the vehicle:
1) Desert tan 686, color chip 33446, or equivalent, as specified? Unanswered
2) Holly green, color chip 14090, or equivalent, as specified? Unanswered
3) White, color chip 17925, or equivalent, as specified? Unanswered
(b) For Afghanistan only: Is the vehicle provided with high-performance non-reflective decals? Unanswered; If yes:
Quantity Location(s) Size(s) Type of decal Unanswered Material
1) Do the decals depict the logo shown in paragraph 13.2.1 with the word “Police” in both English and Dari below
the logo? Unanswered
2) Are the decals scaled properly with the largest size that can be placed on the required surfaces? Unanswered;
Size of decals
3) Are the decals securely affixed or adhered to the vehicle, have a smooth surface with no air pockets?
Unanswered;
(i) What is the life expectancy of decals years
4) Are the decals designed such that once applied they cannot be easily removed in one piece? Unanswered
Comments
14. PERFORMANCE
(a)What is the minimum temperature the vehicle can be stored, started and operated in? F
(b)What is the maximum temperature the vehicle can be stored, started and operated in? F
(c)Can the parking brake hold the vehicle on a 20% longitudinal slope at GVW? Unanswered
(d)Is the vehicle capable of shallow water fording without a kit? Unanswered; If yes, at what depth? inches
(e)Is the vehicle capable or operating 50% of mission on paved roads, 40% on unpaved roads or trails and 10% off
road? Unanswered
(f) At GCW, is the vehicle capable of:
1) Maintaining a speed of at least 30 mph on a 2% longitudinal slope? Unanswered
2) Maintaining an average speed of not less than 25 mph on sandy roads or trails? Unanswered
3) Operating on a 20% side slope? Unanswered
4) Climbing and descending a 40% longitudinal slope at a minimum speed of 2.5 mph? Unanswered
(g) At curb weight, is the vehicle capable of:
1) Maintaining a speed of at least 55 mph on a level highway? Unanswered
2) Operating from integral fuel tank(s) for at least 325 miles on highway surfaces at an average speed of not less
than 40 mph? Unanswered; Actual distance
3) What is the stopping distance from 20 mph? feet
Comments
15. RECOVERY EQUIPMENT AND BODY
Provide a brochure of the recovery body and a schematic showing the recovery body and equipment layout, design and
storage provisions
(a) Recovery body: Manufacturer Model Year
(b) Is an integrated boom-underlift system or is a separate boom and underlift systems provided? Unanswered
(c) Tow rating pounds
(d) Underlift equipment: Manufacturer Model Type
1) Is a power tilt, extension, elevation, and fold provided as defined by SAE J2512? Unanswered
2) Lifting capacity:
(i) Retracted pounds at inches reach
(ii) Extended pounds at 68 inches from the rear of the vehicle
(iii) Fully extended pounds at inches reach
3) Tilt angle: Above horizontal degrees; Below horizontal degrees
4) Are there means to secure a vehicle onto the underlift?
(e) Wrecker boom: Manufacturer Model Type
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
8 of 10
SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
1) Is a power boom extension provided? Unanswered; If yes: Extended length in.
2) Range of the boom working angle degrees
3) Lifting capacity at 0° boom elevation:
(i) Retracted pounds at inches reach
(ii) Extended pounds at inches reach
4) Lifting capacity at 30° boom elevation:
(i) Retracted pounds at inches reach
(ii) Extended pounds at inches reach
5) Lifting height (maximum elevation) inches at degrees
6) Boom reach past tailboard:
(i) Retracted inches
(ii) Extended at minimum elevation inches at degrees
(iii) Extended at maximum elevation inches at degrees
7) Boom mounted recovery winch:
(i) Rated capacity (first layer bare drum) pounds
(ii) Cable diameter inches
(iii) Cable length inches
(iv) Remote control provided Unanswered; If yes: Distance of operation ft
(f) Tow sling provided? Unanswered; If yes: Manufacturer Model Rating pounds
(g) Storage compartments:
1) Number of compartments Dimensions: Height Length Depth
2) Are the compartments water-resistant? Unanswered
3) Are the compartments lockable? Unanswered
4) Are all compartment locks identically keyed? Unanswered; Number of keys provided
5) Is there sufficient capacity to store all provided equipment and accessories? Unanswered
6) Are the following tools and accessories provided, with dedicated stowage in the storage compartments?
(i) Standard tools required for simple operator level maintenance? Unanswered
Wrench and socket set Screwdrivers Adjustable wrench Pliers Hammer; Other tools (list)
(ii) Tire changing tools and a lifting jack Unanswered; Capacity of jack tons
(iii)Red emergency reflective triangles Unanswered; How many?
(iv) First Aid kit Unanswered
(v) Hose and fittings to inflate tires from vehicle’s compressed air system Unanswered; If yes: Hose length
ft; Describe fittings provided
(vi) Clevis hooks Unanswered; Size inches; Rating pounds
(vii) Snatch blocks Unanswered; Size inches; Rating pounds
(viii) Wheel chocks Unanswered; How many?
(ix) Tow light kit Unanswered; Manufacturer Model number Electrical cable length
(x) Which of the following jacks are provided? Sand jack Airbag jack
(xi) Safety chains Unanswered; Quantity Capacity tons
(xii) Anchor shackle Unanswered; Quantity ; Capacity tons
(xiii) Underlift fork attachments (if provided): Unanswered; If yes, describe
(xiv) Additional lifting or towing accessories provided (list and describe)
(h) Controls: Are dual controls for the recovery equipment provided? Unanswered; Locations
1) Are enclosures lockable and waterproof? Unanswered; Describe
(i) Are all enclosures keyed alike? Unanswered; If yes, number of keys provided
2) Are enclosures lighted or are individually lighted controls for nighttime operation provided? Unanswered; If
yes, describe
3) Are all controls marked in English and the language specified in the contract or labeled in Universal symbols?
Unanswered, if yes, describe
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
9 of 10
SOLICITATION W56HZV-10-R-G004
TECHNICAL INFORMATION QUESTIONNAIRE
AMENDMENT 0003
Mar 11, 2010
(i) Are hydraulic vehicle positioning dollies Is a towing dolly provided? Unanswered; If yes: Storage location
Manufacturer Model Quantity N/A Rating pounds
(j) Are hydraulics powered by an engine a gear driven PTO? Unanswered
1) Pump flow rate gallons per minute
2) Oil reservoir size: gallons
Comments
16. RADIO FREQUENCY IDENTIFICATION (RFID) TAGS
(a) Is each vehicle or item and associated lot of spares tagged with a removable active RFID tracking tag? Unanswered
1) What is the National Stock Number (NSN) of the removable RFID tracking tag?
2) Is the removable active RFID tracking tag readable from at least 200 ft.? Unanswered
3) RFID tracking tag manufacturer ; Model number ; Year manufactured
(b) Where is the RFID tag located on the vehicle?
(c) How is the tag affixed to the vehicle or item and associated lot of spares?
(d) Will the tag’s electronic format be in compliance with the Joint Total Asset Visibility (JTAV) specification, version
2.0, section 3.4.1 format? Unanswered
(e) Will the Document field be programmed with the document number (e.g. “milstrip”) provided by the Government
agency? Unanswered
1) Will the “document field” titled “DOCUMENT” be the document number as specified by the Government
procuring agency? Unanswered
2) Will the MISC1 field be programmed with the item serial number, if available? Unanswered
3) Will the MISC2 field be programmed or reserved for comments (e.g. contract number)? Unanswered
4) Which company or agency will “write to” or “program” the tag?
Comments
17. DEALER SUPPORT - AFGHANISTAN
(a) Is there a dealer support in Afghanistan, as required by paragraph C.3 of the solicitation? Unanswered
(b) Dealership name
(c) Point of Contact
(d) Address (include country)
(e) Phone
(f) Email
Website (if any)
18. DEALER SUPPORT - IRAQ
(a) Is there a dealer support in Iraq, as required by paragraph C.3 of the solicitation? Unanswered
(b) Dealership name
(c) Point of Contact
(d) Address (include country)
(e) Phone
(f) Email
Website (if any)
SOURCE SELECTION SENSITIVE, SEE FAR 3.104
10 of 10