Tech. & Data Sheet
ACRYLIC LATEX CONCRETE STAIN
PRODUCT NAME where this is a problem, a non-skid Unpainted or badly worn surfaces:
additive should be either mixed into or Touch up badly worn spots on wood
ACRYLIC LATEX broadcast on the finish before it is with a thinned first coat of INCRETE
CONCRETE STAIN allowed to dry. ACRYLIC LATEX CONCRETE
STAIN Thin with 1 cup of water
MANUFACTURER & DISTRIBUTOR % Solids (Volume) 26±1 to 1 quart of stain for the first coat.
OF INDUSTRIAL CHEMICALS % Solids (Weight) 37±1 Apply the second coat without
8509 SUNSTATE ST. thinning.
Recommended Dry Film
TAMPA, FLORIDA 33634
(813) 886-8811 (Per Coat): 1-2 mil RECOMMENDED USES
For interior and exterior surfaces
PRODUCT DESCRIPTION Mils DFT such as patios, floors, porches,
ACRYLIC LATEX CONCRETE Viscosity: 1360-1500 cps walks, or wherever an outstanding
STAIN is a water-based, blend of abrasion resistant coating is desired.
Dry Time @ 75oF. 0.5-1 hr STT
the finest acrylic resins and pigments Can be used on floors of garages,
available which gives this product Recoat in 2-4 hours carports, driveways, or other areas
superior adhesion, good resistance Flammability Non Flammable where automobiles will stand.
to wet and dry abrasion, excellent Warm or hot tires could cause lifting
color fastness, and excellent SAFETY of the stain film from the surface of
resistance to acid and alkali. No special protection required. the concrete if proper penetration
Use normal industrial protection was not achieved.
Preparation: Before application of equipment when handling material.
any new coating, dirt, grease, grime, In case of spill, absorb with inert APPLICATION
any foreign materials should be material and dispose of in Brush, Roll, or Spray. A 3/8”
removed and all exterior surfaces accordance with application nap roller is recommended on
should be treated for mildew. It is regulations. smooth surfaces, a ½” to 1” nap is
imperative to etch concrete properly, recommended for rough surfaces.
especially very smooth and dense RECOMMENDED THINNER For spraying, use a tip designed
concrete. INCRETE ACRYLIC LATEX for application of bodied paints
CONCRETE STAIN does not or contact a representative from
Application: Mix product thoroughly require thinning, except for the Increte Systems.
Apply with brush, roller, or spray. first coat on unpainted concrete.
Apply when surface temperatures Should thinning become necessary, RESISTANCE TO
o
are at least 50 F. Mask off baseboards clean drinking water should be
and walls. Paint a 3” border around Dry Heat Excellent
added only to achieve the required
the edge while working. Begin at the properties. About 1-2 pints of fresh Alkali Excellent
corner farthest from the door. water should be added per gallon
Saturate the roller with paint and lay Yellowing Excellent
of paint for the first coat on new
it out in bold, criss-cross strokes, concrete. Weather Excellent
then make straight even strokes
Moisture Excellent
to smooth out the paint film. Roll into RECOMMENDED PRIMER
freshly brushed borders. Bring roller Cement: New, unpainted, or Industrial Fumes Very Good
down lightly over wet paint in smooth smoothly-worn concrete should Mildew Excellent
even strokes. Work from dry area into be etched with a solution of 1 part
wet areas in 3 feet sections. Do not muratic acid to 8 parts water. COVERAGE
thin with paint thinners. Tint only with Let stand 30 minutes. Scrub surface Coverage will depend on porosity
recommended colorants. Do not allow with a brush or stiff broom while and contour of the surface to be
water to stand on newly painted rinsing to remove all residue. 2
coated. 117 ft. per gallon at 2 mil
surface for one week. Let dry. Apply 2 coats of INCRETE DFT. The actual coverage will be
Since this type of finish may become ACRYLIC LATEX CONCRETE less depending on application and
slippery when wet or when oil or STAIN with the first coat thinned 2
color. Apply at 300-400 ft. per
grease is on the surface, in areas back with water at the ration of 1 gallon.
pint of water to 1 gallon of stain.
FINISH: Low Luster
VEHICLE TYPE: Acrylic Resins
PIGMENT TYPE: Titanium Dioxide
& Inert Pigments
SOLVENT TYPE: Water
FLASH POINT: Not Flammable
NOTES
Clean tools and equipment with
soap and water. Store and maintain
spray equipment as directed by
the manufacturer. This type of a
finish could become slippery when
wet or when oil or grease is on the
surface. In areas where this could
be a problem, a non-skid additive
should be either mixed into or
broadcast on to the finish before it
is allowed to dry for added traction.
PACKAGING
1 gallon can, 5 gallon pail.
IMPORTANT NOTICE
THESE PRODUCTS ARE SOLD
SUBJECT ONLY TO THE
EXPRESSED WARRANTIES
CONTAINED HEREIN. ADDITIONAL
WARRANTIES, EXPRESSED OR
IMPLIED, AND ANY WARRANTY OF
MERCHANT ABILITY IS HEREBY
EXCLUDED. BUYER AGREES THAT
SELLER ASSUMES NO LIABILITY
FOR CONSEQUENTIAL DAMAGES
OF ANY KIND WHICH RESULT
FROM THE USE OR MISUSE OF THE
MERCHANDISE SOLD HEREUNDER.
IN THE EVENT THAT THE BUYER
PROVES THAT ANY GOODS
RECEIVED DO NOT CONFORM TO
THE SPECIFICATIONS AGREED TO
BETWEEN THE PARTIES OR IF THE
BUYER PROVES THAT SUCH
GOODS WERE DEFECTIVELY
MANUFACTURED. THE BUYER’S
REMEDIES SHALL BE LIMITED TO
EITHER THE RETURN OF THE
GOODS AND REPAYMENT OF THE
PURCHASE PRICE OR
REPLACEMENT OF THE NON-
CONFORMING GOODS AT THE
OPTION OF THE SELLER. SUCH
REMEDY BEING EXCLUSIVE OF ALL
OTHERS AND THE SOLE REMEDY
AVAILABLE TO THE BUYER,
HEREBY EXPRESSLY WAIVES ANY
CLAIM TO ADDITIONAL DAMAGES.