Data Descrip 1991 2004 by nZmi1d77

VIEWS: 166 PAGES: 4169

									                                                         all


discription
employee #1 and a crew had driven 32 wood piles and were changing the configuration of the handles to drive a steel pile. It wa
employee #1, a crane operator, was traveling down a 12 percent grade for several miles. He was unable to slow down the cran
at 10:30 a.m. on may 15, 1993, employee #1, a construction worker, was struck and killed by an out-of-control truck that swerv
employee #1 entered a confined space with a lighted torch. The atmosphere was not tested and contained an explosive concen
employee #1 was leaving the job site at the end of his shift when he drove through a stop and warning sign and was struck by a
employee #1 was attempting to nail into a truss spreader board while kneeling on the truss. The spreader board gave way and
while descending from a concrete form, employee #1 slipped and fell approximately 30 feet. The employee was wearing a work
employee #1 was installing a control wire for the electronic controls of a ventilation in a potato storage warehouse. He was work
employee #1 was working as a flagman on a county road that was being chip sealed. She had just moved to a new location and
on the morning of may 3, 1995, employee #1, an excavator, was digging up the sewer line to a single family home that employe
employee #1 was operating a 1967 caterpillar 1299e road grader, serial #13182, to clean a drainage ditch along the side of a m
on the morning of july 2, 1991, employee #1 and several coworkers started removing roofing material from a single-story struct
at approximately 1:45 p.m. on april 27, 1992, employee #1 was about 20 ft above ground inside a scissor lift working on an exp
on december 9, 1991, employee #1 was operating a 25 ton link belt rough terrain crane, serial #4569354. The crane tipped ove
employee (3.1) above was thown between a piling and an 8,000 lb mat when the crane slipped (crawled) off a mat in the rear.
employee #1 owner of riverdale electric co inc was working from an elevator sucket on a reach see aerial lift (model 6000 serie
on sunday, january 21, 1990, at approximately 5:10 a.m., employee #1, a licensed tankerman, was employed by riverside marin
employee #1 and a coworker, both ironworkers, were installing sections of 3 ft wide by 11 ft 8 in. long, 1 1/4 in. thick corrugated
at about 2:10 p.m. on march 11, 1990, employees #1, #2, and #3 had been using electric skilsaws to cut and remove a damage
at about 2:10 p.m. on march 11, 1990, employees #1, #2, and #3 had been using electric skilsaws to cut and remove a damage
at about 2:10 p.m. on march 11, 1990, employees #1, #2, and #3 had been using electric skilsaws to cut and remove a damage
at approximately 11:35 a.m. on august 30, 1990, employee #1, a road flagman, was struck by a 1977 black ford pickup truck, v
at approximately 5:45 p.m. on december 22, 1990, employee #1 was installing dust collectors in the sab construction area. As t
about 5:30 p.m. on november 16, 1990, employee #1 and two coworkers were installing a new steam condensation pipe in the
at 10:30 a.m. on december 8, 1990, the single window and the door of a 9 ft by 11 ft room were covered with polyvinyl because
at 10:30 a.m. on december 8, 1990, the single window and the door of a 9 ft by 11 ft room were covered with polyvinyl because
employee #1 was struck by a forklift and crushed against a concrete support structure. He died of massive internal injuries with
employee #1 and coworkers were carrying wheelbarrows and climbing a wooden ladder to the second floor of a building where
an employee was directing the movement of a concrete bucket towards a rubbish pile. The concrete bucket was being moved b
an electrician was troubleshooting new wiring. No lockout or tagging procedures were in place while he was working, and the w
at approximately 8:00 a.m. on march 28, 1995, employee #1 was walking to a roof edge to weld a bent plate at an airport expan
an electrician working for an electrical contractor at a new retail store construction project was removing temporary electric cab
employee #1 was acting as a rigger and handler for crates of plate glass being lifted out of a shipping container. On the sixth lif
at approximately 9:00 a.m. on july 17, 1993, employee #1 was feeding abbaca fiber rope from a wooden spool into a 4 inch pvc
employee #1, a diver, was cutting down the interior bulkhead of a compartment that extended from the main deck to the keel. T
employee #1 was installing modular building units raising/lowering with a simplex jack. The employee walked in between two of
at approximately 10:00 a.m. on june 10, 1996, employee #1 and a coworker were loading garbage into the back of a mitsubishi
a boom truck operator began driving the truck out of a substation while the hydraulic boom on the truck was still extended. The
a supervisor instructed one of his electricians to troubleshoot a lighting circuit. The employee got a 3-meter-tall ladder, climbed
three employees were working in a 1.4-meter-deep excavation at an airport. They were preparing the foundation for the installa
employee operating roller, got off to try and removew marker to avoid being run over by a dump truck backing up to unload grav
employee on top of 3 tiered mobile scaffold. Scaffold moved while employee was on scaffold. Scaffold collapsed and employee
on august 21, 1998, at approximately 2:30pm, employee #1 and #2 were preparing to load a 580e case backhoe into a 40 foot
at approximately 7:50 a.m. on november 14, 1993, employee #1 was removing a plastic tarp that was hanging from the sixth le
employee #1, the sole owner of a masonry company, was in a scenic mountain town with employee #2, his brother-in-law, a se
on friday, september 8, 1995, employee #1, a bulldozer driver with asircc, inc., was taking a lunch break. Employee #1 had said
on april 29, 1996, employee #1 was at a job site when he died of cardiac arrest due to coronary artery blockage. He also had a
on 11-06-97 at approximately 1:30pm a 50 year old hispanic male, was crushed to death when the extended boom of a concre
employee #1 was inspecting a tubular welded scaffold before work was to begin installing bricks on a residential building. The e
employee #1 was working and observing in an area in which a coworker was operating a texoma hole digger. When the auger
a tub in an old house was not draining properly, and two employees were working on the plumbing problem. One of the employ


                                                      Page 1
                                                         all


employee #1 and a coworker, both iron workers, were rigging structural steel beams that were to be hoisted by crane from a tru
employee #1 was spray painting a condominium when he fell approximately 25 ft from a small roof section. He fractured his sku
employee #1 was 315 ft high performing maintenance on a tv tower employee #1 thought he had attached his safety belt prope
employee #1 was operating a power sweeper on a flat roof. He was backing up and walked off the roof, falling to the ground. H
an apprentice electrician was working under the guidance of a journeyman electrician. The electrician instructed the apprentice
employee #1 and a coworker, both surveyors, were marking center line stations at 50 feet intervals on a highway. The coworke
employees placed two hydraulic jacks on either side of a 22 ft long wooden, glue-laminated beam to take the weight off the vert
employee #1, a 35-year-old excavating company vehicle operator, was having his caterpillar 769c dump truck loaded with rock
the owner of a house moving company and his two sons were moving a house on a mack diesel truck, model #b87. While they
a coworker was making the final alignment on 2 in. by 8 in. by 40 ft parallel cord scissor trusses in preparation for plywood shee
at approximately 3:30 p.m. on april 7, 1993, employee #1 and a coworker were working on establishing the proper grade during
employees #1, #2, and #3, two backhoe operators and one surveyor, were locating underground utilities in preparation for a roa
employees #1, #2, and #3, two backhoe operators and one surveyor, were locating underground utilities in preparation for a roa
employee #1, a 67-year-old civil engineer, was walking up a flight of carpeted stairs to his office when he apparently fell. He wa
employee #1, a 30-year-old bricklayer, was completing repairs to a new building before its acceptance inspection. A coworker le
two power line workers were working from the bucket of an aerial lift, installing suspension insulators on new, grounded conduc
employee #1, a framing contractor, was installing osb roof decking with the help of two subcontractors. Employee #1 was walki
employee #1, a framing contractor, was installing rafters on the second level of a single family house under construction. While
employee #1, a roofer, was part of a two-man crew that was in the final stages of shingling an existing two-story home. He had
employee #1, a carpenter, was laying and framing walls on the second level of a single-family dwelling. He was working near an
temporary wiring had been installed on a job site, and non-metallic sheathed (romex) cable had been run to supply electric pow
employee #1, driving a mining industrial truck being used to transport aggregate up a dirt mountain road, had just dropped off th
employee #1 was working on a 8 ft stepladder while laying insulation across the top of acoustic ceiling titles. He lost his balance
a two-man crew had just completed a water break and was about to finish decking the first floor of a house. Employee #1, the o
employee #1 was working on a flat roof while cleaning tar off the top of a brick wall. He then climbed onto an apron which was l
employee #1, who was working in a trench, disconnected a sling between a piece of pipe and an excavator bucket. The excava
on the morning of august 14, 1995, employee #1 was framing a residential house. He was setting a truss over a foyer that cont
on april 12, 1996, employee #1 climbed a fixed ladder that was attached to the mast of a drill rig to retrieve the end of a broken
employee #1, an iron worker, was landing a bundle of corrugated metal decking when he fell approximately 25 feet. He suffered
on 11-4-96, at approx. 1:48 p.m., employees # 1-3, were on a connected set of four series s 50 quadrafloat barges, overall size
on 11-4-96, at approx. 1:48 p.m., employees # 1-3, were on a connected set of four series s 50 quadrafloat barges, overall size
on 11-4-96, at approx. 1:48 p.m., employees # 1-3, were on a connected set of four series s 50 quadrafloat barges, overall size
employee #1 was on the second floor of a school under construction when he tripped or stumbled into the fall protection system
employee #1 was on the second floor of a school under construction when he tripped or stumbled into the fall protection system
at approximately 4:00 p.m. on december 20, 1990, employee #1 was preparing to weld part of a steel conveyor that was 110 ft
on december 19, 1990, employee #1 was installing a thermoseparator 121 ft above ground level at methodist hospital in lubboc
employee #1 of a trenching contractor was buried while working in a trench approximately 9 feet deep, 2 feet wide, and 80 feet
employee #1 was using a handheld grinder on structural steel ends when he collapsed and died from congestive heart failure.
an employee raised a 480-volt overhead power line so that a tank could pass beneath the line. The power line was energized, a
employee #1 died as result of severe coronary atherosclerosis. He had undergone a triple coronary bypass in the past. The me
employees #1 and #2 were removing an 800 gallon, 8 ft by 20 ft tank that had contained new motor oil. The oil had been draine
employees #1 and #2 were removing an 800 gallon, 8 ft by 20 ft tank that had contained new motor oil. The oil had been draine
a five-person power line crew was assigned to install an overhead power line to energize oilfield equipment. A digger-derrick tru
at approximately 8:55 a.m. on march 8, 1993, employee #1 was working on a roof installing a roof membrane. He stumbled bac
at approximately 3:20 p.m. on august 3, 1993, employee #1 (the employer), and his two-man crew were finishing framing the se
an electrician supervisor for an electrical contractor was working on an overhead power line job. He walked around an aerial lift
an electrical contractor had assigned some employees that had been hired for the summer to remove some deenergized overh
an employee was driving a gin pole truck with its boom raised. The boom contacted a 22-kilovolt overhead power line, and the
employee #1 entered into a bin and 12 yards of sand was dumped on him, resulting in his suffocation. The company did not ha
employee #1, who had just been hired, and his foreman were walking up the rear of a roof. They were crossing over the ridge t
employee #1 was assisting his employer and the superintendent in off loading a 3,800 lb hot water storage tank from the bed o
employee #1, a member of a survey crew, was crossing the highway when he was struck and killed by a car.


                                                      Page 2
                                                         all


at approximately 2:00 p.m. on february 28, 1990, employee #1 was supervising the unloading of polyvinyl chloride pipe from a f
a crew of employees was installing a steel cable for a ladder safety device on a microwave tower. One of the crew members wa
employee #1 was shoveling dirt from a shallow trench left behind by a backhoe. The trench was being prepared for foundation
employee #1 had completed installation of a telephone cable and was driving a case maxi-sneaker, series b, model #m7069, e
an electrical crew was inspecting electric cables, transformers, and switchgear and was calibrating electric relays. A cabinet in
at approximately 10:05 a.m. on september 21, 1993, employees #1 and #3 were egressing a rooftop by way of a grove manlift
at approximately 10:05 a.m. on september 21, 1993, employees #1 and #3 were egressing a rooftop by way of a grove manlift
at approximately 10:05 a.m. on september 21, 1993, employees #1 and #3 were egressing a rooftop by way of a grove manlift
at approximately 1:15 p.m. on november 23, 1993, employee #1 was attempting to shut off the spray bar valve on the back of th
employee #1 was a flagman. A brown station wagon was entering the northbound lane to pass a vehicle heading south; it hit an
at approximately 10:45 a.m. on june 27, 1990, employee #1 was spotting for the dump truck drivers at a dirt work operation at a
at approximately 1:30 p.m. on october 3, 1990, employee #1 was supervising a crew that was leveling a site. The crew was ope
employees #1 and #2 were being hoisted by a base-mounted drum hoist (koenig winch, model hd 100b, king hoisting winch wit
employees #1 and #2 were being hoisted by a base-mounted drum hoist (koenig winch, model hd 100b, king hoisting winch wit
at approximately 9:30 a.m. on august 13, 1991, employee #1 and two coworkers were using a utility truck with a hoist to unload
employee #1 was part of a crew assembling a tower, boom, and merry-go-round for a 400 ton tower crane. The employee was
employee #1 was moving and reinstalling concrete forms inside a very confined space that was about 4 ft by 6 1/2 ft by 9 ft high
employees #1 and #2 were demolishing an old broken tower, which was constructed of 9 in. square tile and was 6 in. thick and
employees #1 and #2 were demolishing an old broken tower, which was constructed of 9 in. square tile and was 6 in. thick and
apparently the full bed of the dump truck that employee #1 had been driving was raised. When the bed did not dump, the emplo
employee #1, age 31, was assisting a welder in a 9 1/2 ft deep by approximately 4 ft wide excavation when the corner of the 45
employee #1 was walking across a roof from an access ladder to an area in which sandblasting was being done to remove old
employee #1 entered an approximately 30 ft deep completed sewer line at manhole #21. Employee #1 was apparently attempti
at approximately 3:00 p.m. on october 28, 1991, a construction crew of three, including employee #1, were repairing the boom
employee #1 had complained to his coworkers for approximately 2 weeks that he was experiencing chest pains and pains in his
a laborer took a break and laid down face-first on a concrete floor in front of a squirrel cage fan. He placed his hand on the pow
employee #1 and a coworker were elevated to 13 ft 6 in. on the rear of a scissor lift bed of a 2 ton truck. They were off-loading
employee #1 (the employer) was working with three employees on a 14 foot scaffold pick board installing sheetrock. No person
an employee on a power line crew was working on the ground. A coworker was operating an insulated aerial lift near an overhe
a power line worker was working from an aerial lift making electrical connections at a utility pole. He was working at a height of
employees #1 and #2 were working on a four-point suspended platform scaffold at the top of a 112 ft water tank. The work leve
employees #1 and #2 were working on a four-point suspended platform scaffold at the top of a 112 ft water tank. The work leve
at approximately 2:00 p.m. on january 28, 1993, employee #1 and coworkers were removing metal roofing from a structural ste
employee #1, who was on the ground, handed a sledge hammer to the superintendent inside the truck bed to drive a pin into pl
employee #1 had started his galion road grader and left it idling in gear to let the engine and transmission oils warm up. While t
an employee had installed several jumper cables between two junction boxes on a 277-volt lighting circuit so that he could repa
on march 23, 1990, employee #1 and five temporary labor employees, employed by phoenix roofing, inc. through tracy labor, a
two employees of a sign company were assigned to repair the lighting on a sign for a food store. The pole-mounted sign was lo
six employees were placing steel beams, weighing about 400 pounds each, into a crawl space under a floor in a school. Before
six employees were placing steel beams, weighing about 400 pounds each, into a crawl space under a floor in a school. Before
on or about march 11, 1991, employee #1 and several coworkers were placing roofing materials on the roof of a parking garage
on october 22, 1990, employee #1 and a helper were among a team of employees engaged in changing out about 4 miles of si
at approximately 7:30 a.m. on or about april 22, 1991, three employees were using a forklift to unload a tractor trailer of electric
at approximately 7:30 a.m. on or about april 22, 1991, three employees were using a forklift to unload a tractor trailer of electric
employee #1 and a coworker were assigned the task of removing an abandoned telephone pole. Employee #1 was directing th
a journeyman electrician was replacing ballasts in a 277-volt lighting circuit. The employee was working from an elevated positi
two employees, a night supervisor and a welder, were moving equipment to be used on a conveyor that transported concrete in
employee #1 and a coworker were taking apart the boom of a crane. Employee #1 crawled under the boom to remove the boom
at approximately 8:00 a.m. on november 13, 1992, employee #1, of benco, a coworker, and the company owner arrived at m&m
at 7:20 a.m. on january 10, 1995, employee #1 and four coworkers were engaged in replacing a section of the boom on a mani
employee #1 was washing down a concrete chute on a ready-mix truck when a nearby crane tipped over. The boom of the cran
employee #1 was on a flat roof 13 ft 5 in. above ground level, loading equipment and material onto a pallet on a case forklift, ck


                                                      Page 3
                                                        all


at approximately 10:50 a.m. on august 29, 1991, employee #1 was finishing pouring concrete on a bridge deck with a mobile cr
at approximately 10:50 a.m. on august 29, 1991, employee #1 was finishing pouring concrete on a bridge deck with a mobile cr
at approximately 10:50 a.m. on august 29, 1991, employee #1 was finishing pouring concrete on a bridge deck with a mobile cr
at approximately 10:50 a.m. on august 29, 1991, employee #1 was finishing pouring concrete on a bridge deck with a mobile cr
a 5-man work crew was performing a re-roof overlay of an existing townhouse building. Rain had delayed work at the building e
employee #1 was assisting in removing heads from the ends of heat exchanger tubes on oil refining equipment. The heads, wh
on april 21, 1992, employee #1 used an oxyacetylene torch to perform demolition work on a bridge which spanned a creek. He
on or about september 23, 1993, employee #1 and a grader operator were working on the construction of evaporation pond #1
a contractor was building and replacing overhead and underground power lines for an electric utility. One of the contractor's cre
at approximately 11:10 on march 23, 1993, employee #1 was walking back to his work area to prepare for an incoming load of
around 3:50 p.m. on wednesday, may 18, 1994, employees #1 and #2 were standing in the crevice of greenwade pit, an excava
around 3:50 p.m. on wednesday, may 18, 1994, employees #1 and #2 were standing in the crevice of greenwade pit, an excava
at approximately 3:00 p.m. on march 24, 1993, employee #1, the connector, and 2 coworkers were preparing to erect the final p
employee #1, assisted by employee #2, attempted to weld repair a tank containing diesel fuel. The tank exploded, drenching em
employee #1, assisted by employee #2, attempted to weld repair a tank containing diesel fuel. The tank exploded, drenching em
employee #1, assisted by employee #2, attempted to weld repair a tank containing diesel fuel. The tank exploded, drenching em
employee #1, assisted by employee #2, attempted to weld repair a tank containing diesel fuel. The tank exploded, drenching em
employee #1, assisted by employee #2, attempted to weld repair a tank containing diesel fuel. The tank exploded, drenching em
employee #1, assisted by employee #2, attempted to weld repair a tank containing diesel fuel. The tank exploded, drenching em
an employer and his employee were going to operate a pier drilling rig. The employee, who had been driving the rig, backed the
it was the end of the day and employee #1, a plumber's helper, was picking up welding leads and equipment. He was walking n
at approximately 12:30 p.m. on april 12, 1993, employee #1 and his coworkers were working at a lake at the rear of a residence
at approximately 9:45 a.m. on august 3, 1995, employee #1, of the foliage factory landscaping, inc., was riding in the bed of a p
at approximately 1:45 p.m. on january 29, 1996, employee #1 was working with a coworker on the roof of a building that was un
several employees were working on a barn facing and roof. Employee #1 was standing on a single board that had been placed
an electrician was working on a junction box, connecting wiring for an outdoor overhead lighting fixture. The employee was wor
employee #1 and two coworkers were bolting up lattice work on structural steel. Shortly after work resumed following lunch, em
an employee of a painting contractor finished working on one house (2502 brookline ct.) in a development. He asked the forem
employee #1 and two other laborers were excavating a trench in an attempt to locate a 4 in. natural gas main. Employee #1, the
employee #1 was one of two workers being elevated by a truck with two pulleys. When they were about 30 to 35 ft above the gr
a roofing crew set a hoist on a roof and used a water barrel as the base counter ballast. A motorized hoist was loaded and oper
employee #1 was in a 12 ft deep trench that measured 200 ft long, 2 ft wide at the bottom and about 5 ft wide at the top. He wa
employee #1 was riding on the fender of a truck. He fell to the pavement and was run over by the dolly wheels of the truck's tra
employee #1 was laying metal sheet roofing on a 16 ft 9 in. high building. He stepped back onto the edge of a metal piece of sh
employee #1, a dump truck driver, was crossing an active runway at the municipal airport in west helena, ar, when the dump tru
employee #1 and three coworkers were installing insulation and metal roofing on the top of a boiler building under construction.
two electricians were working on a switchboard in a vault. The employees were going to connect a new switch to an existing sw
at approximately 11:00 a.m. on july 10, 1996, employee #1 was on top of a flat roof at acxiom corporation, conway, ar, waterpro
a hydraulic pump operated the ramps of a lowboy operated by employee #1. The trailer was used to transport earthmoving equ
employee #1, 70 years old, was moving an fmc 96,000 pound link belt drag line into position to take it off a barge. The employe
an employer and three of his employees were using a boom truck to move a section of pipe from a pumping unit. While they we
an employer and three of his employees were using a boom truck to move a section of pipe from a pumping unit. While they we
an employer and three of his employees were using a boom truck to move a section of pipe from a pumping unit. While they we
employee #1, 27 years old, was removing his welding lead after finishing a welding job on the 85 ft level platform at producer's
employees #1 and #2 were laying pipe in the bottom of a 16 ft deep excavation when the west bank gave way. The falling exca
employees #1 and #2 were laying pipe in the bottom of a 16 ft deep excavation when the west bank gave way. The falling exca
an employee was changing a circuit breaker in 208-volt, three-phase panelboard. An electrical fault occurred, and the ensuing e
employee #1, age 16, was on the roof of a 27 ft by 8 ft metal building with his father when he stepped on a pile of insulation not
a crew of employees was troubleshooting a furnace. One of the employees, the owner of the company, entered a high voltage r
at about 11:10 a.m. on april 16, 1993, employee #1 and two coworkers were installing a two-point suspension scaffold on the ro
employees #1 through #6 were working in a private residence removing old carpet and adhesive by spraying lacquer thinner on
employees #1 through #6 were working in a private residence removing old carpet and adhesive by spraying lacquer thinner on


                                                     Page 4
                                                        all


employees #1 through #6 were working in a private residence removing old carpet and adhesive by spraying lacquer thinner on
employees #1 through #6 were working in a private residence removing old carpet and adhesive by spraying lacquer thinner on
employees #1 through #6 were working in a private residence removing old carpet and adhesive by spraying lacquer thinner on
employees #1 through #6 were working in a private residence removing old carpet and adhesive by spraying lacquer thinner on
employee #1, an assistant foreman, approached an area where a crane operator/foreman and a cutter had connected a 400 to
at approximately 10:10 a.m. on september 10, 1991, a call was received at the little rock, ar, area osha office noting the death o
employee #1 was one of two workers hooking a column to a beam at the top flanges. To do so, the crew was to crawl down a b
at approximately 2:30 p.m. on march 25, 1993, employee #1 was removing 3 ft by 6 ft deteriorated metal sheeting and installing
employee #1 was re-aligning two sets of press rolls. He was lying between the set that had been re-aligned earlier in the day an
employee #1 was inside a 47 ft long and 4 ft 6 in. wide reinforced steel cage. He was disconnecting a come-along that was bein
employee #1 was repairing an hydraulic seal in the lift bed of a dump truck when the left sleeve on the support axle at the rear e
employee #1 was a temporary temployee who had been on site for three weeks. He was on top of a 10 1/2 ft abs plastic manho
employee #1 and a coworker were adjusting a scaffold platform on a bent dock being constructed over a river. The platform wa
employee #1 was breaking a brick veneer wall away from the frame of a guardhouse. The steel structure and roof gave way an
employee #1 was removing a 1/4 in. rope from around the rubber bladder of a 5 ft diameter pipe plug that was in a vertical pipe
an employee entered a high-voltage vault in a steel manufacturing plant. It was not the employee's regularly assigned task to be
two brothers were working from a platform, installing an overhead door. The platform was supported by the forks of a turbo lift f
employee #1 was working on a communication tower approximately 140 ft above ground when he fell to the ground. He died in
at approximately 12:30 p.m. on april 20, 1991, employee #1 was getting onto the platform of a two-point suspension scaffold th
employee #1 walked across a 3 in. gypsum insulation board that had been cut through to install a skylight. He fell approximately
an employee was electrocuted while he was servicing industrial wet cell storage batteries used in an uninterruptible power supp
on october 12, 1994, employee #1 and another employee were preparing to load shingles on the second story roof of a building
employee #1 was working on a waterborne dredge, a specialized piece of equipment used to harvest the weeds in a lake. He d
on october 21, 1996 at approximately 11:24 am, employee #1 was preparing to paint the soffits around the entire house that wa
an elevator mechanic was working on electrical boxes on the top of a dover hydraulic passenger elevator. The elevator was no
employee #1 was working above an excavation, either walking toward the backhoe bucket or standing at the edge, waiting for t
on november 10, 1994, employee #1 was climbing a ladder with roof shingles in his arm. As he was going up the ladder, he fell
employee #1 was operating a horizontal boring machine inside a trench excavation that measured 16 feet deep, 10 1/2 feet wid
at approximately 10:30 a.m. on november 21, 1990, employee #1 and a coworker were sent by their employer to pick up vinyl s
on may 22, 1991, employees #1, #2, and #3 were installing pvc pipe in a sewer system. Employees #2 and #3 were picking up
on may 22, 1991, employees #1, #2, and #3 were installing pvc pipe in a sewer system. Employees #2 and #3 were picking up
on may 22, 1991, employees #1, #2, and #3 were installing pvc pipe in a sewer system. Employees #2 and #3 were picking up
employee #1 was working on the third floor level in front of an elevator shaft opening. Judging by the masonry debris found on t
at approximately 7:40 a.m. on november 24, 1993, employees #1 and #2 got on a two-point suspension scaffold from the roof o
at approximately 7:40 a.m. on november 24, 1993, employees #1 and #2 got on a two-point suspension scaffold from the roof o
on august 11, 1993, employee #1, an unacclimated but healthy 21-year old carpenter's apprentice, was on his seventh day of e
employee #1 was loosening and removing parapet stones on a flat roof building, 44 ft 6 in. above the ground. One stone had ju
at approximately 12:30 p.m. on july 12, 1994, employee #1, a laborer for a masonry company, was on his first day laying brick a
on september 4, employee #1 came to a construction site to do general clean-up. The work was originally scheduled to be done
an employee was working from a 12.2-meter (40-foot) aluminum ladder, installing a 4.6-meter-long (15-foot-long) section of gut
at approximately 2:00 p.m. on may 29, 1990, employees #1 through #5 were part of an oil well workover crew that was preparin
at approximately 2:00 p.m. on may 29, 1990, employees #1 through #5 were part of an oil well workover crew that was preparin
at approximately 2:00 p.m. on may 29, 1990, employees #1 through #5 were part of an oil well workover crew that was preparin
at approximately 2:00 p.m. on may 29, 1990, employees #1 through #5 were part of an oil well workover crew that was preparin
at approximately 2:00 p.m. on may 29, 1990, employees #1 through #5 were part of an oil well workover crew that was preparin
at approximately 9:30 a.m. on july 18, 1990, employees #1, #2, and #3 were vertically installing large concrete pipe for a sewer
at approximately 9:30 a.m. on july 18, 1990, employees #1, #2, and #3 were vertically installing large concrete pipe for a sewer
at approximately 9:30 a.m. on july 18, 1990, employees #1, #2, and #3 were vertically installing large concrete pipe for a sewer
employee #1 was painting the inside of a water tank. He was sitting in a genie chair that was being held up by two sets of 5/8 in
employee #1 was stretching wire to connect to a pump next to a sewage lagoon when he stepped onto the plastic liner that exte
employee #1 connected a high-pressure oxygen bottle to welding equipment without installing a regulator to control the oxygen
employee #1 was riding a swinging scaffold down the side of a water tank when the air line for a sand blaster became caught b


                                                      Page 5
                                                           all


an employee was measuring the height of a city water tank with a metal tape. He was standing on a metal catwalk about 100 fe
on july 17, 1992, employee #1 was a member of an eight-person crew consisting of six equipment operators and two superviso
at 3:30 p.m. on august 13, 1992, employee #1 picked up an unsecured 4 ft by 8 ft sheet of 1/2 in. plywood that was covering tw
employee #1 and a coworker were members of an eight-person crew working on the roof of an addition to a manufacturing plan
employee #1, a drywall installer, was nailing down the bottom of a piece of drywall while sitting astraddle a 2 by 12 in. scaffold b
a tool trailer on a jobsite was sitting in a large pool of water. The jack stand supporting the trailer was also sitting in the water. T
at approximately 8:00 a.m. on december 31, 1993, employee #1 was securing stay-in-place metal deck concrete forms betwee
an employee was working under a house in a 2.5-foot crawl space. He was installing a section of trunk line ductwork. He conta
employee #1 was standing on the guarded catwalk platform of a water tower that was under construction. While on the catwalk
employee #1 was compacting fill for roadway construction with a vibratory compactor. He moved the compactor into the roadwa
at approximately 1:45 p.m. on november 14, 1994, employee #1 and a coworker were cleaning the exterior walls of a housing u
employee #1 was moving a 4,000 lb capacity caterpillar forklift, type 6, model v40b, from one dock to another at the tva haitsvill
at approximately 10:00 a.m. on october 14, 1991, employee #1 and two coworkers were installing sections of a safety rail to a la
at approximately 9:20 a.m. on september 20, 1990, employee #1 and a coworker were working adjacent to the area where two
employee #2 entered an underground pit through a manhole at the termination of a water utility conduit system. The system wa
employee #2 entered an underground pit through a manhole at the termination of a water utility conduit system. The system wa
employee #2 entered an underground pit through a manhole at the termination of a water utility conduit system. The system wa
employee #2 entered an underground pit through a manhole at the termination of a water utility conduit system. The system wa
employee #2 entered an underground pit through a manhole at the termination of a water utility conduit system. The system wa
employee #2 entered an underground pit through a manhole at the termination of a water utility conduit system. The system wa
employee #2 entered an underground pit through a manhole at the termination of a water utility conduit system. The system wa
employee #1 and a coworker were setting up a scaffold between two balconies. One of the boards placed between the open-si
employee #1 was inside a hopper on an aran mobile roadbase stabilization plant. Employee #1 was removing dirt from the side
at approximately 3:30 p.m. on may 3, 1991, employee #1 was performing survey work, shooting a grade across a four lane divi
at approximately 9:30 a.m. on may 23, 1991, employee #1 was cleaning the unguarded deck of a barge. The employer was con
at approximately 2:50 p.m. on august 17, 1995, employee #1 was traveling west on a winding dirt roadway in an empty caterpill
at approximately 6:00 p.m. on september 6, 1995, employee #1 and two coworkers were riding on the back of a tractor trailer, s
on october 27, 1995, employee #1 was on the north side and near the top of a vertical form. He was trying to connect a work pl
two electricians were installing wiring to supply temporary lights and power in a vacant grocery store. The employees were pulli
at approximately 10:17 a.m. on july 26, 1990, employee #1 was standing in a trench observing a sewer line pipe that was being
employee #1 was operating a case w30 front end loader, which weighs approximately 27,000 lb. The employee dumped a load
at 2:20 p.m. on september 19, 1990, five employees were doing stucco work from a motorized work platform. A beam pitched d
a painter was relocating a 28-foot-long aluminum extension ladder. The ladder contacted an overhead power line, and the pain
employee #1, the owner, was helping his employees raise a floor beam. The beam displaced, then fell and struck employee #1
an employee of a communications contractor was attached to a communications cable being hoisted up a television tower. The
the guardrail in front of an elevator shaft had been removed while material was being loaded and no one was guarding the open
employee #1 was helping the driver of an 18-wheeled tractor trailer unload cast-iron pipes for a water line project. The employe
at approximately 2:00 p.m. on march 25, 1991, employee #1 was sandblasting inside a 122 ft high water tank when the cable h
an employee working for a general contractor was on an aluminum ladder, painting over an existing sign on the side of a buildin
employee #1 was standing against the steel shoring of a coffer dam. A hitachi backhoe was being used to remove mud and wa
at approximately 3:15 p.m. on august 6, 1991, employee #1 was working at a highway bridge construction site at the end of his
on october 8, 1991, employee #1 was working as a landscaper for ferguson landscaping at a construction site in acworth, ga. H
a truckload of steel rebar was being unloaded at a construction site at the town center mall. The bundles of steel were being pla
a truckload of steel rebar was being unloaded at a construction site at the town center mall. The bundles of steel were being pla
employee #1 had completed troweling stucco on a building's exterior wall. He went to the end of the scaffold, which was one sta
an employee was moving a 40-foot aluminum ladder around the side of an apartment building. The ladder contacted an overhe
employee #1 was installing an 8 inch pvc sewerline pipe in an unshored trench that was 12 to 14 feet deep. A wall caved in on t
sometime before 5:00 p.m. on february 28, 1992, employee #1 was using a caulking material to seal the second floor windows
at approximately 10:00 a.m. on november 16, 1992, employee #1 was nailing a 4 by 8 section of particle board to the roof of a r
employee #1 and his son were repairing/replacing the hydraulic cylinders on a 950 caterpillar front end loader. The employee's
at 9:00 a.m. on march 23, 1995, employee #1 was operating a scissor lift to the catwalk area of a theater. Employee #2 was ins
at approximately 11:30 a.m. on april 16, 1992, employee #1 entered a 15 ft 9 in. deep manhole that was part of a new sewer lin


                                                        Page 6
                                                         all


at approximately 11:30 a.m. on april 16, 1992, employee #1 entered a 15 ft 9 in. deep manhole that was part of a new sewer lin
at approximately 2:15 p.m. on april 17, 1991, employees #1 and #2 were in a 12 ft deep straight wall excavation without shoring
at approximately 2:15 p.m. on april 17, 1991, employees #1 and #2 were in a 12 ft deep straight wall excavation without shoring
employee #1 had unhooked his lanyard from his anchorage prior to climbing a 20 ft long column. He was trying to get a pin to r
employee #1 was removing reflective marking from a highway with a shovel when a dump truck struck him, throwing him appro
employee #1 was cutting and attaching plywood sheeting to a two story house under construction. He fell to his death from the
at approximately 5:30 a.m. on july 18, 1996, employee #1 was operating a water truck from inside the cab. Parallel to the water
employee #1 was alone on the roof of a five-story condominium restarting air-conditioning units. The units had been disconnect
at approximately 4:00 p.m. on april 10, 1997, employee #1 was erecting a communications tower with a coworker. At the 160 ft
a three-person power line crew was setting a 45-foot-tall pressure-treated utility pole under a 230-kilovolt overhead power line.
a three-person power line crew was setting a 45-foot-tall pressure-treated utility pole under a 230-kilovolt overhead power line.
a three-person crew was installing an automatic transfer switch for an emergency generator system. Power for the switch came
a employee was operating a diamond rac tandem crane to move a concrete septic tank weighing about 5500 pounds from the f
employee #1 had been smoothing a private dirt road, using a 1978 john deere tractor, jd-401-b #290599t, that was dragging so
employee #1 lost control of his front end loader, jumped off, and was run over by a rear wheel. He was killed.
employee #1, a construction worker, was applying sealer compound to a hardwood floor in a small hall area. Another worker wa
at approximately 12:55 p.m. on september 26, 1991, employee #1 was performing construction work in an operating oil filtration
employee #1 was under the bed of a dump truck, between the truck frame and the dump bed, removing a hydraulic hose from
employee #1 jumped into a trench to install a board over a sewer line that he hand located in the trench. The trench was 23 ft in
employee #1 was removing a 10-ton scraper blade from a lowboy trailer. He went to adjust the chain used to pull the blade from
a power line worker was working from an aerial lift, connecting a 7200-volt overhead power line to a switch mounted beneath a
an employee was standing on a wooden stepladder, wiring an emergency fluorescent lighting fixture at a new school under con
an employee was laying unpainted, corrugated sheet metal on the roof of a building under construction. The screw gun the emp
employee #1 was helping to remove the tailgate of an over-the-road c60 chevrolet flat body truck to dump a load of fill dirt at a r
employees were dismantling a 190 ft am radio tower. The tower had been dismantled down to the last 30 ft and the last set of p
employees #1 and #2 were working in a highway resurfacing area that was 2 lanes in each direction with a median. The westbo
employees #1 and #2 were working in a highway resurfacing area that was 2 lanes in each direction with a median. The westbo
employee #1, a truck driver, was attempting to turn into a dirt driveway with a lowboy trailer loaded with two dozers. The drivewa
at about 10:00 a.m., the employer and employee #1, a carpenter's helper, arrived at the worksite of a home being remodeled. T
two employees were replacing rotten and damaged utility poles. To do this, the employees dug a new hole next to the existing p
a company had completed asphalt road resurfacing and was applying gravel to the highway's shoulder to even the surface. The
a painter and his coworker were erecting a ladder jack scaffold. The painter was standing on a metal pickboard at a height of 2
employees were laying felt atop a 20 ft 6 in. high, 12:12 pitched roof. Employee #1 was standing against a 2 by 4 toe board of b
employee #1 and a coworker were riding on an asphalt paving machine. The operator lost control of the machine and struck a p
a backhoe had lifted a 21-foot-long steel pipe into a standing position. One end of the pipe was just inside a steel collar. As two
a backhoe had lifted a 21-foot-long steel pipe into a standing position. One end of the pipe was just inside a steel collar. As two
a crew was erecting structural steel. Several 32 ft tall columns had been erected and bolted down to the footing with two ancho
a crew was erecting structural steel. Several 32 ft tall columns had been erected and bolted down to the footing with two ancho
two employees were raising a 32-foot-long aluminum ladder for access to the roof of a building. The ladder contacted a nearby
two employees were raising a 32-foot-long aluminum ladder for access to the roof of a building. The ladder contacted a nearby
employee #1 and coworkers were sandblasting and painting a water storage tower/tank. Employee #1 was lowering an approxi
employee #1 was struck by the rear of a rotating link-belt excavator. He fell 9 ft into a creek channel where he struck his head o
some i-beams had been piled under a 161-kilovolt overhead power line. The owner of a contracting firm and two of its employe
at approximately 11:50 p.m. on april 25, 1993, employee #1 and two coworkers were hanging drywall from a scaffold platform t
at approximately 1:55 p.m. on june 1, 1993, employee #1 was removing soil from a sewer tap in a trench that was 20 feet long
on or about may 11, 1992, employee #1 was working on the roof of a building. He stepped onto an area of the roof that was cov
two employees were installing propane piping in the attic of a residence. One of them contacted exposed live parts on an attic v
an employee was painting a metal sign at a gasoline station. The sign was about 2 feet from an overhead power line. The empl
at approximately 9:00 a.m. on july 20, 1993, employee #1 and five coworkers were making asphalt repairs on a two-lane road a
employee #1 was moving a hydraulic crane down a hill when he had a heart attack, which caused him to swerve off the road. T
the employer tore away a portion of a two story building to expose a steel support beam. The unsupported brick veneer wall col
employees #1 and #2 were attempting to disassemble a crane lattice boom. The boom was lowered approximately 7 to 8 ft abo


                                                      Page 7
                                                         all


employees #1 and #2 were attempting to disassemble a crane lattice boom. The boom was lowered approximately 7 to 8 ft abo
employee #1 was on a roof performing built-up roofing. Two other employees were rolling out a sheet of single ply, modified bit
at approximately 3:30 p.m. on may 22, 1990, employee #1 was preparing to remove a jack from under a 48 in. water pipe while
at approximately 4:30 p.m. on april 2, 1993, employee #1 was nailing rafters in place on a garage. He was standing on the lowe
at approximately 7:45 a.m. on april 26, 1990, employee #1 was working in an excavation for a bridge abutment. He was using a
at approximately 11:30 a.m. on july 10, 1990, employee #1 was working approximately 15 ft above the ground from a metal bea
two employees were installing three current transformers in an energized three-phase, 480-volt, 800-ampere panelboard. Each
two employees were installing three current transformers in an energized three-phase, 480-volt, 800-ampere panelboard. Each
at approximately 2:30 p.m. on june 24, 1993, the president of the company found employee #1 lying underneath a 48 in. bush h
employee #1 had just finished welding a 16 ft by 5 ft diameter pipe and was getting off a boatswains chair and onto a fixed stee
employee #1 went on the roof to help his father and two other men change an air condition compressor. For some reason, he f
at approximately 10:50 a.m. on august 23, 1992, a section of ground floor brick wall had been pulled to the ground with a backh
employee #1 was preparing to leave work as it was quitting time. His supervisor called to him that it was time to go. He walked
employee #1 fell 35 ft through an unguarded hole in a bridge to the water and drowned.
at approximately 7:55 a.m. on june 25, 1993, employee #1 was directing a road grader on how much grade to cut. After the roa
employee #1, who was working from a single-point suspension scaffold, was inadvertently cut from his suspension point by a c
at approximately 10:15 a.m. on june 23, 1990, a work crew cut a trench through an earthen driveway abutment, thereby increas
employee entered an unsbored trench 13 feet in depth to place soap grease on a pipe bell. Thewist wall caved in covering the e
employee #1 was found lying face down on a floor near a manlift in a puddle of blood. According to the medical examiner's offic
employees were erecting/installing a automated storage/retrieval system consisting of 2-3'9 1/8"x119' metal racks, 31'10" in he
employee #1 was backing a forklift onto a lowboy trailer to transport it to a job site on i-20 at boulevard ave. On the first attempt
employee #1 was run over by a dump truck while the truck was backing up to unload asphalt for road work. The employee was
employee #1, the company owner, was loading a bobcat onto a lowboy trailer. When he stood up inside the cage of the bobcat
on the morning of february 27, 1990, employee #1 acquired the independent service key for elevator #1 from building managem
on february 20, 1990 at approximately 12:30 pm employee no's 1&5 along with coworker went to roof and over a power boiler in
on february 20, 1990 at approximately 12:30 pm employee no's 1&5 along with coworker went to roof and over a power boiler in
a three-person crew was working in a 2-foot, 4-inch-deep excavation. The were setting up a boring rig to install a 20-inch-diame
a crew foreman, who had worked for his employer for 10 years, was installing a new cable television cable. He was wearing on
employee #1 climbed over a 42 inch guardrail and entered a ventilation shaft to retrieve some blueprints that had fallen in. He f
employee #1 was a member of a four-man crew that was sawing and sealing joints on an interstate highway. As the crew drove
at approximately 11:00 a.m., on august 30, 1994, employee #1 was setting bolts in a steel structure from a 6 ft stepladder when
employee #1 fell 27 ft through a skylight opening. He sustained multiple fractures and was killed.
two employees were unloading 12-meter-long, 25-millimeter-diameter steel pipe. The load line of the lorain crane being used to
two employees were unloading 12-meter-long, 25-millimeter-diameter steel pipe. The load line of the lorain crane being used to
employee #1, who had been assigned to paint a ceiling, was discovered lying at the foot of a 38 ft high scissor lift. He died at th
employee #1 was trimming debris and limbs from fallen pine trees while a trackhoe operator pulled the trees down to prevent th
on may 27, 1993, employee #1 was building up scaffold sections. He was replacing 8 ft walkboards with 16 ft walkboards when
an electrical contractor and one of his employees were installing transformers and wiring for a switchboard. They had installed
a power line worker removed his gloves while he was working on a power line. He contacted the 7200-volt line and was electro
employee #1 was working on one section of a tubular welded-frame scaffold about 6 feet 10 inches above ground level. When
an employee working on top of a tank was installing a gauge and float system. He was using a coil of wire rope in the installatio
employee #1 and four coworkers--one of whom was the foreman--were laying bridge forms/pans on the deck of a bridge under
at approximately 3:00 p.m. on october 11, 1994, employee #1 had finished connecting a 60 ft truss when he fell approximately
employee #1 was sitting on an i-beam that he was preparing to remove from structural steel framework located inside a co-gen
employee #1 was sitting on an i-beam that he was preparing to remove from structural steel framework located inside a co-gen
employee #1 and a coworker were installing 6 in. Pvc sewer pipe in an unshored trench that was 2 ft wide and approximately 8
Employee began removing old electrical service to replace with a new one, using a metal utility knife to cut through some insula
on june 3, 1994, employees #1 and #2 were installing a 24 in. diameter clay pipe inside a trench measuring 33 ft long by 6 ft wid
on june 3, 1994, employees #1 and #2 were installing a 24 in. diameter clay pipe inside a trench measuring 33 ft long by 6 ft wid
on june 16, 1994, employee #1 was working from atop the crosshead of a traction elevator car-sling which was suspended from
employee #1 was working on the second floor deck of a new single family home, cutting pieces of exterior sheeting (30 inch by
employee #1 was either loading or unloading rocks from the front of a backhoe when he was struck and killed by the backhoe's


                                                       Page 8
                                                         all


employee #1, a flagperson, was struck and killed by an oncoming vehicle.
a dump truck that was backing up struck and ran over employee #1. He died from his injuries.
at approximately 11:30 a.m. on february 20, 1993, employee #1 was descending a stepladder that was positioned to straddle th
an employee was operating a ditch witch to excavate for an underground power line installation. The machine struck a 4160-vo
at approximately 9:20 a.m. on april 7, 1994, employee #1 fell 20 ft from a ladder to the concrete floor. He died.
at approximately 11:56 a.m. on august 10, 1994, employee #1 was cutting into the end of an empty 6,000-gallon gasoline tank
an employee was working on a 277-volt lighting circuit. He thought it was deenergized, but it was not. He was electrocuted.
an employee was in an elevated position on a scaffold, installing vinyl siding on a residential structure. The employee touched a
several employees were installing a 30 in. steel water line in a trench approximately 75 ft long by 14 ft wide by 9 ft deep. To pro
employee #1 and a coworker had applied a masonry finish to the outside wall of a residence and were dismantling the scaffold.
employees #1 & #2 and a crane operator had the task of installing an aluminum lighting pole with attached arm on to an existin
employees #1 & #2 and a crane operator had the task of installing an aluminum lighting pole with attached arm on to an existin
employee #1 squeezed between the guardrails protecting an approximately 1/8 in. thick plywood floor hole cover and stood on
the foundation wall of a building being added on to had been recently exposed and left unsupported. As employee #1 walked by
on may 20, employee #1 and a coworker went to clean windows in an apartment on the 12th floor of a building. They rigged a b
employee #1 was in the basement motor of building a taking measurements near the shaft of elevator a-1. He was standing on
employees #1, #2, and #3 were on the roof of a warehouse and employees #4 through #9 were on the ground when an adjoinin
employees #1, #2, and #3 were on the roof of a warehouse and employees #4 through #9 were on the ground when an adjoinin
employees #1, #2, and #3 were on the roof of a warehouse and employees #4 through #9 were on the ground when an adjoinin
a 50 lb fiberglass container measuring 17 1/2 in. by 28 in. by 39 in. was being hoisted to the roof of a 5 story building to remove
at approximately 7:30 a.m. on september 9, 1991, employee #1 was on an elevated highway comprising approximately 4,000 fe
employee #1 was removing a window lintel when the unlashed scaffold swayed away from the building. He lost his balance and
on september 9, 1991, employees #1, #2, #3, and #4, of clared construction co., were preparing to leave for the day after pointi
on september 9, 1991, employees #1, #2, #3, and #4, of clared construction co., were preparing to leave for the day after pointi
on september 9, 1991, employees #1, #2, #3, and #4, of clared construction co., were preparing to leave for the day after pointi
on september 9, 1991, employees #1, #2, #3, and #4, of clared construction co., were preparing to leave for the day after pointi
employee #1, a 26-year-old, was cutting apart a stainless steel tank that measured 15 ft in diameter and 35 ft long. The tank wa
at approximately 7:15 a.m. (15 minutes after the start of the work day) on january 2, 1992, employee #1 and a coworker, both fo
employee #1 and a coworker were painting the entire interior and exterior windows of a 4-story brick roman catholic school. The
employees #1 and #2 were part of a six-man wrecking crew performing interior demolition in a five-story residential building und
employees #1 and #2 were part of a six-man wrecking crew performing interior demolition in a five-story residential building und
on may 1, 1991, employees #1 and #2 were standing at the first floor level on a temporary platform that spanned the elevator s
on may 1, 1991, employees #1 and #2 were standing at the first floor level on a temporary platform that spanned the elevator s
on may 1, 1991, employees #1 and #2 were standing at the first floor level on a temporary platform that spanned the elevator s
at approximately 2:15 p.m. on july 27, 1990, employee #1, a laborer, was in a trench, approximately 6 1/2 ft deep by 7 ft wide by
employee #1 was crushed to death by a bucket of stone that fell from a crane hook.
employee fell from 5th. floor level of a tubular welded frame scaffold (between the building wall and scaffold) to the first floor ca
an asbestos abatement worker was electrocuted when he cut a 277-volt metal-clad cable with a pair of bolt cutters. (The remai
at approximately 8:35 a.m. on october 11, 1990, employee #1, a general contractor, was walking on a runway above a church c
at approximately 10:30 a.m. on november 17, 1990, the employer was setting up steam cleaning equipment to be used to clean
a carpenter and his helper were working from a 6-foot-tall metal scaffold, hanging sheetrock. A 120-volt, non-metallic sheathed
employee #1, an iron worker, was installing overhead protection in an elevator shaft at the eleventh floor of a building under con
at approximately 1:00 a.m. on september 26, 1991, employee #1, a laborer and mechanic, fell approximately 26 1/2 feet to his
at approximately 4:00 p.m. on december 27, 1990, employee #1 was trying to pull a concrete hose closer along a form when he
at approximately 4:00 p.m. on december 27, 1990, employee #1 was trying to pull a concrete hose closer along a form when he
employee #1, an iron worker, was cutting out a temporary steel brace when the last 1 1/2 in. of the steel that was holding the st
employee #1 was cutting a concrete slab from a deteriorating pier when he accidentally cut the slab out from under him. He fell
an overload relay tripped, causing an elevator to stop between the sixth and seventh floors. Employee #1 attempted to escape
employee #1 was removing asbestos from a containment area. He was wearing a papr. He suffered an apparent heart attack a
a building damaged by fire and water had no bracing or shoring. Employees #1 and #2 were removing debris from the floor and
a building damaged by fire and water had no bracing or shoring. Employees #1 and #2 were removing debris from the floor and
at approximately 12:30 p.m. on july 17, 1992, employee #1, the bell ringer for a material hoist on the 12th floor of a building on m


                                                       Page 9
                                                        all


in the basement burner room on the north side of the building, employees were bleeding air from gas lines over and around a tw
at approximately 3:30 p.m., employee #1 was standing on a 5 ft ladder on a balcony on the 6th floor of an apartment building in
employee #1 was about to use a reimann georger hydraulic swing hoist, model 00448, serial #68850. He loaded the hoist buck
at approximately 1:10 p.m. on october 1, 1992, employee #1 was working at the roof level (approximately six floors up) on a co
an elevator mechanic was troubleshooting a problem in an elevator control panel located in an elevator control room. The pane
two employees of an electrical contractor were installing a coaxial cable for a surveillance camera. The two employees were on
an employee was pressure washing the under-structure of a bridge to prepare it for painting. Working from a suspended work p
a 33-year-old employee was instructed by his supervisor (the owner of the contracting firm) to clean up construction debris in th
employee #1, an iron worker on a highway viaduct rehabilitation project, was replacing rivets in a roadway support beam when
employee #1 was on a 2 in. o.d. pipe structure built as a support system for a canvas, outside vertical scaffold cover. The pipe
at approximately 7:30 a.m. on june 9, 1993, employee #1, a journeyman electrician with 15 years of experience, had been assig
at 5:31 a.m. it was still dark. A bobcat operator and two coworkers had finished loading a bobcat onto a flatbed truck to transpo
an employee was replacing a broken pipe in an excavation. The excavation was 4 feet by 4 feet and was 4.5 feet deep. He was
employee #1 was restoring a building's exterior. He was stepping down from the 13th floor onto a 2-point suspended scaffold w
at approximately 10:40 a.m. on monday, january 24, 1994, eight workers were removing debris from a dilapidated 4-story brick-
at approximately 10:40 a.m. on monday, january 24, 1994, eight workers were removing debris from a dilapidated 4-story brick-
at approximately 10:40 a.m. on monday, january 24, 1994, eight workers were removing debris from a dilapidated 4-story brick-
at approximately 10:40 a.m. on monday, january 24, 1994, eight workers were removing debris from a dilapidated 4-story brick-
employee #1, who was supervising the repair of a parapet entered a two-point suspension scaffold at roof level and was walkin
employee #1 was doing masonry work on the 4th floor (top floor) of a gut rehab job. He was working on a small, site-made wor
a carpenter was performing electrical work. He contacted an exposed circuit part energized at 277 volts and was electrocuted.
a carpenter was performing electrical work. He contacted an exposed circuit part energized at 277 volts and was electrocuted.
on july 26, 1994, employee #1, a pipe fitter, was installing air conditioning piping while standing on a stepladder. The employee
at approximately 2:20 a.m. on october 24, 1994, employee #1, a laborer for tpk construction company, was walking uphill towar
at approximately 10:30 a.m. on december 3, 1994, employee #1, the proprietor of the company, with the assistance of the site b
at approximately 11:25 on december 13, 1994, employee #1 was engaged in the demolition of a steam boiler. He was working
at 1:43 p.m. on december 20, 1994, employee #1, a carpenter who worked for julius a. nasso & associates concrete corp., was
employee #1, a roofer, while installing roof edge flashing, suffered a heart attack and fell 11 feet 3 inches to a concrete ramp. H
employees #1, #2, and #3 were atop a tubular frame scaffold that had been erected adjacent to the side wall of a five-story mas
employees #1, #2, and #3 were atop a tubular frame scaffold that had been erected adjacent to the side wall of a five-story mas
employees #1, #2, and #3 were atop a tubular frame scaffold that had been erected adjacent to the side wall of a five-story mas
an employee was disconnecting a 277-volt lighting fixture mounted in a ceiling. The lighting circuit was not deenergized, and the
employee #1 was attempting to open a 14 ft by 14 ft steel door securing a storage area from theft and vandalism during constru
csho arrived on jobsite 5-16-90 at app 10:45am credentials were presented to richard farwell owner of richard farwell & sons g
employee #1, an iron worker, was working and walking on a structural steel beam. He fell 27 ft 5 in. from the steel beam to the
on july 9, 1993, employee #1 was spreading metal decking on the roof of a boathouse under construction. He was straddling th
the owner of a construction company was lowering an aluminum pole for a pump jack scaffold. He contacted an 8000-volt over
employee #1 fell from the roof level of a gymnasium to the gym floor while removing the roof. Employee #1 was taking a smokin
employee #1 was working in an unshored trench. When the trench collapsed he was seriously injured and died.
employee #1 was removing a tarp covering a roof in freezing rain. He was killed when he slipped and fell 36 ft to the ground.
a 36-year-old employee received an electric shock. He collapsed 50 minutes later and died. The medical examiner ruled that th
during a roofing operation, employees were installing built-up roofing materials while adjacent to a large opening. Employee #1
employee #1 was installing electrical equipment for parking lot lights. He was working within an enclosure for an air handling un
employee #1 was attempting to climb down the exterior of a tubular welded scaffold when he slipped and fell to ground level. H
on october 22, 1993, employee #1, vice president and subcontractor supervisor/employee of inland builders inc., was on a balc
employee #1 was driving a john deere 650g crawler dozer onto a trailer that was on unlevel ground. The dozer slipped off the tr
employee #1 was killed when he fell from a ladder while removing an outside awning.
an employee was painting under the switchgear for an elevator that was in operation. The employee contacted a 240-volt circui
employee #1, of eagle site developers, was clearing a chute opening on a rock crusher machine while the machine was in oper
employee #1 fell from a roof edge while brooming roofing paper. He was killed.
employee #1, age 71, was on a roof installing new roofing material when he fell approximately 9 ft to the ground. He was killed.
at approximately 1:00 p.m. on december 13, 1993, employee #1 was standing on top of a tanker truck during an air purging ope


                                                     Page 10
                                                           all


employee #1, 17 years old, was working in an unprotected 12 ft deep trench when the side wall collapsed. His head was fractur
employees #1 and #2 were setting a 5 ton concrete end cap into place. The end cap was being lowered by a crane and the em
employees #1 and #2 were setting a 5 ton concrete end cap into place. The end cap was being lowered by a crane and the em
while walking across a support beam and wearing a harness not attached overhead he fell 17 feet onto a concrete floor.
as employees #1 and #2 lowered themselves on a two-point suspended scaffold, one of the supporting cables parted and the e
as employees #1 and #2 lowered themselves on a two-point suspended scaffold, one of the supporting cables parted and the e
employee #1 fell from a scaffold or roof while working on the chimney. He landed on pressure treated porch joists that were abo
employee 1 was working on a communications tower replacing the existing braces with stronger braces in preparation for the in
a multi employer work site; 2 separate subs for a town water main project. A sub for a blasting and trenching for the other. One
three workers were using a drilling rig to install posts for a guardrail system at the side of the road. The mast of the rig contacte
three workers were using a drilling rig to install posts for a guardrail system at the side of the road. The mast of the rig contacte
three workers were using a drilling rig to install posts for a guardrail system at the side of the road. The mast of the rig contacte
employee was a groundsman for a road milling machine. The road milling machine had backed up to start another cut in the ro
roof bracket failed and individual fell about 24 feet to ground from the cable side of the roof. It was assumed that the individual
employee #1 was mopping asphalt when he backed off the edge of a flat roof. He died. The company did not comply with 1926
employee #1 was working with a crew on a trenching operation where pvc sewer pipe and new precast concrete manholes wer
two employees were painting a house. The ground was snow covered and wet, and the weather was cold. A 40-foot aluminum
two employees were painting a house. The ground was snow covered and wet, and the weather was cold. A 40-foot aluminum
two electricians had just started working inside a piece of high voltage equipment. The electricians had not deenergized the 416
two electricians had just started working inside a piece of high voltage equipment. The electricians had not deenergized the 416
at approximately 8:30 p.m. on october 16, 1996, employee #1 was removing a 20 foot by 40 foot tarp containment curtain that w
employee working on installing wood frame wall at ground level working on the inside area was crushed by an unattended truck
employee was coming out from a sludge concrete tank through a 3'x3' floor opening using a 16ft. Single cleat job made ladder.
a portable electric generator was being used in the construction of a house. Exposed conductors had been inserted into the 240
employee #1 and a coworker were working on a ladder jack scaffold approximately 8 ft tall when an employee of another comp
employee #1 was working on an unguarded scaffold approximately 15 ft above the ground, clearing snow off a roof. He slipped
a sole-proprietor electrical contractor was installing new wiring to connect a new machine. As he was connecting a conductor, h
workers were installing a pre-constructed home unit on a site. After the hinged roof unit was lifted into contact placement, empl
employee #1, who was estimating the removal of an outside overhead crane, climbed up on the crane's 32 ft fixed ladder to ins
on august 14, 1990, employee #1 and three coworkers were removing asphalt shingles from the roof of a single story residence
on march 5, 1990, employee #1 and a coworker were starting to move furniture back into a freshly carpeted room. The furniture
at approximately 11:00 a.m. on november 5, 1991, employees #1 and #2 had finished removing equipment from the top of a gr
employee #1 was installing a cooler on a 40 ft high cooling tower. He was removing the safety rigging and equipment jacks and
a power line crew was pulling leader lines over a utility pole in a swamp with water that was 1 to 3 meters deep. One of the crew
a power line crew was pulling leader lines over a utility pole in a swamp with water that was 1 to 3 meters deep. One of the crew
employees were installing a work platform inside turbine shaft #3. Employee #1 was welding from a basket lowered by a toledo
employee #1 was operating a truck loader without wearing a seat belt. When the loader rolled over a coworker was thrown from
employee #1, working to fulfill a demolition contract, was cutting away a stairway with a torch. The stairway was located betwee
employee #1 was operating a bobcat-type skid steer loader to do a small dirt job in preparation for applying an asphalt overlay o
employee #1 was driving a machine out of an excavation and backfill area where a new bridge was being built on a highway. H
on may 29, 1991, employee #1 and a coworker were attempting to repair a broken overhead door by tightening a tension spring
employee #1, the operator of a galion 5 to 8 ton roller, was repaving a blacktop street when the roller lost power while ascendin
employees were freeing up the c5 blast furnace bell rod. Chainfalls were used to regulate the fall of this 30 ton beam. At a certa
on january 22, 1992, employee #1 was landing a bundle of steel deck on the third floor structural beams, which were 26 ft 10 in
employees were preparing a large roll of plastic to seal the liner at a landfill construction site. The roll of plastic, which was 15 ft
employees were removing partition doors used to section a gym in two. After the employees lowered the 16th or 17th door to th
employees were removing partition doors used to section a gym in two. After the employees lowered the 16th or 17th door to th
employee #1 was working in an unprotected 10 ft 6 in. deep trench. The vertical walls caved in, killing him.
a power line crew was working on a deenergized overhead power line. They were working from an aerial lift. One of the employ
at 3:00 p.m. on february 25, 1993, employee #1 was lowering pipe with a roustabout winch through a mechanical shaft in a new
employee #1, an elevator maintenance mechanic, was working alone in an elevator shaft pit. He was found dead and suspende
employee #1 was assigned to remove an old sheet metal roof and to install a new one. He was last seen carrying an ax and pre


                                                       Page 11
                                                         all


workers were installing catwalks on asphalt storage tanks. Employee #1, who was not wearing fall protection, went on the catw
a construction contractor was installing a mechanical power press in a manufacturing facility with the help of the plant's employ
employee #1 was working approximately 15 ft above the ground on the roof of a barn under construction. He was dragging 4 ft
employee #1 was working on an excavation job when he had a heart attack and died.
at approximately 2:00 p.m. on may 4, 1993, employee #1 and a coworker were to install a new footer and wall along an existing
at approximately 3:00 p.m. on july 21, 1995, employee #1 was possibly greasing the u-joints on a 1970 mack dump truck. He h
some power line workers were in an aerial lift, working on an overhead power line. The employees in the aerial lift bucket move
employee #1 was struck and run over by a semi-tractor trailer's right front tire while he was moving an orange traffic safety cone
employee #1 and #2 were performing steel erection work at an approximate height of 39 ft without fall protection. Steel joists ha
employee #1 and #2 were performing steel erection work at an approximate height of 39 ft without fall protection. Steel joists ha
a concrete truck driver was pumping concrete into another concrete truck. As the driver of the second truck moved his boom in
three employees were moving a mobile scaffold. (The 24-foot-tall scaffold was being used for installing metal sheeting on a bui
the deceased was pulling electric cable across the roof with a co-worker when he fell about 30 feet to the concrete floor below.
employee #1 was sheeting a metal building from the top platform of a mobile scaffold when he suffered a heart attack. He colla
employee #1 was killed when he fell from an unsecured ladder.
an employee was installing a fascia near the ridge of the roof of a two-story public housing facility. A 12-kilovolt overhead powe
employee #1 was pulling cable for the installation of roof cameras when he fell 16 ft 7 in. through a 64 in. wide by 104 in. long fl
a mobile telephone tower station was being constructed in a rural area. Some electricians were installing the electrical service t
an elevator mechanic was troubleshooting an elevator circuit. He deenergized the main circuit and then squeezed himself throu
an ingersoll rand roller unit, model sd-70, was being moved out of the way of incoming dump trucks. Employee #1 had been as
employee #1, a laborer, was involved in demolition work using a torch to cut steel beams. He was working from an unguarded p
employee #1 was operating a manitex 1500 series boom truck crane for a tree removal service. The crane's controls are on the
at approximately 4:30 p.m. on august 29, 1996, employee #1 was operating a tree chipper in the corner of a site that was being
employee #1, a journeyman iron worker, was involved in metal sheet roofing with a detail crew approximately 32 ft above the gr
at approximately 7:50 a.m. on september 26, 1991, employees #1 and #2 were in a trench excavation at the amoco tank farm i
at approximately 7:50 a.m. on september 26, 1991, employees #1 and #2 were in a trench excavation at the amoco tank farm i
on may 29, 1992, homeowner #1 had hired marg plumbing & heating to dig a 230 ft trench on his property to install a water and
at approximately 10:15 a.m. on september 8, 1995, employee #1 was on top of the dome of a water tower under construction a
employee #1, the co-owner of the business, was on a self-propelled work platform elevated approximately 17 ft above the grou
employee working from scissor lift contacted 14.4kv power line with hand suffering fatal injuries.
employee was pouring concrete from a concrete bucket attached to a crane. (Company is installing drainage lines in the city str
the employer in this incident had been subcontracted to mill asphalt prior to its application as new asphalt pavement. Employee
an employee was operating a small derrick pump hoist mounted on a ford truck under a 12-kilovolt overhead power line. He wa
employee #1 was a laborer/oiler on a caterpillar 235 track backhoe, serial #32k08591. The operator of the backhoe was travelin
at approximately 3:30 p.m. on september 4, 1992, employee #1 was cutting a ditch line on a steep driveway using a royal mode
at approximately 7:00 a.m. on february 18, 1994, employee #1 had removed the tops of two 55 gallon metal drums using an ac
employee #1, the crew chief, and two coworkers were unloading refrigerators and appliances from a tractor trailer and placing t
two power line workers were in an aerial lift, replacing fuse links and lightning arresters on a utility pole. One of the employees,
employee #1 was lowering a gallon bucket of trash by a rope that was attached to a portable hoist. The hoist, which was not co
at approximately 7:30 a.m. on july 26, 1994, employee #1 was cutting concrete on a four lane highway. He was parallel to the tr
on or about august 18, 1994, employee #1 and a coworker, part of a crew erecting steel for a single story department store, we
a three-man crew was clearing a lot for a new home. The owner/bulldozer operator was moving brush piles and pushing over tr
a power line worker was positioning a utility pole. The pole contacted a 7200-volt overhead power line. The left side of the empl
at approximately 3:45 p.m. on november 24, 1995, employee #1 was walking to various areas along a one-story 5:12 to 8:12 pi
employee #1 was working at a demolition site tearing down an elevated railroad bridge structure. He was standing on a beam/g
employee #1 was part of a six-member crew that was installing new felt and shingles on the roof of an existing apartment buildi
employee #1 was installing roofing felt paper on the roof area of a residence. He had unrolled the felt paper and was cutting it a
employee #1 and five coworkers were installing standing seam roof decking on a pre-engineered building addition. Employee #
employee #1 was using a ladder to gain access to the roof of an existing home to inspect the chimney flue. He fell from the ladd
employee #1 was assisting in the assembly and installation of 3 in. water lines. A track hoe that was being used to create an ex
at approximately 6:20 a.m., employee #1 a job site superintendent, was supervising a water main tie in the middle of the two ea
employee was working on a new building preparing to install steel bar joists when he fell 23' from the top of the block wall to gro


                                                      Page 12
                                                         all


two employees entered a scissors lift. One employee raised the scissors lift. Once the lift reached the roof line the operator turn
located within an interior area of a manufacturing facility during the hand and mechanical demolition of a non vertically reinforce
at the time of the accident the employee (flagger) had just completed controlling the traffic flow of northbound vehicles on the h
as an employee completed the final vertical saw cut on a 17'x 6' section of precast wall, the portion being cut out fell inward ont
an 80' microwave tower was under construction at the accident site. While climbing down from the tower (at lunch time), the vic
employee #1 and a coworker were removing traffic control devices from the high speed lane of a six lane road when the arrow
three employees were using a rubber-tired, hydraulic, truck-mounted crane to remove boring equipment from a boring pit. One
employee #1 was in a trench gluing on a sleeve for a 4 in. diameter pvc sanitary sewer pipe. He was crouched down and report
at approximately 3:15 p.m. on april 29, 1991, employee #1, a painter for f. d. thomas, was on the third floor of naumes's cold st
between 3:30 and 5:30 p.m. on september 11, 1991, employee #1, of the porter yett company, was driving a koehring bomag, m
on april 27, 1992, employee #1, part of a large crew involved in the demolition of a closed down scrap battery processing plant,
at approximately 9:30 a.m. on june 2, 1992, employee #1 was driving a 1971 mack water truck on a forest service road that had
a power line crew for an electrical contractor was replacing older utility poles with new ones. One new pole had been set in a ne
victim was working atop a marklift mr 40g self propelled mobile scaffold at a height of 40 feet when the cribbing beneath the sta
victim was working atop a marklift mr 40g self propelled mobile scaffold at a height of 40 feet when the cribbing beneath the sta
engaged in re-surfacing roof. Roof six stories high victim was using a high pushed (manual) cutter with motor driven blades to r
employee #1 was cleaning an above-ground bulk storage tank from a scaffold. He was using an 8,000 psi water spray gun to b
at approximately 10:30 a.m. on april 12, 1990, employee #1 and a coworker were preparing to make a connection on an electri
employee #1 was operating a bo mag pavement rolling machine during an asphalt paving operation. He evidently was operatin
employees #1 and #2 and a coworker were working inside a building that housed a 20,000 gallon water storage tank. Employee
employees #1 and #2 and a coworker were working inside a building that housed a 20,000 gallon water storage tank. Employee
employee #1, of gm wrecking co., was watering down a building during its demolition. He was standing approximately 50 ft bac
employee #1 was standing atop the #12 stacker conveyor, approximately 8 feet from the head pulley end. When the belt was a
employee #1 was removing the bottom cleat from a building's roof while atop the roof. This task is usually performed while on a
at approximately 12:45 p.m. on january 17, 1992, employee #1 was unloading the last bundle of pipe on a lookout that was app
at approximately 11:30 a.m. on june 18, 1992, employee #1 was standing approximately 25 ft high on an extension ladder, insta
at approximately 6:45 p.m. on january 19, 1994, employee #1 had been given permission to stay late because of problems with
employees #1 and #2 were painting an elevated rail line when the scaffold suspension cable to which they had their safety belts
employees #1 and #2 were painting an elevated rail line when the scaffold suspension cable to which they had their safety belts
employee #1 was assisting a welder/burner as a fire watch in press lane 151 or 153. The burner cut the support base from und
employee #1 was installing insulating paneling on a roof when he fell 54 ft from the fifth floor roof level to the basement. He died
employees #1 and #2 were working from a morgan scaffold 24 ft above ground erecting a 28 ft tall cinderblock wall with six oth
employees #1 and #2 were working from a morgan scaffold 24 ft above ground erecting a 28 ft tall cinderblock wall with six oth
employee #1 was working on an extension ladder approximately 27 ft above the ground. He was attempting to place a cap on a
employee #1, a member of a roof decking crew, stepped from a previously installed roof deck to a building support beam. Acco
employee #1 was changing an electromagnetic brake disc on an escalator motor. He had disconnected the wire to one motor b
employee #1 was assembling a sky climber modular knock-down scaffold stage while standing on one of two platforms. The la
employee #1, for some reason, turned on the auger of a concrete paving machine after the operator had turned it off. He was p
employee #1 was operating a bulldozer when a bridge structure under demolition collapsed and fell on him. He died.
at approximately 7:30 a.m. on june 17, 1993, employee #1 was approximately 35 ft high on the roof of a school building moving
at approximately 7:26 p.m. on may 5, 1993, employee #1 was riding on a step bumper of a truck that was backing up. As the tru
at approximately 2:15 p.m. on july 22, 1993, employee #1 was removing stone pebbles from a one-story flat roof. He sat down
an employee working on the fifth floor (the matrix area) of a rendering plant was welding some piping into place. The piping was
a power line worker was finishing the replacement of insulator bells on a three-phase overhead power line. The power line had
employee #1 was a member of the 3rd shift form removal crew which dismantled and reset 15 foot diameter telescopic tunnel l
at approximately 11:50 a.m. on november 3, 1993, employees #1, #2, #3, #4, and #5 were bolting up steel. A seat lug on the he
at approximately 11:50 a.m. on november 3, 1993, employees #1, #2, #3, #4, and #5 were bolting up steel. A seat lug on the he
at approximately 11:50 a.m. on november 3, 1993, employees #1, #2, #3, #4, and #5 were bolting up steel. A seat lug on the he
at approximately 11:50 a.m. on november 3, 1993, employees #1, #2, #3, #4, and #5 were bolting up steel. A seat lug on the he
at approximately 11:50 a.m. on november 3, 1993, employees #1, #2, #3, #4, and #5 were bolting up steel. A seat lug on the he
at approximately 11:50 a.m. on november 3, 1993, employees #1 and #2 were erecting and connecting steel. A seat lug on the
at approximately 11:50 a.m. on november 3, 1993, employees #1 and #2 were erecting and connecting steel. A seat lug on the


                                                      Page 13
                                                         all


an employee was using a texoma 600 drill rig to unload a muck bucket from a pickup truck. As he was guiding the bucket, the d
at approximately 11:15 a.m. on november 20, 1993, employee #1 was handling roofing materials on a roof approximately 30 fe
employees #1 and #2 were in a private residence installing a furnace unit. The exhaust line led from the heating unit in the base
employees #1 and #2 were in a private residence installing a furnace unit. The exhaust line led from the heating unit in the base
an employee was installing new track lighting. He was lying across metal pipes in a ceiling, splicing energized conductors. The
employee #1 was working inside a 1,000 gallon tanker that was approximately 2/3 full of cooled roofing asphalt. He was using a
employee #1, a part-time worker for a cement contractor, shoveled onto a chute in a hotel parking garage. The abrasive cut-off
employee #1 and coworkers were removing and replacing wire-reinforced, gypsum concrete roof decking on a warehouse. Afte
on november 29, 1995, employee #1 died of pneumonia after burning steel trusses. Legionella bacteria were found in the empl
at approximately 7:45 a.m. on november 9, 1995, employees #1 and #2 were dismantling a scaffold that was approximately 12
at approximately 7:45 a.m. on november 9, 1995, employees #1 and #2 were dismantling a scaffold that was approximately 12
at approximately 7:45 a.m. on november 9, 1995, employees #1 and #2 were dismantling a scaffold that was approximately 12
at approximately 7:45 a.m. on november 9, 1995, employees #1 and #2 were dismantling a scaffold that was approximately 12
on april 24, 1991, employee #1, who was in a concrete arena building, was walking on an 80 inch wide concrete floor at the top
no #1 working with another carpenter, was removing 2ft wide by 14 ft flong corrigated metal sheeting over fiberglass insulation
a condor lift with an extensible boom basket 20 to 25 feet above a concrete surface, was positioned 2 1/2 feet from a pit 67 inch
a concrete pump truck had 60 ft of boom plus 40 ft of 4 in. hose extending from the ground level over the roof edge guarding to
two employees were assigned to weld tips on steel beams. The beams were to be used for pile driving. The two employees we
two employees were assigned to weld tips on steel beams. The beams were to be used for pile driving. The two employees we
employee #1 and two coworkers were moving a bundle of nine shelving racks in a warehouse aisle in preparation for assembly
some employees had replaced a motor controller for an air compressor with a larger unit--an allen-bradley smc-plus smart mot
an employee was replacing a heat pump at a house. He removed tape from a 120-volt conductor, contacted the bare conducto
a county road construction/repair crew was assigned to repair a section of gravel road by replacing a damaged culvert. Employ
employee #1 was pulling a rock buggy during built-up roofing work. He stumbled into a ladder access opening, fell, and was kill
employees of d. powell enterprises were installing 42 in. corrugated metal pipe as an overflow from an impoundment at an aba
employees of d. powell enterprises were installing 42 in. corrugated metal pipe as an overflow from an impoundment at an aba
employees of d. powell enterprises were installing 42 in. corrugated metal pipe as an overflow from an impoundment at an aba
a crew of block layers was placing reinforcing bars in a bond beam at the top of a wall. One of these employees tied a 20-foot,
employee #1 had been loading dirt into dump trucks from a dirt storage pile. When one of the truck drivers returned to the pile f
at approximately 2:50 p.m. on may 31, 1994, employee #1 and four coworkers were plasma cutting metal tanks. Employee #1 l
at 11:00 a.m. on april 25, 1991, employee #1, a millwright, was working on the construction of a wooden retaining wall. A crane
at approximately 11:30 a.m. on july 15, 1991, employee #1 entered a 96 in. diameter reinforced concrete buried pipe to restart
at about midday on september 27, 1991, employee #1 collapsed on the job at a new prison construction site. He was doing his
at approximately 3:00 pm on september 20,1991, a 54-year-old crane operator was fatally injured. He was driving a boom-type
at approximately 9:30 a.m. on august 1, 1990, employee #1 was reroofing the parkway recreation center, kaneohe, hi. For som
at approximately 2:00 p.m. on june 5, 1990, employees #1, #2, #3, and #4, working in pairs, were unhooking the cable from a c
at approximately 2:00 p.m. on june 5, 1990, employees #1, #2, #3, and #4, working in pairs, were unhooking the cable from a c
at approximately 2:00 p.m. on june 5, 1990, employees #1, #2, #3, and #4, working in pairs, were unhooking the cable from a c
at approximately 2:00 p.m. on june 5, 1990, employees #1, #2, #3, and #4, working in pairs, were unhooking the cable from a c
a truck driver was leaning on the right side of a 19.8-metric-ton grove hydraulic boom crane (model no. Rt58 e-hs, serial no. 66
a truck driver was leaning on the right side of a 19.8-metric-ton grove hydraulic boom crane (model no. Rt58 e-hs, serial no. 66
at approximately 10:50 a.m. on august 26, 1991, employee #1 was squatting within 6 in. of a roof edge where he and a coworke
an employee was using a miller roughneck 2e constant-current ac welding generator (serial no. Jk727114) to perform an arc w
at 2:55 p.m. on september 30, 1991, employee #1 and a coworker were having a rammax compactor lowered into an approxim
at approximately 8:30 a.m. on april 14, 1992, employee #1 and his partner were carrying an approximately 40 ft long single #9 r
at approximately 10:00 a.m. on august 3, 1992, employee #1 was given the task of cleaning elevators #9 and #10. Employee #
at approximately 1:00 p.m. on september 30, 1992, employee #1 was stripping and cutting the tie wire of corrugated sheet meta
employee #1 had been talking with the trailer-truck driver at the street side of the trailer when the driver got the sign from the fo
at approximately 3:30 p.m. on june 28, 1993, employee #1 was in a front end loader bucket using an oxygen/acetylene welding
following a brief rainstorm, employee #1 was pulling a 9 tire pneumatic compactor with a 1968 case tractor (rops not required).
employee #1 was "shooting the grade" of the trench in which the crew was laying a pipeline. A 16 ft double-axle trailer disconne
a road construction crew was setting up at 7:00 a.m. employee #1 was kneeling over driving a marker stake and employee #2 w


                                                      Page 14
                                                         all


a road construction crew was setting up at 7:00 a.m. employee #1 was kneeling over driving a marker stake and employee #2 w
while directing the positioning of a manlift under a bridge beam, employee #1, walking backward, stepped in front of the rear wh
at 10:30 a.m. on september 16, 1992, employee #1 was a member of a crew that was removing and replacing corroded section
employee #1 and four coworkers were painting the roof support legs of a storage tank. After moving a rolling scaffold into place
employee #1, a newly hired laborer for daley corporation, was cutting trees, lifting, and chipping tree parts at a construction site
employee #1 and a coworker were installing a sign stub. They faced each other and alternated sledge hammer swings at the st
employee #1 and a fellow painter were on a low-pitched, corrugated sheet metal roof that had a ground to eave height over 29
at approximately 10:00 a.m. on january 2, 1992, employees #1 and #2 had made the final burn on a section of railroad trestle a
at approximately 10:00 a.m. on january 2, 1992, employees #1 and #2 had made the final burn on a section of railroad trestle a
employee #1 was alone, driving a 1980 gmc brigadier water truck with a gross vehicle weight of 49,650 lb. The truck did not ha
on march 28, 1994, employee #1, the operator of a d8 caterpillar bulldozer, was pushing river rock at the bottom of an arroyo th
some electricians working for an electrical contractor were installing new cable for an airfield lighting system at an international
employee #1 was standing in the bed of a 1979 3/4 ton ford f-250 ranger pickup, unloading equipment. The bed of the truck wa
at approximately 11:00 a.m. on january 29, 1994, employee #1 was performing a cut and fill operation while operating a caterpi
an employee working from a scissor lift was installing a modular wiring system for overhead lighting fixtures at a construction si
employee #1 was rigging metal roof decking material to a 22-ton mobile hydraulic crane. A helper signaled the crane operator t
employee #1 was setting foundation blocks under a mobile home. The wind shifted, causing the mobile home to fall off the bloc
employee #1 was one of four equipment operators who were grading in order to prepare a shallow foundation for new building c
at approximately 11:00 am on june 6, 1992, employee #1 was driving a forklift truck across the parking lot after loading barrels
due to the fact that the alkylation unit went down two days earlier, and no storage capacity was left (bullet tanks and railroad ca
due to the fact that the alkylation unit went down two days earlier, and no storage capacity was left (bullet tanks and railroad ca
due to the fact that the alkylation unit went down two days earlier, and no storage capacity was left (bullet tanks and railroad ca
on september 23, 1992, employee #1, a truck driver, and a coworker, a truck crane operator, were loading a shipment of appro
at approximately 10:00 a.m. on march 8, 1993, employee #1 was on a roof slope taking pre-cut material from a material handle
on march 3, 1992, employee #1 was on the roof of a 27 to 30 ft high metal building under construction. He was walking on the p
the cause of death was reported to be improper placement of the intubation tube that resulted in suffocation while employee #1
employee #1 was guiding a suspended load of sheet metal that was being taken off a flatbed trailer to be stockpiled. The suspe
employee #1, an apprentice lineman, was unframing an electrical utility pole while on the pole. The pole broke off at ground lev
employee #1 was clipping in a transmission conductor wire at a 13 degree angle structure. Employee #1 was not using the prop
employee #1 was building a manhole consisting of stacked concrete pipes reaching a height of approximately 20 ft. He was ins
employee #1 was using the bucket of a 1974 case 450 crawler loader to spread fill for a driveway. He was backing the loader u
two employees were standing on the ground approximately 5 ft from the structural steel supports of a main bridge tower discus
an employee was standing on the ground on the south side of a single-family dwelling. He and a coworker had removed an ant
employee #1, a laborer, was in a chimney stack on an elevated suspended scaffold approximately 350 ft high, helping bricklaye
an employee was working on the ground, assisting other employees installing a roof on a house. A thunderstorm approached th
employees #1, #5 and #6 were installing a return condensate line on a deaerator tank when a 600 hp boiler exploded from eithe
employees #1, #5 and #6 were installing a return condensate line on a deaerator tank when a 600 hp boiler exploded from eithe
employees #1, #5 and #6 were installing a return condensate line on a deaerator tank when a 600 hp boiler exploded from eithe
employees #1, #5 and #6 were installing a return condensate line on a deaerator tank when a 600 hp boiler exploded from eithe
a foreman on a power line crew was holding a reel of copper conductor that was to be installed as a pole ground for a new utilit
a foreman on a power line crew was holding a reel of copper conductor that was to be installed as a pole ground for a new utilit
employees #1, #2, #3, and #4 were working in a 16 ft deep trench laying a 30 in. drain pipe. The walls of the trench were vertica
employees #1, #2, #3, and #4 were working in a 16 ft deep trench laying a 30 in. drain pipe. The walls of the trench were vertica
employees #1, #2, #3, and #4 were working in a 16 ft deep trench laying a 30 in. drain pipe. The walls of the trench were vertica
employees #1, #2, #3, and #4 were working in a 16 ft deep trench laying a 30 in. drain pipe. The walls of the trench were vertica
employee #1, a pipefitter, was working atop a 160 ft concrete silo. There were permanent metal guardrails around the roof's pe
employee #1, who was applying rolled roof insulation, fell 25 ft through a roof opening of a building under construction. He was
employee #1 was using a screw gun held over his head when he lost his balance and fell backward off the fourth step of an 8 ft
employee #1, a roofer, was removing a temporary cover from a warehouse roof opening. He fell 37 ft to a concrete slab and wa
employees #1, #4, and #5 were dismantling a piece of machinery from a scaffold. A cut was made with a torch and the piece of
employees #1, #4, and #5 were dismantling a piece of machinery from a scaffold. A cut was made with a torch and the piece of
employees #1, #4, and #5 were dismantling a piece of machinery from a scaffold. A cut was made with a torch and the piece of


                                                      Page 15
                                                          all


employees #1, #4, and #5 were dismantling a piece of machinery from a scaffold. A cut was made with a torch and the piece of
employees #1, #4, and #5 were dismantling a piece of machinery from a scaffold. A cut was made with a torch and the piece of
employee #1 was standing on a lower level roof as he proceeded to reach up and clean debris from an upper level gutter. He w
employee #1 was driving a moxy rock hauling truck at an excavation site. While traveling up a ramp from the excavation, the tru
an employee was operating a hydraulic crane. He was electrocuted when the crane contacted an overhead power line.
employee #1, who was on foot, was backed over and killed by a road grader.
at 11:00 a.m. on november 2, 1995, employee #1 was working on the third level of a 170 ft scaffolding that was inside the prill t
this accident occurred approx. 20'to 25'from the work site; employee was attempting to escape from a boom which broke when
employee fell from a 5' high scaffold, striking his head against the concrete floor.
employee #1 was apparently standing on a piece of roofing material and kicking it to make it fit. The roofing material, a metal sh
no abstract was supplied with this report. Use the information supplied in the event-type line.
at approximately 1:50 p.m. on january 21, 1991, employee #1 was moving a baffle from bin #1 to bin #2, so that the materials s
employee #1 was standing near a cherry picker when a tractor trailer passing under the cherry picker bucket struck the arm of t
employee #1 carried mortar mix to the 16 ft elevation of a tubular welded metal frame scaffold and fell to the ground, landing on
employee #1 was dismantling a scaffold when the work platform tilted. The employee fell 60 ft to the ground floor. He died.
an all-terrain fork truck, loaded with 1,500 pounds of rebar carried at a 14 foot height, overturned while crossing a rise in elevati
employee #1, age 32, fell from the top section of a television broadcast tower. He was killed.
employee #1 was struck across the throat by a crane rope as it came loose from a tangle on a cable drum. He was killed.
employee #1 was working under a suspended loader dozer cab. A chain link in the chain suspending the cab broke and the cab
while employee #1 was driving a forklift in reverse gear, the back left wheel went over the edge of a drop-off, tilting over the fork
an employee was bolting a grounding conductor to the ground terminal on a pad-mounted transformer. The employee fell into t
employee #1 was struck from behind by a cave-in and buried with his head in the water. When his head was pulled from the wa
employee #1 was washing down his concrete truck hopper when he slipped on the wet platform. He fell into the hopper's rotatin
employee #1 was preparing to begin sandblasting inside a 36 in. diameter horizontal pipe from which an elbow had been remov
employee #1 was riding on a chip spreading machine as part of the operating crew. He was assigned to watch for overhead line
a power line worker was working from an aerial lift, moving a transformer up to a new location on a utility pole. He secured a str
employee #1 and a coworker, of gilbert texas construction corp., were directing the positioning of a lowboy trailer by a crocker c
employee #1, the driver of an earth compactor roller, was not wearing the provided seat belt when the vehicle overturned. Emp
a journeyman electrician had climbed on top of a meat cooler to work on a junction box. He contacted a 277-volt circuit part ins
an employee was guiding a load attached to a truck crane. The boom of the crane contacted a 13-kilovolt overhead power line,
employees #1, #2, and #3 were inspecting and repairing newly constructed and operational sewer lines. It is theorized that emp
employees #1, #2, and #3 were inspecting and repairing newly constructed and operational sewer lines. It is theorized that emp
employees #1, #2, and #3 were inspecting and repairing newly constructed and operational sewer lines. It is theorized that emp
on october 26, 1992, employees #1 and #2 were in an excavation, working on a water main to remove a 6 in. valve that separa
on october 26, 1992, employees #1 and #2 were in an excavation, working on a water main to remove a 6 in. valve that separa
at approximately 10:40 a.m. on may 1, 1992, employee #1 was being lifted in a bucket when the bucket disengaged from the bo
employee #1, performing demolition work on a residential house, removed a roof brace while inside the house. Employee #1 w
a power line worker was assigned to attach small vibration control devices to an overhead power line. The devices were to be in
at approximately 8:45 a.m. on october 21, 1997, employees #1 and #2 and coworkers were shoveling and removing dirt from b
employee #1, a 37-year-old labor foreman, was wrecking wooden forms over an elevator shaft opening. He was standing on th
employee #1 was walking on top of the i-beams and ceiling joists where thin aluminum soffit (ceiling) material was fastened to t
employee #1, a carpenter, was installing windows at the second story level of an apartment complex under construction. He wa
employee #1 was killed when he fell through a false ceiling while installing light fixtures at a height of 37 ft above floor level. No
at approximately 6:30 p.m. on january 7, 1993, employees #1 and #2 and a coworker were positioning a 16 ft 6 in. long by 8 ft w
at approximately 6:30 p.m. on january 7, 1993, employees #1 and #2 and a coworker were positioning a 16 ft 6 in. long by 8 ft w
a power line crew was working on a deenergized power line. The line had been deenergized so that the crew could isolate trans
employee #1 and two coworkers were removing flooring from a 20 ft by 24 ft overhead storage area during demolition of the are
at approximately 1:30 p.m. on september 8, 1993, employee #1 was welding metal beam connections to columns on the 6th flo
on november 23, 1993, employee #1 and a coworker were working inside a trench that was approximately 7 ft deep, 6 ft wide, a
employee #1 was fitting a diaphragm brace onto a girder when he lost his balance and fell 55 feet. Employee #1 was not tied of
on august 25, 1992, roofers from cbs mechanical co. were performing a roofing job at the desoto high school campus. Employe
employee #1 was working on a 40 ft high roof when he fell through a skylight and was killed.


                                                       Page 16
                                                         all


employee was working in open junction box installing a switch leg to an existing energized circuit and made contact with energi
precast panels of reinforced concrete were manufactured in waco, texas, and transported by semi-truck to a highway construct
employees #1 and #2 were riding in the back of a pickup truck placing highway construction signs on an interstate highway. The
employees #1 and #2 were riding in the back of a pickup truck placing highway construction signs on an interstate highway. The
employee #1 was walking backward up the stairs, carrying one end of a 5 1/2 ft long cabinet unit. He backed off the edge of the
a power line crew was installing a new (deenergized) overhead power line. The new line fell onto an existing 7200-volt overhea
a cable television installer was installing a line under a house. The employee was wet and in a cramped position. He was electr
on july 14, 1993, employee #1, employed by paul pague, inc., was operating an up-right flying carpet mk ii rough terrain (work p
a power line crew was installing a utility pole. One employee was operating a telelect digger-derrick truck. Three other employe
employee #1 was attempting to climb approximately 18 ft 6 in. down from the roof of a building. The 15 ft portable aluminum lad
an employee was flagging vehicles as they came into a road construction site. The company had the appropriate signage place
between 12:00 midnight and 12:30 a.m. on july 28, 1995, employee #1 was knocked down by a backing john deere grader. The
two employees were installing a new central heating and air unit in a vacant house. One of the employees had crawled beneath
an electrician was to move a 120-volt switch circuit from inside an office to an outside wall. He removed a lighting panel in the o
employee #1 and coworkers had begun removing lightweight 2 ft by 8 ft reinforced concrete panels from the deck of a roof. The
at approximately 4:00 p.m. on june 6, 1996, employees #1 and #2 and a coworker were on wall scaffolding, pouring and vibratin
at approximately 4:00 p.m. on june 6, 1996, employees #1 and #2 and a coworker were on wall scaffolding, pouring and vibratin
an employee was helping to move a sign that was suspended by a case model 580d backhoe. The operator used the backhoe
employee #1 and coworkers were raising a 25,000 lb culvert out of a creek bed using a 1 in. steel wire rope attached to a d-6 d
employee #1 and coworkers were using a 50 ton grove mobile truck crane rigged with two choker slings to lower a 6,000 lb ove
the employer was moving a house on a four lane city street. The house had been moved up to a pair of utility cables (a telepho
on may 1, 1991, at the imc fertilizer, inc., (imcf)/angus chemical company plant located in sterlington, la, a fire occurred in the a
on may 1, 1991, at the imc fertilizer, inc., (imcf)/angus chemical company plant located in sterlington, la, a fire occurred in the a
on may 1, 1991, at the imc fertilizer, inc., (imcf)/angus chemical company plant located in sterlington, la, a fire occurred in the a
on may 1, 1991, at the imc fertilizer, inc., (imcf)/angus chemical company plant located in sterlington, la, a fire occurred in the a
on may 1, 1991, at the imc fertilizer, inc., (imcf)/angus chemical company plant located in sterlington, la, a fire occurred in the a
on may 1, 1991, at the imc fertilizer, inc., (imcf)/angus chemical company plant located in sterlington, la, a fire occurred in the a
on may 1, 1991, at the imc fertilizer, inc., (imcf)/angus chemical company plant located in sterlington, la, a fire occurred in the a
on may 1, 1991, at the imc fertilizer, inc., (imcf)/angus chemical company plant located in sterlington, la, a fire occurred in the a
employee #1 was standing behind a street roller, cleaning the spray nozzles. Another employee was backing a 15-ton dump tru
employee #1 was riding in the rear of a pickup truck. He was stacking traffic cones that another employee was throwing into the
an employee was guiding a concrete bucket suspended by a 22-ton crane. The crane contacted a 7900-volt overhead power lin
employee #1, a laborer, was standing near a large earth roller vehicle when he was struck by a backing water truck. Employee
employee #1 had finished his part of a truss extension operation. He had started moving his manlift away when a 50 ton truss s
employees #1 through #5 were in a trailer conducting a meeting when an exhaust stack fell on the trailer. Employee #1 was cru
employees #1 through #5 were in a trailer conducting a meeting when an exhaust stack fell on the trailer. Employee #1 was cru
employees #1 through #5 were in a trailer conducting a meeting when an exhaust stack fell on the trailer. Employee #1 was cru
employees #1 through #5 were in a trailer conducting a meeting when an exhaust stack fell on the trailer. Employee #1 was cru
employees #1 through #5 were in a trailer conducting a meeting when an exhaust stack fell on the trailer. Employee #1 was cru
employees #1 through #5 were in a trailer conducting a meeting when an exhaust stack fell on the trailer. Employee #1 was cru
employees #1 through #5 were in a trailer conducting a meeting when an exhaust stack fell on the trailer. Employee #1 was cru
employee #1 was compacting gravel on a seal coating project and had just finished a pass. The end of the pass was on a down
a drywall installer was cutting drywall with a metal-cased portable router. The router had a three-conductor power supply cord th
employee #1 was instructed to remove the rebar that was connected to concrete debris from between the scoop and the body o
a flatbed dump truck was being used to move traffic signs and cones. Employee #1 was riding on the tailgate and fell, striking h
an employee was working beneath a house, in preparation for leveling the house. He was electrocuted when he contacted an e
an employee was assigned to install a roof flange on a tin roof. As he was working, the employee contacted an exposed service
the employer was laying a 10 in. gas pipeline for a distance of 235 miles, replacing a line that had been installed in 1929. The s
at approximately 11:30 a.m. on july 19, 1992, employee #1 was told to go up on the roof of a warehouse and construct a roof o
on august 27, 1991, employee #1 was fine grading and cleaning forms, knocking off cement with a board. After working for a w
at approximately 9:05 on july 16, 1992, employee #1, of ted heine construction, was helping the owner survey the grade of a tre
at approximately 7:00 p.m. on december 3, 1992, employee #1 and three coworkers were installing carpeting in a private reside


                                                      Page 17
                                                         all


an employee was handling a cage of steel wire suspended by a crane. The operator of the p&h crane (a carpenter with no train
employee #1, a bi-directional front loader/box blade tractor driver, was trying to jump a curb with about 1,000 pounds of brick in
employees #1 and #2 were on their knees marking a survey point on the ground when a water truck backed over them. Employ
employees #1 and #2 were on their knees marking a survey point on the ground when a water truck backed over them. Employ
employee #1 was under a crane boom and removed one lower boom pin. He turned, while still under the crane, to remove the s
an employee was pulling on the load line of a crane. The load line was bunching and overlapping on the drum, and it was gettin
employee #1's head was caught between the bed of a dump truck and the truck's frame. He died.
employee #1 was working atop an elevator cage installing cables at the top of an elevator shaft. The elevator cage was secured
employees #1 and #2 of a concrete contractor were installing beam sides from an exterior platform on the eleventh floor level. T
employees #1 and #2 of a concrete contractor were installing beam sides from an exterior platform on the eleventh floor level. T
three foremen were assigned by the company's owner to remove two abandoned 6,000-gallon-capacity storage tanks approxim
at approximately 7:05 am, on august 8, 1990, employee #1 and another worker were operating a smith material hoist to lift roof
a power line worker was standing about 26 feet from a new 50-foot utility pole. He was working where a 0.375-inch-diameter te
the sole owner of a construction company was on a mobile scaffold installing angle iron in a wall curtain. He was wearing light-d
a crew of employees was constructing a concrete wall. They used a grove rt605 hydraulic crane to pick up a concrete section o
at 3:40 p.m. on december 16, 1991, employees #1 and #2 were installing roof decking atop a one story, 30 ft high building. Em
at 3:40 p.m. on december 16, 1991, employees #1 and #2 were installing roof decking atop a one story, 30 ft high building. Em
at or about 11:30 p.m. on june 23, 1992, employees #1, #2, and #3 were spray painting the inside of a water storage tank. Emp
at or about 11:30 p.m. on june 23, 1992, employees #1, #2, and #3 were spray painting the inside of a water storage tank. Emp
at or about 11:30 p.m. on june 23, 1992, employees #1, #2, and #3 were spray painting the inside of a water storage tank. Emp
at approximately 12:55 p.m. on april 16, 1992, employee #1 entered a trench attaching a rigging and shackle to the eye on one
an employee was working from an aluminum ladder, changing lighting fixtures. One of the fixtures was 6 to 8 inches above a 48
employee #1 was walking along the side of the distributor vehicle, an oil spraying truck, at the same time that the truck's driver
employee #1 and a coworker were working on a flat 32 ft high roof erecting a scaffold next to a 12 ft high wall. When the scaffo
employee #1 was crossing a 14-foot-deep basement by walking along a 6-inch i-beam located at ground level. When he attemp
employee #1 was operating a water truck at a construction site. He stopped to repair a leaking water hose under the truck while
on september 19, 1994, employees were installing a 7,000 pound heat exchange unit. The unit became unbalanced, swung ou
at approximately 8:00 a.m. on november 2, 1994, employees were driving steel beams into the ground with a pile driver and an
a plumber was working on boiler pipes in the crawl space under an existing building. A two-conductor non-metallic sheathed ca
employee #1 and a coworker were carrying a 14 ft wooden stepladder to employee #1's work area. The coworker, who was car
employees #1, #2, and #3 were performing bridge decking construction work near the center of a two lane bridge. Employee #1
a power line worker was working on a utility pole, removing equipment from it. The employee had covered energized conductor
an employee was working from an aerial lift installing a guy wire. He was holding the guy in one hand and operating the boom o
an employee was working from an aerial lift installing a guy wire. He was holding the guy in one hand and operating the boom o
employee #1 was laying brick from the top of a 5 buck scaffold when a windstorm blew the scaffold over. The employee died.
employee #1 was in the bucket of a hydraulic boom truck using a chain and sling to pull a sign pole out of the pavement. The sl
employee #1 was hanging sheetrock from a scaffold that was situated on a catwalk. The plank of the scaffold was approximate
employee #1 was helping a coworker cut away a catwalk and conveyor from a grain storage tank. The employee fell approxima
employee #1, who was engaged in construction of sheet metal decking, fell from the roof. He sustained multiple fractures and d
an employee was operating a rock drill. He was moving the drill while the boom was extended upward about 45 feet above the
employee #1 entered an unprotected trench and the wall caved in on him. He died.
an employee was climbing onto a company truck to attach a load on the truck to the load line of a hydraulic truck crane. The loa
at approximately 4:15 p.m. on june 3, 1991, employee #1 was working alongside an excavator that was digging a ditch for a ga
employee #1 was at a work site checking on his crew. He parked his truck in the emergency lane and exited from the driver's s
a power line crew was performing power line construction work. The crew was removing an existing utility pole. To accomplish
employee #1 was working on a semi-truck starter and was struck by the cab. His chest was caught between the cab and the en
a power line worker was working from an aerial lift, installing a new neutral conductor. He was wearing only leather gloves. This
employee #1, a bulldozer operator, stopped to check his hydraulic oil and inadvertently pushed the dozer's gears into reverse. T
an electrician was standing on about the fifth rung of an 8-foot fiberglass step ladder, working on a 277-volt junction box in the c
two employees, an electrician and his assistant, were reinstalling an industrial dishwasher during the renovation of a kitchen. Th
at 5:00 a.m. on july 25,1995, employee #1 was flagging traffic for a road construction crew. She was walking back to the end of
an employee was on the ground, hooking bar joists to a koering truck crane (serial no. C-14805). The 190-foot-long boom and


                                                      Page 18
                                                        all


a company was cutting trees along a roadway in rural harrison county, ky. The roadway was narrow with a fence on both sides.
at approximately 2:00 p.m. on march 12, 1992, employee #1 was walking north on highway 217 while doing shoulder work on th
at approximately 2:30 p.m. on january 27, 1994, employee #1, of don schulz roofing, fell from an upper level roof when he attem
at approximately 2:00 p.m. on august 30, 1990, employee #1 was working alone on a recently installed dock (plate) leveler. He
employee #1, a 71-year-old, experienced hydraulic excavator operator, was clearing trees and brush with the trackhoe at 11:30
an apprentice electrician was installing a conduit in a 480/277-volt panelboard. The employee was working alone. He apparentl
a contractor had been hired to decommission an approximately 2,000 gallon capacity underground gas tank from a nonfunction
a contractor had been hired to decommission an approximately 2,000 gallon capacity underground gas tank from a nonfunction
an employee parked a concrete pump truck under an overhead power line. As was the usual practice, he was going to wash ou
at approximately 11:00 a.m. on april 10, 1995, employee #1, a truck driver for del barber excavation, was west of bend, or, wate
at approximately 1:00 p.m. on june 9, 1995, employee #1, a grade checker for burl brim excavation, inc., was squatting down in
at approximately 1:00 p.m. on january 14, 1997, employee #1, a trainee, was using a rock saw track machine to cut through roc
on june 20, 1997, employee #1, a 77-year-old truck driver, was transporting a caterpillar d8h ripper bulldozer to a job site. The t
employees #1 and #2 and two coworkers were jacking up a house in preparation for the installation of a new foundation. The 32
employees #1 and #2 and two coworkers were jacking up a house in preparation for the installation of a new foundation. The 32
employee #1 was installing wiring and an electrical junction box above a chip infeed conveyor. To gain access to the electrical b
at 11:30 a.m. on january 7, 1991, employee #1 was working at his part-time job driving a 1977 gmc flatbed truck for zerniak aut
several employees were putting down felt and shingles on a 27 ft 3 in. high roof. Employee #1 was cutting shingle overlaps whil
a power line worker had gone up in a high ranger aerial lift bucket to finish setting the sag on the middle phase conductor of an
employee #1 and a coworker were using an international side boom to load pipe to be moved to another location onto a trailer.
a communications employee was repairing a telephone line. He contacted a telephone conductor that was energized at 180 vol
a crew of 3 were lashing communications(tv) cable to an overhead power pols. | employee was in a bucket truck, one ee on the
employee #1 was next to a forklift that was carrying a box when she apparently got in front of one of the lift tires and was crushe
a power line worker was installing a new utility pole to support a single-phase overhead power line. He had not covered the exis
employee #1, a certified mechanic, was working on a komatsu bulldozer without the knowledge of his employer. He was attemp
employee #1, performing his normal duties as a mechanic, was attempting to change the leaf springs on a white utility trailer. E
employee #1 had finished servicing milling machines #1 and #2 with his water truck and had parked his vehicle. A dump truck o
The owner's son decided to accompany the work crew out on a job patching pot holes in the road. When they arrived at the site
Employee #1 was performing his normal job task of land clearing by operation of heavy equipment. An employee of another co
the electrical service to a new house was energized so that the wiring could be checked. A branch circuit to the house's utility ro
an employee was working from an extension ladder, using a roller on a 7-foot-long fiberglass pole to paint the outside of a chur
employee #1 and #2, laborers, were digging a trench 3 ft deep adjacent to a 9 ft high block wall when the foundation shifted and
employee #1 and #2, laborers, were digging a trench 3 ft deep adjacent to a 9 ft high block wall when the foundation shifted and
employee #1 relocated a mobile scaffold, then climbed 12 ft to a work platform to install guardrails. The guardrails had been rem
employees #1 through #4 were cleaning up the median of an interstate highway. An automobile that was out of control ran throu
employees #1 through #4 were cleaning up the median of an interstate highway. An automobile that was out of control ran throu
employees #1 through #4 were cleaning up the median of an interstate highway. An automobile that was out of control ran throu
employees #1 through #4 were cleaning up the median of an interstate highway. An automobile that was out of control ran throu
some employees were using a grove rt 500c hydraulic crane to move a concrete screed from one end of a bridge to another. T
an electrical contractor and a local electric cooperative were working together to deenergize and reroute power lines at a substa
employee #1 was a flagman coordinating traffic at a jobsite where a pipe at the the side of the highway was being replaced usin
employee #1 was using a crane and crane basket to check the overhead crane rails installed the previous week because the ov
the excavation's left wall, near a building, caved in, burying an employee and trapping the legs of another. The other employees
employee #1 was trying to get onto a moving digger. He slipped and fell and was rolled up by the digger's back tires. Employee
employee #1 fell about 38 ft 5 in. from the fourth floor. He died.
employee #1 was on an exterior side wall of the monte tower building, working on a scaffold 45 ft from floor level. He fell and di
at approximately 11:00 a.m. on september 2, 1991, employee #1, a technician, was repairing the lock of a door on elevator #3 o
at approximately 11:50 a.m. on november 21, 1991, employee #1 was working in the electric room, located in the core of the el
employee #1 was on the second level installing communication equipment. He jumped approximately 7 ft instead of using the p
some employees were using a crane to move a 39-foot-long rail. The employees lost control of the rail, and it contacted an ove
some employees were using a crane to move a 39-foot-long rail. The employees lost control of the rail, and it contacted an ove
at approximately 8:30 a.m. on october 30, 1992, a drunken driver lost control of his vehicle and struck employees #1 through #4


                                                     Page 19
                                                         all


at approximately 8:30 a.m. on october 30, 1992, a drunken driver lost control of his vehicle and struck employees #1 through #4
at approximately 8:30 a.m. on october 30, 1992, a drunken driver lost control of his vehicle and struck employees #1 through #4
at approximately 8:30 a.m. on october 30, 1992, a drunken driver lost control of his vehicle and struck employees #1 through #4
a 35-year-old electrical technician was inspecting an electric freezer. He apparently contacted an energized part and was electr
while attempting to remove a lumber form from a scaffold, employee #1 cut the wire that tied the scaffold to the wall. The scaffo
an electrical worker was clearing insulators from a sectionalized transformer. He apparently contacted an energized part and w
employee #1 was working inside a 5 ft wide by 6 ft deep by 30 ft long trench. A cave-in occurred, covering employee #1 to his n
while cleaning soil and debris from a construction area, employee #1 was struck and killed by a falling cement pole.
employee #1 was holding a cement pile waiting for the hammerhead to settle. He lost control of the pile. The pile hit him in the f
an employee was repairing a leak in a drain from the roof of a residential terrace. A gust of wind blew an overhead power line n
employee #1 was at a height of 8 ft, installing an exit sign from a ladder. When he tried to reach an electrical cord, he suddenly
at approximately 1:30 p.m. in october, employee #1 fell from the back platform of a ford 350 truck. He was run over and killed b
an employee was electrocuted when he contacted a high-voltage cable.
employee #1 was killed instantly when part of a crane boom broke off and fell on him. He was aligning forms under the crane b
employee #1 was repairing a pipeline system when he entered a manhole without proper ppe. Employee #2 tried to rescue emp
employee #1 was repairing a pipeline system when he entered a manhole without proper ppe. Employee #2 tried to rescue emp
employee #1 was repairing a pipeline system when he entered a manhole without proper ppe. Employee #2 tried to rescue emp
employee #1 was dismantling a 30 foot tubular welded frame scaffold while standing on a 20 inch walkboard. He lost his balanc
a coworker stated that he heard a moan and saw employee #1 fall to the floor with his eyes closed and his arms downward. Do
employee #1, the operator, was cleaning a road with a caterpillar d4. The machine was climbing the road and lost force. It move
a trench wall collapsed while employees #1 and #2 were working inside. The employees died of asphyxia.
a trench wall collapsed while employees #1 and #2 were working inside. The employees died of asphyxia.
at approximately 1:00 p.m. on november 29, 1996, employee #1 was operating a komatsu d65a to clear a trail for the construct
a supervisor was connecting an elbow onto a straight run of pvc conduit. He was pushing the free end of the elbow up into the b
employee #1 was in a trench when it caved in. He died of asphyxia.
employee was working from a digger/derrick mounted basket when he made contact (unintentional) with a live 7.2 kv powerline
two employees, a dump truck driver employed by one company and a bobcat operator employed by another company, were sp
employee #1 was operating a crawler crane when it overturned into a sludge pond at a sewage disposal plant. He was asphyxia
Crew of 8 persons installing a traffic signal light with a cross-arm extending over traffic land. Lifted into position with boom of a
Crew of 8 persons installing a traffic signal light with a cross-arm extending over traffic land. Lifted into position with boom of a
Employee was involved with a brick laying operation at a residential construction project. Working on a scaffold area 11' up. No
on july 10, 1998 at 10:50 am the pedestrian walkway attached to a railroad trestle collapsed under the weight of a truck type fro
a crew of 45 men were repaving a two lane section of highway 52 south near the willow creek bridge. The crew was working tow
employees #1, #2, and #3, construction riggers, were bolting the top half section of a tube-type, wind-driven, power generation
employees #1, #2, and #3, construction riggers, were bolting the top half section of a tube-type, wind-driven, power generation
employees #1, #2, and #3, construction riggers, were bolting the top half section of a tube-type, wind-driven, power generation
employee #1 and a coworker were independent tv cable installation subcontracting technicians. They were preparing for a high
on february 7, 1997 at 5 pm, two men were attempting to put siding on a two story house. They had four sections of waco scaff
on january 3, 1998 at 8:30 am (start of shift) employee slid an impact wrench down a 1 and 12 pitch roof to position it near roof
on january 20, 1997, at approximately 9 am employee 3.1 was standing on top of the steel bar joists and with a tape measure w
at approximately 1:10 p.m. on april 18, 1990, employee #1 and a coworker were dismantling a 72 ft lattice boom from a 35 ton
at approximately 6:00 a.m. on january 17, 1991, employee #1 was driving a bmc hydra-hammer (concrete buster) from one job
at approximately 1:05 p.m. on august 5, 1991, employee #1 was spraying urethane insulation from a mobile scaffold elevated a
an employee was drilling a hole through the foundation of a house. The drill was said to be double insulated. The drill bit contac
a journeyman electrician was troubleshooting a 480-volt control circuit for a conveyor system. The conveyor was used to receiv
at approximately 4:15 p.m. on july 18, 1990, employee #1 was helping two coworkers fill a bridge abutment wing wall piling. The
at about 2:20 p.m. on july 10, 1992, employee #1, a welder/mechanic/heavy equipment repairman, was going to remove a whe
at approximately 9:30 a.m. on october 19, 1992, employee #1 and a coworker, carpenter/roofers, climbed to the top roof of a re
at approximately 10:30 a.m. on july 24, 1990, employee #1 and a coworker, both state inspectors, were setting up equipment to
employee #1 was using a jlg 40ha lift to strip concrete from the underside of a railroad bridge. The jlg lift was on the railroad tra
an electrician was called to remove some energized conductors that were encountered by some construction workers who were
emloyee #1 was riding in a standing position on a truck loaded with straw bales. The height of the uppermost bales was approx


                                                      Page 20
                                                         all


employee #1, a cement finisher on a bridge joint replacement job, was finishing cement after forms had been pulled on a pier c
at 2:22 p.m., on september 28, 1992, employee #1 was unloading a komatsu d31a-16 tiltdozer from a load king lowboy. The tru
at 8:04 a.m. on october 14, 1992, employee #1 was under his dump truck. A coworker who needed the truck moved got into it a
employee was in process of loading trailer with concrete forms was last seen stading on top of load. Fell approx. 11' 6" to groun
employee #1 was raising the scaffold outriggers and foot planks when he fell from the scaffold frame he was perched on. He la
employee #1 was laying roof decking on structural steel when he fell. He died.
employee #1 was replacing bricks in a manhole that was located in the center of a new street. The employee's body was half in
an employee was operating a black & decker 0.75-inch hammer, chiseling through a brick parapet. The flexible extension cord
at approximately 8:30 p.m. on july 13, 1990, employee #1 was dropped off at a work site. He went up to the roof to get his tools
an employee was working from a grounded aerial lift at a height of about 25 feet, connecting an electrical service for a residenc
employee #1 was standing in the construction road lane, facing south, while looking up at the underside of a bridge. A dump bo
at approximately 10:56 a.m. on july 10, 1991, employee #1 was standing near an open excavation signaling a dump truck with a
at approximately 9:00 a.m. on july 15, 1991, employee #1, of pratt & whitney, and two coworkers were cleaning in an asbestos
at approximately 7:59 a.m. on august 7, 1991, employee #1 was checking for leaks in the brazing on copper tubing when a sud
a carpenter working for a construction company was performing some demolition and remodeling work. He was electrocuted w
employee #1 was on the bed of a pickup truck hooking a chain onto a trench box. A coworker, who was in a backhoe, saw him
at approximately 1:00 p.m. on october 13, 1990, employee #1 was painting the inside of an airplane hanger when he fell 40 ft to
at approximately 10:25 a.m. on december 20, 1996, employee #1 and two coworkers were framing the roof over a porch area.
employee #1, having just finished pressure cleaning a third floor concrete balcony, entered the building to go to the next apartm
employee #1 was leaning against a railing while pulling up a bucket of tools attached to a rope. He fell five stories with the railin
employee #1 was stripping concrete forms when he backed off the unguarded side of the building, and fell approximately 22 ft t
a contractor had improperly wired an outside lighting fixture on a construction site. After the contractor had departed the site, an
employee #1 was striping interstate and ramp areas when he was struck and killed by a car.
on july 10, 1990, employee #1, a steel worker, was assembling and installing metal roof decking on a butler building in fort pierc
employee #1, while a portable classroom was being set on designated concrete posts, remained under the classroom, presuma
an employee was operating a bulldozer, clearing a site for a golf course. As he was knocking down a tree, one of its branches b
the employee charles russell, while giving direction to his two employees, he stepped backward and fell through an opening of 4
a plumber was working at a single family home. Carrying an electric drill, a portable light, and an extension cord set, he entered
a barge mounted lattice boom crane was being used to land and jump concrete sea wall panels while they were being jetted. T
on november 3, 1990, employee, #1, a 19-year-old painter and a lead man for vasquez painting, inc., took a defective metal lad
at approximately 11:00 a.m. on march 15, 1991, employee #1, a laborer, and his foreman were performing maintenance on the
employee #1 was the foreman of a two-man crew that was installing sprinkler systems. He had attached his safety belt and lany
employee #1 was a member of a six-person asphalt paving crew. He was standing behind a caterpillar 416 (serial #5pc06454)
an employer had a contract to replace conductors. During the course of this job, a backhoe operator/apprentice power line work
employee #1 and a coworker were operating a dredge on a 40 ft deep lake when a high pressure hydraulic hose ruptured and s
at 8 a.m. on tuesday, april 10, 1990, employee #1, a hillman and hookup man for centerline utilities construction corp., reached
employee #1 and a coworker were standing next to a concrete barrier wall that overlooked 125th street when a vehicle collided
while moving a manually-propelled mobile scaffold from one location to another, employee #1 fell 13 ft. He was killed.
at about 7:15 a.m. employee #1 had arrived at work and was waiting for his three coworkers. They arrived at 7:55 a.m. and look
employee #1 was setting up a concrete pump at the third level of a scaffold. Employee #1 was jumping up and down on the sca
employee #1 and a coworker were using jackhammers to demolish the concrete roof on which they were standing. While demo
employee #1, a mason tender, was standing on the lower planks of a scaffold and was stacking blocks from a buggy onto the to
on august 24, 1990, employee #1, who was doing yard work, was complaining of light headaches and dizziness. He lay down a
a laborer was in a trench laying pipe. A backhoe being used to assist in the operation struck an overhead power line and knock
employee #1, a cement finisher, was working at the base of an uncompleted 20 ft high wall with a poured tie beam. The snorke
on august 9, 1990, during a jack and bore operation, a work crew was passing a horizontal pipe under a railroad crossing when
a truck was stopped off the road on the north side of the westbound lane and was preparing to unload 20 ft by 2 ft pipe. One of
on july 20, 1993, several employees were working on the east shoulder of state road 70. They were shoveling asphalt from a fro
an employee was connecting a relay control box to an 277-volt emergency overhead light. He was working from a baker scaffo
employee #1 was laying roof decking when he caught his glove on the decking, lost his balance, and fell 85 ft. He was killed.
employee #1 was working from an extendible, articulating boom of a manlift, installing telephone wire. The employee was not w
employee #1, an iron worker connector who was also a working foreman, was landing a steel bar joist on beam supports. He a


                                                      Page 21
                                                        all


two employees, an operator and his helper, had finished loading roofing material onto a roof. They were moving the conveyor to
two employees, an operator and his helper, had finished loading roofing material onto a roof. They were moving the conveyor to
an employee of an electrical contractor was working from a ladder, using a conductive hole punch in an energized substation. T
employee #1 was standing on a stepladder that was placed on an 11th-story balcony. He stepped off the ladder, lost his balanc
employee #1 was walking backward as he pulled a tar pot containing approximately 60 gallons of hot tar. He stepped off the roo
employee #1, who was working the night shift, went to a lake that was being dug by a drag line to get a 5 gallon bucket of water
during a commercial dive, employee #1 was installing a sewer lateral. He drowned in approximately 8 ft of water. He lacked trai
four employees were pushing on a cylindrical concrete base that was suspended by a crane. They were guiding the base into a
four employees were pushing on a cylindrical concrete base that was suspended by a crane. They were guiding the base into a
four employees were pushing on a cylindrical concrete base that was suspended by a crane. They were guiding the base into a
four employees were pushing on a cylindrical concrete base that was suspended by a crane. They were guiding the base into a
four employees were pushing on a cylindrical concrete base that was suspended by a crane. They were guiding the base into a
employee #1 was tied off to a concrete form half, which was displaced and became unsecured. When the wind caught the form
employees were lowering equipment with a power hoist. The helper on the ground stopped the unit 2 ft from the ground to open
on november 22, 1994, employee #1, a laborer, was assigned to strip forms on the 10th floor. He was wearing a safety belt but
on february 20, 1995, employee #1 was working at a precast concrete wall unit erection site. When he walked into the lower flo
employee #1 was working at the edge of a deck, installing end caps for an overhead ceiling from a 1 1/2 in. by 6 1/2 in. by 14 ft
at the request of the owner of a new house, an electrician was moving a lighting fixture. While he was working in the attic of the
employee #1 was working as a carpenter's helper on the 8th floor. While descending to ground level, he stopped at the 6th floo
employee #1 was standing next to a wall of a building that had been partially demolished. A tie beam fell from the top of the wa
employee #1 and three coworkers were installing a tile roof on a residential structure. Employee #1 was distributing the tile on a
employee #1 was tying up conduit on a 12 ft a-frame ladder. The employee came into contact with an unknown object that caus
employee #1 was using a dump truck to move fill dirt into a lake. He backed the truck through a berm and into an approximatel
while operating the controls of a jlg lift, employee #1 had his back toward the bridge. When he arrived at the bridge section, the
employee #1 was disconnecting pallets of concrete on a bridge that was under construction. He had disconnected one side of t
employee #1 was repairing a flashing light while working on a pile hammer. He was standing within the swing radius of the cran
a four-employee crew was placing concrete barriers on a highway to close off a lane of traffic as part of a highway widening pro
on february 15, 1995, employee #1 was removing barricades in order to reopen a section of a southbound interstate highway. E
employee #1 fell off a roof and hit a vase. He suffered severe head trauma and died approximately 15 days later from a subdur
employee #1 was clearing vegetation from a 4 ft drainage canal when he hit an unanticipated 23 ft deep hole that was the resul
on march 4, 1995, employees #1, #2, and #3 were working on an elevated work platform. The platform had been modified by a
on march 4, 1995, employees #1, #2, and #3 were working on an elevated work platform. The platform had been modified by a
on march 4, 1995, employees #1, #2, and #3 were working on an elevated work platform. The platform had been modified by a
employee #1, a laborer, was shoveling rock off to the side of a newly paved road for later cleanup by a backhoe. He had been w
employee #1, a carpenter in a crew responsible for building forms, was carrying a ladder and tools across the working deck of a
the employer's crew, which included employee #1, was responsible for placing and tamping the dirt brought in by trucks to wide
employee #1 was part of a crew dumping overburden into a lake during preparation of land for residential development. The cre
on april 24, 1995, employee #1 was working with a three-person crew setting pilings into place for a sound barrier wall. When th
employee #1 was a personnel hoist operator responsible for lubricating the hoist. He was leaving work earlier than his regular d
employee #1 was standing on a ladder while removing the rubber plug of an 8 inch sewer line in a manhole. He fell from the lad
employee #1 was on a roof removing a fresh air duct that ran through it. Part of his body was hanging into the duct work while u
at 10:40 a.m. on november 25, 1990, employee #1 was driving a tractor and pulling a compactor on the shoulder of a highway.
employee #1 was working approximately 12 ft up a ladder. The ladder was in disrepair and a rung broke. Employee #1 fell, stru
employee #1 was inside an alcohol fructose dryer helping to do alterations to the rotor and the outside shell of the dryer. At the
employee #1 was assigned to operate and work from a mechanical scissor lift. He was not familiar with its operation or safety p
employee #1 was standing atop a 17 ft high 6,639 lb precast cement slab, setting it in place. A set of picking devices was instal
employees #1 and #2 were been spray painting the interior of an apartment when a gas water heater ignited the paint vapors, c
employees #1 and #2 were been spray painting the interior of an apartment when a gas water heater ignited the paint vapors, c
employee #1 was at a site that was being cleared in preparation for building construction. He was approximately 8 ft above the
a self-employed contractor was helping another contractor build a pitched roof over an existing flat roof. While standing on the p
employees #1 and #2 were putting siding onto a new house. They were approximately 20 ft high on a pump jack scaffold. As em
employees #1 and #2 were putting siding onto a new house. They were approximately 20 ft high on a pump jack scaffold. As em


                                                     Page 22
                                                        all


employee #1 was driving a michigan 175b end-loader across railroad tracks when he was struck by a train engine. The train str
employee #1 worked for the county. His job was to take the load tickets from the asphalt truck driver. Employee #1 stepped into
employee #1 and a coworker were working around a gomaco #8500 grade trimmer. Another coworker was operating the mach
at approximately 12:27 p.m. on june 8, 1992, employee #1 entered a construction area while a coworker was backing up and e
at approximately 12:27 p.m. on june 8, 1992, employee #1 entered a construction area while a coworker was backing up and e
employee #1 and a coworker were erecting a temporary roof to cover a hole in the permanent roof of a plastics plant. The temp
a 27-year-old employee had been working on a painting job for 9 hours. He was working from a 40-foot aluminum extension lad
an employee working on a pitched roof was repositioning a metal ladder. A 7200-volt overhead power line was located parallel
employee #1 was operating a concrete grinding machine that began to roll backward. He was unable to stop the machine, whic
employee #1 was assisting a friend who was building a new home. They were installing roof sheeting and covering on the gara
an employee was operating a metal-encased 0.5-inch electric drill with a 2.5-inch hole saw attachment. He was cutting a hole in
employee #1 was descending in an aerial bucket after working on a utility pole. The lifting mechanism was a hi-ranger articulati
at approximately 10:00 a.m. on january 27, 1992, employee #1 was clearing snow from a pitched roof in preparation for laying r
at approximately 12:30 p.m. on july 8, 1992, employees #1 and #2 were connecting bridge girders by installing cross braces be
at approximately 12:30 p.m. on july 8, 1992, employees #1 and #2 were connecting bridge girders by installing cross braces be
at approximately 12:30 p.m. on july 8, 1992, employees #1 and #2 were connecting bridge girders by installing cross braces be
during the construction of an overhead power line, a power line worker had climbed a pole to staple molding over a grounding c
employee #1 died from multiple injuries after falling from a roof. There were no witnesses to the accident and it is not known wh
employee #1, age 64, was operating an ingersoll-rand rough terrain forklift truck and suffered a heart attack while in the cab. Ac
employee #1 was the supervisor for the grinding part of a highway resurfacing project. The outside lane was barricaded and a f
a power line worker was in the bucket of an aerial lift, attaching protective grounds to a deenergized 34-kilovolt overhead power
an employee was holding a polypropylene tag line attached to a sling supporting a concrete utility vault. A crane was being used
employee #1 and two carpenters were laying out curb wall form in a corner 6 to 8 ft away from a floor opening. After a discussio
employee #1 and a coworker were working in a 30 ft wide, open surface tank. They were chipping cement approximately 8 ft fro
an employee was raising the mast of a cme 55 drill rig, which was used to take soil borings. The mast contacted a 12-kilovolt (p
employee #1, an iron worker, was standing 23 ft above the ground on a 6 inch wide steel truss receiving bundles of metal roof d
employee #1 had been laying roofing material on a long narrow section of roof. He had laid the roofing material to within 9 1/2 f
a crane was placed on the center pier of a bridge that was being demolished. The clam bucket of the crane was placed on the
employee #1, a laborer, was assisting the operator of a grade-all with cleanup. A semi-dump truck was slowly backing between
employee #1 was part of a five-man crew that was laying metal decking on bar joists; he and his foreman were sorting a bundle
a company was erecting a one-story warehouse 31 feet high. Employee #1 was welding a bar joist in a fixed position. He got up
employee #1 was repairing a residential sewer line in an 11 ft deep by 4 ft wide trench. The trench collapsed, crushing and killin
employee #1 was working on the top level of the fourth section of a scaffold. No guardrails were in place and the platform was n
employees were positioning a 22,000 pound generator with the use of a truck-mounted crane and four synthetic web slings. Wh
employees were positioning a 22,000 pound generator with the use of a truck-mounted crane and four synthetic web slings. Wh
employee #1 was moving a slow moving diesel boom snorkel lift, model #tb37d, across a three-lane highway. He was perpendi
at approximately 2:30 p.m. on november 11, 1992, employee #1 was approximately 22 ft high, working from an extension ladde
an employee was standing on the gear housing of a mixer, repairing the ballast on a fluorescent lighting fixture. The mixer had
on february 15, 1993, employee #1 was attempting to close the side-hinged gate on a tractor/trailer after dumping a load of rock
the victim was observed standing on the bark of a flatbed truck, a second employee had just handed him a concrete form to be
employee #1 was a member of a traffic signal construction crew that was installing base supports for traffic lights at an intersec
on october 16, 1990, employee #1 was preparing water main pipes for excavation work when he was caught in between the pip
employee #1 and a coworker, laborers, were installing 8 in. sanitary sewer lines and manholes in the bottom of a 12 1/2 ft deep
on february 17, 1991, employee #1, a superintendent for a general contractor, went to an inactive job site. He was apparently p
an employee was installing rain spouts on a newly constructed residence. While the employee was moving the aluminum exten
a concrete crew of 3 worker were preparing to finish pouring the floor of an underground utility vault at a water pumping station.
a concrete crew of 3 worker were preparing to finish pouring the floor of an underground utility vault at a water pumping station.
an employee was inspecting lamps in an elevated sign from an aerial lift. He removed a fluorescent lamp and contacted one en
at approximately 7:45 p.m. on january 28, 1991, employee #1 was placing fire blankets on duct work to protect the duct work fro
employees #1 through #4 were erecting structural steel when a collapse occurred, causing them to fall and to be struck by the c
employees #1 through #4 were erecting structural steel when a collapse occurred, causing them to fall and to be struck by the c
employees #1 through #4 were erecting structural steel when a collapse occurred, causing them to fall and to be struck by the c


                                                     Page 23
                                                         all


at approximately 8:15 a.m. on july 17, 1990, employee #1 was greasing the end of a section of pipe in a trench that measured a
employee #1 directed the scraper operator to cut 2 more inches of soil. After the cut was made, the operator proceeded to dum
employee #1 was using a cutting torch to burn old galvanized steel inside a culvert. After burning the steel for 30 minutes, empl
an employee was walking along the ground, guiding a box beam being moved by a truck crane. The boom of the crane contact
employee #1 was using a bull float to smooth out wet concrete floor. The garage basement wall was not completely cured but w
employee #1 was using a bull float to smooth out wet concrete floor. The garage basement wall was not completely cured but w
at approximately 2:00 p.m. on february 12, 1992, employee #1 was walking and/or moving about on metal bar joists approxima
employees #1 and #2 were on the second level of erected skeletal steel, landing bar joists to be installed as floor joists. The we
employees #1 and #2 were on the second level of erected skeletal steel, landing bar joists to be installed as floor joists. The we
at approximately 9:05 a.m. on may 19, 1992, employee #1 was helping an asphalt planer operator make a butt joint between a
employee #1, a foreman, fell approximately 712 ft through an opening in the standard guardrailing that some iron workers had r
ohio bell hired town and country industries as a subcontractor to lay fiber optic cable from lancaster to zanesville, ohio. On the m
ohio bell hired town and country industries as a subcontractor to lay fiber optic cable from lancaster to zanesville, ohio. On the m
at approximately 3:15 a.m. on december 28, 1991, employee #1, a paper machine back tender, was helping to re-align a blank
employee #1 was working in the bottom of a trench that was 13 ft deep and 4 ft wide with vertical walls. He was attempting to re
a crane operator working for a crane service contractor and two carpenters working for a residential building contractor were in
a crane operator working for a crane service contractor and two carpenters working for a residential building contractor were in
at 11:00 a.m. on february 19, 1991, employee #1 was securing/nailing plywood sheeting to trusses on the 6:12 pitch roof of a re
employee #1 was standing on top of a 5 ft high round tank, connecting a clamp to an overhead beam. The clamp was to be use
two employees were removing deenergized conductors from a cable tray as part of a small demolition project. The conductors
two employees were removing deenergized conductors from a cable tray as part of a small demolition project. The conductors
a crew of employees was performing a private driveway paving job. The job was performed with dump trucks that back into a p
a three-man demolition crew was dismantling a 120 foot high water tower. They were cutting sections of the roof and sidewall o
at approximately 8:45 a.m. on october 29, 1995, employee #1 and a coworker were installing coaxial cable to a 300 ft commun
a four-person electric utility crew was installing street lights at a us department of transportation highway project. The ground w
at approximately 7:45 a.m. on december 3, 1994, employee #1 and a coworker were installing insulation and siding on the roof
employee #1 was struck by a mack dump truck that was backing into position at an excavation site. Employee #1 died of a che
at approximately 2:50 p.m. on april 9, 1993, employees #1 through #7 and nine coworkers were working from morgan scaffolds
at approximately 2:50 p.m. on april 9, 1993, employees #1 through #7 and nine coworkers were working from morgan scaffolds
at approximately 2:50 p.m. on april 9, 1993, employees #1 through #7 and nine coworkers were working from morgan scaffolds
at approximately 2:50 p.m. on april 9, 1993, employees #1 through #7 and nine coworkers were working from morgan scaffolds
at approximately 2:50 p.m. on april 9, 1993, employees #1 through #7 and nine coworkers were working from morgan scaffolds
at approximately 2:50 p.m. on april 9, 1993, employees #1 through #7 and nine coworkers were working from morgan scaffolds
at approximately 2:50 p.m. on april 9, 1993, employees #1 through #7 and nine coworkers were working from morgan scaffolds
employee #1, a journeyman plumber, was working on a water line inside an industrial building. He was in a narrow trench abou
employees #1 through #4 were dismantling several tiers of a permanent platform structure on the front of a paper machine. The
at approximately 7:15 a.m. on march 19, 1995, employee #1 was working alone, drilling holes in a wood stud wall header plate
at approximately 10:10 a.m. on march 8, 1994, employee #1 was preparing to remove the top cross member section from an a
two employees entered an excavation to receive a load of rebar that was to be used for the construction of a retaining wall. A th
two employees entered an excavation to receive a load of rebar that was to be used for the construction of a retaining wall. A th
at approximately 5:50 p.m. on may 1, 1992, employee #1, the employer, was attempting to unhitch an air compressor from a du
on july 20, 1995, employee #1 was found lying unconscious on the second floor of a building that was under construction. There
at 2:03 p.m. on july 11, 1995, employee #1 and his foreman were replacing part of an old rusted section of a metal roof deck. E
at approximately 9:45 a.m. on january 10, 1996, employees #1 and #2 were preparing to move the flat top cover to a storm sew
at approximately 9:45 a.m. on january 10, 1996, employees #1 and #2 were preparing to move the flat top cover to a storm sew
at approximately 11:30 a.m. on november 1, 1993, employee #1 was preparing to set curbing on the fifth roof opening for which
at approximately 11:00 p.m. on january 2, 1995, employee #1 was power washing a 15-foot ceiling from a manually propelled b
at approximately 9:00 a.m. on august 12, 1991, employees #1 and #2 were preparing to remove some rigging that was attache
at approximately 9:00 a.m. on august 12, 1991, employees #1 and #2 were preparing to remove some rigging that was attache
on july 25,1991, at approximately 11:00 am the bobcat operator was preparing to get his 3rd bucket load of gravel fromthe grav
on april 18, 1994 at approximately 8:50 a.m., employee # 1 was working with three other workers who were unloading a truck th
at approximately 10:30 a.m. on april 3, 1995, employee #1 was working from a 12-foot stepladder connecting a clamp on a bar


                                                      Page 24
                                                         all


at approximately 12:15 p.m. on april 21, 1995, employee #1 was working on the ground when a 2 by 4 wooden board fell from t
employees #1 and #2, a plumber and a backhoe operator, were in a trench making a sewer and water lateral connection for a n
employee #1 had a fatal heart attack while driving on i-77. His jeep hydroplaned into a lane of oncoming traffic.
employee #1, the president, had positioned the top of a truck trailer against a one-story truck terminal that was being erected. H
employee #1 may have been electrocuted but no evidence was found. The coroner ruled that employee #1 died of a heart attac
at approximately 9:00 a.m. on october 19, 1993, employee #1 was working at a height of 100 feet installing a communication to
at approximately 3:15 p.m. on august 4, 1993, employee #1 was monitoring a pressurized sand blasting tank containing roofing
three employees were dismantling three sections of a welded-metal tubular-frame scaffold. One of the employees, who was ha
at approximately 9:55 a.m. on october 9, 1992, employee #1 was excavating alongside a natural gas pipeline. The line had bee
employee #1, working in an asbestos confinement area with elevated temperature, complained of discomfort, exited the area, c
at approximately 11:30 a.m. on march 28, 1994, employee #1 was descending the ladder of a manually-propelled elevating aer
a glue truck for p & p construction co. was driving northbound in the driving lane of i-55 at mile marker 166 near normal, il, insta
two employees were involved in operating a direct line directional boring system. One was operating the controls, and employee
employee #1 and another worker were in a trench that ran from west to east between 2 hog barns. They were installing an 8-in
employees #1 and #2 and a coworker, contractor employees, were working off a 22 ft diameter circular wooden deck suspende
employees #1 and #2 and a coworker, contractor employees, were working off a 22 ft diameter circular wooden deck suspende
an overhead power line was being upgraded from 2400 volts delta to 7200 volts. A new crossarm had been installed on the utili
at approximately 4:00 p.m. on may 31, 1990, employees #1 and #2 were completing the installation of 66 ft long roof trusses th
at approximately 4:00 p.m. on may 31, 1990, employees #1 and #2 were completing the installation of 66 ft long roof trusses th
employee #1 and a coworker were retrieving disassembled scaffold equipment that was underneath a railroad underpass and p
employee #1, a foreman, was on the roof of a building under construction at the cleveland browns training facility in berea, ohio
employee #1 was on a single-point adjustable suspension scaffold (spider lift model st 18, serial #tg 7105) at approximately 38
employees were attaching crosswalks to large tanks that contained mineral spirits and asphalt. Employee #1 struck a welding a
employee #1 was transporting a crawler/lowboy with a tractor and lowboy trailer to a site where clearing would be done. He atte
employee #1 was found dead in a partially collapsed trench. The trench was 11 to 13 ft deep, unshored, and inadequately slope
on december 4, 1992, employee #1, a supervisor for b & p industrial, inc., was on an elevated work platform (pic) in mentor, oh
on december 9, 1992, employee #1 was in an approximately 7 foot deep trench installing a sewer lateral line at a new residenti
employee #1 was working inside a trench box at a depth of 18 ft. The front wall, which was below the backhoe that was excava
employee #1 and coworkers were installing skylights in a building roof. While walking adjacent to a partially installed skylight, em
five employees were working in a 12-foot-deep excavation that measured 76 feet by 54 feet. The bottom of the excavation was
employee #1 was opening a 36 in. diameter pipe. The valve was under 1,230 psi and the valve body blew apart. Employee #1 w
employee #1 was working on or bleeding the air lines of a dump truck. There was no positive means of support provided or use
employee #1, a co-op student from the university of cincinnati, was in charge of five coworkers, two of whom were instructed to
on september 4, 1990, employees #1 and #2 were part of a crew of five iron workers and an operator who were setting and con
on september 4, 1990, employees #1 and #2 were part of a crew of five iron workers and an operator who were setting and con
the crane traveled with a suspended load on an uneven route. The crane tipped over causing the load and boom to swing arou
at about 11:00 a.m. on monday, march 22, 1993, employee #1 of harbison mahoney & higgins was working at a construction si
employee #1 was climbing a metal extension ladder to gain access to a mechanical room 9 feet 6 inches above a cement floor
employee #1 had accessed the top side of a 62 ft tall bridge pier, # ec-2, and had gone down inside it to prepare for the placem
at 1:40 p.m. on december 6, 1990, employee #1, a mason's apprentice, and a coworker were at ground level, working on a sate
on may 26, 1991, employee #1 was providing a fire watch for a coworker who was welding. When the coworker stopped workin
a plumbing apprentice was helping an excavator operator place a section of concrete pipe in a trench. The apprentice was guid
employee #1 was one of three workers on a 5:12 pitched roof deck. The workers, who were preparing to erect a window dorme
propane gas torches were being used to melt ice in the bilge of a barge. One of the torches flamed out, allowing unburned prop
employee #1 entered a 10-foot-deep trench with near-vertical side walls. The west trench wall caved in, killing employee #1.
employee #1 went completely through an asphalt pulverizer machine and was killed.
employee #1, the owner of the company, was painting and sandblasting in a suspended manbasket. He fell from the manbaske
employee #1 collapsed with hyperthermia while doing manual labor on a highway construction project. The hyperthermia induce
employee #1 was trying to secure roof deck panels that were being dislodged by high winds. He was blown off the roof edge an
employee #1 was climbing or working from a scaffold platform when he fell. He was found lying on the concrete floor, having su
the employer was engaged in a water well service operation using a portable drilling rig. The employer was air-developing a wa
employee #1 was digging around an existing sewer line in a 12 ft deep unshored trench. The east wall of the trench collapsed,


                                                      Page 25
                                                         all


employees were preparing a pug mill for hot mix at a portable asphalt batch plant. The pug mill was plugged, so the employees
employee #1 was connecting a newly installed 8 in. sewer line in a 12 foot deep trench. The trench was 3 to 4 feet wide with ne
on september 30, 1991, two employees were air nailing 2 by 4s to a ceiling. Apparently, employee #1 bent to pick up a 2 by 4 a
employee #1 was guiding the backhoe operator, while working in a trench box. The bucket of the backhoe jerked and struck em
employees #1, #2, and #3 were positioned on a personnel platform suspended from a telescoping boom crane while installing n
employees #1, #2, and #3 were positioned on a personnel platform suspended from a telescoping boom crane while installing n
employees #1, #2, and #3 were positioned on a personnel platform suspended from a telescoping boom crane while installing n
employee #1 and a coworker were attempting to locate a large valve on the side of an oil storage tank. Employee #1 was killed
employee #1 was on the roof of a two-story house which was being moved. He was moving tree limbs to clear the way when he
some employees were working on a project to install storm sewer pipe along an existing highway. During the back filling operat
the company owner and employee #1 were installing a 1 in. water line in a trench approximately 6 ft deep. The employer observ
employee #1 was on foot, assisting heavy equipment operators at a highway construction project. He had stored his water cont
employee #1, who was installing electrical sensing equipment in a roadway, was struck by a dump truck that was backing up to
at approximately 2:30 p.m., employee #1 and his coworkers were installing insulation and metal roof panels on a low-sloped 1:2
employee #1 and a coworker were dismantling and removing an overhead hoist system in their own shop. Employee #1 was op
employee #1 was working in a 6 feet deep trench when the side caved in, burying him. He was killed.
employee #1, who was working for a mobile home transport company, crawled under a mobile home to place cribbing blocks. T
employees #1 and #2 were working in a restricted lane of interstate 90 near presho, south dakota. A privately owned vehicle dr
employees #1 and #2 were working in a restricted lane of interstate 90 near presho, south dakota. A privately owned vehicle dr
employee #1 was checking the radiator fluid level on a caterpillar excavator. As he opened the radiator cap, hot fluid shot upwa
a power line worker was climbing a wood utility pole to string a new overhead power line. He was wearing a pole strap and line
employee #1 was removing built-up roofing when he removed a piece of sheet metal and fell through a roof opening. He was ki
an employee was installing rebar in a footing trench approximately 7 feet deep by approximately 3 feet wide with vertical side w
employee #1 drove his motorized broom (sweeper) into the pathway of a large truck on a highway resurfacing project. When th
employee #1 was attempting to exit from a self-propelled elevated work platform when he fell approximately 5 feet, striking his
employee #1 was lowered into a trench containing crude oil and hydrogen sulfide gas. He died of asphyxiation due to the high c
employee #1 was 15 feet above the ground connecting skeletal steel joists to i-beams. He fell from the center i-beam, contactin
employee #1 was struck by a 4,000 pound steel chute assembly. A shackle had come out of a hoist hook due to an improper ri
while dismantling a crane boom, employee #1 positioned himself under the boom's frame to pound out the key pin. When he re
employee #1 was attempting to break out a 5 ft section of drill stem with a pipe wrench that had a welded handle. The operator
an employee was dismantling an asbestos containment system from a safeway-brand scaffold that was 23 feet high. Overhead
a roofing company employee parked a 1986 ford pickup truck at the company yard and left the vehicle running. The truck rolled
a roofing company employee parked a 1986 ford pickup truck at the company yard and left the vehicle running. The truck rolled
employee #1 climbed between inadequately braced trusses, which toppled over. The employee was crushed to death between
the sole owner of a contracting firm was struck by lightning as he was performing construction work. He was electrocuted.
at approximately 12:30 p.m. on july 17, 1993, employee #1 and a coworker were preparing to string a television cable when an
an employee was repairing a broken irrigation line that was buried about 3 feet below the ground. A 480-volt conductor was bur
a power line worker climbed up the east side of a steel transmission tower to hang a hand line, which was to be used to hoist e
employee #1 was buried in a 17 ft deep trench containing previously excavated soil. He was killed. The employer did not use an
employee #1 was removing catalyst from a reactor at the conoco petroleum refinery. The reactor was overpressurized with nitro
while constructing the roof on a steel warehouse, employee #1 removed his safety belt and climbed from the manbasket onto th
in june 1995, employee #1 and a coworker were lifting an approximately 200 lb wood beam overhead. They lost control of the b
On 5/2/00 at approximately 12:00 an employee was crushed by a wooden personnel platform that was mounted to the forks of
on 7/20/98 an employee kied from injuries received while working on a scaffold approximately 15 feet in height when the scaffo
employee #1 backing up backhoe/loader with material struck employee #2 causing employee #2 to fall beneath tire and receive
on 10/1/98 at approximately 4:15 p.m. an employee died from injuries received when he was run over by an asphalt dump truck
employee was getting out of a skidster loader while it was running and his foot hit the lever and the forks came down and broke
employees #1 and #2 descended to a scaffold that was suspended by and connected to a concrete roll back forming system m
employees #1 and #2 descended to a scaffold that was suspended by and connected to a concrete roll back forming system m
employee #1 was using a tire gauge with an inflation range of 12 to 48 psi to fill a tire that had a recommended inflation of 85 ps
employee #1 was measuring and marking a centerline for the installation of reflective buttons when he walked into a moving tra
employee #1, a forklift operator with ten years of experience, was told by his supervisor to restock carpenters with supplies, suc


                                                     Page 26
                                                          all


employee #1 was cutting seized bolts when a red-hot piece of slag flew into his pocket and melted through one or two plastic di
employee #1 crawled under his dump truck while dumping snow at a snow dump and became entangled in the power take-off u
employee #1 was removing traffic signs at a work site after work was completed. Employee #1 was struck and killed by a privat
employee #1 was operating an ingersoll-rand model vr90 variable reach forklift, serial #5070b, to transport fabricated forms 100
at 7:30 a.m. on october 12, 1994, a 450e john deere crawler slid into a trench. Employee #1, the crawler operator, was found ly
some employees were drilling a dry well for a storm drainage system. The drill rig mast contacted an overhead power line, elec
employee #1, a diver, was removing a cutting head from an underwater drill. His right leg and arm were sucked into a 12 in. dia
while cutting an 8 ft by 30 in. moisture resistance drywall at the south end of a 5 ft by 11 ft upper deck, employee #1 fell 9 ft 8 in
employee #1, a dump truck operator, was working for an employer who was clearing mulched tree stumps, roots, and dirt from
employees were constructing an interlocking retaining wall at the entrance to a construction site. The retaining wall was being b
at approximately 12:30 a.m. on may 17, 1990, an explosion and flash fire occurred on the 51 ft 4 in. high tuyere service platform
at approximately 12:30 a.m. on may 17, 1990, an explosion and flash fire occurred on the 51 ft 4 in. high tuyere service platform
at approximately 12:30 a.m. on may 17, 1990, an explosion and flash fire occurred on the 51 ft 4 in. high tuyere service platform
at approximately 12:30 a.m. on may 17, 1990, an explosion and flash fire occurred on the 51 ft 4 in. high tuyere service platform
at approximately 12:30 a.m. on may 17, 1990, an explosion and flash fire occurred on the 51 ft 4 in. high tuyere service platform
at approximately 12:30 a.m. on may 17, 1990, an explosion and flash fire occurred on the 51 ft 4 in. high tuyere service platform
at approximately 12:30 a.m. on may 17, 1990, an explosion and flash fire occurred on the 51 ft 4 in. high tuyere service platform
at approximately 12:30 a.m. on may 17, 1990, an explosion and flash fire occurred on the 51 ft 4 in. high tuyere service platform
at approximately 12:30 a.m. on may 17, 1990, an explosion and flash fire occurred on the 51 ft 4 in. high tuyere service platform
employee #1, an iron worker, was setting a road steel crossbrace in place. He had both feet on the crossbrace, which was bein
on march 7, 1990, employee #1 and two coworkers, all carpenters, were on the second floor of building #4 on lot #490, assemb
employee #1 and coworkers had been working all day laying pipeline in the vicinity of owings mills, md. At the end of the day, th
employee #1 had been assigned to go from the job site at 3906 liberty heights ave. to genstar off interstate 83 north (timonium)
employee #1 was installing molding on the gable of a roof, working on a job-made lean-to scaffold. The employee climbed a lad
at approximately 10:15 a.m. on june 20, 1990, employee #1 was working on a renovation project at the robert frost intermediate
a satellite scaffold was being lowered to allow employee #1 to exit the scaffold. Employee #1 sat down on the foot boards of the
at approximately 2:28 p.m. on july 26, 1990, employee #1 was assigned to take down the scaffold on the southern end of a buil
two employees were removing a ladder hoist from the front of a building. As the employees stood the ladder up to a vertical pos
two employees were removing a ladder hoist from the front of a building. As the employees stood the ladder up to a vertical pos
at approximately 3:00 p.m. on june 26, 1990, employee #1 was working with a curb and gutter crew a short distance north of wh
employee #1 and a coworker were instructed by their foreman to set up on a ground slab in the southeastern corner of a buildin
employees #1 through #4 were sitting on steel roof beams while bolting beams to columns and connecting roof purlins to beam
at approximately 12:32 p.m. on june 17, 1992, employee #1 was working on the second floor of a residential structure, assemb
at approximately 8:15 a.m. on november 7, 1992, employee #1 was operating a 1992 bobcat skid steer loader that got stuck in
at approximately 7:00 a.m. on february 23, 1993, employee #1 and a coworker were loading bundles of oak stakes into the bac
while attempting to dismantle the boom of a bucyrus erie 25-b 35 ton truck crane employee #1 crawled under the boom and att
a power line worker had finished raising a three-conductor, 19.9-kilovolt overhead power line from an existing 35-foot pole to a
employee #1 fell approximately 40 feet from a boatswain's chair when the rigging trolley ran off the support track. He fractured
an apprentice electrician was in the attic of a two-story condominium, tracing some conductors to ascertain their function. The e
an employee had made a telephone call at an adjacent company. As he was returning to his workplace, he noticed that the tire
an employee was removing a 40-foot metal extension ladder that had been placed against the east side of a two-story house. A
an employee was using an excavator to lay a gravel bed in a 5-foot-deep, 2-foot-wide pipe trench. A 5-foot, 5-inch-high metal g
at 1:30 p.m. on june 27, 1996, employee #1 and a coworker were resealing a rubber membrane roof when the employee went t
employee #1 was operating a pavement roller on a sloping road. It malfunctioned, rolled down the road being paved, and struck
employee #1 was on a ladder installing metal around a window. He lost his balance and the ladder kicked sideways, causing hi
employee #1 was removing wires from a 50 foot high wooden pole. He cut a 1 1/2 inch diameter cable and then clipped the cab
on march 10, 1998 age 72 was on the bed of an aerial ladder truck attempting to climb onto the ladder. The ladder was in the c
seven employees were woring a roof at virginia house furniture removing an existing sheet metal roof and installing new section
The employee was working in a personnel basket hoisted by a 100 ton Linkbelt. The victim was equipped with a full body harne
while attempting to remove a pipe from under a drive systems cabinet, the cabinet fell on top of the victim, causing fatal injuries
on 12/19/98, the victim was injured when he received a 277 volt electrical shock while in the process of removing a light switch.
on 12/28/98 at approximately 10:15 a.m., the victim was removing bolts on a vertical concrete form inside of a bridge pier. He w


                                                       Page 27
                                                         all


employee working on roof removing materials. Employee stepped on unsupported portion of roof (insulation materials only) and
decedent was in the process of removing wood from a window header using a manualy propelled scaffold to stand on. The dec
two employees were disassembling the #2 fuel boiler silo from a manbasket suspended from a crane when a fire ignited causin
two employees were disassembling the #2 fuel boiler silo from a manbasket suspended from a crane when a fire ignited causin
an employee was helping to move a rubber-tired scaffold that was being towed by a van. Holding onto an attached steering bar
a contractor was completing painting and trim work on a single-family dwelling. One of the contractor's employees was on a 12
a contractor was completing painting and trim work on a single-family dwelling. One of the contractor's employees was on a 12
at approximately 9:00 a.m. on june 17, 1997, employee #1 was standing next to newly placed asphalt when he suffered a fatal
Decedent was working around an existing transformer concrete pad in order to expand it to accomodate a larger transformer. T
employees were dragging sheets of metal roof decking to point of installation. In order to try to complete a section before quittin
on 10/30/98, two employees were painting the interior of a water tank. The victim fell approimately 25 feet to the floor of the tan
employee working on bridge deck. Employee attempted to dismount deck level to a walkway 5 feet below. The walkway gave w
employee #1 was working on the roof of a pre-engineered building under construction. When he stepped from a rafter onto a g
at approximately 11:53 a.m. on april 5, 1996, employee #1 was lowering and removing h-beam supports from under the second
at approximately 11:00 a.m. on may 7, 1996, employee #1 was pulling low voltage control wiring into the ceiling of a super k-ma
an electrician was connecting a 480-volt cable to a panelboard. He was pulling the cable into position with his right hand to feed
an employee was working from a ladder jack scaffold, installing aluminum siding on a dormer on a two-story house. A section o
a crew of employees was installing telephone cable in a ceiling. They were running the cable to a security room. One of the em
at approximately 1:35 p.m. on august 8, 1997, employee #1 and two coworkers, employees of a roofing contractor, were laying
at approximately 2:45 p.m. on august 26, 1997, employee #1, who was a supervisor, and three coworkers were installing 8 ft by
at approximately 9:20 a.m. on september 2, 1997, employee #1 was walking across a landfill picking up roots and debris. A cow
employee #1 and several coworkers, of l & m contractors, inc., were moving plywood on the roof of a mcdonald's restaurant tha
on october 31, 1997, at approximately 3:45 p.m. employee #1 had cut a white oak tree that fell and lodged in another tree. The
this accident occurred on 11/5/97 at approximately 8:15 a.m. employees were in the process of off-loading concrete pilings (12
on may 14, 1996, employee #1 asked three coworkers to bring him back a sandwich when they left a job site to get some lunch
at approximately 7:40 on february 13, 1997, employee #1 was working from a 30 ft high tubular welded frame scaffold, preparin
at approximately 2:20 on march 21, 1997, employee #1 was working from a debris catch platform underneath a concrete bridge
between 2:30 and 3:00 p.m. on august 28, 1997, employees #1 and #2 were making some maintenance adjustments to a towe
between 2:30 and 3:00 p.m. on august 28, 1997, employees #1 and #2 were making some maintenance adjustments to a towe
on 11/4/97, at approx. 10:30 am, employee was working alone in a trench (6'x 6'2" wide x 33'10 long) pressurizing a new 12" na
on 6/30/99, at approx. 9:10, employee was adjusting the tailgate chains at the rear of his ford f-series dump truck #46 to contro
two of three employees installing a replacement concrete curb in a construction zone, marked off by four 18" orange traffic cone
two of three employees installing a replacement concrete curb in a construction zone, marked off by four 18" orange traffic cone
two of three employees installing a replacement concrete curb in a construction zone, marked off by four 18" orange traffic cone
on 9/2/99 at approximately 15:30 an employee (joel vargas mendoza)was nailing and trimming 1/2" x 4' x 8" particle board shea
On 1/12/00 at 2:00 PM, employee was on the roof of UV disinfection building "N" under construction at a waste water treatment
On May 12, 2001 at approximately 12:05, employee was assisting foreman in installing guardrail on partially decked sixth floor
On 6/6/01, 11:25 AM, employee was on the second floor of a residential structure under construction, receiving 4'x8' sheets of c
employee #1 was one of several workers who had been replacing terra cotta roof tiles on residences under renovation. On the
on may 24, 1996, employee #1 was on a 2 ft wide by 11 ft long by 8 1/2 ft high grove model sm2633be manlift, spray painting th
on june 18, 1999 at aprox. 1:30 pm, employee was working on the 2nd floor of a single family dwelling under construction. he w
on december 27, 1999 at approximately 10:30, employee was working on the 2nd floor of a house under construction. He was
On July 24, at approx. 11:40 am, employees #1 and #2 were working in a trench that measured approx. 26 inches wide, 25 fee
On July 20, at approximately 8:15 am, employee was working in a 3-sided wood box that mesured 4x8 feet. The box was settin
at approximately 8:30 a.m. on march 2, 1994, employee #1 was operating a john deere skid-steer loader to remove snow from
employee #1 was cutting the band on a bundle of bricks. When the band broke, the bricks knocked him off a 26 foot high scaffo
a power line worker was moving a transformer from one pole to another. As he was placing the transformer onto its mounting b
an apprentice electrician was working from a 6-foot-tall fiberglass stepladder, securing 2-foot-by-4-foot fluorescent lighting fixtu
at approximately 3:57 p.m. on october 19, 1994, employee #1 was on a steel girt at the roof line of the fuel cell area, replacing c
at approximately 2:15 p.m. on december 8, 1994, employee #1 and a coworker were working on a metal roof, placing metal de
at approximately 3:30 p.m. on december 20, 1994, employee #1 was installing sub-flooring on the 2nd floor of a townhouse und
a painting contractor (the sole owner of the business) picked up an aluminum ladder and carried it into an overhead power line.


                                                      Page 28
                                                         all


at approximately 11:15 a.m. on october 30, 1995, employee #1 and a coworker were on a job-made work platform installing sof
at approximately 9:50 a.m. on december 22, 1995, employee #1 was traveling in a case 580 backhoe. He drove the backhoe a
at approximately 2:30 p.m. on march 14, 1996, employee #1 was operating a caterpillar 621 scraper (grader pan). As he attem
On 9/4/01, at approx. 3:55 p.m., employee was setting floor joists on the second floor of a townhouse under construction, attem
at approximately 2:00 p.m. on august 22, 1994, employee #1 and a helper were scraping, glazing, and painting windows from a
at approximately 7:30 a.m. on october 7, 1994, employee #1 and a coworker loaded five 10 ft long by 6 in. wide metal curb form
At approx. 10:45 am, on 8/8/01 the victim was testing an already installed 240 volt uninterruptible power source. He borrowed a
on june 15, 1999, at approximately 8:39 am, employees #1 and #2 were lifting precast stone using a rough terrain forklift. Empl
employee #1 was working with another insulator on opposite sides of a tank, installing metal straps to secure the metal sheets
an employee was painting a switchgear cabinet inside a substation operated by an electric utility. The substation was enclosed
an employee was pulling the load line of a crane. He was going to attach it to a steel beam that was to be lifted into place on a s
an employee was installing a radio in an electric line truck. While the employee was working, the boom on the truck contacted a
on june 15, 1992, three carpenters were working beneath the east span of a poured-in-place concrete bridge, removing falsewo
on june 15, 1992, three carpenters were working beneath the east span of a poured-in-place concrete bridge, removing falsewo
on november 5, 1991, employee #1 was operating an international harvester scraper, model 412b, to move dirt on top of an em
on march 6, 1992, employee #1 was operating a caterpillar bulldozer, model d-8h, #46a29697. The employee had been site cle
employees #1 and #2 were on the platform of a genie 580 boom-supported elevated work platform and were locating conduit a
employees #1 and #2 were on the platform of a genie 580 boom-supported elevated work platform and were locating conduit a
employee #1 was standing on an aluminum platform that was secured to several brackets that had been welded onto the side o
a work crew arrived at a county bridge to drive pilings. The employees attached an 18.3-meter-long sling to the load line of a leg
a work crew arrived at a county bridge to drive pilings. The employees attached an 18.3-meter-long sling to the load line of a leg
at approximately 12:00 p.m. on february 26, 1991, employee #1 completed a meeting with an electrical construction inspector a
on september 22, 1991, employee #1 was showing a prospective buyer a house. He used a pull-down ladder in the garage to a
employee #1 was applying metal siding to the exterior wall of a building extension that extended upward from the rubberized fla
employee #1 was on a girder positioning a 10 ft long, 100 lb piece of bent iron plate when he lost his balance and fell approxima
employee #1 was a traffic signal person at a site where her employer was paving a deceleration lane along a two-lane highway
the employer was demolishing a stairway that was to be converted into an elevator shaft. The employees had been rigging sect
on october 13, 1993, the paving crew was sent to a job site to lay approximately 100 tons of asphalt. They arrived on site at abo
on october 26, 1993, an iron worker crew was installing metal decking on the roof of a skeleton steel building. Windy conditions
at approximately 8:47 a.m. on october 24, 1990, a two-ton diesel truck, traveling south at a high rate of speed in the passing lan
at approximately 8:47 a.m. on october 24, 1990, a two-ton diesel truck, traveling south at a high rate of speed in the passing lan
employee #1 and three other employees, all iron workers, were about to set stair landings in stairwell a, north side of the buildin
at approximately 3:45 a.m. on april 18, 1992, employees #1 and #2 were checking interstate construction/traffic barricades to e
at approximately 3:45 a.m. on april 18, 1992, employees #1 and #2 were checking interstate construction/traffic barricades to e
on the afternoon of march 21,1990 employee #1 was dispatched to norwell high school #215224 ossian, in. To continue the mo
victim #1 was clearing a vacant lot of second growth trees with a 1968 caterpillar model #955 when victim was struck in the hea
at approximately 2:00 p.m. on august 28, 1990, employees #1 and #2 were on the second level of a wood framed structure disc
at approximately 2:00 p.m. on august 28, 1990, employees #1 and #2 were on the second level of a wood framed structure disc
at approximately 4:00 p.m. on june 5, 1990, employee #1 was in a 7 ft 6 in. deep excavation installing wooden forms for concre
at approximately 12:15 a.m. on january 8, 1990, employees #1, #2, and #3 were arc welding boiler water wall panels from a two
at approximately 12:15 a.m. on january 8, 1990, employees #1, #2, and #3 were arc welding boiler water wall panels from a two
at approximately 12:15 a.m. on january 8, 1990, employees #1, #2, and #3 were arc welding boiler water wall panels from a two
at approximately 12:15 a.m. on january 8, 1990, employees #1, #2, and #3 were arc welding boiler water wall panels from a two
employee #1 was on his way to install the last piece of vertical siding (16 ft long by 3 ft around the side) over the top of a garage
on may 10, 1996, employee #1 was helping coworkers tear down a bucyrus erie lattice boom crawler crane. The employees ha
employee #1 was standing in an area between asphalt and construction site. A coworker was backing up a mack dump truck, m
employees #1 and #2 had obtained a soil sample from their work site and were returning to their vehicle. They walked across th
employees #1 and #2 had obtained a soil sample from their work site and were returning to their vehicle. They walked across th
employee #1 fell from a ladder, struck his head, and was killed.
a power line worker was in an aerial lift moving an overhead power line from a utility pole that was to be replaced. The employe
employee #1 was working in an excavation when its west side collapsed, killing him. The excavation was 10 feet deep. No shor
at approximately 9:00 a.m. on april 6, 1995, employee #1 and a coworker were preparing to install new gutters on a one story s


                                                      Page 29
                                                          all


on the morning of february 27, 1997, employee #1 and his partner were framing a single family home. They were installing a 4
on june 12, 1995, employee #1 and his coworkers were setting up a lattice boom american 93w crawler crane to dismantle a no
employee #1 had placed his body completely beneath a 16 ft by 70 ft mobile home that was suspended by hydraulic jacks. No c
employee #1 was a member of a crew that was installing drywall on the upper surface of a metal decked roof with a 4:12 slope.
an electrician was working in the crawl space beneath a single-family residence. As he was moving past one of the metal air-ha
an electrician was working on runway lights. He contacted energized parts of the lighting circuit and was electrocuted.
employee #1 was walking backward while pulling an electrical extension cord across a large roof. He stepped into an open, ung
employee #1 was struck and killed by a material handling truck that was backing up from a road approach. He was wearing ear
employee #1 entered a concrete manhole structure carrying a propane gas-fired blowtorch. While he was operating the torch, t
an employee was electrocuted when he tripped and fell against a power pole that was being removed from service. The power
employee #1 was on his way to work when he made a left turn in front of oncoming traffic. His vehicle was struck by a truck, an
employee #1 was working in a trench that caved in on him. He died before he could be rescued.
employee #1 was operating a highway construction machine when it rolled over and went down an embankment. He was killed
at approximately 10:00 a.m. on tuesday, december 4, employee #1 went into an unprotected trench to remove mud from aroun
a crew of employees was stringing new overhead conductors for a power line. Two of the employees were behind a spool traile
employee #1 and two coworkers were tearing off old shingles and reroofing a 12:12 pitch private residence with a 23 ft high gab
ees were on an arch type roof pressure washing the roof prior to painting it. One ee was using the pressure washer and anothe
ee's were strapping power cable to a 250 foot high cell phone tower. Employees were at approximately 140 foot level and had t
employees were completing installation of antenna system and were strapping grounds and wave guides. Deceased was in pro
a crew was installing built-up roofing on a fuel service building. Two electrical poles were located on the roof at the back side of
at approximately 4:00 p.m. on december 17, employees of shellhouse construction were laying an 8 in. sewer line. That mornin
several employees were lowering a steel plate or sheet into an open trench that was 14 feet deep. Each sheet weighed approxi
employee #1 was hired on april 6, 1993, as an industrial painter. The superintendent had known employee #1 for 15 years and
an electrician and his helper were making connections in junction box on a 120-volt circuit on the third floor of a new building. T
on monday, august 24, 1992, employee #1 was removing trash from a job site using a case 5853 four-wheel drive, rear wheel s
employee #1 was operating a 1968 r model mack water truck to wet down the right-of-way on a clay road to keep down dust an
employee #1 was in a basket attached to the boom of a digger derrick f700 truck. The pin attaching the boom to the basket bro
employee #1 was standing on an 8 ft ladder installing sheetrock nailers and hurricane clips on a ceiling adjacent to an unguarde
without fall protection, employee #1 was installing roofing felt on an 8:12 pitch roof of a private residence. He fell 24 feet to a de
employee #1, a carpenter, was 17 ft from the ground on a 6 ft long, 2 in. by 8 in. plank installing cornice trim at a 2-story residen
two employees were removing an old roof from a residence. The two employees got down from the roof to set up a 26-foot-long
two employees were removing an old roof from a residence. The two employees got down from the roof to set up a 26-foot-long
two employees were paving a frontage road and an interstate exit lane. One of the employees was standing at the side of the a
two employees were paving a frontage road and an interstate exit lane. One of the employees was standing at the side of the a
the owner and operator of a boom truck left the truck and the controls while the boom was moving slowly. He went to assist a h
on february 14, 1992, employee #1 was finishing crown work on a dormer. He was using a pneumatic nailer and hammer. Othe
employee #1, working a 7:00 p.m. to 1:00 a.m. shift, was docking a 20 ft by 8 ft, flat-hulled barge. On his way back from soundi
on january 10, 1994, employee #1 was assembling/dismantling false bottoms on a bridge under construction. While laying a sh
a power line crew was cutting down a neutral conductor in preparation for removing a transformer from a substation. Two mem
employee #1 was stepping up conduit about 15 feet from an economy scissor lift, model #sp-21-30. Employee #2 was 16 to 19
a power line worker was repairing a broken guy. Standing on the ground, the employee had the anchor in place and grabbed th
employee #1, an off-road truck driver, was dumping sand in an area to make a golf course. He was getting the dump truck into
employee #1 and coworkers were removing metal panels and old insulation. His coworkers had curled the old panels back, and
employee #1 was on the ground, first cutting up debris and then waiting for a dump truck to come on site. When the dump truck
employee #1 was working at his assigned job as a roofer. He was removing old shingles and tar paper from the roof of a 3-stor
employee #1, of the highway maintenance department, was walking behind a backing up flatbed truck. Employee #1, who was
employee #1, a drywall finisher, was sanding the ceiling in a second floor hallway. He was standing on an open-sided floor abov
two employees were moving a 40-foot-long aluminum extension ladder away from an apartment building, which they had been
two employees were moving a 40-foot-long aluminum extension ladder away from an apartment building, which they had been
on march 12, 1995, employee #1 and his uncle were welding rail brackets inside an elevator shaft at nan ya plastics. The rails h
a construction contractor was laying 203-millimeter-diameter (8-inch-diameter) ductile pipe along the side of a dirt road. The for
an employee was standing on the ground, hooking the sling from a crane onto a steel beam so that it could be hoisted. The cra


                                                       Page 30
                                                         all


employees were laying out rake angle and bolts on top of the steel rafters about 35 feet above the concrete floor. Employee #1
employee #1 and a coworker were pushing a portable lincoln ranger diesel-powered welding machine. According to a witness,
employee #1 was knocking out form pins and removing scaffolds from a concrete form that had been poured that morning whe
while wiring a silo, employees were climbing over the guardrails of a catwalk, jumping to the roof approximately 18 in. below, an
a power line contractor crew was replacing a 60-foot class 2 utility pole, crossarms, and hardware on a deenergized 69-kilovolt
a power line crew was removing a deenergized line after converting a single-phase line to a three-phase 7200-volt power line. T
a partially completed, electrically controlled supply line from a holding tank to a mixing tank was filled with dry terephthalic acid
a partially completed, electrically controlled supply line from a holding tank to a mixing tank was filled with dry terephthalic acid
employees were working from a barge replacing the pilings and fender system in a river when a small boat broke loose. Emplo
employee #1 was cleaning a freshly paved road with a massey ferguson tractor and sweeper attachment. He was being followe
employee #1 was about 100 ft high on the roof of a motel installing glass in a skylight. While walking on the skylight framework,
at approximately 2:30 p.m. on january 28, 1991, employee #1 was walking back to his work station from the break room after a
at about 4:45 p.m. on october 1, 1991, employee #1, a flagman for a road paving crew, directed the last truck of the day into po
at approximately 2:20 p.m. on february 25, 1991, employee #1 was installing an expansion joint in the boiler room piping from a
employee #1, who had been installing cable trays, was found unconscious in a genie manlift. The coroner determined that the e
employee #1 was getting a sprinkler pipe to use in the installation of automatic fire sprinklers above a permanent metal grate ty
nine employees were working as subcontractors at a chemical plant and were insulating process pipe lines with fiberglass insul
nine employees were working as subcontractors at a chemical plant and were insulating process pipe lines with fiberglass insul
nine employees were working as subcontractors at a chemical plant and were insulating process pipe lines with fiberglass insul
nine employees were working as subcontractors at a chemical plant and were insulating process pipe lines with fiberglass insul
nine employees were working as subcontractors at a chemical plant and were insulating process pipe lines with fiberglass insul
nine employees were working as subcontractors at a chemical plant and were insulating process pipe lines with fiberglass insul
nine employees were working as subcontractors at a chemical plant and were insulating process pipe lines with fiberglass insul
nine employees were working as subcontractors at a chemical plant and were insulating process pipe lines with fiberglass insul
nine employees were working as subcontractors at a chemical plant and were insulating process pipe lines with fiberglass insul
two employees (an electrician and an apprentice) of a contracting firm were being shown what work was to be done. Before the
two employees (an electrician and an apprentice) of a contracting firm were being shown what work was to be done. Before the
at approximately 8:30 a.m., employee #1 began working at a work site in portage, michigan. Employee #1 and a coworker work
on april 26, 1994, employee #1 spent the entire work shift grinding on the ground (not up in the water tank) with a hand-held gri
employee #1 and a coworker were removing a 4 ft by 8 ft piece of plywood that was covering a skylight hole. The coworker pick
on january 23, 1995, employee #1 left his work area to retrieve a part which had fallen through the grating to the level below. W
a crane was lifting ten 2 in. by 12 in. by 26 ft long wooden micro beams (planks) with two different sized nylon slings. One sling
a company had been contracted by at&t to change the antenna dish on a microwave tower. Employee #1 and a coworker were
employee #1, who was working on a garage skylight, was hoisting material from the ground to the skylight. He observed his bro
an unlicensed electrician was hired by a contractor to install 11 ceiling floodlight fixtures in a kitchen being remodeled. The emp
a crew was nearing completion of the day's work. Employee #1 was scraping or cleaning the parapet wall that had been plaster
employee #1 was walking on the roadway alongside an asphalt truck that was backing up after unloading asphalt into the lane l
while cutting and removing tree branches, employee #1 suffered an aneurism and fell approximately 8 ft to the ground. He was
employee #1 was dumping mulch from a chevy 1 ton truck. He raised the bed of the truck to allow the mulch to slide off. The m
an employee was operating a borrowed fork lift truck that was outfitted with a platform holding a large roll of plastic. The plastic
employees #1 and #2 boarded a scaffold on ground level and rode to the ninth floor, without hooking their harnesses to the lifel
employees #1 and #2 boarded a scaffold on ground level and rode to the ninth floor, without hooking their harnesses to the lifel
employee #1 was caulking seams at the northwest corner of a dome over a building when he fell about 9 ft through an opening
employee #1 and coworkers were stringing cable across a highway from an aerial truck when employee #1 removed himself fro
employee #1, a foreman, was ascending to a water tower platform from a single suspension spider stage at a municipal facility.
employee #1, a truck driver, backed a dump truck to the edge of a rock pit and began to dump his load of dirt. The truck flipped
about 7:30 a.m., employee #1, a carpenter, was completing form work at the base of a block wall. A snorkel boom that was pum
about 7:30 a.m., employee #1, a carpenter, was completing form work at the base of a block wall. A snorkel boom that was pum
at approximately 5:00 p.m. on january 23, 1997, employee #1 and four coworkers stopped working on the flat roof of a five-stor
while repairing a passenger elevator, employee #1 accidentally removed the bleeder valve while trying to bleed air from the hyd
an employee was working in a trench. A crane operator needed someone to assist him in removing a light pole several blocks a
an employee was working in a trench. A crane operator needed someone to assist him in removing a light pole several blocks a


                                                      Page 31
                                                         all


at approximately 9:30 on august 6, 1992, employee #1 was working with a pipe crew laying 18 ft by 8 in. sewer pipe in a 12 to 1
two employees were assigned to convert an electric water heater to a gas unit. They went into the crawl space under the house
two employees were assigned to convert an electric water heater to a gas unit. They went into the crawl space under the house
employee #1 was in front of a flatbed work truck resetting traffic barricades that had been set up to block a traffic lane where ro
employee #1, age 76, was a courier who obtained appropriate work licenses and permits. He fell while he was coming down a l
on may 31, 1994, a coworker, using an elevating device to deliver material to the 6th floor, allowed employees #1 and #2 to ride
on may 31, 1994, a coworker, using an elevating device to deliver material to the 6th floor, allowed employees #1 and #2 to ride
employee #1, a laborer, was discharging loads of [illegible] beams on top of scaffold shore frames. He fell, struck a column, an
an experienced power line worker was working from an aerial lift bucket, installing a crossarm on a utility pole. The employee, w
at about 1:30 p.m. in july 1993, employee #1 was painting from a scaffold, 7 stories high, and using an extension pole. He over
at approximately 10:00 a.m. on january 26, 1993, employee #1, a line worker, and a coworker were working on an overhead tra
on march 30, 1994, employee #1, a truck driver, was walking alongside a flatbed truck that was being loaded with two 18 foot c
on march 15, 1996, employee #1, a plasterer, was moving planking at a construction site. He fell, along with a plank, approxima
on august 13, 1996, employee #1 was standing 1 1/2 feet from the edge of a 24 foot high roof, discussing a job with a coworke
on june 26, 1997, employee #1 age 17, and several coworkers were repairing the leaky roof of a six-story building. The building
at approximately 7:45 a.m. on august 11, 1995, several employees were stripping manufactured form work about 15 ft high and
at approximately 7:35 a.m. on may 29, 1995, employee #1 was placing and finishing concrete at the base of one of two approxi
at approximately 7:35 a.m. on may 29, 1995, employee #1 was placing and finishing concrete at the base of one of two approxi
on september 2, 1995, employee #1 and coworkers were hot mopping a 6:12 sloped roof. Employee #1 was working about one
an employee was installing a water line in the crawl space beneath a house. He connected some extension cord sets to a recep
employee #1 was walking on a sidewalk from his truck back into the building through an open area. The employee was struck a
employee #1 was sheeting a 5:12 pitched roof with plywood. He was killed when he fell approximately 18 feet from the working
employee #1 had been hired as a laborer to tear off old roof shingles and put them in a wheelbarrow with a shovel. It was his se
employee #1 and a coworker were cutting insulation sheets and securing them to a 12:12 pitch penthouse roof. Employee #1 w
an employee was making connections to some street lights. He had completed one connection and was working on a second.
employee #1 was laying tile on a roof as a thunderstorm approached. Because of the approaching storm, the crew began to en
at approximately 12:50 p.m. on august 30, 1991, employee #1, of t & b scottdale contractors, inc., was placing concrete using a
a crew of employees had completed erecting a cellular communications tower. Because of heavy rain, the work area was limite
a crew of employees had completed erecting a cellular communications tower. Because of heavy rain, the work area was limite
employee #1 was working in a 13 ft deep by 11 ft wide by 42 ft long trench installing materials for a drainage system when the s
at approximately 10:10 a.m. on october 29, 1991, employees #1 and #2, laborers, were fitting pipe in a 12 ft deep trench. Emplo
at approximately 10:10 a.m. on october 29, 1991, employees #1 and #2, laborers, were fitting pipe in a 12 ft deep trench. Emplo
at approximately 10:30 a.m. on saturday, february 8, 1992, a cement truck arrived at a dam construction site in douglas county,
at 2:45 p.m. on october 17, 1991, employees #1, #2, and #3 were working from a suspended platform at the center truss positio
at 2:45 p.m. on october 17, 1991, employees #1, #2, and #3 were working from a suspended platform at the center truss positio
at 2:45 p.m. on october 17, 1991, employees #1, #2, and #3 were working from a suspended platform at the center truss positio
employee #1 was placing corrugated metal decking on the roof of a building under construction when he lost his balance and fe
a five-man crew was installing a concrete manhole which consisted of three cylindrical sections stacked on top of each other w
on december 15, 1993, employee #1 and a coworker, both carpenters, were installing new gutters on a house. Employee #1 wa
on march 23, 1992, employee #1 was doing waterproofing contracting work at the town center mall in kennesaw, ga. He was us
employee #1 and coworkers were digging a 6 ft wide by 8 ft deep by 15 ft long trench from east to west to install a drain line for
three employees were subcontracted out by the general contractor, procom towers, to erect a 216 foot communication tower in
employee #1 was working at ground level while his coworker stripped concrete forms above. A 4 ft by 6 ft piece of lumber fell fr
a plant was in the final stage of construction, and conductors were being run to equipment in the plant. An electrician and his he
a plant was in the final stage of construction, and conductors were being run to equipment in the plant. An electrician and his he
a plant was in the final stage of construction, and conductors were being run to equipment in the plant. An electrician and his he
employee #1 was on the roof of a water tank preparing to wash down the roof surface. He was not wearing a safety belt and lan
employee #1 was working on a roof. As he was walking across the roof, he stumbled and lost his balance. He fell off the roof an
employees #1, #2, and #3 were employed by a subcontractor hired to repair the vacuum breaker on the #3 blowtank/accumulat
employees #1, #2, and #3 were employed by a subcontractor hired to repair the vacuum breaker on the #3 blowtank/accumulat
employees #1, #2, and #3 were employed by a subcontractor hired to repair the vacuum breaker on the #3 blowtank/accumulat
employees were working at a bridge widening construction project. Two workers started moving some long rebar for a concrete


                                                     Page 32
                                                         all


employee #1 was installing electrical fixtures outdoors at the entrance of a mall that was being renovated. Employee #1 was us
employee #1, who was the president of the company, was standing with a coworker on top of two 10 ft by 11 in. containers. The
employee #1 was securing a wire rope choker to a ford truck. The choker was attached to a 950b caterpillar loader that would t
employee #1, who was employed by a form work subcontractor, was working on a hospital renovation/addition. According to a w
employee #1 was working with another employee installing a residential septic system. As the coworker dug an irregularly-shap
a four man team was assigned to install insulation along with a metal rooftop on a prefab metal building measuring 650 ft long b
a skid steer loader being used in a trash burying operation became stuck in the mud. Employee #1 entered the skid loader to d
an electrical contractor was hired by a local water department to repair rust damage and to paint inside and outside an electrica
a coworker lifted employee #1, along with an air compressor and generator for a pneumatic tool, using a platform resting on the
two employees of a road construction crew were assigned to align two traffic control signs that had blown over due to high wind
a roofer was using a fabric roofing system on a roof where the skylight openings had been covered with dome skylight covers. A
an electrical contractor had contracted with an electric cooperative to perform construction work on an overhead power line. Th
an electrical contractor had contracted with an electric cooperative to perform construction work on an overhead power line. Th
on march 20, 1995, employees #1 and #2 were instructed to go up on a light tower to make the final connection of the diagonal
on a cloudy, wet day, employee #1, a plumber, and his helper were laying the main copper water line between the slab foundati
employee #1 was installing prefabricated fireplaces at an apartment construction project. He and a coworker were carrying a fir
employees #1 and #2 were re-caulking the joints between the concrete in lanes three and four at the north end of an exit on a f
employees #1 and #2 were re-caulking the joints between the concrete in lanes three and four at the north end of an exit on a f
employee #1 had been employed for five weeks as a laborer by b&b roofing, inc., which had contracted with sims brothers cons
on march 19, 1996, employee #1, a leadman with 10 years of experience, was working on a skyway express elevated rail proje
at approximately 1:00 p.m. on january 25, 1996, employee #1, a roofing mechanic supervisor, and two coworkers were replacin
at 12:57 a.m. on january 17, 1997, employees #1 and #2 were working at the back of a slip form paver. A pickup truck drove in
at 12:57 a.m. on january 17, 1997, employees #1 and #2 were working at the back of a slip form paver. A pickup truck drove in
employee #1 had been operating a hoist in order to lower and raise materials and equipment to the ground from the roof of a fiv
employee #1 was killed and employee #2 was injured when a ladder jack scaffold collapsed. [no abstract was provided--erg]
employee #1 was killed and employee #2 was injured when a ladder jack scaffold collapsed. [no abstract was provided--erg]
employee #1 and a coworker were instructed to climb to the top of a 150 ft high steel monopole radio transmission tower to retr
employee #1 was standing beside a truck that was parked on a highway when a car traveling 45 mph came around a curve tow
the president of a company and employee #1 were measuring a roof with a 300 foot tape measure. The president was standing
on march 8, 1993, employee #1 and an assistant had been assigned by their supervisor to repair fluorescent lamps at a custom
employee #1 was working from a 6 foot baker's scaffold. Employee #1 fell, fatally striking his head on the floor.
employee #1 was helping to secure a hydraulic power unit to its frame, which was attached to a crane. After using a welding tor
some employees were installing a new air conditioning system in a residence. A helper was working in an attic space, pulling a
employee #1 and an assistant were lifted in a crane-suspended personnel platform onto a pier cap. They were going to set a pl
employee #1 was helping to load a dredge onto a transport trailer and had gotten onto the front of the trailer between the goose
an employee was working on the fourth level of a mobile scaffold. He had an aluminum extension pole in his hand. As he exited
an electrician was installing fluorescent lighting lamps and covers in a utility chase. When he finished, he began to install a swit
an employee was estimating a work order for a house. He crawled under the house to check for a connection point for a water
employee #1 was walking on the second level of a building looking overhead at the roof for nails that had missed the stud (shin
while working on the 12th floor of a building, employee #1 jumped out. The medical examiner ruled the cause of death as a suic
employee #1 was working on a barge. A steel pile was being set upright into the water and was being held upright by a chain co
employee #1 was performing stripping operations on a roof. He got a rock in his shoe and sat down on a skylight to take it out.
at approximately 5:30 p.m. on september 5, 1995, employees #1, #2, and #3 were leaving a construction site because a thunde
at approximately 5:30 p.m. on september 5, 1995, employees #1, #2, and #3 were leaving a construction site because a thunde
at approximately 5:30 p.m. on september 5, 1995, employees #1, #2, and #3 were leaving a construction site because a thunde
at 12:15 p.m. on september 16, 1995, employee #1 fell off the roof of a commercial building that was being roofed by his emplo
at about 12:30 p.m. on december 6, employee #1 was standing at the rear of a scissors truck, between the truck and the wall o
employee #1 was walking on a temporary walkway when part of the floor dislodged, causing him to fall 15 floors. He was killed.
an employee was handling an iron pipe that was suspended by a backhoe. The boom of the backhoe contacted an overhead p
employee #1 was working along the side of a roadway when a dump truck operator lost control of his vehicle, which came off th
employee #1 left his work area to attempt to pull a 10 ft ground rod using a bucket truck as a crane to lift it. He attached a piece
construction workers caught in a thunderstorm took refuge by a 9,000 lb steel pour form for protection. A foreman told them to


                                                      Page 33
                                                         all


a four-person crew was installing conductors and circuit breakers for an electric generator for a new testing station at a client's
on december 22, 1995, employee #1 was on an 8 ft aluminum ladder, spray painting the fascia board of a house under constru
at approximately 10:45 a.m. on november 21, 1995, employees #1 and #2 were working behind a guardrail in the grass median
at approximately 10:45 a.m. on november 21, 1995, employees #1 and #2 were working behind a guardrail in the grass median
two employees were dragging a sprinkler pipe at a construction site. They dragged the pipe across a 120-volt extension cord se
an employee was replacing a deteriorated utility pole supporting an overhead power line along a county road. The new pole, wh
two employees were removing a 34-foot-long, 12-inch I beam. One of the employees was sitting on the beam, which was abou
an employee was holding a load that was suspended by a hydraulic truck crane. Before the job, the crane operator and the emp
at approximately 4:00 p.m. on july 23, 1991, employees of shelby contracting co., inc., were finishing up for the day. They had b
at approximately 4:00 p.m. on april 30, 1992, employee #1 was straightening traffic control barrels in the center lane of southbo
employee #1 unloaded his load of asphalt into a screw distribution machine for paving. He pulled his truck forward about 4 to 6
at approximately 12:00 p.m. on january 17, 1995, employee #1 was free climbing a communication tower that was under constr
employee #1 was on an unguarded platform without fall protection. He was cutting a section off a 55 in. diameter duct. The piec
at approximately 11:30 a.m. on march 10, 1995, two employees were being raised by a fork truck on a 16 ft wide working platfo
at approximately 11:30 a.m. on march 10, 1995, two employees were being raised by a fork truck on a 16 ft wide working platfo
at approximately 11:30 a.m. on march 10, 1995, two employees were being raised by a fork truck on a 16 ft wide working platfo
at approximately 5:20 p.m. on march 14, 1995, employee #1 was replacing some asphalt shingles on a housetop. He suffered
a section of steel communications tower was being suspended by a crane. The crane's boom contacted a 7200-volt overhead p
at approximately 1:30 p.m. on march 29, 1995, an operator of a rough terrain forklift truck instructed a coworker to ride along an
a scaffold was attached to a crane boom. The boom on the crane contacted an overhead power line, and an employee on the s
a scaffold was attached to a crane boom. The boom on the crane contacted an overhead power line, and an employee on the s
a power line worker was on a utility pole, cutting a guy. The employee was not wearing any electrical protective equipment. He
at 10:15 a.m. on july 3, 1995, employee #1, a journeyman electrician, and a helper were changing an 8 ft long, two-tube fluores
on august 10, 1995, employee #1 was operating a street sweeper broom. He came down a hill and was unable to stop the broo
at approximately 11:30 a.m. on october 11, 1995, employee #1 was setting up an electrical cord to power a screw gun. He was
at approximately 2:00 p.m. on november 28, 1995, employee #1 was backing a d5 caterpillar dozer up metal loading ramps to a
at approximately 8:15 a.m. on march 1, 1996, employee #1 was exiting a building when he was struck by falling material that w
a crane was being used to move a compressor from one location to another when the compressor fell and struck employees #1
a crane was being used to move a compressor from one location to another when the compressor fell and struck employees #1
employee #1, of apac, inc., was unloading a rubber tire compactor from a lowboy tractor trailer. He backed the compactor off th
employee #1 was operating an aeroil roof sweeper, rs-365, and sweeping gravel into piles during built-up roofing work. There w
employee #1, a farmer working as a ditch rider, was burning weeds that were growing beside and in a dug irrigation ditch. The
at approximately 2:40 p.m. on february 25, 1992, employees #1 and #2, iron workers, were working on the steel erection of sec
at approximately 2:40 p.m. on february 25, 1992, employees #1 and #2, iron workers, were working on the steel erection of sec
employee #1 was sitting in a truck, when apparently he had a heart attack and died.
employee #1, an asbestos abatement worker, was assigned to move acm debris weighing 25 to 40 lb, 10 ft in a 4-ft-high crawl
employee #1, who was working within an excavation, was struck by a 6,000 lb steel plate (20 ft long by 8 ft high by 1 in. thick), w
employee #1 was in the bucket of an aerial lift painting a sprinkler pipe. To paint the next section of pipe, he had to go around a
on 3/16/99, we received a call from the webster police dept. that a worker was critically injured at goya foods, inc. located on go
on 5/7/99, employee #1 was attempting to place a piece of leaded copper on the dome of a church while standing on a pump ja
at approximately 2:45 p.m. on april 11, 1990, employee #1 was repairing a roof from a metal extension ladder. He apparently fe
employee #1 was starting the pony motor on a cat 583 side boom machine, #225 sheehan construction company. The machine
an employee was installing windows. He was using a portable electric screw gun supplied by a flexible cord plugged into a perm
employee #1 was in a manually propelled, hydraulic manlift that had been elevated approximately 20 feet so that he could insta
the dalton police dept. called in an event that an employee fell 17 feet from a sloped roof. Severe injuries were sustained to the
employee #1 was on a catenary-type scaffold, erected over water, that collapsed when the cables located at area #2 snapped.
on may 18, 1994, employee #1, an electronics technician, was at heyes forest products, in orange, ma, installing a moisture de
a licensed electrician had connected some 240-volt terminals for a fan housing. As he was placing this housing on a light sourc
employee #1 was attempting to set the bead of a truck tire onto a single piece rim. First he sprayed instant starting fluid into the
employee #1 was attempting to set the bead of a truck tire onto a single piece rim. First he sprayed instant starting fluid into the
at approximately 1:25 p.m. on may 28, 1991, employee #1 was walking behind the rear of a road grader that was backing up. T
employee #1 was standing on a building truss 24 ft 4 in. above the ground preparing to land a bundle of two bar joists on the tru


                                                      Page 34
                                                        all


employee #1 and four coworkers were repairing the divider between the northbound and southbound lanes of i-190. He was in
at approximately 5:30 p.m. on august 1, 1990, employee #1 was operating a forklift to unload roofing materials from a flatbed tr
a 28-year-old apprentice electrician was installing a piece of rigid conduit. The conduit apparently contacted an energized circui
employee #1 was positioning a boatswain's scaffold chair at approximately the 110 ft level of an industrial water tank tower whe
at approximately 2:55 p.m. on december 11, 1990, employee #1 was helping a coworker remove outside wood face boards from
at 9:00 a.m. on november 6, 1990, employees #1 and #2 were working in a trench, placing a 4 in. sewer pipe from a new house
at 9:00 a.m. on november 6, 1990, employees #1 and #2 were working in a trench, placing a 4 in. sewer pipe from a new house
a dump truck containing fill dirt drove up to employee #1, a loader operator, and he told the truck operator where to dump the d
at approximately 8:30 a.m. on july 22, 1991, employee #1 was standing at the rear of a cement truck that was parked in the sou
two employees were working from a scissor lift, torquing bolts on columns. Both employees contacted exposed temporary wirin
two employees were working from a scissor lift, torquing bolts on columns. Both employees contacted exposed temporary wirin
employee #1, along with an operator and a truck driver, was assigned to dismantle a link belt 45 ton friction crane. The employe
on march 23, 1993, employees #1 and #2, of washing unlimited, were cleaning the exterior of a two story brick veneer single fa
on march 23, 1993, employees #1 and #2, of washing unlimited, were cleaning the exterior of a two story brick veneer single fa
employee #1, a tandem truck driver, was a member of a north carolina department of transportation crew that was resurfacing
two employees had installed a vinyl window in a residence. They were removing a 30-foot-long aluminum extension ladder from
two employees had installed a vinyl window in a residence. They were removing a 30-foot-long aluminum extension ladder from
either employee #1 or employee #3 was attempting to cut a 2 inch metal pipe with a milwaukee metal bandsaw, serial #006789
either employee #1 or employee #3 was attempting to cut a 2 inch metal pipe with a milwaukee metal bandsaw, serial #006789
either employee #1 or employee #3 was attempting to cut a 2 inch metal pipe with a milwaukee metal bandsaw, serial #006789
on march 14, 1995, employee #1 and three coworkers working for randy hewitt construction, inc., were putting 1/2 in. by 4 ft by
on july 16, 1990, employee #1, age 21, was 27 feet above a concrete floor, moving bridging on structural steel. He lost control o
at approximately 4:30 p.m. on november 13, 1990, employees #1 through #5 were struck by a commuter vehicle at their work s
at approximately 4:30 p.m. on november 13, 1990, employees #1 through #5 were struck by a commuter vehicle at their work s
at approximately 4:30 p.m. on november 13, 1990, employees #1 through #5 were struck by a commuter vehicle at their work s
at approximately 4:30 p.m. on november 13, 1990, employees #1 through #5 were struck by a commuter vehicle at their work s
at approximately 4:30 p.m. on november 13, 1990, employees #1 through #5 were struck by a commuter vehicle at their work s
at approximately 3:38 p.m. on april 24, 1990, employee #1 was taking the final grade checks before laying a section of 18 in. pi
a laborer was adjusting a bucket suspended by a mobile crane. With the crane's outriggers extended, the crane boom was rota
employee #1 was relocating a roof skylight. When he removed the supporting structure under the roof deck that he was standin
employee #1 worked on the roof of westinghouse electric corporation for simon roofing and sheet metal corp. He worked at the
an employee was re-sagging an energized 7200-volt overhead power line. The employee was performing this task from a utility
at 1:30 a.m. on august 15, employee #1 was removing traffic lane striping from exit 6 of i-77 southbound when he was struck b
at 5:35 p.m. on december 21, 1993, employee #1 was operating a caterpillar front end loader, model 953b, to clear and grade l
a construction worker had been working with other employees throughout an afternoon, pouring concrete into a form. They wer
employee #1, a job superintendent, was preparing to shoot the next manhole when he became caught between the excavator's
at approximately 3:15 p.m. on november 4, 1993, employee #1 was working inside a catch basin cleaning out accumulations of
at approximately 10:00 a.m. on february 6, 1990, employee #1 was using a 16-foot metal 2-inch by 4-inch straightedge to smoo
at approximately 11:30 a.m. on july 23, 1990, employee #1, an electrical contractor for england's stove works, inc., was installin
at approximately 10:45 a.m. on august 8, 1994, employee #1 was in a ditchline leveling a stone in preparation for concrete to be
at approximately 11:20 a.m. on december 20, 1996, employee #1 and a coworker were installing metal flashing on a wall that w
on june 25, 1996, an employee was backing up a fuel truck to refuel a caterpillar 426 backhoe. While in reverse, the truck drive
a painter was working from an aerial lift, painting two downspouts running from a grain elevator to a grain bin. While he was wo
at approximately 7:30 p.m., employee #1 was sitting on bales of hay atop the flatbed of a ford f700 truck. The truck, believed to
employee #1 and a coworker were laying steel decking on the roof of a one-story warehouse. Employee #1 walked away from t
on january 5, 1998 at approximately 4:15 p.m., the employer was in the process of moving the trench box that was being used
On February 2, 2000, at approximately 12:08 p.m., employee #1 was in the process of mounting an L-Bracket on the Cross Arm
on april 29, 1998 at approximately 9:0 a.m., employee #1 had assisted the foreman in rigging a 32 ft. 6 in. long i-beam with a 5
on may 29, 1998 at approximately 9:00 a.m., employee #1 was preparing to remove the starter rod from the end of the boring r
employee #1 was pulling new wires from a 14 ft. high scissor lift that was moved to gain more leverage. When the lift was back
employee #1 was moving a 40 ft. extension ladder when it made contact with an overhead high voltage line. He received a life t
at approximately 11:30 a.m. on august 23, 1993, employee #1 was filling the hydraulic fluid tank between the bed and the chas


                                                     Page 35
                                                         all


at approximately 3:20 p.m. on april 27, 1994, employees #2, #3, #4, #8, and #9, iron workers, were working 35 ft above the gro
at approximately 3:20 p.m. on april 27, 1994, employees #2, #3, #4, #8, and #9, iron workers, were working 35 ft above the gro
at approximately 3:20 p.m. on april 27, 1994, employees #2, #3, #4, #8, and #9, iron workers, were working 35 ft above the gro
at approximately 3:20 p.m. on april 27, 1994, employees #2, #3, #4, #8, and #9, iron workers, were working 35 ft above the gro
at approximately 3:20 p.m. on april 27, 1994, employees #2, #3, #4, #8, and #9, iron workers, were working 35 ft above the gro
at approximately 3:20 p.m. on april 27, 1994, employees #2, #3, #4, #8, and #9, iron workers, were working 35 ft above the gro
at approximately 3:20 p.m. on april 27, 1994, employees #2, #3, #4, #8, and #9, iron workers, were working 35 ft above the gro
at approximately 3:20 p.m. on april 27, 1994, employees #2, #3, #4, #8, and #9, iron workers, were working 35 ft above the gro
at approximately 3:20 p.m. on april 27, 1994, employees #2, #3, #4, #8, and #9, iron workers, were working 35 ft above the gro
at 8:45 a.m. on monday, august 22, 1994, employee #1 was attempting to connect a tow chain to the rear of a dump truck to be
at approximately 9:20 a.m. on friday, may 12, 1995, employee #1, an iron worker, was installing a roof on a newly constructed b
employees #1 and #2 were dismantling a 10 ft by 17 1/2 ft gasoline storage tank using acetylene cutting torches when the tank
employees #1 and #2 were dismantling a 10 ft by 17 1/2 ft gasoline storage tank using acetylene cutting torches when the tank
at approximately 1:29 p.m. on april 21, 1994, employee #1 and four other employees were digging a foundation wall trench that
at approximately 12:25 p.m. on may 8, 1992, a crew of six employees was framing the second level of a two-story dormitory. Th
at approximately 12:25 p.m. on may 8, 1992, a crew of six employees was framing the second level of a two-story dormitory. Th
employee #1 was on the roof of a one-story warehouse with two coworkers installing retractable lifelines at different intervals al
employee #1 reported to work at 6:30 a.m. to raise the scaffold work platform that was installed on the non-stop elevating towe
at approximately 2:30 p.m. on may 20, 1993, employee #1 was moving traffic cones from the travel lane of interstate 64 back to
at approximately 4:00 p.m. on june 8, 1993, employee #1 had just finished checking the subgrade on a road under construction
at approximately 8:50 a.m. on september 20, 1995, employee #1 and his foreman were crossing the roof to get a load of tar wh
at approximately 1:30 p.m. on october 23, 1995, employee #1 and a coworker were walking on the roof of a locomotive repair b
at approximately 11:00 a.m. on february 12, 1996, employee #1 was laying 13 ft sections of pvc sewer pipe. He was working in
at approximately 9:15 a.m. on october 19, 1996, employee #1 was using an excavator to dig around a 5 ft dbh oak tree so that
at approximately 11:15 a.m. on december 11, 1996, employee #1 backed a dump truck onto a 20 ft long barge so that a crane
at approximately 8:15 a.m. on april 28, 1997, employee #1 was setting up a work area atop a 20 ft diameter by 45 ft high metal
an electrician was using a metal fish tape to pull new conductors through an existing 19-millimeter pvc conduit located next to a
on april 28, 1998 at approximately 10:45 a.m., employee #1 was in the process of using a chain saw to cut a 70 ft. long by ten i
employee was installing plywood decking on the second floor of a single family home under construction and going to the ladde
at approximately 12:58 p.m. on january 27, 1997, employee #1 was standing on the porch of a two-story wood home. He was p
employee #1 was on the roof at the penthouse level of a 26-story condominium as part of a balcony repair and restoration oper
employees #1 and #2 were operating an elgin street sweeper. Employee #1 was the supervisor and operator of the sweeper wh
employees #1 and #2 were operating an elgin street sweeper. Employee #1 was the supervisor and operator of the sweeper wh
on 4/15/99 in the a.m. hours, employee #1 and a helper were installing windows and doors on the interior of the future commun
on 2/17/00 at 9:50 a.m., employee was engaged in the leading edge construction of the plywood from work of the roof level dec
On Saturday April 28, 2000 at 2:45 p.m. employee # 1 was working with employees # 2 and 3 installing a new gutter on the eas
Victim was in the process of repairing the guttering at the edge of a roof above a three story building (appx. 70'). Victims foot w
Victim was working on outside lights at a school football stadium. Victim was working from a bucket truck, 70 feet above the gro
a roofer was installing a downspout on a building. As he was moving his extension ladder, he lost his footing. The ladder contac
the employees had finished laying 6-inch diameter pvc sewage line in a 10-foot deep trench and had left the trench. When emp
at approximately 11:00 a.m. on september 13, 1990, employee #1, the owner and operator of an international e-200 self-loadin
employees #1 and #2 were removing a metal forming table from its front rollers so that the table could be moved to the floor ab
employees #1 and #2 were removing a metal forming table from its front rollers so that the table could be moved to the floor ab
at approximately 11:00 a.m. on june 4, 1991, employee #1 was preparing cast iron manhole covers for painting. After preparing
an employee was using a hydraulic excavator to lower a well point and a section of metal pipe. The 27-foot, 6-inch-tall well poin
at 3:10 p.m. on september 3, 1992, employee #1 was assisting other employees in lowering roofing equipment using a manual
at approximately 12:25 p.m. on february 12, 1992, employee #1, a fourth year apprentice electrician for dorey electric co., was d
at 12:31 p.m. on may 8, 1992, employee #1 was attempting to transport a window frame unit from the second level of a duplex-
at 12:31 p.m. on may 8, 1992, employee #1 was attempting to transport a window frame unit from the second level of a duplex-
at 10:58 a.m. on april 2, 1990, a work crew from snyder sign co., johnson city, tn, was repairing sign faces on a 16 ft by 16 ft sig
a power line worker and his foreman were replacing a utility pole. The replacement pole was a 50-foot wooden pole. The power
three employees were moving a rustgo work platform. Two of the employees were pushing and the third was pulling the scaffol


                                                      Page 36
                                                       all


three employees were moving a rustgo work platform. Two of the employees were pushing and the third was pulling the scaffol
three employees were moving a rustgo work platform. Two of the employees were pushing and the third was pulling the scaffol
a contracting crew was constructing a pole barn. The foreman was working on the crest of the barn, and one of the other emplo
employee #1 was operating a caterpillar model 955 k front end loader on a 45 degree slope. The loader was moving in a sidehi
three employees were installing new aluminum gutters at a furniture company. One of the employees was standing on an alum
a three-person power line crew was repairing a downed power line. The crew foreman left the area to deenergize the overhead
at 11:00 a.m. on april 20, 1994, employee #1 was attempting to adjust a pipe in a trench measuring approximately 10 to 12 feet
at approximately 11:00 a.m. on july 13, 1994, employee #1 and a coworker were site clearing trees in a heavily wooded area. E
at 10:00 a.m. on june 2, 1994, employee #1 and a coworker, both experienced iron workers, were bolting up previously set stru
at 2:45 a.m. on august 5, 1994, employee #1, the operator, and two coworkers were loading a milling machine onto a lowboy tr
at 11:30 a.m. on october 8, 1994, employee #1 and three coworkers were installing leachate 8 in. diameter pvc piping using a jo
at approximately 9:15 a.m. on may 31, 1995, employee # 1, the employer, and a coworker were installing wheel axles under a m
at approximately 10:30 a.m. on november 20, 1995, employee #1 was on a residential construction site assisting the unloading
at approximately 2:00 p.m. on december 21, 1995, employee #1 was clearing brush from around a water settlement pond. To s
at approximately 1:30 p.m. on february 7, 1996, employee #1 was on a roof moving skylight roof panels. He stepped backward
at 1:00 p.m. on may 28, 1996, employee #1 was descending a 28 foot extension ladder when the ladder slipped, causing him to
on wednesday, april 18, 1990, employee #1, a truck driver for lmr construction co., was assisting in the loading of 10 by 12 ft m
an electrician was splicing cables in a manhole at an airport. The cables to be spliced were not energized. Two other cables we
an employee was replacing an old bulkhead with a new one. To prepare for the job, he was placing tools and running extension
at approximately 3:22 p.m. on december 18, 1990, employees #1 and #2 and five coworkers were installing wood form work fo
at approximately 3:22 p.m. on december 18, 1990, employees #1 and #2 and five coworkers were installing wood form work fo
at approximately 9:15 a.m. on june 15, 1991, employee #1 was using a 1984 ford 3910 tractor and a covington bush-hog to mo
at approximately 11:50 a.m. on july 12, 1991, employee #1 was on the fourth floor of a five-story structural steel building under
an 18-foot-long section of 24-inch-diameter ductile iron pipe was suspended from the bucket of a caterpillar 235c hydraulic exc
at approximately 12:30 p.m. on december 6, 1993, employee #1 walked around a tank on a bracket scaffold to retrieve a hamm
at approximately 1:05 p.m. on september 23, 1992, employee #1 and a coworker were moving a manually propelled hydraulic w
on friday, june 19, 1998, at approximately 10:00 a.m., employee #1 cut a 86 foot tall beech tree down with a chainsaw on a slop
On March 28, 2001, at approximately 8:00 am Employee #1 attempted to retrieve a set of keys that were stuck at the end of a t
An employee of Lang Construction Company, was killed when he came in contact with a power line and fell from the roof of a h
employee #1 was operating a tractor mower when the machine rolled into a ditch, hit a culvert, rose into the air, and then jerked
Three employees were working on an approx. 70' steel power transmission tower utilizing a bucket truck. The bucket was unab
employee #1 was driving a dump truck and pulling a lowboy. As he made a u-turn at the end of a street, he broke the right side
on november 25, 1992, employee #1 and a coworker, experienced timber fallers for tri-county construction, were working toget
at about 11:00 a.m. on october 24, 1991, employee #1 and five coworkers, of delta steel erectors, were installing a girt above th
at approximately 9:50 a.m. on february 13, 1992, employee #1 was operating a clark 4,000 lb pneumatic tire, propane-powered
at about 2:00 p.m. on march 20, 1992, employees #1 and #2, part of a five-person crew, were connecting conductors, installing
at about 2:00 p.m. on march 20, 1992, employees #1 and #2, part of a five-person crew, were connecting conductors, installing
at approximately 11:12 a.m. on april 7, 1992, employee #1 was unbanding trusses when the trusses fell forward. Employee #1
employee #1 was erecting a 180 ft radio tower. The erection phase was complete, and the crew was lowering a unit referred to
on june 25, 1994, employee #1 and a carpenter leadman were placing fabricated trusses that spanned a garage in keyes, ca. T
at 4:00 p.m. on january 17, 1993, employee #1 of john jackson masonry was driving a dynalift rough terrain forklift truck on the
at approximately 12:30 p.m. on august 17, 1991, employee #1 was riding on the right fender of a fork truck, out of the operator'
on october 9, 1991, employee #1 of r.c. collet, inc., was working on a construction project at sacramento metro airport. There w
employee #1 and two coworkers, who were working for a framing contractor, had just returned from lunch. The exterior walls ha
three employees were moving an aluminum ladder in front of a house on which they were installing siding. The ladder was exte
three employees were moving an aluminum ladder in front of a house on which they were installing siding. The ladder was exte
three employees were moving an aluminum ladder in front of a house on which they were installing siding. The ladder was exte
on december 8, 1990, employee #1 was 22 ft high installing siding on a townhouse from a pump jack scaffold. The scaffold had
injured was climbing down a 12' aluminum extension ladder when the ladder slipped on the concrete floor. This ladder did not h
employees #1 and #2 were walking toward the paving equipment in a lane that was to be paved. A dump truck that was backin
at approximately 8:20 a.m. on june 21, 1990, employee #1 and a coworker were working from two baker tubular welded mobile
employee #1, a self-employed television cable installer who had been contracted by the cate company to install tv cable line, wa


                                                    Page 37
                                                         all


a groundman was helping unload steel rebar from a trailer. The rebar was being positioned at a work location in a creek bed wi
employee #1 was placing a coated steel beam, approximately 19 ft long by 8 in. diameter, onto a roof. No tag line was used but
employee #1 was unloading blocks of asphalt at mccarran international airport. He died of an acute myocardial infarction due to
employees were sealing a wood floor in a bathroom in a new addition to an existing building. The employees had no class I, div
employee #1 and coworkers were assembling the boom of a crane. While the operator was climbing into the cab and the forem
employee #1 had on a safety belt and life line, but did not have the life line secured to anything. When he stepped up on the ed
an electrician was pulling an electrical service into a 2000-ampere, 480-volt main service panelboard. The employer scheduled
employee #1 was at a height of approximately 28 feet when a scaffold rotated. He fell to the ground and was killed.
employee #1 was assigned by his supervisor to a concrete pouring team. As he was directing rubber discharge, the hose was s
employee #1, a carpenter foreman, was working with a rough terrain forklift operator to move construction materials. He stoppe
employee #1 was hooking a winch from a dozer to a pipe stringing truck for a pipeline construction job. While he was between
employee #1 was operating an industrial tractor pulling a pan scraper. When he started down a sloped ditch, the tractor turned
employee #1 employed as a pipefitter on this construction site was working as the immediate vicinity of a 75 grove rubber tree c
iron workers were erecting a pre-engineered steel building structure and had completed 95 percent of the three bay structure w
employee #1 fell through a skylight while resting on it. He died.
at approximately 10:00 a.m. on november 27, 1990, employee #1 was guiding a concrete form by hand as it was being raised b
an employee was dumping dirt under a 13-kilovolt overhead power line. The bed of his dump truck contacted the power line, an
employee #1 connected a supplied air breathing hood line to a plant nitrogen line and then donned the hood to start sandblastin
employee #1, a construction superintendent, age 54, was killed when he was struck by a portable cement mixer which had gott
employee #1 was working on top of a 100 ft water tower that was being demolished. He tied himself to an 11 ft metal ladder tha
employees #1 and #2, the owner of a house moving company and his employee, were working beneath a two-story wood frame
employees #1 and #2, the owner of a house moving company and his employee, were working beneath a two-story wood frame
at 10:10 a.m. on january 17, 1990, employee #1 was installing glass panels on the south wall of the intensified agriculture struc
at approximately 10:53 a.m. on january 21, 1991, employees #1 and #2 were drilling a caisson for a highway bridge when the c
at approximately 10:53 a.m. on january 21, 1991, employees #1 and #2 were drilling a caisson for a highway bridge when the c
at approximately 10:53 a.m. on january 21, 1991, employees #1 and #2 were drilling a caisson for a highway bridge when the c
at approximately 10:53 a.m. on january 21, 1991, employees #1 and #2 were drilling a caisson for a highway bridge when the c
employee #1, a crane operator, and employee #2 were folding a concrete form for shipment when the bolt connected to the lifti
employee #1, a crane operator, and employee #2 were folding a concrete form for shipment when the bolt connected to the lifti
two painters were working at a motel. A 7200-volt overhead power line was located 7.9 meters above the ground and about 3 m
two painters were working at a motel. A 7200-volt overhead power line was located 7.9 meters above the ground and about 3 m
a carpenter was installing a shadow box that was constructed of wood with a metal frame. While he was installing the wooden b
at 9:00 a.m. on july 22, 1997, employee #1, a carpenter, and a coworker were at the south side of a house under construction,
employee #1 was at a construction site when he fell from an open-sided floor, striking the back of his head. He suffered a conc
an electrician was installing an electric sensor for a lighting fixture mounted on a roof. He apparently contacted energized parts
employee #1 was climbing a ladder to dismantle a wood scaffold. As he tried to remove a wood pole with a bar, the pole moved
an employee was working on the roof of a three-story building that was 24 feet in height. The employee threw down a 20-foot-lo
employee #1 was installing tv in penielas, pr. While he was installing a strand of cable he was struck by a strand that had been
four employees were hoisting electrical wire to the top of an electrical pole using two pulleys, a rope, and a motor vehicle. The p
four employees were hoisting electrical wire to the top of an electrical pole using two pulleys, a rope, and a motor vehicle. The p
an electrician was working on a 120-volt branch circuit to a wall outlet. The circuit was energized while he was working on it. To
employee #1 was removing a wood center from the 12 ft ceiling of a house under construction using a 6 ft stepladder. The step
mientras instalaban una tuberia sanitaria dentro de
at approximately 8:10 a.m. on august 9, 1990, employee #1, who was installing roof tile on an office building, fell 8 ft from a lad
at approximately 10:20 a.m. on april 13, 1993, employee #1 was installing a 24 in. diameter pipe line in a trench that measured
an employee was working on an energized electric circuit. He contacted an energized part in a junction box and was electrocute
employee #1 was moving earth with a d-8 bulldozer when the equipment fell 300 ft because the ground was unstable. Employe
employee #1 was removing zinc sheets from the east side of the roof at the warehouse 105 building when he slipped and fell 2
employee #1 entered a manhole and was overcome, falling to the floor. Employee #2 saw his partner fall and entered the manh
employee #1 entered a manhole and was overcome, falling to the floor. Employee #2 saw his partner fall and entered the manh
employee #1 was painting and had climbed approximately 15 feet up a ladder. Suddenly employee #1 lost his balance and fell o
employee #1 and coworkers were picking up garbage bags along the side of the service road of west shore expressway. A tras


                                                     Page 38
                                                        all


at approximately 8:32 a.m. on june 4, 1991, employee #1 was cutting grass near a billboard that was held up by several large I
on december 20, 1993, employee #1 walked across a skylight area where the decking was not able to support his body weight.
an employee was working from a genie lift painting frame work with a paint brush. The employee was electrocuted. (The osha 1
at approximately 2 pm on september 12, 1991, employee #1 was operating a ford #370 rubber-tired roller, driving to a new job
employee #1 was near a turning bar in the end of a rail. The backhoe operator took the bucket and turned the rail. The turning b
two employees were laying a sewer line in a trench when it caved in, killing employee #1. The other employee escaped without
on april 4, 1991 3 workers fell when a pre-cast concrete floor t apparently slipped from the shearwall harness falling and destro
on april 4, 1991 3 workers fell when a pre-cast concrete floor t apparently slipped from the shearwall harness falling and destro
on april 4, 1991 3 workers fell when a pre-cast concrete floor t apparently slipped from the shearwall harness falling and destro
at approximately 2:15 p.m. on may 31, 1991, employees #1 and #2 were working from an elevated scaffold platform and deck a
at approximately 2:15 p.m. on may 31, 1991, employees #1 and #2 were working from an elevated scaffold platform and deck a
at approximately 8:00 a.m. on july 9, 1992, the foreman was operating a case 1845 skid steer loader on a hill with an approxima
employee #1 and coworkers were constructing a driveway. One coworker was operating a bulldozer while employee #1 was be
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
a three story wood frame apartment building collapsed in 46+ mph winds bringing the top story down to ground level. A total of
employee #1 was hanging 8 in. diameter ductwork for a mechanical contractor at a school construction site. He was standing o
at approximately 3:00 a.m. on august 11, 1992, employee #1 was working as a flagman on the highway for hardrives, inc. he w
employee #1 and his employer were walking behind a pole truck directing the truck as it backed up to a new location. Employee
on december 7, 1990, employees #1 through #3 were working on a needle beam scaffold during construction of a feed building
on december 7, 1990, employees #1 through #3 were working on a needle beam scaffold during construction of a feed building
on december 7, 1990, employees #1 through #3 were working on a needle beam scaffold during construction of a feed building
on july 27, 1990, employee #1 was placing corrugated tile in the bottom of a trench that was 6 feet deep, 2 1/2 to 3 feet wide ac
on september 27, 1990, employee #1 was operating a komatsu model 300 backhoe to load sand onto mack semi-tractor belly-
at approximately 7:17 a.m., employee #1 climbed the spiral staircase of a water tower 130 ft to the balcony or catwalk. He was
at 9:20 a.m. on may 1, 1992, employee #1 was cutting shingles while on a 4:12 pitched roof that measured 12 ft from the groun
a helper was assisting a journeyman electrician working at a residence. The project on which they were working involved an ad
employee #1, a carpenter, and a coworker were framing dormers on the 5:12 pitch roof of a residential building. Employee #1 c
several employees were performing maintenance work on a dust collector for an asphalt plant. They were 38 ft 1 9/16 in. high,
employee #1 was preparing to roll insulation over the top beams of a steel roof before installing metal sheeting. He was walking
at approximately 9:00 a.m. on september 4, 1992, employee #1 and two coworkers were attempting to lift a stud wall measurin
employee #1 entered a 24 in. natural gas pipeline to check a weld he had made from the outside on two pieces of metal pipe. H
employee #1 was standing on a 2 in. by 12 in. by 12 ft long plank located 92 ft above the adjacent level, sandblasting the belly o
an employee was operating a backhoe to remove soil from under a house. Employees #1 and #2 dug an excavation under the
an employee was operating a backhoe to remove soil from under a house. Employees #1 and #2 dug an excavation under the
employee #1 was using a homemade bar to clean out the self-unloading belt on an asphalt truck. The bar caught in the web be
two employees were taking sand from a pile in the yard of a house and putting it in the basement to form a base for a concrete
at approximately 8:30 a.m. on october 9, 1991, employee #1 was clearing a creek bed of silt and other debris with a 1982 john
on july 24, 1998, at 7:45 am, employee #1 was working at the roadway and stepped into the patch of an oncoming vehicle. Emp
at 12:40 p.m. on september 16, 1992, employee #1 was attempting to direct a dump body truck into position so it could dump a
two electricians were rewiring a 208-volt square d main distribution switchboard. One employee crawled inside the cubicle to fe
employees #1, #2, and #3 were erecting a long span roof joist while standing on top of the joist. While the wire rope cable sling
employees #1, #2, and #3 were erecting a long span roof joist while standing on top of the joist. While the wire rope cable sling
employees #1, #2, and #3 were erecting a long span roof joist while standing on top of the joist. While the wire rope cable sling
employee #1 was working on a steel erection 23 feet above the ground. He was instructed by the iron working foreman to go to


                                                     Page 39
                                                         all


an employee was working on a roof-top air conditioning unit. He was not using rubber insulating equipment or insulating tools. H
employee #1 was run over and killed by a reversing dump truck. The back-up alarm was not operational immediately after the a
at approximately 12:45 p.m. on october 12, 1992, employee #1, a 49-year-old crane operator, and his helper were disassemblin
employee #1 was handling a suspended load of floor decking that was being set on top of the truss work on the 23rd floor. As h
at approximately 8:00 a.m. on march 7, 1991, employee #1 and a coworker were preparing to clean the pit of an elevator shaft
two employees were using a grove truck crane to move an l-shaped metal platform (approximately 6 feet by 6 feet) to another l
two employees were using a grove truck crane to move an l-shaped metal platform (approximately 6 feet by 6 feet) to another l
at 8:00 a.m. on or about august 21, 1991, employee #1 was boxing a ceiling. When the drywall work was complete, he started t
employee #1 was constructing a brick wall on the outside of a previously constructed block wall when a sudden gust of wind ble
at approximately 3:55 p.m. on september 17, 1990, employee #1 was preparing to service and/or repair the bearings on a 1973
employee #1 was standing along a 12 in. wide painter's platform at the very top of a 6 1/2 story stairwell. The planking was sup
employees #1 and #2 were removing temporary lane striping tape from a completed road project. The employees were working
employees #1 and #2 were removing temporary lane striping tape from a completed road project. The employees were working
employees #1 and #2 were working from a two point suspension scaffold approximately 25 to 30 ft above the sidewalk. The sca
employees #1 and #2 were working from a two point suspension scaffold approximately 25 to 30 ft above the sidewalk. The sca
employees #1 and #2 were working from a two point suspension scaffold approximately 25 to 30 ft above the sidewalk. The sca
at approximately 11:00 a.m. on november 13, 1990, employee #1 was repairing the roof of carlson plywood. He started on the n
an employee was servicing an air conditioning unit that was reported to have been blowing warm air. The employee left the 240
a power line worker had finished installing a cutout switch on a utility pole. After he climbed down, he saw a piece of tape on the
employee #1 was disassembling a radio tower when it fell over. He fell to the ground and was killed.
some public works employees were installing a new water main in a trench that was more than 5 feet deep. The boom on a kom
at approximately 1:00 p.m. on november 17, 1992, employees #1, #2, #3 and #4 were preparing to make an unscheduled repa
at approximately 1:00 p.m. on november 17, 1992, employees #1, #2, #3 and #4 were preparing to make an unscheduled repa
at approximately 1:00 p.m. on november 17, 1992, employees #1, #2, #3 and #4 were preparing to make an unscheduled repa
at approximately 1:00 p.m. on november 17, 1992, employees #1, #2, #3 and #4 were preparing to make an unscheduled repa
employee #1 and other e. lyme highway department employees were resurfacing a road by "chip setting," which involves sprayi
employee #1, a 44-year-old employee of america's finest roofing co., was 11 ft 3 in. above the ground installing concrete tile roo
employee #1 was observed transporting a load of sand in a department of transportation dump truck. The truck veered off the r
ee was working on roof 30' high ee was handling tar bucket fell through skylight
on 7-17-91 at approx 8am ee#1 job foreman deceased was apparently walking in the street leading towards where the ees wer
at approximately 2:30 p.m. on may 3, 1993, eight employees from sonny's roofing company were removing the roof decking fro
at approximately 2:30 p.m. on may 3, 1993, eight employees from sonny's roofing company were removing the roof decking fro
zgnacio v vasquez was ran over by motor grader, while uncovering blue top stakes in the rear of grader.
employee #1, a sandblaster and painter, died in a fall.
employee #1 was standing on a scaffold plank, 65 feet above ground level, inside a newly constructed vessel. He was getting a
employee #1 was doing prep work prior to painting in a second story bedroom of a home. Employee #1 had been instructed an
employee #1 was pulling panels from bracing while on a ladder 10 ft above the ground. The panels were unsecured and fell on
acting on his own initiative, an electrician started stripping insulation from a 277-volt conductor before the circuit was deenergiz
at approximately 3:00 p.m. on july 14, 1993, employees #1 and #2 were working on the roof of a building addition that measure
at approximately 3:00 p.m. on july 14, 1993, employees #1 and #2 were working on the roof of a building addition that measure
an employee was working from a scaffold, laying brick. He brought the metal level he was using too close to an overhead powe
an employee was electrocuted. He was not found until the day following the accident. Apparently, he either contacted a 2300-vo
on or about january 8,1991 at approx 12:50pm a crew of o men were decking the roof of a 40'x 60' storage building peak 18' 9"
at approximately 8:00 a.m. on august 31, 1992, employee #1 and a coworker prepared to install eave trim along a 220 ft by 65
at approximately 11:00 p.m. on or about july 14, 1992, employee #1, wearing a reflective vest, was setting out construction war
employee #1, while walking around a wide piece of equipment, fell about 30 ft to the ground from the unguarded edge of a bridg
a painter contacted an overhead power line. (The original form did not describe what caused the contact.) the employee was el
on march 22, 1991, employee #1, a 23-year-old boilermaker, was opening the tower in the gas plant when the manway was rem
an apprentice electrician and his supervisor were installing wall receptacles in newly built partitions in an office. The apprentice
employee #1 was making joints on the side of a bridge. Because his safety belt was on but not tied off, the employee fell 80 ft to
employee #1 was doing repair work on a cooling tower underground. He fell approximately 35 ft through a 6 ft opening into the
employee #1 was working on a highway project putting down reflectors. Employee #1 was on the running board of a company t


                                                      Page 40
                                                         all


employee #1 was driving a water/fuel truck to a construction site. In turning a corner, the truck rolled over, crushing and killing t
the deceased was working from a 2 tier scoffold on top of on elevator car in a 3 car bank. The crew was spraying insulation on
an apprentice electrician was connecting 277-volt ceiling lighting fixtures on the second floor of a school. He was standing on a
one member of a concrete pouring crew was using a bull float to smooth the surface of freshly poured concrete. The bull float h
employee #1 allegedly fell approximately 12 feet from the roof of a one story building onto a scaffold coupler pin approximately
employee #1 was dismantling a scaffold and fell approximately 30 ft onto a concrete mat at ground level. He died as a result of
employee #1 fell through a fiberglass-covered skylight to the concrete floor 15 feet below.
employee #1 was operating an earth compactor on a decline and got too close to the ramp edge. The compactor rolled over, cr
at approximately 10:00 p.m. on february 3, 1994, employees #1, #2, and #3 were conducting maintenance activities in the gerb
at approximately 10:00 p.m. on february 3, 1994, employees #1, #2, and #3 were conducting maintenance activities in the gerb
at approximately 10:00 p.m. on february 3, 1994, employees #1, #2, and #3 were conducting maintenance activities in the gerb
at approximately 10:00 a.m. on january 13, 1994, employees of austin industrial (ai) were helping mobil mining operations purg
on march 23, 1994, employee #1 was using a vibratory compactor to compress dirt after completing underground pipe work. Em
on september 15, 1994, a crew of 5 belmont employees were assigned to the n-5 area at rohm and haas; acetone cyanohydrin
employee #1 and a coworker were applying sheetrock finishing from an aerial lift that was elevated approximately 11 ft from the
on or about 05/16/97 employee #1 and his helper were painting odd jobs for the homeowner located at 1723 oleander, dickinso
on may 13,1999 at approximately 10:00am, employee #1 was standing on the roof of a building wtching a co-worker replace a
On May 05,2000, at approximately 5:30pm, employee #1 was riding on a traffic control trailer. The trailer was a low-by trailer wh
an employee was working inside an asbestos containment area. He apparently contacted an energized circuit part and was ele
employee #1 was killed when a conveyor fell and struck him.
On March 13,2000 at approximately 8:20am, employee #1 was in the process of digging post holes to install a security fence on
On June 19,2000 at approximately 3:00 pm employee #1 was cleaning up trash in a ditch in preparation to cut grass in that are
On July 1, 2000 at approximately 2:10 p.m., employee #1 was in an open trench approximately 7-8 feet in depth, 2 feet 10 inch
On September 12, 2000 at approximately 11:45 a.m. Employee #1 was on the third floor of a town home under new constructio
On August 28, 2000 at approximately 10:40 a.m. employee #1 was working on roof area of building approximately 92' high. Em
On October 14, 2000, at approximately 3:00 p.m., Employee #1 was using a cutting torch to cut a section from a vertical steel b
On December 8, 2000, at approximately 5:00 pm, Employee #1 was struck by a 1"x8'x20' steel plate weighing in excess of 6,50
Employee #1 and an apprentice were making alterations to a single family residence that was very old and had 120v. wiring tha
employee #1 was preparing to transport metal scaffold frames (waco, 6 ft 6 in. high) from a stockpile to the work area at the en
employee #1, a truck driver, parked his 10-wheel dump truck, raised the bed, and proceeded to the back of the truck. The tailga
at approximately 7:50 p.m. on august 10, 1992, employee #1 was sitting beside the operator of a 951-c caterpillar front end loa
Victim was observed by another employee sweeping the roof in preparation of putting down shingles on the south side of the ap
On November 2, 2000 at appx. 2PM, the victim was helping the employer to unload a bobcat loader from a low boy trailer. The
flam liquid being heated. Victim smelled vapors, unplugged heater. Spark was created, igniting vapors. Victim admitted to uva b
employee #1 was standing in the kitchen area of a residence under construction, handing plywood up to a coworker on the roof
a pole on a metal pump jack scaffold contacted an overhead power line. An employee touching the scaffold was electrocuted.
on 2/1/90 at about 9;30am the decedent were working on a construction site, when he was struck and run over by a reversing d
this fatal accident occurred when an employee was struck in the head by a chair made from 3" lumber 9'5"x 36" in size. The ch
employee struck by the boom of a floating crane after it collapsed while pulling a piling from the water.
employee struck by the boom of a floating crane after it collapsed while pulling a piling from the water.
employee #1 was struck and killed by a metal access plate that was launched by a pressure vessel.
an employee was removing a metal ladder from the side of a house. The ladder either contacted or came too close to an overh
an employee was hauling dirt from one location to another at a construction site. He backed in at the dumping location and unlo
at approximately 9:40 a.m., on october 13, 1993, employee #1, a laborer, was repainting white marking lines inside a lane enclo
employee #1 was standing on an excavation slope when the ground gave way. He fell in and was covered with dirt. He died.
employee #1 was working in a gas station servicing a tank fill area when a motorist ran him over. Employee #1 died of his injuri
employee #1 moved to work site pier 11 (inside the structure) to survey hole alignment for tendon installation which required him
deceased employee was attempting to load a trencher machine onto a trilers, when apparently he drove the trencher over the s
on 8-30-96, at approximately 10:00 am, an employee was attempting to exit a "spider" work cage to gain access to the pier curb
while helping an employer bring equipment into a fourth floor through an outside mechnical room door, employee fell through th
employees were attempting to re-roof a warehouse building (night shift). As work progressed, laborers would move 10 foot sec
employee #1, a linemen who was installing power lines, descended a 145 ft metal utility power pole without his lifeline. He fell a


                                                      Page 41
                                                         all


using 80 and 100 ton link-belt cranes, the employer was attempting to place a 110 ft long, 108,800 lb concrete beam on top of t
using 80 and 100 ton link-belt cranes, the employer was attempting to place a 110 ft long, 108,800 lb concrete beam on top of t
employee #1 was mowing a right-of-way using a zetor 4-wheel drive, 52-horsepower tractor (model 5245) when his right rear tir
at approximately 9:30 a.m. on august 14, 1992, employee #1 was helping a coworker dismantle a crane boom at the butt sectio
employee #1, along with three other employees, were on top of a building on the 5 inch wide red iron walking area of the roof. T
employee #1, a superintendent, was sent to a job site to observe changes being made on a roadway. While he was watching a
three employees were working on a roof with a 1:12 slope. Roofing insulation that weighed approximately 43 lb was being anch
employee #1 was approximately 65 to 70 feet above the ground climbing up a vertical section of steel column. He started slippi
empoyee was removing a roof deck and after changing locations had started to tie off when he made a error and stepped onto
employee #1, a mason, climbed approximately 14 feet to the top of a scaffold platform to help a laborer unload a concrete block
at approximately 7:45 a.m. on september 15, 1990, employee #1 and three coworkers were finishing the installation of a new n
at approximately 8:30 am, on april 14, 1992, employee #1 and another worker started digging an excavation adjacent to highwa
on may 15, 1992, employee #1 was walking under the caterpillar side boom to place a skid under the 8-inch pipe that was lifted
an employee was working on top of a pole barn that was being built beneath an existing 7200-volt overhead power line. The ba
on march 4,1991 job superintendent directed that cross braces be relocated on toscaffodling unit so that carriage workplatform
at approximately 6:45 p.m. on february 12, 1991, employee #1 was shining a flashlight into a 13 inch sleeve located on the bott
employee #1 was standing on the roof of a bay window on the side of a residence in glenbrook, nv. He was reaching out to pain
a power line worker was replacing a utility pole. In violation of written work rules for live-line work, he was working alone and wa
employee #1 was tearing down an old steam-powered electrical plant. Employee #1 was up on a platform about 30 feet above
employee #1 was working as a flagger at a highway construction site. A motorist failed to heed construction warning signs and
at approximately 11:40 a.m. on november 17, 1993, employee #1 was assisting in the placement of a 5,000 lb bundle of metal
employee #1, the owner and sole employee of a water well drilling company, was placing 700 ft of steel casing that was 8 5/8 in
a painter, working from an extension ladder, had just finished painting the fascia board on the southwest corner of a two-story b
a journeyman electrician with 5 years' experience was instructed by his supervisor to connect fluorescent lighting fixtures in the
employee #1 was found dead in the parking lot of his work place. The coroner's determination was that employee #1 died of me
employee #1 was a carpenter foreman at the job site for framing a bridge structure. He was climbing a bridge shoring in the nor
employee #1 suffered cardiac arrest while working on a road construction machine. He lost his balance and fell over the guardr
a construction laborer was assigned to repair damaged pvc electrical conduit that had been cut during an excavation. One of th
employee #1 was assigned to install light bulbs in a sign. Employee #1 used a truck mounted extensible boom lift. The boom ha
employees #1 and #2, of shear force demolition inc. & steel co., were cutting scrap metal into small sections at kerr-mcgee che
employees #1 and #2 were repairing and replacing handrails and gates on top of brine storage tanks. A tank exploded, killing b
employees #1 and #2 were repairing and replacing handrails and gates on top of brine storage tanks. A tank exploded, killing b
an employee was cutting a metal conduit. The employee did not know that it was an electrical conduit containing energized con
a power line worker was raising a no. 4/0 awg triplex cable. About 2 feet above where the triplex was fastened to a utility pole, i
an employee was using a sears craftsman 2-horsepower air compressor to apply texture to a wall in a house. The compressor
employees #1 and #2 were repairing a concrete retaining wall around a city lake. Employee #2 was operating a pettibone hydra
employees #1 and #2 were repairing a concrete retaining wall around a city lake. Employee #2 was operating a pettibone hydra
at or around 2:30 p.m. on december 13, 1994, employee #1 positioned himself on a steel i-beam approximately 32 feet 6 inche
employee #1 was stacking used railroad bridge timber (4 in. by 6 in. by 12 to 13 ft) containing nails and spikes. The nails had be
at approximately 3:30 p.m. on february 3, 1994, employee #1 and the foreman of luckinbill, inc., were laying 8 in. diameter sewe
at approximately 8:30 a.m. on february 26, 1993, employee #1 was hanging ceiling tiles while standing on a 6 ft high mobile sca
on april 9, 1993, the foreman for aduddell roofing and sheetmetal, inc. fabricated an attachment device to mount an economy a
at approximately 8:15 [sic] on august 12, 1996, employee #1, an equipment operator, was attempting to clear a clogged hopper
employee #1 was removing part of a roof. After a portion of the roof had been taken off, he stepped onto the sheet metal and w
at approximately 3:20 p.m. on november 1, 1996, employee #1 was at the apex of the skeletal steel portion of a building under
employee #1 was working on the second floor of a house, protected only by a top guardrail; the midrail was missing. He either t
on 1/20/97 at approximately 9:30 a.m. a worker directed the crane operator to position the hydraulic boom adjacent to 13,000 v
on 1/20/97 at approximately 9:30 a.m. a worker directed the crane operator to position the hydraulic boom adjacent to 13,000 v
employee operating a front end loader when its wheels left the dirt road/pathway and machine rolled down a steep embankmen
an employee was descending down the communication tower via the load line, when he came loose from the line and fell appro
an employee (an ironworker) was electrocuted when he touched a steel I beam that was being moved by a p & h hydraulic truc
employees were preparing to asphalt a residential driveway. A five ton international dump truck was parked in the driveway abo


                                                      Page 42
                                                        all


employee was in a bucket truck. He was moving bucket. Something contacted the line. (don't know what). No one on site with h
employee was laying 8' pvc-r35 pipe when the unprotected trench collapsed on the employee. The employee was struck by the
an employee who was properly trained and equipped for fall protection while working 100 feet above the ground for some unkn
employee was working on a lighting circuit when he was electrocuted with 277 volts. Employee failed to deenergize the 277 vol
employee fell from an elevation
A foreman fell approximately 35 feet from a roof to the ground below. This foreman was assigned to this job for one day (inbetw
at approximately 9:45 a.m. on june 17, 1996, employee #1 arrived at a site with a jlg 1500 jbt boom truck crane. He was plannin
an employee was working from a tubular frame scaffold, 9.1 meters (30 feet) above the ground. As he was moving wooden pla
employee #1 and coworkers were sealing cracks in the roadway. A tractor trailer drove approximately 3 feet into a closed lane,
employee #1 was working at the ground floor level, preparing a house for demolition, when a wall between [the] houses collaps
employee #1 was demolishing a suspended plaster ceiling, above which was a massive section of hvac ductwork. He was direc
at approximately 8:15 a.m. on september 28, 1995, employees #1 and #2 were cutting the east span of an outside gantry crane
at approximately 8:15 a.m. on september 28, 1995, employees #1 and #2 were cutting the east span of an outside gantry crane
a telephone line worker was pulling a telephone cable through a heavily wooded area. A storm the previous night had knocked
at approximately 2:09 p.m. on april 8, 1994, employee #1 was working aloft in an aerial lift bucket, attempting to put the boom b
employee #1 was installing window casing while standing on a scaffold that was approximately 6 ft above the floor. He fell throu
on october 29, 1993, employee #1 was working within the swing radius of a barge-mounted crane used in dredging operations.
employee #1 was on a tank barge while a crane operator was preparing to hoist a 55 gallon drum of waste oil from the barge w
employee #1 was on a tank barge while a crane operator was preparing to hoist a 55 gallon drum of waste oil from the barge w
employee #1 was working in the basket of a 42 foot high condor manlift that was chained to a flatbed trailer. When he rotated th
employee #1 was preparing footer ditches in an unshored and unsloped excavation measuring 100 ft by 125 ft by 8 ft. A portion
employees #1 through #9 were working on a large-scale fire restoration operation at a food processing facility. Employees #1, #
employees #1 through #9 were working on a large-scale fire restoration operation at a food processing facility. Employees #1, #
employees #1 through #9 were working on a large-scale fire restoration operation at a food processing facility. Employees #1, #
employees #1 through #9 were working on a large-scale fire restoration operation at a food processing facility. Employees #1, #
employees #1 through #9 were working on a large-scale fire restoration operation at a food processing facility. Employees #1, #
employee #1 was transporting lumber on a bridge when he fell through an opening between the existing street and a new supp
at approximately 1:10 p.m. on march 12, 1993, employee #1 was in a trench, attempting to complete the replacement installatio
on april 22, 1994, employee #1, a hoist operator at the atlanta detention center construction site, had been on the job approxim
at approximately 9:30 a.m. on june 2, 1993, employee #1 was working from a form scaffold. The employee was wearing a safe
at approximately 11:30 a.m. on december 10, 1992, employee #1 told a truck driver to back up his truck so the sections of his t
employee #1, a self-employed subcontractor with no employees, was using a ladder jack scaffold to install aluminum siding on
employee #1 was cutting metal decking that covered a clarifier tank at a waste treatment plant. The tank contained 14 ft of wate
employee #1, a carpenter's helper, was attempting to free a stuck auger from a guide by using a pry bar. When the auger was f
at approximately 3:30 p.m. on july 2, 1993, employee #1 entered a forest city water tank while a coworker conducted spray prim
employee #1 was part of a crew that was clearing land for a sewer line. The top of a tree being bumped by a track loader snapp
at approximately 10:45 a.m. on march 22, 1990, employee #1 was backing a case 584d forklift, serial #9071997, down an inclin
two painters were positioning a 24-foot-long metal extension ladder against the southeast corner of a building. A 13.2-kilovolt o
two painters were positioning a 24-foot-long metal extension ladder against the southeast corner of a building. A 13.2-kilovolt o
at approximately 12:01 p.m. on july 30, 1992, employee #1 was on a pallet on the forks of a powered industrial truck. He was to
on march 11, 1992, employee #1 was working on the roof of a building 46 ft high. He was moving approximately 4 to 5 sheets o
an eyebolt/sleeve assembly had been incorrectly installed. This assembly was being used to hoist personnel and equipment for
an eyebolt/sleeve assembly had been incorrectly installed. This assembly was being used to hoist personnel and equipment for
employee #1 and six coworkers were attempting to set up a 35 ft long 2 by 6 wooden frame wall by hand. When they had push
employee #1 was standing on an 11 ft 4 in. high by 32 in. wide roof that had a 1:1 pitch. He fell to the ground and was killed.
employee #1 was operating earthmoving equipment in an excavation near an unsupported foundation wall. The wall collapsed,
at the end of a workday, two employees were storing their roofing equipment. A 27-foot, 4-inch-long aluminum roofing hoist was
at the end of a workday, two employees were storing their roofing equipment. A 27-foot, 4-inch-long aluminum roofing hoist was
employee #1 was conducting a framing inspection on a single family residence under construction. He was found in the basem
The victim was working on top of a texaco service station canopy with the owner of r. becker electric, installing wiring and light
three employees were loading a skid steer loader ontol a trailer with a crane. Two employees were guiding the loader by hand w
three employees were loading a skid steer loader ontol a trailer with a crane. Two employees were guiding the loader by hand w


                                                     Page 43
                                                           all


a plastic tarp was placed over a portion of a portion of a condominm unit roof, where rooging material has been removed, to pro
employee accessed scaffold at the beginning of the shift. As he walked to his work area, the plank on which he stood displaced
an electrician was working at a beauty shop, installing a lug for a grounding conductor at the base of a 120-volt panelboard. The
at approximately 9:30 a.m. on may 9, 1990, employee #1, age 29, was working at the 18th floor level on a personnel/material h
employee #1 was walking down a wooden ramp when he fell and injured his knee. He died on may 14, 1994, as a result of his i
employee #1 was installing hydraulic fluid in a dump-body vehicle. Placing himself between the truck's frame and the raised bod
at approximately 1:45 p.m. on november 6, 1995, employee #1 was installing a ventilation system on a roof. He stepped on a la
employee #1 and two coworkers were laying insulation and metal roofing sheets across an 80 ft wide by 200 ft long building. W
at approximately 10:00 a.m. on january 31, 1994, employee #1 was involved in structural steel erection and metal decking insta
employee #1, the sole owner of a small plumbing subcontractor business, was attempting to move a crated water boiler into the
company had established a central breathing air station to supply air line respirators in three locations in the plant. Outside cont
employee wa working in a manhole located at the approach driveway to the gas pumps and gas station & auto repair shop. Two
on january 4, 1990 a painting contractor who had subcontracted to paint a house was killed when he fell about 25' from a ladde
while operating a pedal from outside the operator's cab, employee #1 was crushed to death between the crossarm and the fron
employee #1, an equipment operator for thomas dicenzo, inc., was working at a landfill site and had a ten wheeler truck driver r
employee #1 walked behind a 1988 ford 14 yard dump truck while it was in reverse. Because of his inattention, employee #1 wa
employee #1, an experienced sheet metal worker, was one of four workers removing and installing new sheet metal on the 1.35
employee #1 was standing on top of a load of structural steel on a flatbed trailer. When the employer tried to move an i-beam w
employee #1 lay under an all terrain forklift to jump-start it. With the lift in gear and the accelerator wedged in the full throttle po
employee #1 was assigned to install hangers for duct work in the basement of a building under construction. The employee suf
laborers were returning to the company yard at 3:15 p.m. from a construction site. Three employees of v.f. capaldi were riding i
an employer and one of his employees were taking down a 50-foot-long aluminum ladder. The ladder contacted an overhead p
an employer and one of his employees were taking down a 50-foot-long aluminum ladder. The ladder contacted an overhead p
at approximately 4:00 p.m. on july 9, 1994, employee #1 fell 30 to 36 ft from a roof when a roof bracket gave way. He was killed
an employee was working from a scaffold, operating a power washing machine. The tip of the wand of the machine contacted a
on march 24, 1995, employee #1 was working alone on a tubular welded frame scaffold. He was the mason tender on the build
employee #1 was using a komatsu hydraulic excavator with a shear attachment to demolish a building. He was in the cab of the
at approximately 10:15 a.m. on february 6, 1991, employee #1 and a coworker were standing approximately 16 ft above the pa
two employees were removing an aluminum ladder to secure it at the end of a workday. One employee was on the ground, and
employee #1, the owner, and one of his employees were preparing concrete forms at the bottom of an excavation. The side of
employee #1 was working 30 ft high up a ladder removing a rain gutter. He was hit by the falling gutter and fell to the concrete.
two employees were erecting an aluminum pump jack scaffold. They were erecting it next to a house and beneath an overhead
two employees were erecting an aluminum pump jack scaffold. They were erecting it next to a house and beneath an overhead
two employees were handling an aluminum ladder when it contacted an overhead power line. One of the employees was electr
two employees were handling an aluminum ladder when it contacted an overhead power line. One of the employees was electr
a power line worker with 20 year's experience was working from an aerial lift on an overhead power line. He had removed an 41
at approximately 2:45 p.m. on may 10, 1991, employee #1 was working on a needle beam scaffold that was hung underneath t
employee #1 and three coworkers were working on a work platform 74 ft above the ground. They were operating four 100 ton h
at approximately 8:00 a.m. on february 13, 1991, employee #1 was working alone in a garage. When the owner of the company
at approximately 10:15 a.m. on july 12, 1991, employees #1 and #2 and a coworker were doing roofing work from a pump jack
at approximately 10:15 a.m. on july 12, 1991, employees #1 and #2 and a coworker were doing roofing work from a pump jack
employee #1, a truck driver, set the trolley brake and left his truck in order to decide where to dump its load of gravel. The trolle
employees #1 and #2, who were employed by different firms, were standing inside a building under construction, when the trus
employees #1 and #2, who were employed by different firms, were standing inside a building under construction, when the trus
a trench box and steel plates were being used as shoring in an excavation. A sidewall of the excavation collapsed, causing a st
employee #1 was in the attic of a house cutting and passing precut plywood to two coworkers who were on the roof. The emplo
at 1:55 p.m., employee #1 and three coworkers were working from a steep 12:12 pitch roof with a ground-to-eave height of 20 f
a 77 year old retiree was working on a roof with his son removing old shingles. The father suddenly slid off the roof and fell 11 f
on november 28, 1993, employee #1, the captain of the tug boat "hoosier state", had been assigned to stand by and assist the
on november 28, 1993, employee #1, the captain of the tug boat "hoosier state", had been assigned to stand by and assist the
employee #1 rode a single point scaffold buggy and accompanying two-point scaffold to the top of a 100 foot water tower. He w
an employee was using a lincoln ac/dc, constant-current electric arc welder (model no. Ac/dc 225/125). The switch on the weld


                                                       Page 44
                                                        all


at approximately 2:45 p.m. on august 26, 1994, employee #1 stopped work to buy a quart of oil from the store across the street
employee #1 had finished assisting two carpenters on the deck of a garage that was under construction. While stepping onto th
employee fell from roof.
at approximately 10:00 a.m. on february 21, 1992, employee #1 was working alone cleaning out the dump body of his truck. Wh
at approximately 4:30 p.m. on june 14, 1992, employee #1 was squatting on the slope of a roof as he painted the fascia board o
employee #1 was assigned to form a parapet wall in preparation for a pour. He tripped or slipped on debris and fell 282 ft down
at approximately 8:15 a.m. on october 1, 1991, employee #1 was laying sheets of insulation on a 90 ft square flat roof adjacent
worker #1 was in the process of clearing small saplings from around guy wires supporting electric power transmission systems.
at 5:30 p.m. on may 17, 1990, employee #1 was rigging steel that was to be installed on the roof of a structure for a track to be
employee #1 was standing on the left side of a flatbed trailer being towed by his dump truck. His truck and trailer were parked b
in preparation to end the workday, an employee used a crane, with four outriggers extended, to hoist a mobile welding machine
employee #1 was working on a glass skylight frame. He was standing on a cementitious roof deck panel, measuring 6 feet by 2
employee #1 was a deckhand on a barge being towed into the shinnecock inlet during rough seas. The barge overturned and e
employee #1 was standing with a coworker on top of a concrete block wall that was 28 feet 8 inches high. There were four joist
victim was working on elevated scissor type truck bed at 13 ft level. He stepped backwards off bed falling to ground. Victim hit h
at approximately 2:35 p.m. on december 8, 1995, controlled blasting operations were being conducted at a construction site to
a power line worker was changing the cutouts on a 7620-volt-to-ground overhead power line. The employee contacted the line
an employee of a subcontrctor was cutting asphalt pavement with an air supplied jack hammer on a road under construction. A
sometime after 2:00 p.m. on october 3, 1991, employee #1 was climbing the ladder of a ladder jack scaffold while carrying a 2 i
an employee was working from a ladder, installing wiring. He contacted an energized conductor, and the electric shock he rece
employee #1 was placing highway cones when an asphalt roller passed by, then reversed direction approximately 10 ft from him
employee #1 was placing highway cones when an asphalt roller passed by, then reversed direction approximately 10 ft from him
Employee was descending ladder and fell approx. 15 ft. to lower level.
at approximately 1:30 p.m. on october 15, 1997, employee #1 was preparing to lay fireproof sheathing on the roof trusses besid
at approximately 8:26 a.m. on february 4, 1997, employee #1 was laying #15 asphalt felt roofing paper on the roof of the pentho
an employee had finished painting the exterior front side of an apartment building. He then carried his 8.5-meter-long (28-foot-l
at approximately 8:15 a.m. on march 11, 1991, employee #1 was about 20 ft up on the western end of a bridge abutment under
employees were preparing to move a light pole. Employee #1 was standing near the base of the light pole. The operator of the
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
at approximately 12:15 p.m. on february 14, 1991, employees #1-10 were working from a morgan scaffold platform, approxima
an employee was welding 1.5-inch-diameter gas feeder pipes from a 4-inch-diameter main. The pipes fed into classrooms of a
on january 14, 1997, employee #1 was a member of a five-person crew that was dismantling a metal building. He was on the e
employee #1 was in an elevator shaft attempting to remove the casing from a drill bit that was being hoisted up, when the sproc
employee #1 was erecting a precast concrete shell at a water treatment plant. The employee had welded one panel to the foun
at approximately 6:45 a.m. on june 14, 1990, employee #1, a tractor equipment operator for warren smith trucking, inc., of flags
at approximately 8:00 p.m. on july 25, 1990, employee #1 was spraying lacquer on ceiling beams in the living room of a house u
employee #1 and a coworker were installing a rigid electrical conduit on the 46 ft level of a structural steel. The conduit was imm
employee #1 was directing a tandem lts-9000 tractor trailer rig (serial #1fdyu9drxca40891) onto the shoulder of a road where ba
at approximately 9:10 a.m. on july 23, 1990, employee #1 was preparing a street for paving by compacting base coarse gravel
at approximately 1:30 p.m. on february 21, 1991, employees #1 and #2 were tunneling under the east side of a slab house to lo
at approximately 1:30 p.m. on february 21, 1991, employees #1 and #2 were tunneling under the east side of a slab house to lo
employee #1 had responded to a routine weekend service call from a local restaurant to unplug a sewer drain. He arrived alone
at approximately 12:00 noon on march 29, 1995, employee #1 was working from staging above a concrete floor. He was attach
employee #1 was working at the top of a ladder on a hot day. He became sick and fell approximately 17 ft. Employee #1 died a


                                                     Page 45
                                                          all


employee #1 was reshingling a 2 story house, while working alone in a rainstorm. The employee somehow lost his balance and
employee #1, the owner/operator of a building repair and remodeling company, was killed in a trench cave-in.
employee #1 was operating a dozer when it turned over and slid down an earth embankment. His head struck against the rollov
employee #1, a 28-year-old roofer, fell 22 ft through a hole in a roof under repair. He sustained a serious head injury and was k
employee #1 was preparing a trailer so a backhoe could be loaded onto the trailer. The employee unchained the ramp from the
employee #1 was 7 ft above the floor on a genie personnel lift. He was installing all-thread and brackets on a 623 banbury line t
on march 7, 1996, employee #1 was on site when structural steel collapsed. He was struck on the head by falling bar joists that
a crew of employees was razing water pumping station houses. The seven houses were small, one-story brick structures, abou
a power line worker was electrocuted, apparently during the installation of a pole-mounted transformer. The employees had not
employee #1 was winding up four reels of wire (conductors) or lead lines when the reel winder tipped over onto him. He was cru
a power line worker was working on a utility pole, stringing new conductors. He contacted a 240/120-volt conductor and was ele
on september 24, 1990, three employees were working on a 5:12 pitched roof that had a 3 ft flat surface around the perimeter,
padding or other protection was not used while lifting material with sharp edges by means of nylon web slings. Employee #1 wa
employee #1 and another employee were told to clean off the excess concrete around a concete pumping system when the po
employee #1 was operating a hydraulic crane that was lifting approximately 2,000 lb of sheet rock to a work station. While being
an electrician was stripping insulation from a 277-volt conductor in preparation for the installation of a lighting fixture. The emplo
four employees were raising a 40-foot-long aluminum ladder. As the employees turned the ladder towards a house, the ladder c
on wednesday, september 12, 1990, employees #1 and #2, laborers, had been assigned to block the windows of a parking gar
on wednesday, september 12, 1990, employees #1 and #2, laborers, had been assigned to block the windows of a parking gar
employee #1, a laborer, was preparing the surface of a newly back-filled trench for placement of a black top patch in a 9 ft wide
an electrical testing technician was making leakage tests in a deenergized substation. The employee removed a panel cover, w
employee #1, a boilerworker (firewatch), was attempting to put out a small fire caused by welding operations. He apparently fell
at approximately 3:00 p.m. on june 11, 1990, employees #1 and #2 were demolishing a three car garage using hand tools. The
at approximately 3:00 p.m. on june 11, 1990, employees #1 and #2 were demolishing a three car garage using hand tools. The
employee #1, a laborer lying on a man-made cart, entered a new water pipe approximately 350 ft long by 36 in. in diameter. He
employee #1 was operating a ford-new holland skid-steer loader, model l-781. He was returning with the bucket in the fully raise
employee #1 was leaning into an elevator hoistway when the elevator car came down and crushed him between the bottom of t
employee #1, an iron worker, was setting roof sheeting 35 feet above ground level when high winds blew him through a roof op
an electrician was working in a prone position in the crawl space of a residence. He contacted an energized conductor and was
employee #1 suffered a heart attack and was taken to the hospital where he died.
at approximately 10:00 a.m. on july 28, 1993, the foreman removed a 24 in. diameter manhole cover and smelled gasoline. He
at approximately 10:00 a.m. on july 28, 1993, the foreman removed a 24 in. diameter manhole cover and smelled gasoline. He
employee #1 was an employee of a construction company that was hired by the township to build a new sewage pump station.
at approximately 10:35 a.m. on september 28, 1993, employees #1, #2, #3, and #4 were on tiered tubular welded frame scaffol
at approximately 10:35 a.m. on september 28, 1993, employees #1, #2, #3, and #4 were on tiered tubular welded frame scaffol
at approximately 10:35 a.m. on september 28, 1993, employees #1, #2, #3, and #4 were on tiered tubular welded frame scaffol
at approximately 10:35 a.m. on september 28, 1993, employees #1, #2, #3, and #4 were on tiered tubular welded frame scaffol
at approximately 7:15 a.m. on september 7, 1993, employee #1, an iron worker, was laying roof joint material while positioned o
employee #1, a dockbuilder pile monk, fell from an unsecured sheet piling. He was killed.
on october 7, 1993, employee #1, employed as an estimator by lowe roofing co., went to a mall at the request of the owners to
an employee was setting up a water well drilling rig. As he raised the boom of the rig, it contacted a 7200-volt overhead power l
employee #1, a co-foreman and roofer for 30 years, was removing built-up roofing from a deteriorated roof. Planks had been pu
employee #1, a roofing foreman, was transporting many combustible and/or flammable materials in a chevy cargo van. The ma
employee #1, an operating engineer, was stowing a removable jib on a boom truck. The locking pin was inserted into the lockin
employee #1 was enlarging an existing hole in the top of a manhole cover when the diamond segmented chain on a maxcut 12
at approximately 3:00 p.m. on september 28, 1992, while performing siding and gutter work from a ladder jack scaffold, employ
at approximately 7:30 a.m. on august 26, 1995, employee #1 was preparing to enlarge a roof opening on a single-story store bu
employee #1 was attempting to remove a catenary scaffold from the underside of a lift bridge that was in the raised position. Em
on september 17, 1996, employee #1, who had been hired as a laborer with a road paving crew, was apparently performing his
at approximately 6:45 p.m. on june 1, 1996, employee #1 and a coworker were working on a construction project at the america
employee #1, an iron worker, was attempting to climb a structural steel column to an i-beam 23 ft 7 in. above the concrete floor
employee #1 was in a trench approximately 30 ft below the surface, installing an 8 in. Pvc pipe in a concrete manhole. A safety


                                                      Page 46
                                                        all


at approximately 3:05 p.m. on november 25, 1991, employees #1 and #2 were placing equipment on a work truck. They were p
at approximately 3:05 p.m. on november 25, 1991, employees #1 and #2 were placing equipment on a work truck. They were p
at approximately 8:25 a.m., on september 8, 1992, two workers were standing on a steel girder during steel erection for a ware
at approximately 9:00 a.m. on september 8, 1992, employee #1 was working on a two-point suspended scaffold. While he was
on september 27, 1990, employee #1 fell approximately 24 ft 6 in. from a ladder while scrubbing the side of a building. He struc
employee #1 was sorting roof purlins in a shakeout area. In his vicinity, employee #2 was operating a grove hydraulic crane, mo
employee #1 was sorting roof purlins in a shakeout area. In his vicinity, employee #2 was operating a grove hydraulic crane, mo
employee #1 and a coworker were in an 8 ft deep by 4 ft wide trench in type c soil with water in the bottom. They were installing
employee #1 was welding antenna mounts (brackets) to the leg of a water tower for use by a cellular phone company in mobile
on june 26, 1994, employee #1, a plumber, was installing a 4-inch pvc sewer pipe for a new lateral hookup for a private residen
an employee was using a ladder to access an elevated working location. He was electrocuted when he contacted an overhead
employee #1 and a coworker were installing an 8 inch sewer line pipe inside a 12 ft deep by 5 ft wide by 60 ft long trench. A 35
employee #1 was painting the west side superstructure of a railroad overpass. He was on his knees with his back to an unguar
while removing a section of a roof, employee #1 was crushed when he apparently ran underneath the falling roofing to get to a
employee #1 was laying pipe in a 5 1/2 ft deep trench. The unshored trench caved in on the employee, burying him. He died.
at approximately 10:40 a.m. on september 12, 1994, employee #1 was working aloft on an exterior roof deck, spray painting be
employee #1 was engaged in grooving operations on a runway at night. He was exposed to vehicle traffic but was not using a r
at approximately 11:45 a.m. on february 11, 1995, employee #1 was walking across a deteriorated section of roofing to go to lu
employee #1 was crushed and cut in half by an ingoing nip point on a pettibone speed swing. The nip point was created by the
employee #1 was riding the forks of a fork truck, balancing the load. The fork truck hit a stump and ejected the employee and th
employee #1 was working approximately 50 ft high on tubular steel, securing loose decking. He noticed that a welding lead that
an employee was working from a scaffold positioned near an overhead power line. A piece of sheet metal he was holding conta
employee #1 had covered a roadway construction sign. He was crossing from the median to the shoulder of the highway's east
at approximately 12:15 p.m. on february 13, employee #1 was removing roof material from a building that was being demolishe
employee #1 was working from a ladder when he suffered a heart attack and died.
employee #1 stepped onto an unsecured piece of metal decking that had been laid across the roof trusses of a building. When
employee #1 was fueling a roller located in the median of an interstate highway that was being reconditioned. He had to cross a
at approximately 9:30 a.m. on december 17, 1993, employee #1 was working on an 18 foot high roof. There was an invisible fro
at approximately 7:00 a.m. on march 20, 1996, employee #1 was attempting to remove an aluminum form for a concrete stoop
employee working on two point suspened scaffold pointing brick without guardrails or being tied off.employee leaned over end o
employee was standing with back to roadway talking with co-worker when he was struck by a backing dump truck. He fell unde
employee #1 was in the basement of a demolished building, using a cutting torch to cut up scrap i-beams. A concrete block wa
employee #1 was in the basement of a demolished building, using a cutting torch to cut up scrap i-beams. A concrete block wa
employee #1 was cutting braces on the catwalk of a conveyor when the catwalk collapsed. Employee #1 fell approximately 30 t
at approximately 11:30 a.m. on march 22, 1991, employee #1 was removing a 12 ft high, 5 ft wide window with a 6 ft spud bar.
employee #1 was working next to an unguarded roof edge that was 19 feet 11 inches above the ground. He fell from the roof o
at approximately 12:45 p.m. on april 9, 1992, employee #1 was handing material off the roof to a coworker in a dormer. The em
an employee entered an electrical cabinet to install mineral wool fireproofing on the floor. The cabinet was energized at the time
employee #1 was standing on a stepladder preparing to use a cutting torch. He lost his balance, fell onto the concrete floor, and
employee #1, a laborer, knelt behind a road grader and was backed over when the machine moved in reverse gear. He was kil
employee #1 was working in a large chimney from a single point suspension scaffold. He was killed when brick debris fell and s
an employee was working in a confined area. Energized circuit parts in the area were not completely guarded, and the employe
employee #1 was installing a safety line for a swing scaffold when he fell 60 ft to his death from a roof.
at approximately 11:30 a.m. on november 23, 1993, employee #1, a foreman, and his work crew were laying sewer line laterals
an employee was working from a scaffold, removing metal wall studs. One of the studs cut into a 120-volt cord that was lying on
at approximately 11:00 a.m. on october 9, 1994, employee #1 was killed when he stepped off a ladder at the edge of a roof and
employee #1 was using a portable 800 watt gasoline-powered generator inside a room that did not have adequate ventilation. T
at approximately 6:00 p.m. on july 25, 1994, employee #1 finished sealing a fill area using a drago vibratory compactor roller an
an employee was holding a truss lifting device supported by a crane. The device was being moved into position to lift a wooden
at approximately 2:20 p.m. on november 9, 1994, employee #1 was cutting down a poplar tree that measured approximately 32
employees #1 and #2, iron workers, were positioning a strut support for welding. They became caught between the work baske
employees #1 and #2, iron workers, were positioning a strut support for welding. They became caught between the work baske


                                                     Page 47
                                                          all


employee #1 was traveling approximately 15 to 20 mph down a one mile hill on a paved road in a 1985 clark rubber-tired front e
a partner in a roofing company was installing metal edging on a roof. The metal edging contacted an overhead power line, and
employee #1 was working 15 ft above the ground from an aerial lift installing electrical wiring in a traffic light. The aerial lift was
an employee was holding onto a wire rope sling attached to the hook on a crane. The sling was gripping a wooden bulkhead th
some employees were using a rough terrain forklift to move a tower scaffold. The scaffold contacted an overhead power line; a
some employees were using a rough terrain forklift to move a tower scaffold. The scaffold contacted an overhead power line; a
employee #1 was part of a crew that was constructing a steel roof on a one story building. He was moving to another part of the
employee #1, the foreman, and three coworkers were working on a cut and cover sewer line installation. Employee #1 was the
employee #1 was exiting a jlg lift onto a roof. He fell approximately 55 ft and was killed.
employee #1 was run over by an earthmoving (hauling) dump truck that was backing up. He was killed.
employee #1 was pulling approximately 7,000 lb of black iron pipe through a tunnel when the wire pulling machine he was using
an electrician was connecting a fluorescent lighting fixture to a 277-volt circuit. (The circuit could have been deenergized, but it
employee #1 and other employees were dismantling a coal hopper and conveyor system that was used to provide coal to boiler
employee #1 was felling a tree. As the tree fell it caught a guidewire to a utility pole equipped with a transformer. The utility pole
on september 5, 1991, employee #1 was putting up vinyl siding from an unguarded open-sided platform constructed of a 24 ft lo
employee #1, a foreman, was 92 ft high in a one-man basket that was attached to the jib extension of a boom. After the operato
employee #1 fell 180 ft during the demolition of a coal conveyor belt system. He was killed.
five employees were watching a tow truck pull a flat bed delivery truck from a ditch. To keep the front of the tow truck from slidin
an employee was carrying aluminum flashing up an aluminum ladder. It was very windy, and the flashing contacted an overhea
employee #1 was on a platform burning off old rivets and installing an additional sheet of plate steel. He was securing it with nu
employee #1 was in a one man spider (spider staging corp., seattle, wa, model st 180). The 5/16 in. cable was not properly atta
employee #1, who was not an employee but was a cousin of the owners, was driving a roller to a gas truck for refueling. He fell
employee #1 was standing on a catwalk cutting a structural member from the support system of the duct work in a bag house.
employee #1 was descending the top ladder on a two-level fixed scaffold. As he was descending the ladder (possibly going from
employee#1 was part of a crew that was erecting a sign on an interstate highway. He was struck and killed by a passing car.
employee #1 was improperly sitting in the cab of a truck crane. When the operator started to lower the boom, the brakes on the
employee #1, a foreman, was in an 8 1/2 ft deep trench to repair a leak in an 8 in. Pvc sewage line. The pipe had been installed
employee #1 was painting when he fell approximately 17 feet from an elevated work platform. He died.
a power line worker was removing one conductor of an overhead power line. He was passing the conductor between two 2400-
employee #1 fell 20 feet from a ladder and struck his head on the ground. He died from his injuries.
an employee was repairing an advertising sign while it was energized. He was working from a kneeling position on wet ground
employee #1 was assigned to locate and open, but not enter, the manhole of an abandoned sewage ejector access pit that had
employee #1 was identifying and marking a roof for the purpose of landing materials when he stepped onto and through an unp
employee #1 was working on an 8:12 pitched roof. Coworkers had just removed old asphalt shingles, which he was throwing to
some employees were unloading a trailer of roofing material. A crane picked up the load, and the operator swung the boom to p
employee #1 fell 60 feet from an open-sided floor during the erection of a butler building. He was killed, suffering a broken neck
on march 21, 1991, employee #1 was standing near a table against which two metal grates were leaning, one on each side. On
employee #1 was riding in the back of a pickup truck, sitting on the side of its bed above the wheel. The truck started and move
on march 2, 1995, a 7 ft deep trench, which was not protected, caved in on employee #1. He died on may 24, 1995.
employee #1 was installing a low-sloped roof (1:12) on a building. The employee fell approximately 27 feet from the roof and di
employee #1 was positioned beneath a section of an unsupported roof area when a slab of rock and debris fell, striking and crit
employee came in contact with 2300 volt electrical sub-station while spray painting.
employee #1 was the operator of a grove rubber-tired crane. The crane was overloaded and when it picked up a slab of concre
employee #1 was on the second floor of a four-story building that his employer had been contracted to tear down. He had burne
employee #1 was killed when he fell 18 feet through a skylight on a flat roof.
employee #1 suffered and died of a heart attack while working.
an employee was electrocuted when the mast of his drilling rig contacted a 7200-volt overhead power line.
an employee climbing up the left side of a scaffold contacted a 2300-volt overhead power line. He was electrocuted. He also fe
employee #1 was demolishing a building in pittsburgh, pa, when the second floor collapsed and pinned him under a beam and
employee #1 fell approximately 26 feet from a sloped roof while preparing to install shingles on a single family house that was u
an employee was setting utility poles for a fiber optic telephone line. While he was setting a pole with a digger derrick, the boom
at approximately 11:00 a.m on september 15, 1994, employee #1 was in an aerial lift basket approximately 21 ft above the grou


                                                       Page 48
                                                         all


employee #1 fell though a hole in the floor and suffered blunt force trauma to the neck. He died.
at approximately 5:45 p.m. on october 25, 1994, employee #1 was unfolding an air net/tarp on an open-sided mezzanine/platfor
employee #1 was using a 10 ft metal stepladder to descend from the 2nd floor to the 1st floor of a house. While getting on the l
employee #1 was crushed and killed by an rd-35 concrete roof beam. The beam failed in flexural [sic] because of the inadequa
employee #1 was riding in the back of a dump truck that turned over, crushing and killing him.
employee #1 was using a cutting torch to cut up scrap i-beams in the basement area of a demolished building. A concrete bloc
employee #1 was using a cutting torch to cut up scrap i-beams in the basement area of a demolished building. A concrete bloc
employee #1, an iron worker, was on a float scaffold approximately 110 ft from the water surface setting in a bilateral corner pla
employee #1 was under a machine repositioning a rigging skate when the machine moved and fell on him. Employee #1 died.
three employees were installing a circuit breaker in switchgear in an underground vault. As the employees were racking in the b
three employees were installing a circuit breaker in switchgear in an underground vault. As the employees were racking in the b
three employees were installing a circuit breaker in switchgear in an underground vault. As the employees were racking in the b
three employees were installing a circuit breaker in switchgear in an underground vault. As the employees were racking in the b
three employees were installing a circuit breaker in switchgear in an underground vault. As the employees were racking in the b
employee #1, the operator of a caterpillar d-7 bulldozer, was traversing a construction road when he veered off the road. Emplo
an electrician was removing a 277-volt, 70-watt sodium lighting fixture. He opened a 102-millimeter-square (4-inch-square) junc
a power line worker was working from a utility pole at a height of about 38 feet above the ground, installing a new line on the po
employee was carrying metal deck pans to another employee who was placing the pans between two pre-stressed beams in a
employee #1 was walking up a construction vehicle ramp when he was struck by a tri-axle dump truck and knocked to the grou
a power line crew was installing wiring in an underground conduit. One of the crewmembers was working near a pad-mounted
employee #1 had attached a chain sling to a 30 to 40 foot steel h piling in order to move it for transport. When the piling was ho
on june 25, 1993, employee #1 and a coworker, carpenters for recchi america, inc., bridge constructors, were instructed by a fo
at about 8:00 a.m. on july 7, 1992, employee #1 and a coworker were working on a residential driveway. They had been instruc
two contracting companies, r & d and hunt, had been hired by gold kist to do construction work. R & d was to install a conveyor
two contracting companies, r & d and hunt, had been hired by gold kist to do construction work. R & d was to install a conveyor
two contracting companies, r & d and hunt, had been hired by gold kist to do construction work. R & d was to install a conveyor
two contracting companies, r & d and hunt, had been hired by gold kist to do construction work. R & d was to install a conveyor
on april 20, 1992, employee #1 was attempting to exit the cab of a bobcat skid steer loader when he was crushed against the ro
on the morning of september 30, 1992, employee #1 was part of a three-man crew that was taking down an aluminum reflector
a three-person power line crew arrived at a worksite in a farm field. Their employer, a power line contractor, had the job of repla
a roofing contractor was removing an old roof and putting on a new metal deck roof on a 200 by 500 foot building for the u. s. n
employee #1, on his second day on the job, was sent to direct trucks and take tickets from truck drivers who had delivered their
at approximately 3:00 p.m. on august 7, 1991, employee #1, of a boring company, entered a 23 1/4 in. diameter steel tube that
at approximately 9:30 a.m. on september 15, 1993, a coworker was operating a crawler crane to hoist and transport an oxygen
according to an eyewitness, employee #1 walked behind a backing dump truck and was knocked to the ground. He tried to avo
employee #1 was setting a roof truss. He had one foot on a truss already erected and temporarily braced while the other foot w
employee #1 was driving a riding mower. He went over the edge of a creek embankment and the mower fell on top of his chest
an employee was connecting a load of trusses to the load line of a crane. The load line was too close to a 7620-volt overhead p
an electrician was working from a 10-foot-high stepladder, installing overhead lighting fixtures in a new department store under
employee #1 was on bridge #2. In crossing from the east side of the bridge to the south side to join two coworkers, he went dire
an employee was lying on his stomach in the crawl space of an attic in a house. He was replacing a blower assembly, reaching
an employee was assigned to connect a ground wire to the neutral conductor of an overhead power line. The employee, who w
the operator of a ford boom truck had positioned his truck under an overhead power line. As he was moving a load of valves on
at approximately 11:45 a.m. on june 29, 1995, employee #1 was inside an area in a power plant boiler room that was restricted
a crew of employees was loading an 8-foot-by-20-foot steel trench box onto the rear of a tractor trailer. They were using a p & h
employee #1, a laborer, was cleaning up on the fifth floor of a condominium under construction. He was using a wheelbarrow to
an employee was working about 14 feet above the ground on a scaffold that had been erected on a stainless steel vessel. The
on april 8, 1992, employee #1 was working 80 ft above the ground and was tied off with a safety belt. Apparently, he released th
the boom on a water well drilling derrick was raised into a 13.5-kilovolt overhead power line. An employee who was standing on
employee #1, a labor foreman, stepped on an unsupported plank on an elevated scaffold platform. The plank, which was part o
employee #1 was working alone on the shingled roof of a house. The roof had a slope of 4:12 and an eave height of approxima
employee #1 was conducting an air conditioning service/repair call on the roof of a home. The employee was working alone an


                                                     Page 49
                                                           all


employee #1 was a paving worker who attempted to jump onto a moving piece of road widening equipment. He slipped and fell
employee #1 had completed service on an elevator door interlock and was still in the elevator pit on a ladder under the elevator
employee #1 was removing a piece of steel reinforcement rod from a bulldozer's left track. He left the engine running and was n
employee #1 was assembling form frames for concrete at the edge of a recently poured concrete floor when he apparently step
employee #1 was working on the construction of a two-story single family residential structure. He descended the wraparound s
employee #1 worked for a company that installs septic tanks. After many days of rain and several attempts to install two septic
a salesman for a repair company was checking a flood-damaged air conditioner that was mounted on the ground outside a resi
at 1:00 p.m., employees #1, #2, and #3 were hand-grading alongside a roadway in preparation for laying sod. The driver of a ca
at 1:00 p.m., employees #1, #2, and #3 were hand-grading alongside a roadway in preparation for laying sod. The driver of a ca
at 1:00 p.m., employees #1, #2, and #3 were hand-grading alongside a roadway in preparation for laying sod. The driver of a ca
at approximately 8:00 a.m. on june 20, 1995, employee #1 was using a lull model 844b highlander forklift to unload metal reinfo
employee #1 went into a pump room to connect an extension cord to a sump pump plug. There were no witnesses to the accid
employee #1 wandered into an area uphill from a site where a coworker was using a hydraulic excavator to clean [sic]. an uproo
employee #1, a carpenter, was working in the rafters on the second floor of a custom-built house that was under construction. H
on april 6, 1996, employee #1 and approximately three coworkers, of a-1 drywall, were installing drywall in a one-story building.
on the evening of november 30, 1995, employee #1 was checking traffic control devices erected in the eastbound lane on state
employee #1 and employee #2 fell from a communication tower. Employee #1 was killed and employee #2 sustained injuries th
employee #1 and employee #2 fell from a communication tower. Employee #1 was killed and employee #2 sustained injuries th
a communications worker was installing a cable television cable on a joint-use utility pole. The employee, who was wearing pole
employee #1, the owner, had climbed an old radio tower to change cables from the old tower to a new one. He fell 300 ft to his
two employees were removing a conduit from a beam that was to be taken out. Two overhead lighting fixtures were supplied by
two employees were placing a guy in position on a new utility pole. One of the employees was on the ground; the other was wo
employee installing a subfacia on a 5 in 12 pitch roof, 30 feet 8 inches above-ground. Employee slipped and fell off the edge of
employee #1 was stripping concrete forms on a stairway between the fourth and fifth floors. He slipped and fell into an adjacent
employee #1 was a member of an eight-man crew that was performing build-up roof work. The employee was standing near th
a crew of laborers was using a crawler crane to lower a 1-cubic-yard bucket of concrete. The crane was operated within 10 feet
a crew of laborers was using a crawler crane to lower a 1-cubic-yard bucket of concrete. The crane was operated within 10 feet
employee #1 was welding an extension onto a 12 inch "h" batter pile. He was standing approximately 30 feet from a vertical 38
employee #1 had called in a service company to check out his john deere 70 excavator. While the field mechanic was checking
employee #1 was unloading a bulldozer from a trailer. As he was backing up, the dozer went off the edge of the trailer. Employe
on february 9, 1990, employee #1, an operator/laborer, was grading the bottom of a 10 ft deep trench of predominantly sandy s
on october 22, 1991, employee #1 was directed to assist a coworker, a backhoe operator, in removing light poles from the park
two employees were delivering a load of roofing shingles to a single family dwelling. They were using a 35-foot portable convey
at or about 11:35 a.m. on november 5, 1993, employee #1 and a coworker on a road construction job were talking to each othe
at approximately 10:45 a.m. on october 27, 1993, three employees were digging and lining up excavations so that sewer pipes
two employees were working from a hi-ranger aerial lift. They were clipping energized lines and installing new (deenergized) lin
two employees were working from a hi-ranger aerial lift. They were clipping energized lines and installing new (deenergized) lin
employee #1 worked for marlon dunn contracting, inc., as a tail man (laborer) on a pipe laying crew. On april 14, 1994, employe
an electric utility called in a power line contractor to repair a line outage that was due to a fallen tree. The contractor's crew arriv
an articulating boom with basket mounted on a fire truck was being tested by the new owner, the president of an electrical cont
on or about february 19, 1993, employee #1 was working from a scaffold platform that was attached to column forms. He remo
an apprentice electrician was assigned the task of installing a fluorescent lighting fixture in a suspended ceiling grid. He was to
an employee was installing a lighting fixture in the dining room of a house. He went to lunch and then returned to work. He stoo
on the morning of december 21, 1995, three employees of amick construction were spreading a sand and clay mixture at the n
on april 13, 1993, employee #1 was setting girders constructed of prestressed concrete for a span of approximately 90 ft on a b
an equipment operator was moving a fallen 64-foot-tall pine tree from a 230-kilovolt overhead power line. As his frankline skidd
at approximately 1:40 p.m. on june 22, 1993, employee #1 was finishing lunch. The company was pouring concrete sidewalks a
employee #1 died. According to the autopsy report received, the cause of death was a heart attack.
to remove a part, a front loader was used to lift the rear door of a shredder. Employee #1 got off the loader and stood beneath t
employee #1 was dismantling a telephone company tower that was 150 ft high. At the 90 ft level, he loosened the bolts on the e
employees were removing the existing roof shingles of a two-story single family house for replacement. Employee #1 was assig
employee #1 was throwing concrete blocks from a 4th floor edge when he fell 27 feet to a steel truck bed. He died from his inju


                                                       Page 50
                                                          all


on the morning of september 8, 1993, employee #1 was assigned to finish off a masonry structure that was within 12 feet of an
employee #1 was just inside a circular concrete septic tank that had been lifted out of the ground and laid on its side. He was re
at approximately 12:20 p.m. on may 20, 1991, employee #1 and two other employees were cleaning a melt piping reboiler with
an employee (employee #3) was using water at high pressure to clean structural steel close to the ceiling in a paper mill room.
an employee (employee #3) was using water at high pressure to clean structural steel close to the ceiling in a paper mill room.
an employee (employee #3) was using water at high pressure to clean structural steel close to the ceiling in a paper mill room.
employee #1 and two coworkers, who worked for an industrial contracting company, were replacing an old roof with a new one.
an electrician was electrocuted as he worked on a switch box.
on january 18, 1994, while removing roof sheets, employee #1 fell 14 feet through the roof to the concrete ground. Employee #1
maintenance employees were greasing fittings on a front end loader. One worker was at the operator's cab. Employee #1 was
at approximately 11:30 on may 2, 1994, employee #1 was installing an 8-in. sanitary sewer line in a trench that was approximat
two power line workers were working on an overhead power line. One of them was in the bucket of an aerial lift, and the other w
employee #1 and a coworker were using water and brushes to clean a sloped metal roof. Employee #1 was working near the b
employee #1 fell into a river while climbing to his work area beneath a bridge. He was not wearing a life jacket or fall protection.
employee #1 had been working at level 42 and had taken a short break. En route to ground level, where he was presently assig
at about 3:45 p.m. on march 26, 1990, employees #1 and #2 were landing a precast slab for a bridge section. Employee #1 wa
at about 3:45 p.m. on march 26, 1990, employees #1 and #2 were landing a precast slab for a bridge section. Employee #1 wa
at about 11:00 a.m. on april 30, 1990, employee #1 was part of a crew placing steel decking on a web joist 23 ft above the grou
at approximately 9:30 p.m. on october 24, 1994, employee #1 was on a scaffold using a chain hoist to lift an access cover while
employee #1 was sitting on a partially dismantled stairwell and, with his feet, was guiding a new staircase that was being lifted i
an employer had contracted to build a new lime kiln at a mill. Part of the contract called for the construction of a network of new
an employer had contracted to build a new lime kiln at a mill. Part of the contract called for the construction of a network of new
an employer had contracted to build a new lime kiln at a mill. Part of the contract called for the construction of a network of new
an employer had contracted to build a new lime kiln at a mill. Part of the contract called for the construction of a network of new
an employer had contracted to build a new lime kiln at a mill. Part of the contract called for the construction of a network of new
at approximately 10:00 a.m. on october 23, 1991, employee #1 was helping to remove water well piping from a bore, and guide
employee #1 was working 300 feet in the air on a communications tower, installing side arm brackets to hold an antenna. He at
at approximately 7:30 a.m. on may 18, 1992, employee #1 was lowered by a backhoe bucket into a trench approximately 10 ft d
at approximately 10:30 a.m. on may 17, 1992, a mitsubishi (track type) backhoe was being used to dig a trench approximately 1
at approximately 9:30 a.m. on december 12, 1992, employee #1 poured approximately 1 gallon of diesel fuel into a 5 gallon me
at approximately 8:00 a.m. on february 26, 1992, employees #1 through #4, none of whom was wearing a life jacket, started to
at approximately 8:00 a.m. on february 26, 1992, employees #1 through #4, none of whom was wearing a life jacket, started to
at approximately 8:00 a.m. on february 26, 1992, employees #1 through #4, none of whom was wearing a life jacket, started to
at approximately 8:00 a.m. on february 26, 1992, employees #1 through #4, none of whom was wearing a life jacket, started to
an apprentice power line worker and another employee were working from a ford aerial lift at a height of 40 feet. The apprentice
employee #1 and a coworker were renovating a chimney. They were between the inner brick chimney lining and the outer conc
a job foreman was working from a scissor lift with a coworker, trying to find out why a row of ceiling lights was still flickering whe
employee #1 suffered a heart attack and died. The orange county medical examiner's report confirms the sheriff's officer's repo
a crew of employees was installing a 12-foot-high, 3-foot-wide, metal sluice gate at a sewage treatment plant. The work procee
at approximately 8:00 a.m. on or about october 1, 1990, employee #1 was performing his normal task of mixing fertilizers and s
an apprentice power line worker for an electric utility was making connections in a three-phase, 120/208-volt, 150 kilovolt-ampe
at about 10:30 a.m. on december 1, 1990, employees #1 and #2 were working with three coworkers who were installing catwal
at about 10:30 a.m. on december 1, 1990, employees #1 and #2 were working with three coworkers who were installing catwal
employee #1 was standing atop an oblong concrete pipe while cutting from one end of the pipe to the other with a gasoline-pow
an employee was using a defective electric saw that was connected to its source of supply through some extension cord sets. T
at approximately 5:10 p.m. on thursday, october 4, 1990, employee #1 and four other employees, one of whom was a foreman,
employee #1 was working from an 8 ft stepladder installing insulation batts in the wall and ceiling of the kitchen in a house unde
employee #1, a journeyman, and an apprentice of an electric service department were assigned to repair one of four lamps on
employee #1 was a member of a maintenance crew that was assigned to pull a filter feed pump for cleaning. An overhead hois
employee #1 was found dead on a stairway landing on the 5th floor level. There were no injuries apparent when the body was f
employee #1, a truck driver, was holding a tag line while a crane-borne metal truck trailer was being loaded piggyback-style on
three employees were installing well point risers for a de-watering system in preparation for a sewer line installation. The well p


                                                       Page 51
                                                          all


three employees were installing well point risers for a de-watering system in preparation for a sewer line installation. The well p
three employees were installing well point risers for a de-watering system in preparation for a sewer line installation. The well p
employee #1 was crushed and killed by the rear right tire of a lull 644 highlander ii high-lift. It is suspected that he was attemptin
a fourth-year apprentice electrician was in the lobby of a hotel connecting two ceiling lights to the lighting circuit. The hotel was
a four-man crew, including employee #1, was erecting a three-legged 180 ft tall communication tower. They were using a tulsa
employee #1, an electrician's helper, was using an 8 ft stepladder to install tie-wraps around some low voltage e.m.s. wiring. He
employee #1 was climbing a 10 ft 1 in. long ladder to access a landing that was 9 ft 2 in. above an adjacent floor. He was carryi
two electricians were installing a circuit breaker in an energized 480/277-volt, 800-ampere panelboard. One of them brought a t
employee #1 was standing near a drilling operation when a tool became caught, causing a whipping action. Employee #1 was s
at approximately 9:45 a.m. on march 6, 1995, employee #1, who was employed by a wall framing contractor, was pushing on a
at approximately 9:15 a.m. on june 7, 1994, employee #1, a foreman on a earthmoving construction site, climbed on a trackhoe
at approximately 8:30 a.m. on january 4, 1991, employee #1, a watchdog observer, was standing on the shoulder of the road, in
a power line worker was transferring an overhead power line from an old utility pole to a new one. He was working from the buc
employee #1 was helping a welder prepare a section of pipe for welding when the trench wall gave way and pinned him against
employee #1 was standing beside a county road and was struck and killed by wooden trusses that extended 2 1/2 ft on the righ
an employee was welding wear cracks in a 4-foot-by-6-foot-by-4-foot laundry tub. He was working in a wet environment. He app
a journeyman electrician and his helper were pulling conductors through emt conduit. The conduit carried existing energized co
at approximately 11:45 a.m. on january 18, 1992, employee #1, of great barrier insulation co., inc., was insulating a pipe that wa
on may 26, 1993, employee #1, who was without fall protection, was working on a roof top with a coworker. They were carrying
employee #1 picked up debris in front of a parked grader and carried the debris to a pickup truck located to the left and in front
employees #1 through #5 and three coworkers were removing and replacing steel roadway gratings and supporting beams on a
employees #1 through #5 and three coworkers were removing and replacing steel roadway gratings and supporting beams on a
employees #1 through #5 and three coworkers were removing and replacing steel roadway gratings and supporting beams on a
employees #1 through #5 and three coworkers were removing and replacing steel roadway gratings and supporting beams on a
employees #1 through #5 and three coworkers were removing and replacing steel roadway gratings and supporting beams on a
at 5:20 p.m. on april 20, 1993, employee #1 was filling in a 12 in. deep trench. He had driven the backhoe down the trench and
at approximately 8:30 a.m. on may 12, 1993, employee #1 reported to work. He was on the ground, standing in the shade at the
at approximately 7:45 a.m. on july 12, 1993, employee #1 and a coworker were working from two separate scissor lifts. They w
on march 7, 1991, employee #1 was at the top of a 16 ft high tubular scaffold installing electrical connectors in the overhead lig
employee #1 was a deckhand on a 42 ft, 20 gross ton tugboat that was pushing a barge up a river. He was sitting in a chair out
two employees were working in a 2-foot-deep trench, setting a well point into the ground. One of them was standing beside the
employee #1 and two other pipe layers were working with a dozer operator to lift a manhole cone with a john deere bulldozer, m
employee #1 was preparing to replace a gas line on a small compressor for a walk-in freezer. The compressor was located with
employee #1 had cut or pushed a large tree over with a front end loader and was limbing the tree. The saw became jammed in
employee #1 was on the fifth floor of a condo preparing the penthouse walls for painting. He was on the east side of the buildin
a job superintendent instructed a pipe foreman and a truck driver to back up a boom truck in a straight line and to leave the truc
at approximately 10:00 a.m. on september 26, 1991, employee #1, a laborer/roofer, was working for central florida roofing, thro
a painter was leaning over the roof of a three-story building, painting an exterior wall with a roller attached to an 8- to 10-foot alu
employee #1 was a flagger on a road building project and was struck in the back of the head by a boom/dump truck which was
employee #1 died of multiple injuries due to a fall from a 4-foot stepladder. He was attempting to replace a window at above-he
at approximately 11:00 a.m. on june 16, 1994, employee #1 was tuckpointing a chimney at st. Joachim's in chicago, il. He was
on march 25, 1995, at approximately 8:50 a.m., employee #1 was climbing an aluminum extension ladder to secure the platform
employee #1 was installing roof caps at the northwest corner of a 4:12 pitched roof of a residence when he fell 9 ft to the groun
employee #1 and a coworker had worked from a two point suspension scaffold for the entire eight hour shift. At approximately 3
employees #1 and #2 were working on a 12-inch wide aluminum scaffold plank (250 pound rating) that was suspended on ladd
employees #1 and #2 were working on a 12-inch wide aluminum scaffold plank (250 pound rating) that was suspended on ladd
employees #1 and #2 were drilling holes in the concrete floor of the east side dock area when a roof collapsed onto them. The
employees #1 and #2 were drilling holes in the concrete floor of the east side dock area when a roof collapsed onto them. The
employee #1 was disconnecting the chains and binders that had held various precast concrete sections on a semi-trailer during
at approximately 1:00 p.m. on february 22, 1995, employee #1 was cutting a portion of a damaged concrete roof. The roof sect
employee #1 was removing plywood sign panels from an outdoor advertising sign when he was struck by a panel and fell appro
employee #1 and a coworker were returning to the 18th floor of a building on a two point suspension scaffold. They had left the


                                                       Page 52
                                                         all


employee #1 was assigned to install insulation into the walls on a building's first floor. A coworker heard a noise and found emp
two apprentice electricians were replacing hall lighting fixtures in a high school. Some of the lights were to be connected to the
employee #1 was installing electrical wiring in a house under construction. He was found in the basement with an electric drill a
employee #1 was working below a chimney demolition operation, when he was hit and killed by a piece of the chimney removed
at approximately 11:41 on may 10, 1993, the menomonee falls, wi, fire department was called to treat employee #1, a roofer, w
at approximately 9:15 a.m. on may 14, 1993, employee #1 was unhooking chain slings from a trench shield that had been lowe
employee #1 and a coworker, both pile drivermen, were working in a storage yard separating two interlocked sheet pilings 33 a
on september 7, 1993, employee #1 was found lying face down on the floor. The medical examiner determined his cause of de
employee #1 was working on a phone line noise problem. To check the quality of the line, he climbed the utility pole in the back
employee #1 was struck and killed by a wire rope when a beam clamp slipped.
employee #1, the owner and only employee of inter lining, was working alone inside his shop fixing a urethane spray gun. He ap
employee #1, an apprentice, and a journeyman electrician coworker were working on the roof of a five-story building. Their job
at about 11:00 a.m. on december 30, 1993, employee #1 was on level 55 preparing reinforcing steel rods on a floor prior to pou
an employee was working alone on the roof of a garage that was attached to a house. He was self-employed and was building
while doing residential siding, employee #1 fell 12 ft from the roof of a porch to the concrete. He died.
shortly before 9:20 a.m. on september 20, 1994, employee #1, age 22, and a crew were installing a steel roof on top of a storag
employee #1 fell while climbing a tubular welded frame scaffold. He died of head and spinal injuries. No ladder was present.
employee #1 was installing a boiler when it fell over, due to an unstable base, and struck him. He died of a crushed chest. No w
on april 13, 1995, employee #1 was found next to his ladder on the ground at the base of a 21 ft high wall. He had apparently b
a backhoe/loader operator was backing up a 30 degree slope in order to position a jcb backhoe, serial #330.000, so that a hole
employees #1 and #2 were working under a single family wood structure. The structure had been jacked up in preparation for t
employees #1 and #2 were working under a single family wood structure. The structure had been jacked up in preparation for t
employee #1 was moving/placing steel decking onto bar joists. She fell 37 feet to the ground and was killed. Neither safety nets
employee #1 was one of four pile drivers working with a crane rig, boom hammer, and leads. They were using a lima 80t crawle
employee #1, the company president, was removing a porch overhang from a residential addition under construction. Roof trus
workers had been cutting curbs on a residential street and were moving to the next area to cut. Employee #1 was sitting on the
employee #1 was driving a tandem axle dump truck to deliver gravel. When he reached his destination, he crossed several sets
employee #1 was working from suspended scaffolding approximately 125 ft above the floor of a water tower. Part of the scaffol
employee #1 was operating a hall highlift rough terrain forklift, model 400-34, on a construction site. He was delivering material
two employees were working inside an aerial lift work platform. They were using a high pressure water hose to clean the exterio
two employees were working inside an aerial lift work platform. They were using a high pressure water hose to clean the exterio
employee #1 attempted to climb to the top of an unstable piece of electrical switchgear. The 1,200 to 1,400 lb unit fell on him. E
employee #1 was installing tar paper roof covering on a dormer located at the front of a residential building. The dormer had an
employee #1 and a coworker were on a communications tower, dismantling the 20 ft long top section that included attachment
employees #1 and #2 were rigging and preparing to lift a 65 ft long gin pole type derrick in order to dismantle a 200 ft cable tele
employees #1 and #2 were rigging and preparing to lift a 65 ft long gin pole type derrick in order to dismantle a 200 ft cable tele
employee #1 was an experienced operating engineer of a 1964 wabco d111a self-loading scraper at a landfill project. He was b
employee #1 was dismantling a wooden hood over the dryers on a paper machine when part of the 4 in. by 4 in. framing timber
employee #1, an iron worker, was applying double-faced tape to secure plastic-backed insulation to structural purlins before the
employee #1 was painting the exterior of a building while standing on an extension ladder that was set on top of a scaffold 3 bu
employee #1 was painting the exterior of a building while standing on an extension ladder that was set on top of a scaffold 3 bu
employee #1 was moving small amounts of sand along a roadside with a pointed, long handle shovel. He suffered a heart attac
employee #1 unintentionally backed a rubber-tired roller off the roadway into a steep ditch, causing it to roll over. He died from h
an employee was standing on a fiberglass stepladder, changing the ballast in an energized lighting fixture in a hospital kitchen.
employee #1 was checking a pump when he suffered a fatal heart attack.
a 31- year-old lead carpenter was building an addition to a large single family house. He was electrocuted when he picked up a
employee #1 and a coworker had been tuck-pointing a seven-story brick apartment building and had finished their work for the
employee #1, a utility construction worker, fell out of the back of a telecommunications truck as the truck rolled backward down
employee #1, age 70, walked behind a rubber-wheeled compactor that was ground leveling and was crushed to death.
employee #1 had just finished a roof repair and was getting onto a ladder to descend when he fell 16 ft to the ground. He died o
employees #1 and #2 were working in a vehicle-mounted aerial lift basket when the entire unit tipped to the side, causing them
employees #1 and #2 were working in a vehicle-mounted aerial lift basket when the entire unit tipped to the side, causing them


                                                      Page 53
                                                         all


employee #1 was erecting a guardrail/scaffold under a bridge when he unhooked his fall protection lanyard and walked approxi
a power line worker was holding a guy while his coworker was sawing off an old utility pole. The guy apparently contacted an ov
employee #1 happened to be between two 40 ft by 10 ft by 4 ft barges that were sitting on land for repair. While the excavator o
employee #1 was found dead of an apparent heart attack next to/under the truck bed. He may have been on the ground cinchin
employee #1, a self-employed hvac worker, was installing a duct in an attic. He collapsed and died of a heart attack.
Employee #1, along with 5 other employees, were in the process of loading 2 - 9 ft in diameter conduit reels containing conduit
on july 22, 1995, employee #1 and employee #2, a volunteer, were dismantling an abandoned railroad trestle one mile north of
a crew of five carpenters, including employee #1, had constructed the wood framework of a 2,400 sq ft storage building. The fir
employee #1 was hooking up a three-leg choker/sling onto a large fan unit for a baghouse. The fan unit was to be lifted onto a f
two power line workers were working from the two-person bucket of an aerial lift, installing a new 34.5-kilovolt overhead power
employee #1 was releasing a chain from the front bumper of a semi tractor-trailer. The chain had been used to pull the truck ou
a crew of five operators were using bulldozers and front end loaders to clear trees in a hilly and heavily wooded area for a golf c
on 1-22-90 deceased left the roof area at approximately 11;30am. While descending from the roof he fell into an elevator shaft
at approximately 4:00 p.m. on march 9, 1996, employee #1 and a coworker were manually moving a skyjack sjp 40 personnel l
employee #1 climbed a concrete formwork to remove a scaffold bracket that was approximately 22 feet above the ground. His
at approximately 10:30 a.m. on march 19, 1990, employee #1 was preparing to lower an empty tub from the open side of the se
employee #1 and a coworker were painting overhead structural steel from 6 ft stepladders that were adjacent to two operating s
at approximately 12:35 p.m. on december 1, 1995, employee #1 and two coworkers were returning to their work area after their
at 8:43 a.m. on october 21, 1996, employee #1 was welding down roof sheets onto asphalt in a roof area that was under constr
employee #1 was working at the 72 ft level of a free-standing tower on a 15 ft by 30 ft platform without guardrails. He was tighte
at approximately 9:10 a.m. on march 30, 1996, employee #1 climbed into a tree to saw off two limbs that were preventing a truc
on february 15, 1996, employee #1, a member of a three-man crew from j. l. manta, was refurbishing a tank at com ed's power
at approximately 12:50 p.m. on may 13, 1996, the operator of a ford f super duty 2 ton truck with an attached 20 ft long fifth whe
two employees were moving a 12.2-meter (40-foot) aluminum ladder they had been using on the north side of a residence. The
employee #1 and a coworker, a two-man demolition crew, were working on the roof of a 15 story building. Employee #1 was at
at 3:30 p.m. on august 22, 1992, employee #2 was installing a tire and multipiece rim wheel on the rear hub of a dump truck. E
at 3:30 p.m. on august 22, 1992, employee #2 was installing a tire and multipiece rim wheel on the rear hub of a dump truck. E
at approximately 11:15 a.m. on may 24, 1993, employees #1, #2, and #3 were working 20 ft high on a scaffold. A forklift was us
at approximately 11:15 a.m. on may 24, 1993, employees #1, #2, and #3 were working 20 ft high on a scaffold. A forklift was us
at approximately 11:15 a.m. on may 24, 1993, employees #1, #2, and #3 were working 20 ft high on a scaffold. A forklift was us
employee #1 was unloading an earthmoving dozer from a lowboy trailer. He backed the dozer partially off the lowboy's rear ram
employee #1 fell through a hole in the scaffolding while raising the scaffold to a new working height of approximately 78 feet 6 i
at approximately 7:20 a.m. on july 19, 1994, employee #1 was helping his coworkers plumb up a venture pipe (a large vertical p
three employees were moving an upright electrical panel box from a mezzanine onto a metal platform that was elevated by a fo
a crew of (5) five workers were installing insulation and metal sheeting on the roof of a 42 ft. High structural steel building. Emp
employee #1 was on the roof on a single-story home under construction. The pitch of the roof was 6:12 and the ground to eave
a two-person power line crew was replacing three transformers on a 7.6-meter-high (25-foot-high) wooden utility pole. One pow
employee #1 was installing a 12 in. diameter pvc drain tile in a 7 ft deep by 2 ft wide by 20 ft long trench in a farmer's field. The
at approximately 12:00 noon on july 29, 1996, employee #1, the sole owner of the company, was removing overhead electrical
employee #1 and a coworker were setting forms for concrete footings in a trench that was adjacent to an existing loading dock
employee #1 was struck by a 16 ft high by 80 ft long unbraced concrete block wall which blew over in high winds. He was killed
employee #1 was backing a bulldozer off a trailer when it rolled over. He was crushed to death under the rops. Seatbelts were n
an employee was working near the edge of a 18-foot-high flat roof. He had just finished making numerous trips up a 40-foot-lon
employees, preparing for drilling a second blast site, were in conference around the john henry drill rig, model #jh15. An explos
employees, preparing for drilling a second blast site, were in conference around the john henry drill rig, model #jh15. An explos
employees, preparing for drilling a second blast site, were in conference around the john henry drill rig, model #jh15. An explos
employees, preparing for drilling a second blast site, were in conference around the john henry drill rig, model #jh15. An explos
at approximately 1:40 p.m. on april 27, 1990, employee #1 was working at a dock storage area dismantling steel beams on an
employee #1 and workers employed by another employer stepped up onto the low end of a belt conveyor, which was supported
employee #1 and two coworkers were connecting sewer laterals in a 17 ft deep excavation dug in class c soil (loose sand). The
employee #1, a laborer, was operating a small john deere 450g bulldozer on level ground tracking forward. He got out of the op
at approximately 10:30 a.m. on february 14, 1992, employee #1, a civil engineer helper with mike hooks, inc., was operating a 1


                                                      Page 54
                                                         all


the employees were replacing a water line. At the time of the collapse, the employees were finishing the job at the deepest poin
a power line worker with 10 years' experience was connecting the service for a house to a transformer in a new housing develo
employees #1 through #5 were working at the citgo petroleum corporation refinery in lake charles, la. The "a" catalytic cracking
employees #1 through #5 were working at the citgo petroleum corporation refinery in lake charles, la. The "a" catalytic cracking
employees #1 through #5 were working at the citgo petroleum corporation refinery in lake charles, la. The "a" catalytic cracking
employees #1 through #5 were working at the citgo petroleum corporation refinery in lake charles, la. The "a" catalytic cracking
employees #1 through #5 were working at the citgo petroleum corporation refinery in lake charles, la. The "a" catalytic cracking
employee #1 and coworkers were installing new electric wire at an outdoor construction site. It had rained that morning and sev
on may 7, 1997, employee #1, a maintenance mechanic with nine years of experience with the plain dealing trucking co., inc., w
an employee was operating a drilling rig mounted on the bed of a truck. As he lowered the boom of the drilling rig, it contacted a
a foreman power line worker was moving a 10-kilovolt-ampere distribution transformer from the road side of a utility pole to the
a case 880b excavator (trackhoe) had been loaded onto a low boy trailer. Employee #1 was backing the truck and loaded traile
employee #1 was engaged in highway construction on an overpass 40 ft above ground level. A two-man crew was using a cran
at approximately 8:20 a.m. on march 1, 1993, employee #1, supervisor of the pipefitters for performance contracting, while disc
employee #1 worked for an electrical and instrumentation contractor. He was installing brackets on electrical conduit, which had
at about 9:55 a.m. on tuesday, may 4, 1993, employee #1 had been instructed to pick up trash from the low-pitch roof decking
at 6:30 a.m. on april 19, 1993, employee #1 arrived at the construction site, asking for work. He signed papers and started work
at 10:15 a.m. on october 12, 1996, employee #1 was rigging up a 24 in. valve that was to be lifted off a spud barge and onto a c
employee #1 drove a dump truck into a barrow pit site to haul mud from the pit to a flood protection levee under construction. A
employee #1 was part of an 11-man asphalt paving crew. They had finished work and were moving an asphalt material transfer
employee #1, age 69, had retired from the host company and was working as a contract laborer. He had been working alone in
at approximately 2:00 p.m. on march 20, 1997, employees #1 through #3, were performing maintenance and repair about 200 f
at approximately 2:00 p.m. on march 20, 1997, employees #1 through #3, were performing maintenance and repair about 200 f
at approximately 2:00 p.m. on march 20, 1997, employees #1 through #3, were performing maintenance and repair about 200 f
employee #1 was working from an a-frame wooden ladder approximately 10 to 12 feet above floor level. He was removing a de
at approximately 11:30 a.m. on november 7, 1990, a pre-fab octagon shaped space frame roof, weighing approximately 138 to
employee #1, an ironworker superintendent, was holding a tag line and directing the setting of a girder beam when a bulldozer
at approximately 12:00 noon on november 30, 1992, employee #1 was hammering markers near drain basins as a dump truck
a six-person crew was working on a saturday on the construction of a new metal building. Work was scheduled to continue on s
a six-person crew was working on a saturday on the construction of a new metal building. Work was scheduled to continue on s
at approximately 10:15 a.m. on august 17, 1992, employee #1 was working at a construction site inside british petroleum, allian
a power line worker was working from an insulated aerial lift, repairing a single-phase 7620-volt overhead power line. Lightning
at approximately 3:00 p.m. on september 24, 1992, employee #1 was working with a crew that was lowering a 6 in. wide and 12
employee #1 was working in the bottom of a 9 ft deep trench connecting and leveling concrete pipe when the west trench wall c
at approximately 12:15 p.m. on october 23, 1992, employee #1 was eating lunch on a raised area adjacent to a concrete pour b
employees were pouring a slab between the east and west papermill effluent clarifier tanks and had tasks to perform on the no
at approximately 4:35 p.m. on march 11, 1993, employee #1 was sitting on the lowered tailgate of a pickup truck to pick up traff
at approximately 8:30 a.m. on february 23, 1993, employee #1 and two other laborers were instructed by their foreman to get u
employee #1 was a helper working with a mechanic (the employer's name for an experienced roofer). At about 11:00 a.m. on m
a power line worker was installing knee braces on a wooden h-frame structure supporting an overhead power line. The structur
two power line workers were transferring overhead power lines from an old pole to a new one. One of the power lines (a distribu
an employee was installing a chain link fence at a residence. The employee lifted a 21-foot-long metal railing, and it contacted a
a crew was lowering a header into place for welding when employee #1 stepped into a floor hole. Employee #1 was wearing a s
employee #1 was walking under an i-beam when it fell, crushing and killing him. The accident occurred during the demolition an
an electrician was working from a 6-foot stepladder installing a lighting fixture. The lighting circuit was energized while he was w
employee #1 and other connectors were bolting perimeter beams into place between columns. The beams were being lifted to
an employee was setting up to install bolts on an overhead power line. He simultaneously contacted an energized line and grou
employee #1 was attempting to even a double hooked cable, used with a track mounted front loader, to pull down a column in a
employee #1 was walking backward toward the edge of a roof holding the end of a steel tape measure. He walked off the roof,
employee #1 was attempting to mount a d3b caterpillar bulldozer by stepping on the tow pintle frame at the rear of the machine
employee #1, a journeyman electrician at a construction site, had been employed since august 13, 1991. He left the ground floo
at approximately 4:00 p.m. on september 4, 1991, employee #1 was placing 4 in. by 6 in. planks across beams, between colum


                                                      Page 55
                                                          all


an employee was using a case backhoe to locate a 102-millimeter-diameter (4-inch-diameter) water pipe. While he was digging
a crane was being used to move a load of soil. The crane was on wooden pallets. An electric cord for a light was attached to th
employee #1 was removing insulation from a roof when his foot slipped and he fell through a 4 1/2 to 6 ft gap between the old a
an employee was electrocuted when he touched an energized duct while he was also in contact with a grounded duct. The duc
employee used a 3 foot high portable step-ladder to gain access to a pipe rack 7 1/2 feet high while standing on the rack he slip
employees #1, #2, and #3 were drilling fence post holes in the unventilated basement of a building. They were overcome by ca
employees #1, #2, and #3 were drilling fence post holes in the unventilated basement of a building. They were overcome by ca
employees #1, #2, and #3 were drilling fence post holes in the unventilated basement of a building. They were overcome by ca
employee #1 was looking through a surveyor's transit, shooting a line for highway construction on highway 6. He was struck an
employees #1 and #2 were walking on the dirt along a paved shoulder and were struck by an automobile driving in the same di
employees #1 and #2 were walking on the dirt along a paved shoulder and were struck by an automobile driving in the same di
employee #1 was installing sheet metal on a 26 ft high roof when his tennis shoes slipped on the wet surface. He slid off the roo
employee killed.
at approximately 4:15 p.m. on august 6, 1990, employee #1 was removing damaged insulation from an approximately 30 ft high
an electrician was standing on the fourth rung of a 6-foot fiberglass stepladder, troubleshooting conductors in a junction box loc
at approximately 7:55 a.m. on october 12, 1990, employee #1 was positioned on the south side of a concrete column hooking u
employee #1 was a laborer and the brother of the excavator operator. The two of them and another laborer were moving three
scaffold boards that were being lifted by a crane fell when they struck guardrails and fell on employees working below. Employe
employee #1, wearing a safety belt and lanyard, climbed a 300 ft radio transmission tower. He was 120 ft above ground when h
employee #1 jumped off his moving dozer to avoid a falling overhead power line which was struck by a dump truck. He was cau
at approximately 11:18 p.m. on december 4, 1990, employee #1 was working on the left hand emergency lane facing northboun
employee #1 was removing boom connecting pins from a crane's lattice boom, which was not supported. When the pins were r
employees #1 and #2 were in a trench when the wheels of a dump truck loaded with sand went over the edge of the trench. Th
employees #1 and #2 were in a trench when the wheels of a dump truck loaded with sand went over the edge of the trench. Th
employees #1, #2, and #3 were doing road repair when a drunken truck driver hit a second truck. Both trucks went through the
employees #1, #2, and #3 were doing road repair when a drunken truck driver hit a second truck. Both trucks went through the
employees #1, #2, and #3 were doing road repair when a drunken truck driver hit a second truck. Both trucks went through the
employee #1 was standing/working inside a barricaded area located between highway lanes 3 and 4 (lane transition area) of th
at approximately 11:30 a.m. on july 26, 1997, employee #1, an asphalt distribution truck operator, was preparing to spray a coa
the victim was on the ground working in front of a motorized road sweeper and behind a paving machine. The paving machine
on july 3, 1997 around 4:30 pm, employee age 29, in the course of construction work drowned as he swam from a barge to the
employee #1 was working around an open 35 in. by 41 in. chute top 25 ft above the floor. The chute was part of a sewage treat
employees #1 and a coworker had climbed the formwork to the top of a 14 ft column form to make a concrete pour from a hose
at approximately 4:28 p.m. on january 15, 1990, employee #1 and two other laborers were standing on a combination plywood
at approximately 1:00 p.m. on june 26, 1995, employee #1 had been tunneling under the cement slab of a house to replace sew
a journeyman power line worker had elevated himself and a coworker in an insulated aerial lift. Rubber insulating equipment wa
a journeyman power line worker had elevated himself and a coworker in an insulated aerial lift. Rubber insulating equipment wa
at approximately 2:15 p.m. on march 21, 1990, employee # 1 and a coworker were approximately 70 ft above floor level in an h
at approximately 1:00 p.m. on july 22, 1991, employee #1 turned on the gas supply to the camper trailer and then went into the
employee #1 was 36 ft above the ground, retrieving and installing styrofoam blocks on a roof; he was not tied off. While he was
on september 4, 1992, a crew of five employees was removing damaged pier pilings from 30 feet of water. With up pull tension
on september 4, 1992, a crew of five employees was removing damaged pier pilings from 30 feet of water. With up pull tension
a refinery hydrofluoric acid pump repressured during motor replacement operations. Employee's confusion due to lack of locko
a refinery hydrofluoric acid pump repressured during motor replacement operations. Employee's confusion due to lack of locko
a refinery hydrofluoric acid pump repressured during motor replacement operations. Employee's confusion due to lack of locko
a refinery hydrofluoric acid pump repressured during motor replacement operations. Employee's confusion due to lack of locko
a refinery hydrofluoric acid pump repressured during motor replacement operations. Employee's confusion due to lack of locko
a refinery hydrofluoric acid pump repressured during motor replacement operations. Employee's confusion due to lack of locko
a refinery hydrofluoric acid pump repressured during motor replacement operations. Employee's confusion due to lack of locko
employee #1 and two coworkers were installing 3 ft wide by 15 ft long pieces of aluminum sheet roofing approximately 19 ft from
two employees were working on a scissor lift, installing closure plates. One of them was sitting on the lift's guardrail with his righ
at approximately 1:30 p.m. on february 28, 1995, employees #1 and #2 were preparing to connect a length of pipe that was 13


                                                      Page 56
                                                         all


at approximately 1:30 p.m. on february 28, 1995, employees #1 and #2 were preparing to connect a length of pipe that was 13
a power line worker was working on an overhead power line. An energized conductor line behind him was not fully insulated, an
at approximately 9:00 a.m. on june 20, 1995, on their first day on the job, a supervisor took employee #1 and a coworker to the
a construction helper was installing fluorescent tubes in lighting fixtures. A foreman heard the employee fall, but there were no w
employee #1 had been placing bolts and nuts in connection plates at the end of support beams on the second floor of the pc ie
at approximately 4:30 pm, on august 18, 1992, employee #1 had been working as the front-end man on the spreader box equip
at approximately 11:50 a.m. on october 22, 1991, employee #1 went to tell the spotter to move trucks so that a cement truck co
at approximately 3:06 p.m. on january 10, 1992, employees #1 and a coworker were applying decals to the canopy of a gas pum
two employees were attaching an assembled metal roof to a spreader on the load line of a crane. One of the employees was ho
two employees were attaching an assembled metal roof to a spreader on the load line of a crane. One of the employees was ho
at approximately 11:50 a.m. on october 4, 1994, employee #1 was installing rafters and beams at a height of approximately 11
while backing his belly dump semi-trailer truck into position, a truck driver backed over employee #1. He then proceeded forwar
employee #1 was unloading an air handler from a lift that had been raised to the mezzanine level. He had spread his legs over
an employee was installing electric appliances. He was electrocuted when he contacted an energized part of an electric circuit t
employee #1 was using a pry bar to position a 6 ft by 20 ft by 1/4 in. steel sheet on the roof of a tank. He fell 43 ft from the roof
while engaged in vinyl tile removal at an occupied single family residence, a work crew, including employee #1, was using lacqu
from between 9:00 a.m. and 10:00 a.m. on august 19, 1995, employees at lehne & forbes were pouring concrete in very high te
from between 9:00 a.m. and 10:00 a.m. on august 19, 1995, employees at lehne & forbes were pouring concrete in very high te
on or about march 23, 1996, employee #1 and a coworker were gathering soil samples from previously drilled holes in the earth
a mechanic from the company replaced a broken 3/4" male nipple along with a 3/4" male/female quick connect coupling, part #
On or about May 13, 2000, at approximately 11:30 a.m., employee #1 was run over by a CP 132, diesel engine, Dynapac Pneu
at approximately 1:50 p.m. on february 15, 1995, employee #1 was welding roof decking atop a newly constructed warehouse.
employee #1, a warehouseman/truck driver, did not report to work on the morning of may 15, 1995, but was seen in the building
a welder was working about 10.7 meters (35 feet) above a concrete floor, welding on a steel column that supported overhead c
at approximately 3:00 p.m. on july 18, 1996, employee #1 was preparing to install sheet metal air conditioning ducts in the engin
at approximately 2:50 p.m. on july 21, 1995, employee #1 was welding on a flat, metal roof of a structural steel building. He was
at approximately 10:30 a.m. on june 19, 1996, employee #1 was performing refractory work, spraying insulating material inside
at approximately 7:45 a.m. on july 26, 1995, employee #1 was on the first floor when he apparently opened the outside door of
trench not shored; caved in onto employee #1 at the intersection of ennis & commerce street in houston, texas.
at approximately 11:00 a.m. on february 21, 1997, employees #1 and #2 and coworkers were using a crane to place a 64 ft tall
at approximately 11:00 a.m. on february 21, 1997, employees #1 and #2 and coworkers were using a crane to place a 64 ft tall
a power line crew was replacing a broken utility pole. One of the employees on the crew was standing on the side of the digger
a power line crew was replacing a broken utility pole. One of the employees on the crew was standing on the side of the digger
at approximately 1:50 p.m. on january 16, 1997, employee #1 and four coworkers were working 40 ft above the concrete floor in
employee #1 was dismantling a crawler crane's lattice boom. He removed the boom pins from the foot section joint without sup
at approximately 9:34 a.m. on june 7, 1997, employee #1 was moving hydraulic lines on a pile driver for a sandblasting pit unde
while employee #1 was working painting, from an unsecured aluminum ladder position in a stairwell on concrete floor at about a
a supervisor backed a backhoe into an excavation. It landed on employee #1, killing him.
a rough-terrain hydraulic truck crane was hauling a load of cross-ties when it tipped over. Its boom struck and killed employee #
employee #1 was installing rebar at a construction site. He complained of dizziness and collapsed. He died of an apparent hear
employee #1 (name unknown) was unloading a rail car and was struck in the head by the dome lid of the tank car. He was kille
an employee was using a truck-mounted hydraulic crane to unload materials at a construction site. The boom of the crane cont
employee #1 was installing rebar on a bridge being constructed. He fell from the bridge and was struck and killed by an automo
employee #1 was on the back of a trailer hooking tongs onto a beam that was being off loaded. The crane jerked the beam, ca
employee #1 was walking from one work site to another when he was struck and run over by a dump truck. He was killed.
employee #1 was operating a roller equipped with a roll-over protection cab and seat belts. The roller overturned and the roof o
the driver of a vehicle pulled away from the side of the road and drove up the road for approximately 75 ft before stopping to tal
as employee #1 grabbed a 30 in. pipe to pull himself out of a rack, the pipe rolled onto his chest, knocking him backward where
employee #1 was on an a-frame ladder 20 ft above a concrete floor removing 8 in. pipe. A pipe sprang out of the clamps, knock
at approximately 9:00 a.m. on february 28, 1994, a laborer was supplying mortar and bricks to a mason, when he noticed emplo
employee #1, a flagman, misjudged the turn radius of a tractor trailer truck. Thinking that the truck had finished its turn, he turne
employee #1 was removing pipe from a truck. When a strap was removed, a pipe rolled off the truck. The pipe struck and killed


                                                      Page 57
                                                        all


employee #1 died of a heart attack caused by congestive cardiomyopathy. The employee died of natural causes.
employee #1 died of heart failure while starting work.
employee #1 was part of a crew doing highway maintenance when a car's brakes failed and the car, out of control, went throug
employee #1 was discovered dead on site. There was no apparent physical damage to the employee's body.
employee #1 was discovered dead on site. There was no apparent physical damage to the employee's body.
employee #1 was on an 8 ft ladder securing together two air conditioning vents that were approximately 13 ft from the floor. He
employee #1 had been working for a company about two weeks. After he had worked approximately 7 hours one day hanging d
an employee was connecting conductors from a 112.5-kilovolt-ampere transformer. The transformer, which was not deenergize
employee #1 was seen early in the morning spray painting a wall of a new warehouse. It is believed that he became entangled
employee #1 was grinding the tight space between both ends at the bottom of 10 in. pipes. When he retracted the grinder appr
employee #1 was riding on the left side of a cherry picker and fell off. He was run over by both left wheels and died.
employee #1 was standing on angle iron supports, removing bird nests from inside a filler sign that had billboards on both sides
an 11 ft deep trench caved in, crushing employee #1 against a 4 in. diameter concrete pipe. He was killed.
employee #1 was picking up welding rod debris on the 14th level of a tower under construction. He was walking around the tow
employee #1, a laborer, was working in a 19 ft long by 9 ft 10 in. wide by 6 ft 8 in. to 7 ft deep trench. A backhoe had made a ho
employee #1 removed a pipe plug bleed of a connection from a transmitter that was under pressure from hydrogen sulfide gas.
an employee was electrocuted. (The original report did not give any details about the accident.)
employee #1 entered a sewer to measure the diameter of a pipe. He was overcome by gas and killed.
employee #1,an iron worker, returned from lunch and was walking along steel girder getting ready to start decking on south sid
an employee was moving a 9.8-meter-long (32-foot-long) aluminum extension ladder away from a building. The upper section o
while performing electrical maintenance work in a power substation, employee #1 opened insulating shutter covering live circuit
on april 4, 1998 at approximately 1:25 p.m., employee #1 was demolishing walls in the interior of an office. Employee #1 grabbe
following a rain storm, while erecting and bracing a first floor wall on the "clubhouse" of an apartment complex, decedent was p
On or about July 29,2000 at approximately 1:45am where employee #1 was working from a six- foot, fiberglass,step ladder, con
On May 04,2000, at approximately 3:00pm, employee #1 was standing in a ditch with water. Employee #1 was holding a 1/4 inc
while dismantling scaffolding in delayed coker unit (dcu), employee #1 fell 40 ft withng cell#2 cooling tower, landing in seven fee
a flash explosion on july 23, 1998 caused two employees to be burned and fall. The employees were hospitalized. One employe
a flash explosion on july 23, 1998 caused two employees to be burned and fall. The employees were hospitalized. One employe
a flash explosion on july 23, 1998 caused two employees to be burned and fall. The employees were hospitalized. One employe
fall from roof
at approximately 9:30 a.m. on july 10, 1990, employee #1, a member of a pipeline crew, was installing pipe in a trench on a city
a crane operator and a foreman were using a truck crane (with slings) to raise a piece of equipment to an upright position. The
a power line worker was constructing a new overhead power line. He was working from an articulating boom aerial lift, connecti
employee #1 entered a frac tank during an oil well swabbing operation to collect a sample of well fluids. He was asphyxiated by
employee #1 was assisting the equipment operator in starting the caterpillar pipelayer when it started reversing. The pipelayer m
a contractor hired two employees to work as temporary laborers on a jobsite. The two employees, along with other employees,
a contractor hired two employees to work as temporary laborers on a jobsite. The two employees, along with other employees,
employee #1 was laying pipe below ground for a storm drain system in a 5 ft trench that had a bottom layered with sand. After w
at approximately 11:00 a.m. on august 7, 1991, employee #1 was helping to strap pvc pipe into the bed of a flatbed truck at a w
employee #1 was descending the ladder leg of a water tower that was being painted when the horizontal flat bar that he was ho
a crawler crane had been used to lift a pump from the ground to the top of an elevated highway under construction. The wire ro
a nine-person crew was applying cold material to the shoulder of a roadway in a suburban residential area where they had prev
at approximately 4:15 p.m. on november 13, 1991, employee #1 pulled his rubber-tired ingram pneumatic roller up on an incline
on december 4, 1991, employee #1, a pumpman for t. l. james, was assigned to watch a 1,765 lb gorman-rupp centrifugal pum
two employees were installing metal trim on a galvanized metal building. They brought a piece of trim into contact with a 7000-v
two employees were installing metal trim on a galvanized metal building. They brought a piece of trim into contact with a 7000-v
employee #1 was about to assist another employee in spreading metal roof decking across bar joists. Employee #1 stepped fro
employer was preparing mile long bridge k-16 for resurfacing. There were motion detector stop lights at each end of the bridge.
employer was preparing mile long bridge k-16 for resurfacing. There were motion detector stop lights at each end of the bridge.
employee #1 was working from a 14 ft high scaffold troweling grout on the top course of block in order to finish up a concrete b
employee #1, a self-employed welder, was welding rebar onto a steel structure of a building in order to hang brooms. There wa
employee #1 was shoveling debris from a newly-paved asphalt base for an access road. A kdot inspector was on the job site in


                                                     Page 58
                                                        all


september 8, 1995 was employee #1's first day back to work following the death of his mother. He loaded a marklift 62, compa
a power line worker and an apprentice were installing a new static wire for an overhead power line. The static wire was being st
a power line worker and an apprentice were installing a new static wire for an overhead power line. The static wire was being st
employee #1 was a member of a five-man crew that was laying 50 ft by 30 in. sections of metal roofing at a height of approxima
on october 17, 1995, employee #1 was part of a three man crew that had delivered a crane to a new job site. The crane was re
employee #1 was digging an excavation to bury road materials. He apparently dismounted his backhoe and entered the excava
employee #1 was performing steel erection work on a low slope roof. A crew of five employees was laying the first piece of met
while other roofers were on the ground setting up, employee #1 and two coworkers were on the roof of an apartment complex u
a power line worker was connecting a conductor on an overhead power line. His head contacted a 72-kilovolt power line located
a carpenter walked across a floor inside a building. He walked into a puddle of water that had an energized power line lying in it
employees including employee #1 were attempting to unload a headache ball from a 1 ton flatbed truck. The truck had been ba
a painter was moving a metal ladder. The ladder contacted an overhead power line, and the painter was electrocuted.
helping to build a basement under an existing house, employee #1 was using a basement screw jack from underneath the hous
employee #1 was working in a trench when the shoring failed. He was struck and killed by the falling earth and form material.
employee #1 was working in a trench when the shoring failed. He was struck and killed by the falling earth and form material.
at approximately 5:00 p.m. on june 10, 1996, employee #1, a millwright, was in the east leg boot pit preparing to adjust the pulle
employee #1 was building and removing concrete wooden forms when he complained of a fast heart beat, sat down, and then p
employee #1 was driving a front end loader a distance of 2 to 3 miles on highway c, where it was going to be used to dig a wate
at approximately 12:50 p.m. on january 22, 1992, employee #1, a carpenter, and employee #2, a laborer, were working below ir
at approximately 12:50 p.m. on january 22, 1992, employee #1, a carpenter, and employee #2, a laborer, were working below ir
on june 12, 1992, employees were driving piling into the ground. They had driven three pilings and were starting on the fourth. A
at 11:40 p.m. on july 27, 1992, employee #1, a journeyman iron worker, was welding bar joists 22 ft above ground level. Eviden
employees #1, #2, and #3 were working on top of an approximately 10,000 gallon chemical storage tank. The last known conte
employees #1, #2, and #3 were working on top of an approximately 10,000 gallon chemical storage tank. The last known conte
a crew of electricians for a contractor was working in the crusher house of an electric power generating station, installing new s
on june 23, 1993, employees #1, #2, #3, and #4 were in a sewer relining it with sprayed concrete. At 1:00 p.m., rain began to fa
on june 23, 1993, employees #1, #2, #3, and #4 were in a sewer relining it with sprayed concrete. At 1:00 p.m., rain began to fa
on june 23, 1993, employees #1, #2, #3, and #4 were in a sewer relining it with sprayed concrete. At 1:00 p.m., rain began to fa
on june 23, 1993, employees #1, #2, #3, and #4 were in a sewer relining it with sprayed concrete. At 1:00 p.m., rain began to fa
employee #1 and a coworker were walking out of an 8 1/2 ft deep trench when a side of the trench collapsed, burying employee
employee #1 had placed the top half of an aluminum ladder on a drive-in to climb 13 ft to the roof. The bottom of the unsecured
a power line worker was transferring a 7620-volt overhead power line from an old utility pole to a new one. He was climbing the
at approximately 4:55 p.m. on january 13, 1994, employee #1 was using a caterpillar bulldozer to push rock into a pile. He was
two power line workers were removing hardware from a utility pole. They were in an insulated aerial lift, removing a bolt at the t
two power line workers were removing hardware from a utility pole. They were in an insulated aerial lift, removing a bolt at the t
at approximately 2:40 p.m. on march 14, employee #1, who was positioned at the northwest corner of an air conditioning unit, w
an employee, who was standing in 6 inches of water and who was wearing tennis shoes, was draining the water from a swimm
on march 15, 1993, employees #1 and #2 were using methylene chloride to strip the floor of a squash court. They used about 1
on march 15, 1993, employees #1 and #2 were using methylene chloride to strip the floor of a squash court. They used about 1
at approximately 8:20 p.m. on september 1, 1994, employee #1 was inside a cage sandblasting the top flange of an i-beam on
employee #1 and coworkers had just finished burying telephone cables in the ground and were proceeding back to the highway
employee #1 had just finished placing a case 580d backhoe on a trailer and was preparing to secure it when he noticed the boo
at approximately 7:00 a.m. on november 21, 1994, employee #1 and a coworker, laborers, began removing the rubber bladder
at approximately 8:40 a.m. on march 27, 1995, employee #1, a laborer, was laying pipe in an approximately 11 ft deep trench. H
at approximately 8:37 a.m. on may 18, 1995, employee #1 was approximately 45 ft above ground level on a roof helping a cowo
at approximately 12:45 p.m. on april 19, 1995, employee #1 (a crane oiler) and a coworker (the crane operator) were preparing
a structural metal worker was rigging 8.4-meter-long steel i-beams to the load line of a link belt crane. The crane was about 45
an employee was standing on a scaffold, installing a fence. Apparently, while he was holding onto a fence post, the employee r
an employee was working from an aluminum ladder at a distance of 5 feet from a 15-kilovolt overhead power line. While he wa
at approximately 3:20 p.m. on april 16, 1992, employee #1 was attempting to lower a ventilation hood 59 feet to the ground. Thr
two employees were placing a ladder against an apartment building so that they could paint the eaves of the building. Reported
employee #1 and a coworker were rigging forms to be off loaded from the bed of a truck by crane. When the crane operator lift


                                                     Page 59
                                                        all


employee #1 was 15 feet above ground level installing roofing felt on a flat roof. He was at the roof edge and outside the warnin
at approximately 5:00 p.m. on october 3, 1994, employee #1 was working in a 9 ft deep trench in class c soil. The walls were st
employee #1 was installing a new roof when he slipped onto the fall protection system. The system failed to hold him and he fe
employee #1 was installing shingles on a roof 20 to 23 feet above the ground. Employee #1 slipped and fell, receiving fatal injur
the operator and employee #1, a passenger, were riding uphill on an asphalt roller to get from one driveway, which had just bee
employee #1 was installing formwork on the rebar side of a concrete form. A gust of wind blew the form over on the employee,
employee #1 was installing formwork on the rebar side of a concrete form. A gust of wind blew the form over on the employee,
employee #1 was operating a mustang skid steer loader to move dirt around a house foundation. Employee #1 was reaching in
at approximately 12 noon on july 7, 1991, employee #1 was doing touch-up painting on grain bins above a truck dump. Access
a power line worker was installing a 7200-volt overhead power line on new utility poles. The employee contacted one of the pha
employee #1 was installing 20 ft by 3 ft steel sheeting on a roof 16 ft above ground. He jumped to the next building roof and fell
an electrical contractor was installing electric equipment at an oat mill. The contractor was the sole owner of his company. He w
at approximately 6:45 p.m. on march 11, 1994, employees #1, #2 and #3 were working approximately 400 feet high on a cellula
at approximately 6:45 p.m. on march 11, 1994, employees #1, #2 and #3 were working approximately 400 feet high on a cellula
at approximately 6:45 p.m. on march 11, 1994, employees #1, #2 and #3 were working approximately 400 feet high on a cellula
employee #1 was 25 feet above the ground straddle walking two steel i-beams. He was installing a coil bolt for a concrete form
at approximately 2:55 p.m. on october 28, 1992, employee #1 was troubleshooting a spark ignition problem (there was no pilot)
a plumber was using a pipe wrench to remove a water line from a toilet. The water line was energized because of faulty wiring.
employee #1 was operating an earth scraper on a highway job adjacent to highway 77. At approximately 2:30 p.m. on august 1
employee #1 was pumping out a livestock sewage lagoon. This process involved two tractors, a pump, and an agitator. Employ
employee #1 was standing in a trench 2 1/2 feet wide and 8 to 12 feet deep installing a water line under the footing of a residen
employee #1, with the help of 2 coworkers, was constructing a work platform in an elevator shaft to install a header. Employee
at approximately 9:30 a.m. on december 23, 1994, employee #1 was 23 feet above a concrete floor, installing a roof deck. He w
employee #1 was installing felt underlayment on a roof in preparation for installation of shingles. Employee #1 began to slip ove
an employee was asked to remove an aluminum ladder from a metal fire escape. The ladder was being used for access to a ro
at 8:15 a.m. (break time), employee #1 sat on the edge of a plexiglass skylight located on the roof and removed his shoe and s
employee #1 was tied off to a power transmission tower to install rigging for running electric lines. He had gained access to the
at approximately 2:00 p.m. on october 18, 1991, employee #1 was attempting to remove the dirt scoop from a new holland bob
employee #1 was tightening the bolts on the flange of a 10 inch water line that was leaking due to testing of the lines under pres
employee #1, a journeyman electrical lineman, was climbing a wooden power line pole to replace the insulators. Apparently one
employee #1 and three other ironworkers, one of whom was the foreman, were standing on a roof truss of a building under con
employee #1 was a member of a five-person crew installing the roof of a steel aircraft building. He and a coworker were putting
employee #1 was using a forklift to unload and stack steel i-beams when he was crushed between two beams. Employee #1 w
employee #1 was helping remove old, loose roofing from the gallery (texas house) roof of a grain elevator. He had his back to t
employee #1 was standing in a manlift cage approximately 1,250 ft above the ground. His lanyard was attached to the ladder o
employee #1 was killed when he fell into a moving conveyor on a cedar rapids mobile asphalt plant.
employee #1 was approximately 57 ft above ground level applying caulking to the seams on the roof of a grandstand. He was w
employee #1 was laying pvc sewer pipe in a 13 foot 3 inch deep sewer trench. The east wall of the trench caved in, burying and
employee #1 had just dismounted from a pavement roller after having a discussion with the operator regarding ear protection. H
employee #1 hooked the fresh air line of his air supplied respirator into a plant's compressed air lines, then began some abrasiv
employee #1 was operating a tracked dozer to restore a farm pond dam. He dismounted the dozer for an unknown reason and
employee #1 and coworkers were installing 13 ft long sections of 8 in. diameter pvc sewer pipe in a 9 ft deep trench. The west w
three employees were using a forklift to move a 23-foot-high section of tower scaffold from the north corner of a building under
three employees were using a forklift to move a 23-foot-high section of tower scaffold from the north corner of a building under
three employees were using a forklift to move a 23-foot-high section of tower scaffold from the north corner of a building under
employee #1 and three coworkers were involved in detail roofing work on a barrel-type roof that measured 22 ft at its crown and
employees #1 and #2 were using a caterpillar 215 backhoe with a hydra hammer attachment as a jackhammer to demolish an
employees #1 and #2 were using a caterpillar 215 backhoe with a hydra hammer attachment as a jackhammer to demolish an
employee #1 had climbed to the top of a 60 ft lead tower to remove the crane hook from the top of the lead after removing the c
employee #1 was removing gravel and soil from an excavation near the basement wall of a multi-storied building structure. A ca
employee #1 was a general laborer involved with the installation of an underground water piping system. He was a new hire on
three employees were using a boom truck to unload metal road forms from the bed of the truck. One employee was standing o


                                                     Page 60
                                                        all


at approximately 2 p.m. on february 12, 1990, employee #1 and three coworkers were installing a rubber flexible liner in an exc
at approximately 2 p.m. on february 12, 1990, employee #1 and three coworkers were installing a rubber flexible liner in an exc
employee #1, a roofer, was removing plywood from a flat roof and placing the wood into the elevated bed of a dump truck. The
employee #1 was walking from the outside left center of a gomaco ps-48 paving placer/spreader between the outside of the co
two power line workers were connecting an underground electrical service lateral to a newly constructed house. One of them w
employee #1 was working on the second or third rung from the bottom of a ladder. A fellow employee heard a grunt, turned, an
at 11:00 a.m. on november 8, 1993, employee #1 was removing a roof that was to be replaced when he went through a tile tha
employee #1 was removing electrical lines from the top of a utility pole when the pole fractured below ground level and fell over
employee #1, a bulldozer operator, was prying out a tree stump when a tilt cylinder hydraulic line failed. Because the accident o
employee #1 was installing roofing material that was 10 in. wide by 20 ft long near the edge of the roof. He had completed a 20
at approximately 1:45 p.m. on march 31, 1994, employee #1, three coworkers, and one state inspector were working inside an
employee #1 was the foreman of a three-person crew that was laying decking on the third floor of a structural steel building. He
at approximately 10:30 a.m. on june 17, 1993, employee #1 was standing on a truss that was approximately 30 feet above a co
at approximately 9:30 a.m. on june 1, 1992, employee #1 was 20 ft above the ground installing insulation from an elevated work
as employee #1 attempted to jump out of a truck that was rolling toward a 14 ft hole, his foot was caught between the driver's s
at approximately 11 am on june 30, 1992, employee #1 was assigned the duties of a flagman to merge the highway traffic into a
at approximately 3:00 p.m. on august 20, 1992, employee #1 was washing chips of paint from a sloped roof when he apparentl
employees #1, #2, and #3 were installing a liner in an existing sewer line. A surge of hot liquid broke through the protective bulk
employees #1, #2, and #3 were installing a liner in an existing sewer line. A surge of hot liquid broke through the protective bulk
employees #1, #2, and #3 were installing a liner in an existing sewer line. A surge of hot liquid broke through the protective bulk
employee #1 was preparing a gravel bed in a trench to lay a 20 ft long by 8 in. diameter pipe. The trench was approximately 22
at 10:30 a.m. on january 28, 1991, employee #1 was at a height of 35 ft on a universal manufacturing company carpenter's bra
at 10:30 a.m. on january 28, 1991, employee #1 was at a height of 35 ft on a universal manufacturing company carpenter's bra
at 10:30 a.m. on january 28, 1991, employee #1 was at a height of 35 ft on a universal manufacturing company carpenter's bra
employee #1 was riding with a roofing crew in a pickup truck to a local grocery for a restroom break. The truck was struck when
employee #1, a crane operator, had just finished three lifts for the iron workers employed by a sub-contractor and apparently le
an employee was installing siding on an apartment building. A 7620-volt overhead power line was located between 6 and 7 feet
at approximately 10:10 p.m. on july 7, 1992, employee #1 was directing a coworker in backing a 1979 mack truck up to an asph
employee #1 was using a d-6 bulldozer to load a piece of equipment onto a lowboy flatbed trailer. When the bulldozer slipped o
employee #1 was in an 8 foot deep trench trying to locate a water line. A large piece of dirt came off of the side of the trench an
employee #1 was working on the first floor of a home under construction when he fell through an uncovered floor opening to the
employee #1 was moving a tractor loader/backhoe onto a trailer. He left the operator's position while the engine was running an
at approximately 8:00 a.m. on march 27, 1990, employee #1 and coworkers were excavating and reclaiming a gravel pit that ha
employee #1 and coworkers raised a hi-lo multistage two-point suspended scaffold, model #d-800, until the bottom deck was a
employee #1 was attempting to dismantle the boom from a truck crane. The boom was approximately 6 feet above ground leve
at approximately 2:30 p.m. on july 8, 1991, employee #1 was dumping a load of rocks while operating a new ford holland skid-s
on or about june 26, 1991, employee #1 was installing sheetrock and firestone rubber roofing material while reroofing a school
at approximately 2:30 p.m. on august 21, 1991, employee #1 was attempting to remove a stick that was lodged under a d-6 cat
employee #1 was checking grade at the warm springs arco project north of i-90. He was on foot near a bulldozer and other hea
employee #1 was hauling timber slash down a haul road to a burning pile. The machine backed off the road and rolled over, pin
at approximately 3:30 p.m. on december 12, 1992, employee #1 was on a ladder cutting down a cable tv drop assembly. When
two employees were removing a portable light. It contacted a 7200-volt overhead power line, and both employees received elec
two employees were removing a portable light. It contacted a 7200-volt overhead power line, and both employees received elec
at approximately 2:30 p.m. on august 3, 1992, employee #1 was wading/swimming across a section of the yellowstone river in p
two power line workers were removing two deenergized conductors from a utility pole. One of the employees climbed the pole.
an employee was bending over inside a substation, measuring for an oil retention dike. As he stood up, the metal rod he was u
on september 16, 1996, employee #1 was backing a forklift away from a building when the forklift began to tip. Employee #1 trie
employee #1 and coworkers were erecting a wood chip bin at a sawmill. He was on a steel support beam reaching for a contain
at 2:30 p.m. on november 21, 1991, employee #1 and two coworkers were conducting exploratory drilling using an ideco back-i
employee #1 suffered acute ethanol intoxication, pulmonary edema, and congestion after inhaling paint fumes. He died of asph
kam corporation, a construction company in saipan, was contracted by hansae garment manufacturing to construct a 2 story em
the addition of a two story wood frame banquet room was being made onto an existing building. The top floor of the addition wa


                                                     Page 61
                                                          all


an employee was using a boom truck to lower a pump into a well. When the work was completed, the employee moved the boo
employee #1 was unloading a d-6c caterpillar tractor off a tilt lowboy trailer when the tractor slid off the trailer. The tractor was e
at approximately 2:30 a.m. on october 9, 1990, employee #1 had been assisting another employee in the plant cleanup while th
employee #1 was installing trim on the edge of a stairway landing. To access the landing, the employee ran a 2 in. by 8 in. by 1
employee #1 was instructed by his supervisor to go to an adjacent roof and pick up a piece of plywood to use as a windshield w
employee #1 entered an 18 in. diameter stainless steel pipe to grind and replace a bad weld. He went about 80 feet inside the p
employee #1 and a coworker were laying pipe in an unshored, unsloped trench of unspecified depth when approximately 20 ft o
employee #1 was inside a 180 ft diameter dome, greasing the pins on a kochring 6633 excavator bucket. A kenworth 10-wheel
employee #1, a state highway technician, was struck by a contractor's transfer truck as it was backing up. He suffered multiple
employee #1 was digging a hole for a signpost when he suffered an apparent heart attack and died.
four employees were setting a 17-foot-long smoke stack into place through the roof of a boiler room. Three of the employees w
an employee was getting ready to paint a lamppost. He was working from a 23-foot-high mobile scaffold. The scaffold did not h
an employee was getting ready to paint a lamppost. He was working from a 23-foot-high mobile scaffold. The scaffold did not h
a grove at-422 crane was being used to move a 3500-pound concrete precast panel. The crane operator swung the boom to hi
scaffold end brackets and materials hoist collapsed dropping the project superintendent 101 feet.
at approximately 11:15 a.m. on may 25, 1994, employee #1 was laying brick on seven-story building from a 21 ft 2 in. high work
at approximately 11:15 a.m. on april 26, 1994, employees #1 and #2 were elevating a marklift 100 aerial lift after stocking their
at approximately 11:15 a.m. on april 26, 1994, employees #1 and #2 were elevating a marklift 100 aerial lift after stocking their
employee #1, who was positioned in a boatswain chair, was preparing to enter a more than 200 ft chimney to insulate its open a
at the beginning of stabbing operations on a drilling rig, employee #1 fell from the stabbing board to the rig floor. He died.
an employee was using a jackhammer to break through some concrete. The jackhammer blade penetrated an underground po
an employee was installing metal braces on top of a 6.7-meter-high roof under construction. A metal piece he was holding cont
the employer and two employees were dismantling a windmill pump motor. The mast of the derrick they were using to lift the pu
two employees were assigned to perform maintenance work on the roof of a school gymnasium. One of the employees found a
employee #1 had stepped around a backhoe while it was in operation and began to shovel, by hand, dirt into a trench. The dirt
employee #1 was allegedly hit by a cable. He did not report an injury nor had any other coworkers witnessed an injury. Employe
at approximately 6:38 p.m. on september 10, 1992, employees #1, #2, and #3 were severely burned when they opened a vesse
at approximately 6:38 p.m. on september 10, 1992, employees #1, #2, and #3 were severely burned when they opened a vesse
at approximately 6:38 p.m. on september 10, 1992, employees #1, #2, and #3 were severely burned when they opened a vesse
employee #1 was assigned to clean the header bolts at the top of a reactor. The reactor was under a nitrogen purge. The vent
at approximately 11:50 a.m. on july 31, 1990, employee #1, a carpenter, was standing on a retaining wall guiding a concrete bu
at approximately 4:15 p.m. on september 21, 1991, employee #1 was loading a caterpillar crawler tractor onto a flatbed trailer.
at approximately 2:30 p.m. on june 24, 1992, employee #1 was operating the stop/slow sign. The pilot car had just left and was
employee #1 was installing sheet metal roofing over insulation board. He misjudged where the roof sheeting lay and stepped th
employee #1 was apparently taking measurements on a balcony when he backed off and fell 9 ft 6 in. onto concrete. He was ki
on the morning of january 14, 1992, a contractor was replacing an underground sewer line. A crew of five arrived at work. Two
employee #1, a member of a five-man maintenance team, was employed to identify and repair leaks on an ocdee flume, which
at approximately 10:22 a.m. on january 8, 1994, employee #1 and a coworker were working on a monorail support system on th
at approximately 8:19 p.m. on august 14, 1994, employee #1, a boilermaker foreman, was working from a specialty suspension
at approximately 5:45 on june 30, 1992, employee #1 reported to work. Between 6:00 and 6:15, he was seen falling to the grou
a four-person crew was moving a pallet supporting a pump motor to a different location so that a sea container could be placed
on or about april 24, 1994, employee #1, a crane operator, was dismantling the boom of a crane. He was underneath the interm
employee #1, who was working in a trench that was not properly sloped nor shored, was killed when the trench caved in.
a crew of employees for an electric cooperative had completed installation of an electrical service to a residence. After the com
employee #1 was working at his assigned duties when he said he felt sick and was going home. About 30 minutes later he was
on or about may 9, 1991, employee #1 was working in the bottom of a trench approximately 20 feet deep, 10 to 12 feet wide at
an employee was working as a laborer on an underground pipe laying project. The laborer was standing on the ground, outside
on december 2, 1991, employee #1 was approximately 25 ft above the ground painting the fascia on a house. The ladder he wa
employee #1 was laying a sanitary line in a trench. The trench, which was 20 to 22 feet deep, was unprotected and caved in. Em
employee #1 and a coworker were performing maintenance work on an elevator. Employee #1 was in the elevator pit standing
at approximately 11:44 p.m. on september 19, 1992, employee #1 was welding a girder attached to a bridge pier. He fell approx
employee #1 was working at a height of 30 ft receiving steel joists from a crane. The crane used a pendulum motion to swing th


                                                       Page 62
                                                        all


an employee engaged in the scraping of an underground gasoline storage tank applied his oxy-acetylene torch to the tank and
at approximately 8:24 a.m. on november 18, 1991, employee #1 was operating a john deere crawler loader, model #ch0250x09
an employee was sandblasting the undersurface of the structure for an elevated train. During the operation, the employee conta
a carpenter was moving a 30-foot extension ladder. The earth where he was carrying the ladder was slippery. A 7200-volt overh
an employee was working with an air conditioning installer as a helper. He had not been trained in the electrical hazards he fac
a crew was installing aluminum siding on a house. The aluminum ladder they were using contacted an overhead power line. On
a crew was installing aluminum siding on a house. The aluminum ladder they were using contacted an overhead power line. On
the driver of a loaded cement truck that weighed approximately 64,000 lb parked on top of a water valve vault and drew a samp
at approximately 1:25 p.m. on november 13, 1991, employee #1 was working as a flagman at a highway construction project on
on february 19, 1992, at approximately 12:20 pm, employee #1 was using a rigid pipe machine (model 400a) to thread a one in
a three-person crew was removing deenergized secondary conductors from a two-span section of overhead power line. During
employee #1, a forklift operator, was driving a truck during construction of a parking garage. While driving from the concrete po
employee #1, a forklift operator, was driving a truck during construction of a parking garage. While driving from the concrete po
a job site superintendent age 35 was killed as he fell froma bullnose/barrel type roof of 28 feet high. Victim was inspecting roof
employee #1 was helping to install standing-seam sheet metal roof decking. He was working at the outermost eaves when he f
employee #1 was a truck owner and the sole proprietor of a haulage company that he operated with his son as independent op
employee #1, a concrete truck driver, was standing at ground level when a 4 ft by 8 ft by 3/4 in. piece of plywood fell from the 9
during the demolition of a 5 story parking garage, employee #1 was holding a water hose used to keep the dust down. He was
the driver of company vehicle #1 was plowing snow on a public highway. Employee #1 in company vehicle #2 was approaching
employee #1 and a fellow ironworker were connecting a horizontal steel beam to an unsupported column. After the connection
employees #1 and a coworker were dismantling conveyor chutes and the associated steel framework on an incline conveyor. T
employee #1 fell from a ladder that was standing on a port roof platform. When the employee fell, both he and the ladder hit the
on august 24, 1993, employees #1 and #2 were dismantling a double-legged 150 foot rohn tower that was owned by a cable co
on august 24, 1993, employees #1 and #2 were dismantling a double-legged 150 foot rohn tower that was owned by a cable co
a power line crew was replacing the top circuit conductors on a double circuit overhead power line. They were replacing no. 2 a
employee #1 was crushed to death by a compactor at a landfill expansion project. Preliminary information shows that the emplo
employee #1 and three coworkers, who were being lowered in a personnel platform from a crane, lost radio contact after the sig
one electrician was electrocuted, and two others were burned at an electric power generation plant construction site. The accid
one electrician was electrocuted, and two others were burned at an electric power generation plant construction site. The accid
one electrician was electrocuted, and two others were burned at an electric power generation plant construction site. The accid
employee #1 had dumped a load of dirt in the dump area. He pulled his dump truck forward. Instead of leaving the dump site, h
employee #1 was driving out the top pins that connected a tower cap to a section of tower boom. When the top pins were remo
employee #1 was in a komatsu pc 180, 18 ton excavator, serial #0113. About half the length of the machine was on a bridge th
at approximately 4:00 p.m. on june 7, 1994, employee #1 was preparing to connect a pipe in a trench that was 10 ft deep by ap
employee #1, of e.h. hughes, was installing a plywood cover over a water discharge pipe. As he was walking to a pickup truck t
employee #1 was secured to an electric pole that was supported in three directions. The employee severed one of the tridirectio
employees #1 and #2 were driving on an abandoned strip mine access road in a flatbed truck loaded with bales of hay/straw wh
employees #1 and #2 were driving on an abandoned strip mine access road in a flatbed truck loaded with bales of hay/straw wh
a power line worker was removing an old j-hook from a utility pole. (The pole was an angle pole.) the employee was not using a
an employee was operating a 2000-pound roofers hoist on the roof of a seven-story building. He and his coworkers were loweri
employee #1 was flagging traffic on a 4 lane divided highway. A tractor trailer struck the rear of an automobile, forcing the autom
employees #1 and #2 were pulling an old static line through pulleys located at the top of a 75 foot high tower. The two men wer
employees #1 and #2 were pulling an old static line through pulleys located at the top of a 75 foot high tower. The two men wer
deceased was on the floor of church building while 9 wooden arches 35' in height were being erected. While the 9th arch was b
employee #1 was repairing the roof of a school gym. It was a barrel roof with numerous skylights. When employee #1 tripped a
#null#
employee #1 placed an aluminum ladder against an exterior apartment balcony railing located approximateely 17 feet above th
employee #1 was sandblasting structural steel on a bridge 60 ft above a river. The employee was not tied off, nor was he weari
employee #1 was installing metal plates (61 by 35 in. sheets) on a bridge when he slipped and fell 55 ft to the ground. Employe
employees #1 and #2 were raising a safety cable when the section of chimney scaffold they were working on fell 46 ft. They we
employees #1 and #2 were raising a safety cable when the section of chimney scaffold they were working on fell 46 ft. They we
employee #1 was replacing concrete blocks from an outrigger platform on a tubular welded frame scaffold. The employee fell a


                                                     Page 63
                                                         all


employee #1 climbed a structure column to the 50 ft high work level, where he encountered difficulty and fell 50 ft to the ground
employee #1 was using a 60 ft condor articulating boom lift, model 6066, to place plywood approximately 40 to 45 ft above grad
employee #1 was supervising the unloading of large pieces of electrical equipment called c.t. cabinets. These cabinets, made b
two employees were painting the underside of an elevated subway structure from a catenary scaffold. The scaffold, approximat
employee #1 and three coworkers were working on the roof of a 4 story high school. They relocated a two point suspension sca
at approximately 10 am on february 4, 1991, employee #1 was using a wheelbarrow to dump debris from a reroofing job into a
employee #1 had just moved a two point suspension scaffold. He was standing on the scaffold 38 ft above the ground and secu
at about 9:20 a.m. on march 12, 1990, employee #1, a traffic maintenance worker, was painting a traffic signal device from an a
employee #1 was using a thomas, model bh 108, backhoe to break up the ground for paving. The employee had moved the ba
employee #1 was using a 14 ft straight aluminum ladder to climb from the 14th floor terrace to the roof. The ladder twisted and
employee #1 was using a 14 ft straight aluminum ladder to climb from the 14th floor terrace to the roof. The ladder twisted and
employee #1 was standing underneath a scaffold getting tools. A coworker was standing on a higher scaffold, 50 ft above him,
employee #1, a repairman/maintenance man, was lubricating parts on top of an elevator while it was fully operational. A passen
at approximately 2:50 a.m. on march 11, 1992, employee #1, a laborer for audox construction corp., was working on the roadw
employee #1 and a coworker were working on a two-point suspension scaffold without safety belts, lifeline, or tie backs. They a
on july 14, 1994, employee #1, a telephone field technician, was in the backyard of an apartment building checking on and repa
employee #1 was installing dock piling support when he was struck on the head by a pile driving hammer cap. The employee w
employee #1 was changing a light bulb in an overhead fixture using a simon model mp-60 extendible boom aerial lift. The lift's b
on april 29, 1990, employee #1, a welder-boilermaker for a pennsylvania tank erection company, was installing the roof sheets
employees #1 and #2 were installing 6 in. Pvc pipe for a curtain drain around a septic system in an unshored and otherwise unp
employees #1 and #2 were installing 6 in. Pvc pipe for a curtain drain around a septic system in an unshored and otherwise unp
at approximately 2:15 p.m. on november 11, 1992, employee #1, a flagman with a paving crew on a high-speed, limited-access
at approximately 7:15 a.m. on december 4, 1992, employee #1 was cutting an 8 in. by 10 in. collar in a section of sheet metal d
employee #1 was working inside a trench more than 5 feet deep in class c type soil. The vertical face trench was not protected
at approximately 1:05 p.m. on april 21, 1994 , employee #1, while working as a delivery person for a steel erection company, ha
at approximately 4:30 p.m. on april 6, 1995, employee #1 was struck by the front part of the hood on a morbank eager beaver w
at approximately 2:00 p.m. on march 29, 1993, employee #1 and another laborer were installing a 16 ft by 16 ft wood protective
at approximately 2:30 p.m. on august 17, 1995, employee #1 was loading a heil dump truck with chunks of broken concrete. Th
at approximately 6:30 p.m. on march 27, 1996, employee #1, a foreman and truck driver, was preparing to move into position a
employee #1 was driving a truck on a steep road when he apparently lost control, turned over, and went down the hill. Employe
an employee was working alone in the field, replacing fuses on a transformer. Because the employee had failed to use proper l
on september 24, 1992, employee #1 fell 21 feet through an unguarded skylight opening during a built-up roofing operation. He
employees #1 through #3, part of a welding contractor's crew, were in a petroleum storage facility when a clogged section of pip
employees #1 through #3, part of a welding contractor's crew, were in a petroleum storage facility when a clogged section of pip
employees #1 through #3, part of a welding contractor's crew, were in a petroleum storage facility when a clogged section of pip
employee #1 was standing between the back of a water truck and the back of a drilling rig watching a drilling operation. The dri
employee #1 walked onto a wooden platform used for concrete forms on an overpass under construction. High winds pushed th
a three-person power line construction crew was working on the last job of the day. The crew was to install new hardware on a
employee #1 had been working on a road patching crew. He was standing on the running board on the passenger side of a che
on the east side of the job site, the employer was removing purlins from the damaged portion of a metal warehouse wall from a
employees #1 and #2 were assigned to adjust the setting on a level data pressure sensor that was mounted on top of a soybea
employees #1 and #2 were assigned to adjust the setting on a level data pressure sensor that was mounted on top of a soybea
employee #1 was a 16-year-old boy who was part of a crew that was readying a 60 to 70 foot long house for moving. Work cea
employee #1 was operating a caterpillar d8k bulldozer on a road building project. A worn high-pressure hydraulic line on the left
at 8:30 a.m., employee #1 was doing dirt work as a heavy equipment operator. While attempting to climb on a bulldozer, he suf
employee #1, a concrete finisher, was sandblasting on a highway under construction when a vehicle traveling at excessive spe
employee #1, a 37-year-old construction worker, was working in a 6 to 7 foot trench while a backhoe operator was digging at on
ee #1 had 4 or 5 yards of shale left in his 20 yard capacity dump trailer and was dumping it out prior to it being loaded with scra
employee #1 was killed when he fell from a roof.
a work crew raised a concrete cap to be placed onto a steel trestle. The total clearance was 34 inches between the top of the tr
a superintendent was directing a crane operator who was using his crane to unload beams from a flat bed truck and place them
employee #1 was one of two employees who were rolling out an insulation blanket and sticking it onto steel beams. When he m


                                                     Page 64
                                                          all


employee #1 was operating a caterpillar sheep foot vibratory soil compactor when he came too close to the edge of a 6 foot em
at approximately 12:40 p.m. on may 8, 1991, employee #1 was installing insulation from a roof that was approximately 20 feet a
two roofers were moving a ladder-vator from a building against which it was leaning. They moved the conveyor to a vertical pos
two roofers were moving a ladder-vator from a building against which it was leaning. They moved the conveyor to a vertical pos
on jan 11,1990, at approximately 11;35am, a broderson hydra-hammer mobile concrete breaker was being driven south on she
on feb 13th, 1990 at approximately 1;20pm. An employee was about to dismantle a ladder jack scaffold being used at the 28 fo
employee #1 was walking back to the work site from his car. He was run over by a dump truck that was backing up to the work
at approximately 7:48 a.m. on february 11, 1991, employee #1 was working on a steeply sloped roof (greater than 4:12). The di
employee #1, a laborer, and a coworker, a plumber, were working in a 5 ft deep trench installing an 18 in. diameter sewer pipe.
an employee had carried a 10-foot-long section of 12-inch-diameter culvert to a point immediately south of a backhoe being use
an employee was operating a concrete pumping truck directly beneath a 4800-volt overhead power line. The line was 32 feet ab
a painter was electrocuted while he was changing light bulbs.
according to sources at the scene, employee #1 had just left a job meeting and was walking toward his own dump truck. He wa
employee #1 was repairing an overhead door frame when the curtain fell on him, killing him.
at approximately 4:30 p.m. on october 10, 1991, employee #1 was working on the second floor of a newly constructed house. H
employee #1 and coworkers were using a directional drilling machine to run a drain line under the garden state parkway. The m
an electrician was installing electric conductors in a conduit. He was 8.5 meters above the ground on a grain bin. He apparently
employee #1 was uncovering blue top stakes when a caterpillar motor grader, model #140g, backed over him. He was killed.
employees were installing steel bar-joist on a steel structure when the structure collapsed, striking employees #1 and #2. Emplo
employees were installing steel bar-joist on a steel structure when the structure collapsed, striking employees #1 and #2. Emplo
victim (lineman) was working in a bucket a line truck attaching electrical conductors to a wooden pole that had existing energize
an employee was raising a core drilling rig into drilling position. The drill rig contacted a 115-kilovolt overhead power line, electro
employee #1 was placing roof tie-down devices (clips) for other employees who were placing seam decking. He was returning w
employees were working 16 ft 6 in. above the ground on the roof of a warehouse building under construction. The beams and in
on or about june 15, 1989, employee #1 was operating on a 1986 john deere tractor, model 3t90t-j, style #1050, equipped with
on june 21,1990, employee #1 and coworkers were installing ducts in a newly erected dust collection system. Employee #1, a jo
at about 3:00 p.m. on october 24, 1990, employees #1 and #2 were installing concrete storm sewer pipe in a trench that was 75
at about 3:00 p.m. on october 24, 1990, employees #1 and #2 were installing concrete storm sewer pipe in a trench that was 75
on january 14,1991 at approximately 11:50am a five man crew was performing a power line pole change out operation, they ha
two power line workers (one of whom was a foreman) went to a substation with orders to open an oil circuit recloser. The reclos
employee #1 was clearing 20ft metal pipe tjat was hung up in some fallen trees. Pipe was to be loaded on flatbed trailer. Pipe w
at approximately 4:00 p.m. on june 21, 1991, employee #1, a carpenter, was working from a 19 in. wide board on a mobile scaf
at approximately 8:00 a.m. on april 24, 1990, a high loader traveled up a hill to deliver equipment that was being carried in its fr
employee #1 was removing sections of roof sheeting that had been temporarily set the previous evening to protect the insulatio
two employees were using lacquer thinner to wash stains off a bar. After the stain was removed, the employees went upstairs f
employee #1 was told to climb onto the weather type tower on a planked morgan scaffold. He was helping position an 18 ft sec
at approximately 11:00 a.m. on january 29, 1990, employee #1, a general laborer, was working in a septic system trench that w
at approximately 10:10 a.m. on april 3, 1990, employees #1 and #2 were carrying a 20 ft length of 6 in. Pvc pipe along a 36 ft lo
employee #1 was standing under a spider that was hoisting a workman and three metal ladder sections up a scaffold. The ladd
employee #1 was attempting to pull a wooden light pole from the ground using a cherry picker-type personnel hoist. The rope b
a power line worker was splicing an overhead power line that was supposed to be deenergized. The employee was electrocute
employee #1 was helping to set a precast concrete beam into place. The beam fell from its support and onto him. Employee #1
at approximately 9:00 a.m. on march 15, 1991, employee #1, the foreman of a crew installing decking on an a-frame roof, was
employee #1 was driving a crane back to a work area after lunch. He drove the left front wheel off the road onto a wooden pier.
employee #1 was part of a crew that was dismantling a shoring scaffold. He removed the hook attaching his safety belt and lan
employee #1 and two coworkers were erecting a scaffold system by installing platforms between two mobile scaffolds. Three p
employee #1 was removing boards from the roof of a building. He picked up a board that had just been unsecured and was ma
employee #1 and two coworkers were assigned the task of increasing the distance between the tops of 44 ft form columns. Em
employee #1 was demolishing brick veneer from the outside wall of a dormitory at the norfolk naval yard in portsmouth, va. Wh
An employee was struck by a trailer as it was being backed up. the driver of the trailer was backing the trailer up so that he cou
employee #1 entered a confined space to remove a bypass hose. When he detached the hose, sewage and waste water enter
employee #1 entered a confined space to remove a bypass hose. When he detached the hose, sewage and waste water enter


                                                       Page 65
                                                         all


employee #1 entered a confined space to remove a bypass hose. When he detached the hose, sewage and waste water enter
employee #1 entered a confined space to remove a bypass hose. When he detached the hose, sewage and waste water enter
employee #1 apparently was backing a wheel loader with the mast elevated. The mast apparently hit the top of a water tank an
employees were drilling holes in preparation for blasting nearby with explosives when the dynamite prematurely exploded. Emp
employees were drilling holes in preparation for blasting nearby with explosives when the dynamite prematurely exploded. Emp
employees were drilling holes in preparation for blasting nearby with explosives when the dynamite prematurely exploded. Emp
employees were drilling holes in preparation for blasting nearby with explosives when the dynamite prematurely exploded. Emp
an employee was working from the bucket of a hi-ranger articulating-boom aerial lift that was mounted on a ford truck. The emp
employee #1 working with another employee on the 3rd deck area of a football stadium addition at an elevation of 63'-5" above
employee #1, working from the roof monitor on an existing building 36 1/2 ft above the concrete floor, was installing insulated a
employee #1, an inexperienced laborer, went to a site alone with a truck and tilt bed trailer to pick up a 1954 farm tractor with a
three employees were removing old roofing from a two-story residential farm house as part of a roofing project. They had been
three employees were removing old roofing from a two-story residential farm house as part of a roofing project. They had been
employee #1 was working from an unguarded plank on a scaffold about 11 ft off the floor. He fell from the scaffold and landed o
a farmer had knocked down a utility pole at the intersection of a state road and a county road. The electric utility was called to r
on 2/21/90 at approximately 7:20 am an employee of doone electric co fell through an opening on the working platform in the m
employee #1 was installing corrugated roof decking on the roof of a building. He slipped at the leading edge of the roof and fell
employee #1 was working from a two point suspension scaffold approximately 30 ft above a road under a railroad bridge. Empl
after complaining of chest pain for some time, employee #1 collapsed and died while digging a shallow hole in a petroleum fuel
employees #1 and #2 entered a concrete cistern for unknown reasons. They were overcome by hydrogen sulfide gas and died
employees #1 and #2 entered a concrete cistern for unknown reasons. They were overcome by hydrogen sulfide gas and died
an employee was using a ladder to access a lower roof area. An electrical service was located in this area. The employee was
employee #1 was cleaning sand residue from the bottom of a 10,000 gal gasoline tank with a shop-vac in preparation for placin
three employees (the sole owner of a company and both its employees) had just finished repairing a metal roof on an agricultur
three employees (the sole owner of a company and both its employees) had just finished repairing a metal roof on an agricultur
three employees (the sole owner of a company and both its employees) had just finished repairing a metal roof on an agricultur
an excavation approximately 3 ft wide by 15 ft long by 13 ft deep was dug in clay ground to make a sewer repair. Employee #1
employee #1, the foreman, was installing steel roof decking with three coworkers. He was walking within 6 to 8 in. of the roof ed
an employee was installing a transformer on a new 40-foot, class 3 utility pole. The 7200-volt primary overhead power line on th
employee #1, a truck driver, was offloading sand from a small dump truck. For some reason, he climbed up on the truck frame
employee #1 and several coworkers were doing demolition work in a refinery, removing components of an old iso cracker proce
employee #1, the foreman, and another employee were digging a 10 foot deep trench across a state highway. The power shove
an employee was removing a ceiling tile. The metallic grid supporting the ceiling tiles was energized by an unknown source. Th
employee #1, a truck driver, had finished loading a milling machine onto his flatbed trailer and was preparing to drive away. The
at approximately 12:50 p.m. on february 16, 1996, employee #1 and a coworker were installing metal roof panels on a covered
at approximately 4:00 p.m. on march 6, 1996, employee #1 was using an american model 9270 crawler crane to move four pie
on march 17, 1994, employee #1 called in sick to work. Late on sunday, march 20, 1994, he was found passed out in the backy
at 8:00 a.m., employee #1 and coworkers arrived at the worksite knowing they had to finish by 4:30 p.m. during the morning, em
at 11:45 a.m. on march 2, 1990, employee #1, a company superintendent, was installing kilns at a sawmill under construction. T
some employees were using a truck-mounted crane to lift a microwave tower into place. One of the employees was walking the
employee #1 and two coworkers were erecting a microwave tower. Employee #1 was at the 110 ft level acting as a spotter for t
an employee was preparing a steel pipe bridge for connection between two buildings. The work crew was using a crane to lift th
employee #1 was standing at the east end of his tampo roller, filling it with water. His back was toward the west end of the dyna
the employer was building a concrete reinforced bridge, replacing an older steel bridge over a large ditch alongside a levee. Em
at approximately 11:45 a.m. on september 29, 1995, employee #1 and a coworker were laying sewer pipe in a trench that was
three roofers were installing a roof. One worker was on the ground getting shingles, while employee #1 and the other roofer we
at approximately 2:45 p.m. on june 20, 1990, four employees were attempting to raise the gantry on a manitowoc 3900w crane.
employee #1 was taking inventory of the air units above the false ceiling in room 301, horton field house, illinois state university
employee #1 had been sitting on a bank of dirt and moved to a position just behind a backhoe that was in operation. The backh
at approximately 2:00 p.m. on august 24, 1990, employee #1 and a coworker had removed a 3 1/2 foot by 4 1/2 foot section of
employee #1 was driving an earthmover/scraper. He had completed unloading at the stockpile and was returning for another lo
employee #1 was "shooting the grade" on a highway project. He stepped onto the highway, unseen by the driver of a nearby tru


                                                      Page 66
                                                          all


three employees were attempting to disassemble a section of a crane boom. The boom was parallel to the ground and about 5
employee #1 was standing in front of his scraper with his back to the scraper parked in front. To move out of line, the operator o
employee #1 was standing on the truckbed of a truck-mounted crane while a waxed cardboard container was being removed fr
employee #1 was setting up to refuel a track-mounted hydraulic excavator from a 100 gallon fuel tank on the back of his truck.
employee #1 went either over or under an improper guardrail at an elevator shaft. He apparently chose to throw his welding lea
employee #1 stepped into a lane of traffic and was struck in the chest by a camper support pole that was on a pickup truck. He
employee #1 was lighting the pilot light on a boiler when an accumulation of gas exploded. He was partially decapitated and kill
employee #1 was working in a vehicle-mounted elevating and rotating aerial device. He was hanging banners in a civic center e
employee #1 was climbing a 280 ft high communication tower using step bolts on the leg of one of the towers when he fell from
employee #1 was loading a crawler tractor (bulldozer) onto a flatbed trailer that was parked on sloped ground. The tractor tippe
a koehring 6644 hoe was digging a 3 ft deep trench in rock and shale at a shopping plaza under construction to install an 8 in. P
a power line crew was working on a 120-volt overhead power line. It had just rained, and the working conditions were wet or da
employee #1, who was working from an open-sided scaffold, fell approximately 33 feet to the concrete sidewalk. He sustained
an employee was riding on top of a house being moved from one site to another. At one point, the house had to pass beneath a
employee #1 was laying storm sewer line in an 11 ft deep trench when the trench wall collapsed, trapping him under the dirt an
employee #1 was reviewing blueprints with his foreman and crew. When he turned to retrieve a paper that he had dropped, em
employees were assigned to walk across and work from an unsafe, temporarily supported walkway (catwalk) without any form
employee #1 was working on the third level of a building renovation project when he fell through an inadequately guarded eleva
the employees were walking on the purlins attached to the wooden trusses of a 24 foot high building under construction. They w
at approximately 9:30 a.m. on may 23, 1991, employee #1 finished digging a small trench and left the area by driving around th
at approximately 12:45 p.m. on july 9, 1991, employee #1 was placing a steel sheet roofing panel at the apex of a roof when he
on october 28, 1991, employee #1 was backing a roller upgrade along the berm. The roller tipped over and the employee either
four employees were detailing the roof of a steel structure. Three of the employees were on the structure of the roof when a pie
four employees were detailing the roof of a steel structure. Three of the employees were on the structure of the roof when a pie
employee #1 was operating a paving roller/compactor. The roller overturned, and employee #1 was crushed and killed.
an employee was regulating the dumping of gravel out of a chute at the back of a dump truck. The gravel was being placed in a
employee #1 and a coworker were working around a 5 foot 3 1/2 inch by 8 foot 3 1/4 inch floor opening when employee #1 fell t
a 32-year-old concrete finisher was brushing concrete with an 18-foot-long magnesium bull float handle attached to a 2-foot-wid
an employee was handling a 2-inch-by-4-inch piece of metal. The metal contacted a 75-kilovolt overhead power line, and the em
employee #1, the operator of a case 580 super k turbo loader backhoe, was preparing to replace a broken swing cam bolt while
an employee was operating a skyhook crane to move steel beams that were stored directly beneath a 7200-volt-to-ground over
employee #1, a flag person, was directing traffic when he was hit by a passing vehicle. He was killed.
employees #1 through #3 were dismantling a temporary bridge that was used while their company erected a new bridge. The te
employees #1 through #3 were dismantling a temporary bridge that was used while their company erected a new bridge. The te
employees #1 through #3 were dismantling a temporary bridge that was used while their company erected a new bridge. The te
employee #1 was the owner of a loader that was involved in a fatal accident. When he saw the injured employee on the ground
at approximately 7:25 a.m. on august 8, 1994, employee #1 was driving a john deere 290d excavator onto a lowbed trailer. The
employee #1 died of acute renal failure.
on november 30, 1994, employee #1 was digging a trench 3 ft deep by 1 ft wide along the base of a cracked and leaning concr
employee #1, a mason, was laying concrete blocks for the foundation of a retail store. The estimated heat stress reading for the
the employee was operating a john deere skid-steer loader with the guard missing on the right side of the operator position. A s
employee #1 was assigned to apply a waterproofing priming material containing methyl chloroform and 1,4-dioxane to the foun
employee #1 and a coworker were on a wood scaffold that was 21 feet above the ground. As one employee walked toward the
employee #1 was killed when heavy equipment fell on him.
employee #1 was standing on the tracks of a dozer while it was running. The dozer apparently jumped into reverse gear and em
employee #1, the co-owner of a barging operation, was on an unloading site supervising the refloating of a grounded barge at h
at about 10:30 a.m. on december 8, 1990, three employees were handling a concrete form that was going to be placed. When
at about 10:30 a.m. on december 8, 1990, three employees were handling a concrete form that was going to be placed. When
at about 10:30 a.m. on december 8, 1990, three employees were handling a concrete form that was going to be placed. When
employee #1 was removing bolts for the subsequent removal of skylight glass sections. The skylights covered over 100 ft of the
a communications worker was in an aerial lift using an electric drill to drill holes in a utility pole. The drill was powered by a truck
at approximately 1:45 p.m. on february 17, 1992, employee #1 was on a hammer head tower crane boom helping dismantle the


                                                       Page 67
                                                         all


employee #1 was working from a floating platform to install a water line underneath a pier. Coworkers heard him calling from un
employee #1 was attempting to step across a 4 ft gap between horizontal structural beams and a tubular welded scaffold. It app
employee #1, the owner of a construction company, was installing or removing toeholds on an icy roof. He sustained multiple fr
at approximately 11:45 a.m. on october 9, 1990, employee #1, an apprentice carpenter, was helping the foreman and a cowork
at approximately 10:30 a.m. on september 21, 1990, employee #1 was using an 11 1/2 ton link belt crawler crane to lower a bo
employee #1 was attempting to replace the front right side leg/spring on a model r-600 mack dump truck. He placed a railroad
a concrete pumper truck was being used to fill concrete forms. The boom from the pumper contacted an overhead power line a
employee #1 fell from an unguarded scaffold, struck his head, and died.
employee #1 and coworkers were unloading reinforcing bar steel from a truck onto the deck of a bridge that was being rebuilt. H
employee #1, a sandblaster for a bridge painting contractor, was crossing a major highway at night to check recycler equipmen
employee #1, a 71-year-old self-employed mason, fell, striking his abdomen against an object. He died of asphyxia. No jurisdic
employee #1 was removing a section of pipe while working within an approximately 75 ft high by 4 ft diameter standpipe that wa
a rubber-tired payloader, operated by employee #1, was seen by three coworkers bouncing down an approximately 15 degree s
employee #1 was working from a scaffold that had been erected for a church steeple. He fell 30 ft from the scaffold to the churc
employee #1, a roofing foreman, had mopped hot tar on a flat roof so that a coworker could apply 4 by 4 ft sheets of insulation.
employee #1 was using a caterpillar 6-wheel dump truck to haul excavated material to a dump site on the next level up a moun
at approximately 11:30 a.m. on june 24, 1993, employee #1 was placing traffic cones on interstate i-65, at the cullman exit and
employee #1 was bulldozing a hill on a roadway. He was about 60 ft above the haul road of the new roadway, backing upgrade
two employees were placing a 30-foot-long wooden light pole on the bank of a ditch. The pole was suspended from an 18-ton g
employee #1 was burning a ladder and cage off a 55 gallon paint storage tank that had been damaged during a fire. The emplo
employee #1 was walking toward a service truck that was backing up. He was struck by the truck and run over by its rear whee
employee #1 was a motor grader operator who had been released by his employer to take a rest. The wahco motor grader, ser
at approximately 1:05 p.m. on july 11, 1990, employee #1 was working underground in a rainstorm tunnel. When rain flooded th
employee #1 had been mixing a three part epoxy mixture that would be applied to concrete. At approximately 3:15 p.m. on aug
two employees were unloading and storing tools and equipment at the end of a work day. They were walking toward an office/s
two employees were unloading and storing tools and equipment at the end of a work day. They were walking toward an office/s
at approximately 11:15 a.m. on november 26, 1990, employee #1 was preparing to lay a length of sewer pipe in a trench that w
employee #1was backing a lull machine across a roadway. As he turned, the back wheel went over the edge of a draining ditch
a track crane was being moved from one pile driving location to another by walking the crane. The foreman was walking in fron
employee #1 was killed when he fell 30 feet from his work area. It is not known whether he fell off a work ladder or the roof.
at approximately 7:30 a.m. on january 10, 1990, employee #1 was using a ground-mounted drum hoist to lift a pan of cement to
employee #1, the bomag roller compactor operator, failed to turn off the ignition as he was dismounting from the operator's plat
at approximately 5:15 p.m. on march 5, 1991, employee #1 was preparing to weld slab supports onto a precast concrete slab th
while pulling vegetation (trees, limbs, etc.) up onto a roadway, employee #1 stepped into the side of a semi-trailer and was run
employee #1 was on a second floor, tack welding a metal sub-floor into place. He walked to the north side of the floor that he h
three employees were installing a large metal sign at a service station. The sign was hoisted by a 100-foot skyhook crane. Two
three employees were installing a large metal sign at a service station. The sign was hoisted by a 100-foot skyhook crane. Two
employee #1 was on a ladder when he unsecured a cable. The cable fell, striking the employee and knocking him off the ladde
employee #1 was in a trench with near-vertical banks when the walls caved in. He was killed.
employee #1 walked toward the edge of a roof and fell 21 ft head first. He died.
some employees were blasting under an overhead power line. When a charge was set off, the blasting cap wires and lead wire
employee #1 got out of his truck cab to check on the raised dump truck bed. He went under the raised load without putting the
at 1:00 p.m. on july 30, 1992, employee #1 was driving a wheel tractor out of a forest where he had just driven fence posts on a
at approximately 12:35 p.m. on september 12, 1990, employee #1 was proceeding down an old timber skid road operating a cr
a road crew was chip sealing a two-lane, level stretch of gravel road that has a slight incline, a forest on the south side, and a 1
employee #1 and a coworker, both carpenters, were framing a stud wall on the second floor of a house. The wall was lying on t
employee #1, a grader operator, and two coworkers were involved in the construction of a roadway. Employee #1 and the site s
employees #1 and #2 were placing bundles of steel decking on the skeleton steel of a warehouse structure. After they had plac
employees #1 and #2 were placing bundles of steel decking on the skeleton steel of a warehouse structure. After they had plac
employee #1 was constructing an access road/platform for drill rigs in an iced-over reservoir (12 in. to 18 in. of ice). Employee #
a crane operator, a saw shop foreman, and a mechanic were under a crane, removing an inspection plate so that the cutting do
employee #1 was tearing down the log walls of a burned out single-story log home. The roof, roof trusses, and rafters had been


                                                      Page 68
                                                        all


employee #1 was welding metal decking to the joists adjacent to the decking edge when he fell backward and dropped 15 ft on
at about 10:15 a.m. on october 24, 1991, employee #1 was removing debris from a roof. He carried the wood to the edge of the
employee #1 and a coworker were rigging a sky climber (single point scaffold) while atop a 140 ft bridge pier. Neither man conn
two employees were operating a 29-foot-high mobile drilling machine. One of them was walking behind the machine, operating
two employees were operating a 29-foot-high mobile drilling machine. One of them was walking behind the machine, operating
at approximately 8:00 a.m. on january 3, 1992, employee #1, a flagman, was assigned to flag traffic around a road widening op
employee #1 was crushed and killed in an excavation cave-in.
at approximately 8:30 a.m. on april 20, 1992, employee #1 jumped approximately 4 ft down from a roof to a two point suspensio
at approximately 8:30 a.m. on april 20, 1992, employee #1 jumped approximately 4 ft down from a roof to a two point suspensio
a sump pump was being lowered into an excavation by a crane. An equipment operator was positioning the sump pump when t
employee #1 was installing vinyl siding onto a single family home from a pump jack scaffold when he fell into the 1 1/2 to 2 ft sp
employee #1 was operating a concrete cutting saw with all the proper safety equipment when he was struck and killed by an ou
employee #1, an iron worker, was measuring a steel beam on the second level of a 2-story tiered building for the layout of bar j
on november 8, 1993, employee #1, a diver, was part of a 3-man dive team, which also included the person in charge and the t
a sanitary sewer renovation project was progressing through a cut in a street. The trench had been sloped back at 1/2:1, excep
employee #1, a roofer, was sealing rubber sheeting on a 2 ft by 4 ft roof opening before a ventilation system was installed. He f
on july 10, 1995, shortly after beginning work, employee #1 began complaining of severe chest pains. Ems arrived and adminis
a three-person power line crew was restoring electric power to a residence after a rainstorm. The crew arrived at the residence
employee #1 was welding in a kneeling position when he suffered a fatal heart attack.
employee # was attempting to knock concrete off fence poles when he dropped to his knees. Attempts were made to revive him
two bricklayers were building a block wall. One of the employees (employee #1) had been working with the company for about
two bricklayers were building a block wall. One of the employees (employee #1) had been working with the company for about
employee #1 was climbing from a platform to an expansion joint assembly on a bridge and fell approximately 31 ft to the rocks.
on december 6, 1995, employees #1 and #2 were installing a microwave antenna dish on a communication tower. It was 3:50 p
on december 6, 1995, employees #1 and #2 were installing a microwave antenna dish on a communication tower. It was 3:50 p
employees #1, #2, and #3 and three coworkers, who worked for a masonry contractor, were on scaffolds erected at the lower p
employees #1, #2, and #3 and three coworkers, who worked for a masonry contractor, were on scaffolds erected at the lower p
employees #1, #2, and #3 and three coworkers, who worked for a masonry contractor, were on scaffolds erected at the lower p
two employees were guiding a mobile scaffold as it was being moved into position by a bobcat. The scaffold had platform stage
two employees were guiding a mobile scaffold as it was being moved into position by a bobcat. The scaffold had platform stage
employee #1 was performing a sewer line tap from a residential home. The employee was the owner and operator of the comp
employee #1 and a coworker were working from a two-point suspension scaffold when the left winch lost its grip on the wire rop
a material handling fork truck was being used to move a 40 foot long by 6 foot 5 inch wide stainless steel boning table. The fork
an employee was painting an outside wall that was 10 feet, 10 inches high. The employee was walking on top of the wall, which
two plumbers employed by a plumbing contractor were working at a single-family dwelling. They were unclogging a kitchen was
employee #1 was caught and run over by a backhoe that was rolling backward. He was trying to get out of its path. Employee #
employee #1 was building a work platform on scaffolding inside an elevator shaft when he fell approximately 28 feet to the conc
employees who normally performed concrete work were working on a spud barge that was spudded with two spuds on one side
employee #1 was the engineer responsible for the mechanical equipment on board the barge "weeks 551." when the closing w
at approximately 8:40 a.m. on september 17, 1990, employee #1 was in a trench that was one block long by 4 ft wide by 8 ft de
on september 4, 1991, employee #1, an asphalt tester, was kneeling with his back to a semi-tractor-trailer rig with a belly dump
on july 23, 1991, employees #1 and #2 were helping to disassemble an asphalt plant. They were at a height of approximately 1
on july 23, 1991, employees #1 and #2 were helping to disassemble an asphalt plant. They were at a height of approximately 1
the employee was in the process of securing metal trench walls. The worker was at the bottom of a 7' trench (depth) 5' (wide) a
employee #1 had been wall plastering while standing on three planks without railings at the 24 ft level of a tubular welded scaffo
employees #1 and #2 were cleaning and patching the expansion joints between concrete slabs in the road. The employees wer
employees #1 and #2 were cleaning and patching the expansion joints between concrete slabs in the road. The employees wer
two employees were installing an overhead light in a closet on the eighth floor of a building under construction. One of the two,
on may 15, 1995, j and r construction company was building a golden corral restaurant in clinton, nc. j and r construction person
employee #1, an iron worker, fell from a metal deck while spot welding. According to a witness, employee #1 was working near
employee #1 and a coworker, an equipment operator, were setting manholes at a construction site. Employee #1 was standing
richard hunter was in the process of bracing concrete block walls in a sewer trench in preparation to pour concrete for the floor


                                                     Page 69
                                                         all


employee #1 fell approximately 36 feet from the third floor elevator opening into the open shaft to his death. There were no witn
employee #1, a welder's helper, was helping employee #2 weld the remaining nipple onto a gas flow line that would be hooked
employee #1, a welder's helper, was helping employee #2 weld the remaining nipple onto a gas flow line that would be hooked
on october 10, 1991, employee #1, a pipeline supervisor overseeing the connection of a gas sales line and a gas flow line to a s
employees were connecting a gas flow line and a gas sales line to a separator unit. While the employee welded the remaining n
employee #1 was working from a folded 6-ft stepladder on top of a dust collector system. He may have lost his balance or the la
on august 29, 1996, employee #1 was using a john deere 664g front end loader to carry some 4 ft by 12 ft crane outrigger pads
employee #1 and a coworker, of creative builders, iglewood, ca, were assigned to unearth a perforated pipe drain buried behind
employees #1 through #5 were struck by falling steel beams when a bridge collapsed. Employees #1 and #2 were killed, and em
employees #1 through #5 were struck by falling steel beams when a bridge collapsed. Employees #1 and #2 were killed, and em
employees #1 through #5 were struck by falling steel beams when a bridge collapsed. Employees #1 and #2 were killed, and em
employees #1 through #5 were struck by falling steel beams when a bridge collapsed. Employees #1 and #2 were killed, and em
employees #1 through #5 were struck by falling steel beams when a bridge collapsed. Employees #1 and #2 were killed, and em
the employee, bernard b. blanton, was crushed to death while dismantling a crane boom on a truck-mounted crane.
Stuck by pieces of equipment.
at the northwest remote control gate, employee #1 was fatally injured from an accident that occurred on 07/04/98 at approxima
On January 05, 2001, at approximately 10:00 a.m., the President of Safety Counselling Inc., notified the New Mexico Occupatio
the company was in the process of demolishing a building. The walls had been removed. The concrete roof was supported by s
the company was in the process of demolishing a building. The walls had been removed. The concrete roof was supported by s
An employee who was replacing a bearing in exhaust was found dead on the floor at approximately 2:00 pm on 09/13/00 at 141
Employee fell from the 340' elevation of a telecommunication tower. The employee was not properly trained and was not tied of
An excavator was lifting a load of dirt with a container when the hydraulic line broke,causing the bucket to fail, striking an emplo
employee #1, a subcontractor, was using a tractor-driven auger to drill holes for a poultry house. Earlier, the employer had remo
employee #1, a contractor, was in a rush to complete the entryway of a building. From his home office he retrieved various scaf
employee #1 was on the fourth or fifth rung of a 10 ft fiberglass stepladder. He was using hand tools to remove wooden forms f
An employee was fataly injured while unhooking a 20 foot hudson trailer from the rear of a two ton ford truck. The trailer was lo
employee fell from 240 foot communications tower.
employee conducting steel erection fell 25'9" from floor decking, this fall resulted in a workplace fatality.
On or about 05/05/00 victim one was in the process of burning off a brush pile accumulated from the clearing of a plot of land fo
at approximately 11:40 a.m. on may 17, 1996, employee #1, of blake construction co., inc., fell 16.5 ft through a floor opening o
on july 19, 1996, employee #1 was installing beams for an above-ground conveyor system under construction. When pressure
on april 7, 1997, employee #1 was working on the second floor of the wingate inn motel construction site. After concrete floor sl

on 04/23/97 four employees were tasked to dismantle a scaffold and moved it to the east side of the building. The scaffold was
on 04/23/97 four employees were tasked to dismantle a scaffold and moved it to the east side of the building. The scaffold was
employee #1 was killed when run over by a crawler-type tractor/loader.
employee #1 fell from a scaffold and was killed.
the deceased and another employee were two apprentice linemen who were assigned the task of installing a grounding protect
Employee fell out of bucket.
the victim had been hired by this tower erection contractor to be the tower erection foreman. His, and the rest of the crew's, firs
employee #1 was working in a 4 ft 6 in. deep by 30 ft long by 11 ft wide trench that ran alongside a 4 ft wide concrete sidewalk i
on 8/20/98 at approximately 11:30 pm, employee #1 was clearing trash and wooden pallets off the roof where his company was
employee #1 was putting christmas lights on the leading edge of a house roof when he fell from the roof or the extension ladde
employees was tighten bolts on rafters straps to a boat house. Employee was on scaffold boards and fell approximately 9' (nine
two employees were attempting to reach an opening to be closed (tarped) to prevent overspray fire proofing overspray from rea
on 11 december 1997, the victim was killed in an excavation located at 26th & mason, omaha, nebraska. Through interview sta
at approximately 7:17 a.m. on may 29, 1997, employee #1 was driving a caterpillar d400 articulating dump truck down a haul ro
employee #1 was marking the 6-in-12 roof of a two-story house before installing new shingles. He slipped and fell approximatel
no abstract available
csho did not enter abstract
head & internal trauma in full arrest
On 1-11-00 a construction accident occurred when employee #1 was working in an excavation which was approximately 8 feet


                                                      Page 70
                                                         all


Injured employee (Employee #1)was working on a closed down lane on the freeway. Employee #1 was standing on a rack whic
around 12:05pm an employee (owner/operator) was working from a scissor lift taping drywall. Employee fell 12 feet to his death
propane gas explosion. On 8/24/99 a residential home was nearing final completion when a gas (propane) leak occurred. The h
employee was ran over by construction equipment
on june 26,1997, david l. marshall, age 36 was fatality injured when he fell about 12 feet from a ladder at a business called che
Employee #1 was gloving from a pole, connecting an engergized line (7200 kva) with a preform. Employee #1 was positioned h
employee #1, a construction worker, was shot and killed.
diver caught in cofferdam, where he drowned.
employee #1 was removing stucco when he fell approximately 26 ft off the scaffold and was killed. He was working as a volunte
on december 15, 1995, employee #1, of cooper steel company, inc., was repositioning himself on a steel girder to receive an 85
hoisting chiller tank when rigging chain broke causing tank to fall and roll pinning employee between tank and concrete block w
On July 26, 2000 at approximately 10:50 a.m., the San Francisco District Office of DOSH was notified of a fatality at a roofing c
at approximately 11:30 a.m. on august 9, 1996, employee #1, of st. John's roofing company, fell 21 ft through a 4-by-4 skylight
on january 29, 1998 at approximately 2:04 p.m., a telecommunications employee was fatally injured when he fell approximately
on 8-12-99 employee #1 was operating a post-tensioning device on a concrete slab. Employee #1 was releasing the pressure o
on 8-18-99 at 1500, an accident occurred at 9500 gilman drive, san diego, ca at the uscd chemistry building which is under con
at approximately 12:00 noon on july 26, 1996, employees #1 and #2 were working on the roof of a two-story building in brawley
at approximately 12:00 noon on july 26, 1996, employees #1 and #2 were working on the roof of a two-story building in brawley
employee no. 3.1, a full time employee of 4 seasons roofing, was working on the roof of the building 7766 w. hollywood blvd., la
During a cross arm utility pole change and line upgrade, the mack jumper became energized. The victim made contact with the
an employee had climbed a utility pole without properly testing it beforehand. The pole was rotted and insect infested below gro
Front-end loader Driver 20-30 embankment into gravel-pit, flipping upside an crushing victim inside. On 5-26-2000 at approxim
at 7:45 a.m., employee #1, a carpenter, reported for work to woodinville, wa. He worked until break time, approximately 10:15 a
employee #1, of one-way construction, was engaged in emergency bridge repairs for the burlington railroad. His superintenden
an electrician and his apprentice were replacing 277-volt conductors supplying an overhead light for a building. (The wiring had
on april 10, 1995, employee #1 and a coworker were installing electrical switches and faceplates on a house. Employee #1 was
employee #1 was standing on an aluminum extension ladder in good working condition that was leaning against a 9 foot high ro
employee #1 collapsed on a construction job site and died after suffering a heart attack.
employee #1 was a passenger in a vehicle when it rolled over on the highway. He was ejected from the vehicle and killed.
on november 2, 1995, employee #1, a carpenter for fosback construction, fell approximately 17 ft through a railing onto concret
50 year old male steel erector fell approximately 12 feet from roof to concrete. Later died from complications of multiple injuries
at approximately 4:00 p.m. on november 4, 1996, employee #1, of vern w. johnson and sons, inc., was struck by a motor vehicl
on 4/21/98 the victim fell from an unknown elevation to a concrete surface suffering massive trauma to his head. He was found
on 05/08/98 at approximately 9:00am victim #1 collapsed while tamping concrete. Co-workers started cpr until arrival of colfax r
on august 19th at approximately 2:45 pm employee #1 was killed when the 32 ft. Aluminum extension ladder he was moving co
Employee #1 and Witness #A were insulators for E. J. Bartells. On May 10, 2001 both employees were cleaning up a project th
employee #1 was on a ladder, hanging a piece of steel. A witness heard him moan and employee #1 fell off the ladder. He was
on 10/30/98 at 12:35 pm employee #1 was returning from lunch to begin work at building concrete forms when he had just put o
death most likely due to natural causes
Two workers for Edmonds Gutter Co were in a JG Lift man basket on December 21, 2001 at approximately 10:00AM. the work
Two workers for Edmonds Gutter Co were in a JG Lift man basket on December 21, 2001 at approximately 10:00AM. the work
Employee #1 was driving a 1997 T-800 Kenworth dump truck loaded with approximately 8 yards of soil. The truck was headed
at approximately 7:30 pm on 12/07/99, employee #1 was fatally injured due to crushing injuries suffered in the crash of a truck o
at approximately 7:30 pm on 12/07/99, employee #1 was fatally injured due to crushing injuries suffered in the crash of a truck o
at approximately 7:30 pm on 12/07/99, employee #1 was fatally injured due to crushing injuries suffered in the crash of a truck o
on 5/7/00 at approximately 4:00 PM employee #2 was working in an excavation checking grade for the installation of a 10 inch
on 5/7/00 at approximately 4:00 PM employee #2 was working in an excavation checking grade for the installation of a 10 inch
on 02-16-00 at approximately 3:00 pm one employer of Wilder Construction co was injured by another vehicle which failed to st
on 03/20/98 10:50am employee #1, was sitting on the passenger side of the pick-up truck looking for parts for the work project.
on 4/2/98 3:15pm, (1) observed laying on the south slope of the roofing project. Co-workers tried to revive (1). 911 was called a
employee #1 was painting the underside of the fifth floor landing of a fire escape. He was standing on the fourth floor landing an
employee #1 and a coworker were on a two-point suspension scaffold at a height of approximately 20 ft, pointing the mortar on


                                                     Page 71
                                                         all


a 48 year old, white male was struck with the hammerl from the pile driver. The operator of the crane (manitowac 2900) position
on friday, july 18, 1997, at approximately 8:00 pm, employees #1,2,3 and 4 went onto outrigger supported suspension scaffoldin
on friday, july 18, 1997, at approximately 8:00 pm, employees #1,2,3 and 4 went onto outrigger supported suspension scaffoldin
on friday, july 18, 1997, at approximately 8:00 pm, employees #1,2,3 and 4 went onto outrigger supported suspension scaffoldin
on friday, july 18, 1997, at approximately 8:00 pm, employees #1,2,3 and 4 went onto outrigger supported suspension scaffoldin
on 11/10/97 employee #1 was on a 10 feet, wooden, a-frame ladder using a double insulated bosch demolition hammer to mak
employee #1 was working as the crane operators assistant. The crane operator and the erectors had just finished erecting eigh
multi-employee exposure when servicing of cooling fan without proper lockout caused death of one employee. Other employee
steel worker fell 40' to ground level as he untied his lanyard to move over a crosss beam.
employee working on 2nd level of a single family home under construction fell 20 feet thru a previous cut floor hole for a fireplac
On July 23, 2000 at approx. 12:30p.m. employee, roofer laying asphalt shingle on a 12' by 12' steep roof was not wearing a bod
Employee fell 32' to ground level as he backed into & fell thru an existing skylight when applying a roof sealer on a flat roof.
Employee descending an extension ladder fell to his death, 13 ft. above a concrete floor level, as the ladder slipped below him.
employee #1, a flag person on a highway project, inadvertently stepped into oncoming traffic and was struck by a car and killed
employee #1 bent over in the work zone travel lane and was struck by a dump truck. He died.
a power line worker for an electrical contractor contacted the primary side of a high-voltage transformer at a university. He was
a power line worker was working from an aerial lift. He elevated the bucket of the aerial lift to an overhead power line. He was e
an electrician was installing switchgear in a 480-volt, three-phase electrical cabinet. A phase-to-phase electrical fault occurred,
employees #1 and #2 were hoisting a precast concrete stairway, using the upper stairway as a lifting position. The upper stairw
employees #1 and #2 were hoisting a precast concrete stairway, using the upper stairway as a lifting position. The upper stairw
at approximately 1:15 p.m. on july 19, 1995, employees #1 and #2 were removing a damaged aluminum doorsill in the granulat
employee #1 was loading a bulldozer onto a lowboy type trailer when the bulldozer fell off the side of the trailer, overturned, and
employee #1 was tied off in the basket of an aerial lift that was elevated over water. The lift tipped over and submerged employ
employee #1, of quality painters and decorators, inc., was using a spray gun to paint the steel supports in an impound area. He
employee #1 climbed an electric utility pole to remove old hardware to ready the pole for removal. The pole snapped 14 in. belo
an electrician was moving a wall switch for a 277-volt lighting system while the circuit was energized. The employee shorted the
employee #1 was operating a front end loader/backhoe while employee #2 was riding/standing on the left side step-up. The loa
employee #1 was operating a front end loader/backhoe while employee #2 was riding/standing on the left side step-up. The loa
employee #1 was crushed by a large concrete section of a roof slab while he was engaged in the demolition of a fallout shelter.
employee #1 was working on a new curb project. After pouring concrete for the curb, employee #1 stepped back into the middle
a sheet metal worker was removing a metal-clad cable connector from the end of an energized cable. He contacted one of the
employee #1 was in a 10 ft deep trench when a wall caved in, killing him. The trench wall was not properly sloped or shored.
at approximately 11:35 a.m. on july 8, 1994, employee #1, a laborer, was standing at a freshly backfilled trench after installing a
employee #1 was laying drainage pipe inside an open trench 9 ft deep by 4 ft wide by 45 ft long, which was not sloped or suppo
employee #1 was standing on a tractor battery box in violation of company rules. The tractor's driver told employee #1 not to rid
employee #1 was installing the first core of asphalt shingles to a two-story hip roof. He slipped and fell 30 ft to the driveway. Em
employee #1 was crushed to death when he walked underneath an unsupported section of a steel tank that was being demolis
employee #1 wore a body belt and lanyard but did not tie off. The lift basket tipped and the employee fell 35 feet. He died.
employee #1, a brick layer, was striking a straight line on ground level when he felt ill and collapsed. He died of a subarachnoid
employee #1 was working on a platform 60 ft above the ground. He fell and was killed.
employee #1 was working from a 32 ft aluminum extension ladder at approximately 19 ft above the ground, securing exterior w
employee #1 was walking alongside a pipe that was suspended from a front end loader bucket for transport. The operator lost s
at approximately 10:00 a.m. on august 1, 1994, employee #1 was performing duties as a roofer on a two-story home. As he app
on march 26, 1996, employee #1 and a coworker were installing a new dock plate at twin county grocers in edison, nj. They had
employee #1 and a coworker were unloading material from a truck at ground level. A reshore, a 4 inch by 4 inch by 10 foot long
employee #1 was installing metal flashing on a tower when he collapsed and died of a heart attack.
at approximately 9:30 a.m. on october 30, 1992, employees #1 and #2 were preparing to scrape paint from an overhead canop
at approximately 9:30 a.m. on october 30, 1992, employees #1 and #2 were preparing to scrape paint from an overhead canop
employee #1, an electrician, was turning off the engine of a bucket truck when the engine was exposed to flammable vapors fro
employee #1 was helping three coworkers install a 20 ft by 3 1/2 ft sheet-metal roof panel on a 20 ft roof elevation. He slipped i
at approximately 4:15 p.m. on september 10, 1992, employee #1, the president and owner of a small construction company, wa
employee #1, an electrician, was walking through a mill yard toward the parking lot after working in the tool crib. Employee #1 c


                                                      Page 72
                                                        all


an american 60-ton crane (model no. 7250) was moving a load of lumber. Two employees were standing on the ground, holdin
an american 60-ton crane (model no. 7250) was moving a load of lumber. Two employees were standing on the ground, holdin
employee #1, a crane operator, was unloading a bundle of boiler tubes from a flatbed truck. The crane was overloaded, causin
employee #1 was standing on a scissor lift, 14 ft from the ground, spraying fireproofing material onto the underside of roof deck
employee #1 was climbing a caged ladder. He suffered a heart attack, fell to the ground, and died.
employee was working at the second floor level of a single family home under construction. The employee fell into an unguarde
employee was drilling holes through a gypsum wall. A nozzle was to be inserted into the holes and insulation was to be blown in
employees #1 and #2 were bent over finishing the surface of a frshly poured concrete pad 8'x8'x4" thick. The pad was being po
employees #1 and #2 were bent over finishing the surface of a frshly poured concrete pad 8'x8'x4" thick. The pad was being po
victim was owner of company. Pulling electrical wire at job site and collapsed. Cause determined to be heart attack. No electric
two employees were going off break. They went to job shack to get some plans. The assistant job supervisor went into shack. W
employee was working as a red buster when a crane contacted overhead powerlines at the sewage treatment plat in bingen, w
employee #1, a flagger, was flagging traffic in a construction zone when a westbound vehicle struck and killed him.
at approximately 10:00 a.m. on august 25, 1993, employee #1 was driving an empty lowboy up a logging road to load and haul
at 7:44 a.m. on november 22, 1996, employee #1 was removing a 2-by-4 wood crib that held 5 ft 7 in. by 10 ft sheets of granite
at approximately 10:10 a.m. on january 12, 1992, employee #1 was attempting to fell an 85 1/2 ft long by 11 1/2 in. diameter ald
employee #1 died when she was struck by a motor vehicle while working behind a highway cone barrier.
on 10/16/97 at 7:30 am #1 arrived at the job site drove that trackhoe backwards off the survey lines, told the survey crew he wa
on 02-25-98 at 8:30 am, employee #1 was attempting to remove a shipping pallet from underneath a load on the forks of a fork
employee #1 was crossing behind a dump truck that was backing up and was run over. Employee #1 was carrying boxes on his
at 2:15 p.m. on july 12, 1995, employee #1 was driving his 1976 ford f-150 pickup truck south on state route 167 when, accordi
on 8/4/98 at 2:15pm, employee #1 spreading crushed rock in a 7 foot deep trench, 53 inches wide. The near vertical east wall f
while attempting to start a fire in a stump pile, employee #1 was killed when a falling stump rolled over him.
employee #1, age 17, was operating a compaction roller too close to the side of a road bank when the roller tipped over on its s
on 9-18-96 at approx 2:45 pm employee #1 was extending the boom of the cement pumper truck in preparation for the pour. as
employee # 1 was pruning brush from behind a business. After working approximately 15 minutes, he suffered a heart attack a
employee #1 was moving a 1954 g.i. 6-wheel truck with an attached cable well drilling rig. Traveling north on s.r. 202 to the nex
at approximately 8:55 a.m. on may 28, 1991, employee #1 was assisting in the installation of soundwall panels at a commercia
employee #1 was checking the grade of a cut made by a earth scraper. To get a full load the operator of the scraper, not seeing
at approximately 9:45 a.m. on january 31, 1992, employee #1 was welding two steel ladders together on a 60,000 gallon water
at approximately 12:00 noon, employees #1 and #2, highway construction inspectors for the arizona department of transportatio
at approximately 12:00 noon, employees #1 and #2, highway construction inspectors for the arizona department of transportatio
employee #1 was struck by a bundle of falling trusses. He suffered massive head injuries and was transported to a medical fac
at 9:15 a.m. on october 17, 1995, a truck driver was backing a semi-tractor down a hill toward the back end of a service truck. E
employee #1 was installing fluorescent light fixtures on the fourth floor of an office complex that was being remodeling. He fell f
employee #1 was at the bottom of a 13 ft deep excavation, feeding a 12 in. water main into a horizontal casing going under pim
at approximately 7:51 a.m. on january 16, 1995, employee #1 was working on an electrical power transmission pole. Although e
on april 1, 1994, employee #1 went on top of the roof of a mattress manufacturer that was closed for good friday to perform ser
a swimming pool plastering company employee fell approximately seven (7) feet, head first, into an empty swimming pool while
employees #1 through #7, of three different contractors, were doing remodeling work in a press bay at trw. An employee was g
employees #1 through #7, of three different contractors, were doing remodeling work in a press bay at trw. An employee was g
an apprentice electrician was installing fluorescent lighting fixtures in the ceiling of a second-story stock room. He was working
employee #1 grabbed a horizontal bar that was attached to metal forks weighing 1,150 pounds. Employee #1 lifted himself up a
two painters were removing a 40-foot aluminum extension ladder from a building. The ladder contacted a 7200-volt overhead p
two painters were removing a 40-foot aluminum extension ladder from a building. The ladder contacted a 7200-volt overhead p
on november 4, 1993, at approximately 12:45 p.m., employees #1 and #2 were operating rollers to compact chip seal on the str
on november 4, 1993, at approximately 12:45 p.m., employees #1 and #2 were operating rollers to compact chip seal on the str
employee #1, a hot mop tub tender, fell from a 10 ft 10 in. high flat roof onto an exposed piece of rebar that was 5/8 in. in diame
a 33-year-old maintenance worker for a discount store was instructed to install connections for two lighting fixtures located in th
employee #1 was moving celotex (sub-roofing material) to protect a finished roof from damage from the sharp edges of metal d
employee #1, an iron worker, was assisting in the landing of a load of rebar that was being lowered by a hydraulic crane, using
employee #1 was attempting to board a passenger elevator when her clothing caught on the elevator car door main drive. She


                                                     Page 73
                                                         all


employee #1 walked down a flight of stairs at the 559 elevation, which was approximately 100 ft above grade. When employee
three employees were helping a crane operator move a spreader bar into position so that a crane could lift a modular home to p
three employees were helping a crane operator move a spreader bar into position so that a crane could lift a modular home to p
three employees were helping a crane operator move a spreader bar into position so that a crane could lift a modular home to p
employee #1 was working from a flat roof, preparing to help move a material-laden hand cart. He was at the rear of the cart wit
at approximately 3:30 p.m. on march 7, 1995, employee #1 was laying the fifth row of felt paper on a 109 ft long roof. While wa
employee #1 used a hoistway key to open the elevator door at the first floor, while the elevator car was on the sixth floor. She fe
employee #1 was walking in a road bed when he was struck and run over by a tandem dump truck. He was killed.
employee #1, of the north carolina department of transportation, was acting as a flagman on a highway repair job in rutherford c
an apprentice electrician was checking an energized toggle switch for proper connection. The 17-year-old employee contacted
employee #1 worked as a laborer for a grading company. To prepare a site for a flood control dam, a small number of various k
at approximately 1:00 p.m. on may 11, 1994, employee #1 was working at the yadkin road express stop in fayetteville, nc, an ex
an employee was installing heating ducts in a crawl space in a house. When he drilled a hole in a floor joist, the drill contacted a
an employee was installing heating ducts in a crawl space in a house. When he drilled a hole in a floor joist, the drill contacted a
three employees were moving a 7.90-meter-tall rustgo model 195 mobile work platform across a construction site. They were p
three employees were moving a 7.90-meter-tall rustgo model 195 mobile work platform across a construction site. They were p
three employees were moving a 7.90-meter-tall rustgo model 195 mobile work platform across a construction site. They were p
on october 12, 1995, employee #1 was attempting to cross an intersection when he was struck by an automobile and knocked
employee #1, a truck driver/lowboy operator, was assigned to load a roller compactor onto a lowboy trailer and transport the eq
employee #1 was "framing in" a roof. He had just completed nailing a plywood sheet in place and was moving along a roof joist
highway 264e was being expanded to four lanes. Employee #1 was the supervisor of the job and had instructed the driver of a
two employees were replacing the roof on a furniture company warehouse. The roof was 6.7 meters above the ground. The em
two employees were replacing the roof on a furniture company warehouse. The roof was 6.7 meters above the ground. The em
at approximately 1:15 p.m. on june 17, 1993, employee #1, working on a paving crew, walked from the rear of a dump truck tha
on his first day on a job, employee #1 was operating a farm tractor that had a root rake to clear underbrush, debris, etc. cowork
at approximately 11:40 a.m. on november 10, 1995, employee #1 dismounted his rubber tire backhoe to direct a dump truck to
at approximately 10:45 a.m. on monday, june 21, 1993, employee #1, a 38-year-old cement finisher, and a coworker were work
employee #1 was assisting a pipefitter who was installing a sprinkler system inside a storage warehouse. The rack system insid
employee #1 was instructed to help three employees of another contractor load roofing materials onto a roof. The employees a
employees #1 and #2 were working on a roof truss system 23 ft 2 in. above a concrete floor. The truss system collapsed (domi
employees #1 and #2 were working on a roof truss system 23 ft 2 in. above a concrete floor. The truss system collapsed (domi
employee #1 fell approximately 28 1/2 ft while attempting to step from a tubular-welded frame scaffold onto the eave of a roof 2
employee #1 was driving an mf235 tractor configured with a front brush. Employee #1 was sweeping a road segment that was
employees #1 and #2 and their foreman were ascending the side of a 5-story office building on a werner model #2624, 500 lb c
employees #1 and #2 and their foreman were ascending the side of a 5-story office building on a werner model #2624, 500 lb c
at approximately 3:40 p.m. on september 30, 1992, employee #1 was at the construction site of the roanoke valley cogeneratio
employee #1 was moving equipment into position to build an invert. He was using a backhoe to bring mortar that was in a buck
employee #1 was welding on 19 1/2 in. steel members when he accidentally fell. Employee #1, who was not wearing ppe, was
a roofer was using a milwaukee electric drill. The drill was plugged into two 100-foot extension cord sets, both of which had the
employee #1 was backing up an r80 forklift when one of the rear tires went into a 3 ft deep excavation. The forklift tipped over i
employee #1, age 20, was working on the flat roof of an old grocery store. His employer was removing the original rolled shingle
employee #1 was installing steel decking on a roof that was approximately 45 ft above ground. He had puddle welded the north
employee #1 was struck by a falling truss and knocked off a 10 ft high scaffold. He landed on his head and suffered massive he
a 30 ton hydraulic crane struck and snapped a 7200 volt overhead power line resulting in the electro ution of an employee who
at approximately 8:45 a.m. on march 10, 1997, employee #1, a carpenter with kiewit western company, was working on a new
employee #1 fell 15 ft from a roof access portable ladder onto a wooden pallet and the asphalt surface of a parking lot. He was
two employees, were operating a soil compactor, along side an trench/excavation, that was 10" wide and approximately 24" de
employee #1 was installing a sprinkler system in the auditorium of a movie theater under construction. He was using a self-prop
an employee of an air conditioning firm was sent to a site to install a compressor on a goettl heat pump (model no. Gap2-1, ser
employee #1 was using a front end loader to prepare a grizzly, a large screen used to separate rocks and dirt, that was to be lo
a helper was working with a journeyman power line worker at an electric switching cabinet. The employees were to replace four
at approximately 2:36 p.m. on february 20, 1990, employee #1, age 16, was at the city of tucson's los reales landfill dumping tra


                                                      Page 74
                                                         all


on august 27, 1990, employee #1 was working on a case 1450 track loader. He placed himself between the lower hydraulic arm
employee #1 was near the unguarded edge of a roof doing repairs, 12 ft above a concrete floor. He walked within 1 ft of the roo
at 12:15 p.m. on december 12, 1990, employee #1 was moving dirt with a bulldozer to cover an underground home. He was op
at 10:30 a.m. on january 24, 1992, employee #1 was doing framing work on a one story single family house for kenneth r. yarbr
employees #1 and #2 were placing a bulkhead in preparation for a concrete pour. They were working close to a 16 ft vertical ea
employees #1 and #2 were placing a bulkhead in preparation for a concrete pour. They were working close to a 16 ft vertical ea
at approximately 9:50 p.m. on february 28, 1993, employee #1 was operating a 1977 white 12 yard, 10 wheel dump truck. He w
on the morning of may 10, 1994, employees #1 through #6 were working on various sections of rebar structure walls that were
on the morning of may 10, 1994, employees #1 through #6 were working on various sections of rebar structure walls that were
on the morning of may 10, 1994, employees #1 through #6 were working on various sections of rebar structure walls that were
on the morning of may 10, 1994, employees #1 through #6 were working on various sections of rebar structure walls that were
on the morning of may 10, 1994, employees #1 through #6 were working on various sections of rebar structure walls that were
on the morning of may 10, 1994, employees #1 through #6 were working on various sections of rebar structure walls that were
on the morning of june 21, 1994, employee #1 was working as a grade checker and was guiding a blade operator who was leve
employee #1 was working as the panel operator for a steel remediation unit. During the course of work, employee #1, without a
a heating, air conditioning, and refrigeration mechanic was reconnecting circuits that he had rerouted to make room for a ventila
at approximately 2:10 p.m. on august 4, 1994, employee #1 was supervising belly dump truck drivers hauling soil cement to bu
on 8-3-90 employee leslie leon minich was strippiong a wire in a 6"x6"x3" junction box containing 277 volts, he came in contact
at approximately 3:24 p.m. on december 10, 1990, employees #1 and #2, of national wood erectors, inc., were at the round val
at approximately 3:24 p.m. on december 10, 1990, employees #1 and #2, of national wood erectors, inc., were at the round val
at approximately 3:20 p.m. on april 16, 1991, employee #1, of mcneil construction company, became caught between the conve
employee #1 was sandblasting the metal roof of an old building. To descend, he was using a wooden job-made ladder that was
employee #1 was repairing the brake on the right rear axle of a caterpillar 621b water pull. He was welding in the wheel cup bet
at approximately 4:00 p.m. on january 16, 1992, employee #1 and two coworkers were in a 6 to 7 ft deep trench when an appro
at approximately 4:00 p.m. on january 16, 1992, employee #1 and two coworkers were in a 6 to 7 ft deep trench when an appro
at approximately 7:45 a.m. on october 27, 1992, employee #1 was preparing to fiberglass the interior surface of a swimming po
at 7:30 a.m. on january 16, 1995, employee #1, an electrician for lafferty electric, inc., was working inside a building under cons
on november 18, 1993, at 3:40 p.m., employee #1 was working on the first floor of dillard's restaurant in phoenix, az, when a se
employee #1 was working on a flat roof at the storage area preparing to move materials. While doing so he slipped and fell from
employee #1 jump-started a forklift truck. He was positioned on the ground between the right front and rear tires. He had unhoo
at 2:00 p.m. on july 14, 1992, employee #1, a concrete finisher, was underneath a 20 ft long section of a lattice boom that was 6
an apprentice electrician was installing one double and two single lighting fixtures above a cage washing machine. The employ
at approximately 7:20 a.m. on august 21, 1995, employee #1, who had been a roller operator for three months, was driving a hu
on july 9, 1993, employee #1 was working at a construction site installing forms for poured concrete basements. He worked for
on february 3, 1994, employee #1, a partner in rasche brothers contractors, and employee #2 were working on a carpenters' br
on february 3, 1994, employee #1, a partner in rasche brothers contractors, and employee #2 were working on a carpenters' br
employee #1 was helping his son while also learning how the operation worked. They were using a fiberglass ladder with hooks
employee #1, the president of his company, was installing metal studs for future offices. He was standing on a baker's scaffold
a backhoe had been used to remove the dirt from around the base/foundation of a 26 ft 3 in. long semicircular stone wall. That
employee #1 was the vice-president of a company that was installing downspouts and gutters on new townhouses. That mornin
a foster medical supplies delivery truck was backing out of the bon secours hospital driveway. Employee #1, of landis & gyr, wa
and victim received fatal electrical shock. Mr ingle (victim) had only been working for co 2 1/2wks as laborer he was showed on
employee #1 and coworkers were moving a hi-lo two-point suspension scaffold, model d800, around the corner of a building. E
employee #1, age 19, and a coworker were assigned to take down two dead trees. Employee #1 was standing approximately 4
employee #1 was removing a 4 in. diameter by 20 ft long steel track that was suspended from a roof by angle irons attached ab
on april 26, 1991, employee #1, a truck driver for case construction group, inc., beltsville, md, was driving a blue 1979 internatio
employee #1 and coworkers were laying pipe in a 60 ft long trench that was 2 ft wide at the bottom and 6 ft wide at the top, and
at approximately 1:15 p.m. on june 20, 1991, employee #1 and a coworker were working from a skeletal steel structure at a hei
employee #1 and coworkers were preparing to use a 40t lorain lrt 400 crane, serial #37197. to remove propane tanks weighing
at about 1:00 p.m. on august 22, 1991, employees #1 and #2 got on a two point suspension scaffold that was positioned on the
at about 1:00 p.m. on august 22, 1991, employees #1 and #2 got on a two point suspension scaffold that was positioned on the
at about 9:30 a.m. on july 15, 1991, employee #1 was positioned on a 47-inch square wood pallet that was elevated by the fork


                                                      Page 75
                                                         all


at approximately 4:30 p.m. on march 9, 1990, employee #1, a plumber with b & g, inc., finished his day's work at a construction
employee #1 and several coworkers were assigned to paint the understructure of the route 40 bridge in the area of pier #16. Th
employee #1 was assisting in preparing the rock grapple for hoisting when the grapple rolled and shifted, striking the employee
employees #1 and #2 were working on a sewer line construction project near littleton, nc, in halifax county. Both employees we
employees #1 and #2 were working on a sewer line construction project near littleton, nc, in halifax county. Both employees we
an electrical fault occurred in a switchboard, and the ensuing electric arc burned a power line worker. He died as a result of his
two employees were moving a metal ladder. The ladder contacted an overhead power line. One of the employees was electroc
two employees were moving a metal ladder. The ladder contacted an overhead power line. One of the employees was electroc
at approximately 1:20 p.m. on april 29, 1993, employees #1 and #2 were working from a two-point suspension scaffold, welding
at approximately 1:20 p.m. on april 29, 1993, employees #1 and #2 were working from a two-point suspension scaffold, welding
employee #1 was working on a roof that was 45 feet 6 inches high, breaking deck sheeting loose from a stack. The decking lay
an electrical contractor had been hired to install a 400-ampere electrical service to a mill building. On june 29, 1995, the contrac
employee #1 was riding an ingersoll sp-42 on a slope when the equipment overturned on him. He was crushed and killed.
on january 12, 1999 aproximattely at 9:00 am while the operator of and excavator (digger) made an excavation of aproximately
at approximately 7:30am on june 2, 1999, the employee was working inside of excavation 12'- 0" deep, preparin a form work fo
the employer was working inside of excavation approximately 7' - 0" to 8' - 0" deep, 5' - 0" wide and 9' - 0"to 10' - 0" long cleanin
employee #1 was working from a manually propelled scaffold when he fell at 10 ft 6 in. to the floor and was killed. The scaffold
employee #1 and three coworkers were installing optic fiber cable systems. Employee #1 was inside the trench giving directions
can not read
can not read
employee died by a heart attack when was ready to start his duties as welder.
the employees was fatally injuried when a cement pile that was been cut falled over him. His occupation was carpenter since tw
employee did have a metal pipe in his hands when accidentally made contact with an electric line of 4,160 volts located beside
one employees died due a multiple contusions at the abdominal area and other employee resulted with injuries at the some are
one employee was killed and other resulted injuried when a cylindrical steel frame collapsed and falled over them. They were in
one employee was killed and other resulted injuried when a cylindrical steel frame collapsed and falled over them. They were in
employee #1 was walking at the edge of an 8 ft in diameter by 4 ft deep excavation. He fell into the excavation and onto a 5/8 in
employee #1 and a coworker were using a crane to place a flying form (underfloor) over the seventh floor of a building. Employ
an employee working in demolition activities a wall 89" inch long high and 4" wide fall over hip on legs.
the employee were peaning a path way on november 4, 1998 and three feldown and hit the head of elvin patricio albarran dying
working in a job platform, tying rods the job platform, 19 " wide x 12 feet large and 7'3 " hight. The employee was kicking the mo
after day labor (painting) one employee put out hisfull harnees, and moved to an open side floor to close the space and fall dow
he died of asphycia . on july 1, 1999. Was inside and excavation 5 feet depth.
mientras empleado manejaba plancha de ziw en el techo del edificio donde iba a ser instalada, este cayo al vacio por un hueco
mientras empleados realizaban operacion de instalacion de acero vertical (varillas de 11/8 diametro), estas se colapsaron resu
employees were working in electrical installation. Employee #1 placed two panels over the beams as a platform to stand on. Th
employee #1 fell 18 ft from the roof of a residence and was killed. The residence was not a job site.
employee #1 was inside a 6 ft 8 in. deep by 6 ft wide by 40 ft long excavation when one of the walls collapsed. His partners pull
employee #1 and two coworkers were on a 4 ft by 24 ft platform on the sixth floor of a building. They were aligning a 24 ft long w
empleado rompiendo pared de concreto con marron empleado viene en contacto con cables de 120 vlts. Empleado muere ele
employee #1 was standing on a steel beam when his foot slipped. He fell to the ground and was struck and killed by the falling
on 09/21/99 at approximately 1:00 pm employee #1 was spray painting a residence while on a 12 foot portable ladder. The port
on june 25, 1994, employee #1, an equipment operator, was alone at a worksite in metairie, la. He was working with a john dee
employee #1, an electrician, was standing by an electrical box approximately 24 feet away from an 8-inch masonry block wall th
deceased was working with 2 other workers installing alum;inum snap on window frames on front of church bldg on 7/28/94 at a
at approximately 10:00 p.m. on august 30, 1994, employee #1 was working as a spotter at a levee construction site north of lak
part of a house leveling crew was under a house seeking to level its central portion. The company owner was inside the house,
part of a house leveling crew was under a house seeking to level its central portion. The company owner was inside the house,
deceased employee was working with other workers on 5/21/98 pulling flexible conduit through a bore hole to be installed in a s
at approximately 2:00 p.m. on july 20, 1993, employee #1 was working on a roof, installing a waterproof tarp, when he backed i
employee #1, a carpenter, was stringing interior partition walls in a residential home under construction. ("stringing" means to s
employee #1 was removing brush from the side of a ditch containing one ft of water when he fell. Workers from another compa


                                                      Page 76
                                                          all


at 1 p.m. on february 6, 1995, employee #1, a carpenter, and a coworker were moving a 20 ft long by 12 in. wide metal scaffold
employee #1 and a coworker were carrying 20 ft long needle beams on a plywood subfloor just beneath the roof over an operat
employee #1, a sheetmetal helper performing mechanic work on a dodge pickup truck, had the back end of the truck raised wit
employee #1, an iron worker, was working with a crew installing metal decking on the roof of a building 38 ft from the ground. E
employee #1, a laborer, was clearing debris from a flat roof 14 ft above ground in preparation to repair the roof. There was no p
a power line crew was moving a 7600-volt, three-phase overhead power line from an old pole to a new one. One of the power li
on october 16, 1995, a delivery truck of steel needed to be unloaded. Employee #1, a superintendent, was operating the mantis
at approximately 9:30 a.m. on december 1, 1995, four employees were leveling the bottom of a sewer ditch that was approxima
at approximately 9:30 a.m. on december 1, 1995, four employees were leveling the bottom of a sewer ditch that was approxima
employee #1 was installing insulation panels on a large flat roof. The employer was using a warning line that was 17 feet from t
at approximately 11:00 a.m. on march 1, 1996, employee #1, an 18-year-old, and a coworker were lowering and leveling a 16 ft
at approximately 6:50 a.m. on april 18, 1996, employee #1 was working with a crew removing planking from the roof of a wareh
at 12:33 a.m., employee #1 was moving lights on the roof of a 40 ft tall storage tank when he tripped and fell through a roof ope
at approximately 8:00 a.m. on may 9, 1996, employee #1, of h and s construction, was taking an asphalt core sample from stat
electrocution
on june 14, 1996, employee #1, a maintenance mechanic with mcmanus construction, inc., for about three years, was working
employee #1 was removing cables from the top of the #1 port tank. He was walking on the beam of a bay divider inside the tan
employee #1, a cablevision cable splicer, was using a 28 ft fiberglass ladder to work on some coaxial cables. A construction cre
employee #1 and two coworkers wanted to tighten bolts attaching a gear box to a mowing machine. They drove the tractor up t
employee #1 was operating a broce t-15 power broom to sweep debris from a road sub-base prior to the installation of asphalt.
employee #1, the only employee at the site, was receiving a large air compressor from a rental service company. The driver of
at about 10:30 a.m. on december 13, 1993, employee #1 was at a site directing truck drivers who were backing in to deposit the
at 11:45 a.m. on november 5, 1993, employee #1 was one of two connectors receiving steel trusses. A truss was in place and w
on november 19, 1993, at approximately 11:00 a.m., employee #1 was moving in a pipe rack at the exxon docks, cleaning the p
at 3:00 p.m. on february 3, 1994, employee #1 cut the metal leg of a water tower with a torch. The leg was supposed to fall awa
at approximately 11:00 a.m. on february 24, 1994, employee #1 was working with a foreman of the company on the roof of a bu
employee #1 was on a truck-mounted rotating and articulating personnel platform painting an oil field horsehead pump in a rem
employee #1, a crane operator, and a coworker were adding a 15 ft section of latticework boom to an 18 ton truck crane. Cotte
at approximately 12:25 p.m. on april 29, 1994, employee #1 was working on top of a 5,000 barrel fuel oil stock tank at delta 83,
at about 11:00 a.m. on may 25, 1994, employee #1 was working with a decking crew at a walmart service center store under co
an 80,000 lb payhauler construction truck was pulling out of a parking lineup to drive to the hauling lanes. Employees #1 and #2
an 80,000 lb payhauler construction truck was pulling out of a parking lineup to drive to the hauling lanes. Employees #1 and #2
deceased ee was working with a crew at a new water tank work site in chauvin, la. The company had been contracted to paint
on october 30, 1997, at approximately 2:10 p.m., employees #1 and #2 were setting a sewer tank into position using a crane m
on october 30, 1997, at approximately 2:10 p.m., employees #1 and #2 were setting a sewer tank into position using a crane m
four employees were replacing a joint-use utility pole supporting electric power, telephone, and cable television lines. The existi
employee #1 was erecting scaffold lighting towers, working approximately 70 feet above the ground while placing support brace
some employees were using an 18-ton grove crane to unload 20-foot-long pipes from trucks. An assistant superintendent was
employee #1 was instructed to leave his roofing work and return to ground level to get more metal roofing batten strips. While le
employee #1 was setting grating approximately 48 ft above ground. A piece of grating measuring 3 ft by 10 ft had slipped off the
an employee was spray painting the exterior of a building from a 32-foot-long aluminum extension ladder. A building tenant hea
employee #1 was killed when a water pumping station being torn down prematurely collapsed. Employee #1 was pinned undern
at approximately 11:00 a.m. on may 29, 1994, employee #1 was digging a 4 ft trench with a caterpillar bulldozer. As he was ma
an electrician was standing on a 6-foot step ladder, installing a lighting fixture. He had not deenergized the circuit before installi
employee #1, a supervisor for general supply deck & floor underlayment inc., misjudged the movement of a material hoist when
a contractor was building a support foundation for a highway sign. The contractor drilled two shafts that measured 3 feet wide b
employee #1 and a coworker were securing a welder to a boat when a big wave sank the boat. Employee #1 drowned.
employee #1 was standing on a six-foot fiberglass stepladder holding a power saw. He was trying to cut a corner to fit on top of
at approximately 5:00 p.m. on march 11, 1995, employee #1 was helping another employee put plastic over roofing materials th
at approximately 10:30 a.m. on march 17, 1995, employee #1 was on top of an i-beam spreading and connecting bar joists. A b
on april 26,1995, employee #1 was assisting two other employees and a hoist operator in erecting a radio tower. He was riding
employee #1 was driving a scissor lift that was extended to 22 feet. A wheel fell into a 2 foot by 2 foot hole and the scissor lift ov


                                                      Page 77
                                                         all


employee #1 was on a mobile scaffold removing a strap from an air conditioning duct when the duct fell and hit the scaffold. Em
employee #1 was trimming a wood truss with a circular saw when he fell 19 1/2 feet to the pavement. He died at the hospital fro
employee #1 was driving a 2 1/2 ton maintenance truck with a flat bed up a slight hill. When the truck stopped and started to ro
an employee was working on top of a heating, ventilation, and air conditioning plenum. A hanger bolt that had been holding the
an employee was installing a gas line at a residence. While he was working beneath the house, he apparently contacted an ene
employee #1 and the store manager were carrying a sheet of marble upstairs. Employee #1 was killed when he fell from the un
the crew had just complete a concrete deck pour on the second floor of the building. Clean-up operations were stated when the
lineman working on distribution line, 7200 volts. Victim came in contact with live parts and ground.
employee #1 was carrying a full brick carrier off a scaffold when a scaffold plank fell out from under him. He fell 14 feet onto a c
employee #1 was a laborer hired from a leasing company to help install corrugated metal sheeting for a roofing company the fo
employee #1 and five coworkers were stripping an asbestos tile floor when a flash fire broke out. Employee #1 was killed and th
on august 7, 1996 at approximately 9:30 a.m. employee #1 and deco contractors were laying out the area underneath the hous
an employee had been given the task of painting a metal utility pole with a spray gun. He was using a cherry picker and had pa
on september 22, 1996, a mobile home set-up crew was nearing completion of a double-wide set up. Employee #1 was under t
employee #1, a truck driver, had just delivered a load of dirt to fill a trench. The site was small and congested, but the driver dec
employees #1 and #2 were engaged in road construction when they were struck by a motor vehicle. They were both killed.
employees #1 and #2 were engaged in road construction when they were struck by a motor vehicle. They were both killed.
employee working construction job died of heat stroke.
between 7:30 and 8:00 a.m. on march 29, 1994, employees #1 and #2, the lift operator, were standing on the platform of a self
between 7:30 and 8:00 a.m. on march 29, 1994, employees #1 and #2, the lift operator, were standing on the platform of a self
employee #1 was twisting seams of chicken wire on a roof of a building addition. He was working from a mobile scaffold when t
employee #1 was inside a trash dumpster rearranging trash as it was dumped into the container. The dumpster was nearly full
on november 22, 1995, employee #1, along with two coworkers, was attempting to break out a stuck joint in the bore stem of a
employee #1 was unbolting a vertical beam without using any type of bracing to hold the beam in place. After one of the bolts w
employee #1 was inside a box receiving scaffolding members from the third floor when the box fell to the ground. He was killed
employee #1, the company owner, and his crew were framing a two-story house. The roof had been completed along with mos
abstract
employee #1 was hoisting sheetrock to a roof that was 14 ft 6 in. above ground level when he fell and was killed. The employer
a power line worker was working from an aerial lift bucket, stringing the neutral conductor of a deenergized overhead power line
the victim and a co-worker were installing sheet rock by attaching it to metal building studs with and electric powered screw dril
employee #1 was told by his supervisor to pull up a sump pump at the bottom of a trench to read the serial number. The trench
at 12:45 p.m. on august 24, 1996, an electrical contracting crew was laying 4 in. Schedule 40 pvc pipes in a 3 ft 7 in. deep by 6
at approximately 4:00 p.m. on november 22, 1996, paving, excavating, and trucking contractors were working on a project that
employee #1 was realigning a ceiling joist by pulling the joist back into place with a cheap come-along and some fabric straps.
jessie e. seaton was fatally burned on or about oct. 2, 1997, when an electrical circuit recloser failed to open, shorted out and e
employee #1 was elevated about 15 ft on the fork of a high lift truck removing a steel pipe column that was supporting a span o
employees were cleaning residue buildup on the inside of a 605-foot high chimney of a lignite coal power generating plant. The
employees were cleaning residue buildup on the inside of a 605-foot high chimney of a lignite coal power generating plant. The
the lead power line worker on a crew was rotating the boom on a digger-derrick to position it for digging a utility pole hole. A 720
employee #1 was working with a five man crew that was erecting a metal building, preparing to perform welding operations from
employee #1 dismounted a personnel platform while it was on the ground to unhook the main crane line from a pole that had ju
a vertically-movable steel work platform was being constructed as a component of an automated aircraft maintenance stand. A
between 7:30 and 8:00 a.m. on march 29, 1994, employee #1 and employee #2, the lift operator, were standing on the platform
between 7:30 and 8:00 a.m. on march 29, 1994, employee #1 and employee #2, the lift operator, were standing on the platform
between 7:30 a.m. and 8:00 a.m., on march 29, 1994, employee #1 and employee #2, the lift operator, were standing on the pla
between 7:30 a.m. and 8:00 a.m., on march 29, 1994, employee #1 and employee #2, the lift operator, were standing on the pla
employee #1, who was installing shingles on a roof, stepped backward off the roof and fell 12 ft to his death.
employee #1, a bulldozer operator, exited his caterpillar d7g bulldozer and was caught by its right side track, pulled between the
employee #1 was attempting to jump start a tractor by connecting battery cables to two other trucks. He was standing in front o
a self-employed plumber was working under verbal contract to a realty company. He was working under a pier-and-beam hous
employee #1 fell about 60 ft through the decking flooring of a work platform on the top of a tubular welded frame scaffold. The p
employee #1 was backing a stand-up forklift truck with his head extended beyond the vehicle. His head became pinned betwee


                                                      Page 78
                                                           all


employee #1, a 22-year-old laborer, and a signalman for a crane that was lowering an 8 ft by 8 ft precast concrete panel were s
employee #1 was helping dismantle a crane boom to transport the boom and the crane power unit to the company yard. The co
employee #1 was a member of a crew installing corrugated metal roof sheets and securing them with self-tapping screws to the
at 10:26 a.m. on october 11, 1995, employees #1 and #2 were at a height of 30 ft removing two pieces of angle iron from 139 ft
at 10:26 a.m. on october 11, 1995, employees #1 and #2 were at a height of 30 ft removing two pieces of angle iron from 139 ft
an electrician was working from a portable aluminum ladder replacing an overhead lighting fixture. He was about 4.9 meters ab
an 18-year-old general laborer for a sand and gravel firm was cleaning gravel from under and around conveyor systems for a c
employee #1 was attaching a backhoe attachment to a clark bobcat. He accidentally contacted the hydraulic controls to the bac
employee #1 was taking ultrasonic readings while standing on an extension ladder placed inside a large recovery stack (chimne
employee #1, of grimmett enterprises inc., was working alongside a caterpillar scraper. The crew was taking elevation grades a
employee #1 was applying grout in a manhole. There had been a 20 to 36 in. rubber plug installed into a 36 in. sewer line that e
employee #1 died of asphyxia when he was directed to enter a confined space without full compliance with confined space stan
employee #1 drove off the side of a logging road in a dump truck. The truck rolled about two times, crushing and killing him. He
at approximately 9:00 a.m. on december 6, 1994, employee #1 was working off a 25 1/2 in. wide, 15 ft 10 in. long platform witho
employee #1 was installing a skylight when he fell through the opening approximately 12 ft to the concrete floor. He sustained h
a crew was installing fiber optic cable for southwestern bell telephone. Employee #1 was bent over in a trench, laying 4 in. Pvc
employee #1 was on the roof of a building picking up debris and putting it down the chute to a dumpster. The project had begun
The employer was picking up construction debris at a residential construction site and loading it into a 1967 Chevrolet dually tru
employee #1 was installing a catwalk on a fuel tank when a spark from the welding torch set off an explosion in the tank. No pa
at approximately 2:00 p.m. on october 9, 1994, employee #1, a supervisor, told two employees that he needed to weld a 12 in.
employee #1, the owner, was standing on the top of a set of stairs approximately 6 ft from the floor, taping and bedding a wall,
employee #1, working on a 27 ft high flat roof, tripped while shoveling gravel and fell to his death through an unguarded skyligh
employee #1 was lying on the floor working under a small shop-made trailer that was supported by three jack stands. Another e
employee #1 was preparing to go to lunch. He began walking across an incomplete 23 ft high metal roof deck, heading toward
employee #1 was working at the edge of a bridge deck. He had removed his safety belt and lanyard when the section of bridge
after using a forklift to unload some equipment from a truck, employee #1 noticed that his right front tire was flat. He drove 25 to
a crane operator was moving his crane across a berm dividing two unpaved roads. The crane's boom, which was nearly vertica
employee #1 had been picked up that day to help roofers by cleaning up on the ground surrounding the roof. Despite being war
on october 29, 1992, employee #1 was leveling the bottom of an excavation. The excavation was 100 ft long, 6 1/2 to 9 1/2 ft de
employee #1 was trimming grass with a weed wacker along the berm of an entrance ramp from a rest stop onto i-71 southboun
on or about may 28, 1993, employee #1 was working on the roof of the clean water systems company when he fell 40 ft throug
employee #1 was installing concrete blocks on a 3 buck high tubular welded frame scaffold with a work platform 18 1/2 ft high.
employee #1 was on a 37 foot high flat roof taking propane tanks onto the roof from a roofer hoisting jack. He was wearing a bo
the crane, operated by employee #1, was lifting 15,000 pounds of 8 inch by 40 foot polyurethane pipe onto a tractor trailer. The
employee #1 was helping to lift equipment off a roof with a crane. The weight of the equipment was not determined before it wa
employee #1 had just unhooked safety line to got to lunch when he saw a piece of roofing material. Employee #1 walked to edg
on 07/09/98 at 04:48pm employee #1 was using a skid-steer loader doing land preparation for the setting of forms for cement f
on 08-09-95 at 9:10 am, employee #1 was working in the main distribution room. Employee #1 was working on an energized el
after notifying the pilot car operators, the driver stopped the truck to raise the trailer so it wouldn't high center. The front and rea
employee #1, an iron worker foreman, was standing under purlins that were being set in place and installed to stabilize a steel s
at approximately 1:20 p.m. on december 29, 1995, employee #1 and a coworker were laying 4-by-8 sheets of plywood on the ro
rollover
The deceased expired in the ladies room at her work place from heart disease per King County medical examiner. The employ
the victim was removing a gutter strap while standing 12 to 14 feet high on a ladder.the victim was using a hammer and chisel t
at 10:00 a.m. on november 2, 1994, employee #1 was connecting a house sewer line to the main sewer line at the base of a ve
at approximately 2:45 p.m. on november, 11, 1994, employee #1 suffered a spontaneous cerebral aneurism and died.
on a construction site after operating a company vehicle, the employee was found in the reclined drivers seat. This was at 3:07
employee #1 and a coworker were discussing with the foreman what to do with a pile of gravel. They were standing near a pile
on september 29, 1990, employee #1 and a coworker, both at&t systems installer technicians (electricians), were installing wire
employee #1 was preparing to paint overhead structural steel. He hung a 20 in. wide by 20 ft long two-point suspension-type sc
at approximately 7:25 a.m. after employee #1 and a coworker, an iron worker, rigged a bundle of corrugated metal decking, it w
employee #1 complained of chest pain and shortness of breath. Suffering a heart attack, the employee was transported to the h


                                                       Page 79
                                                         all


employee #1 was installing 8 in. diameter by 13 ft long plastic sewer pipe at the bottom of a 10 ft 5 in. deep by 32 ft long excava
at approximately 2:00 p.m. on april 21, 1997, employee #1 was helping a coworker who was adjusting the front elevator door m
on may 24, 1996, employees #1 and #2 were working from an extendible articulating boom platform on an sbc snooper aerial li
on may 24, 1996, employees #1 and #2 were working from an extendible articulating boom platform on an sbc snooper aerial li
two employees were raising a 7.3-meter-long (24-foot-long) steel pipe for a well. As it neared a vertical position, the pipe contac
two employees were raising a 7.3-meter-long (24-foot-long) steel pipe for a well. As it neared a vertical position, the pipe contac
two employees were raising a 7.3-meter-long (24-foot-long) steel pipe for a well. As it neared a vertical position, the pipe contac
two employees were raising a 7.3-meter-long (24-foot-long) steel pipe for a well. As it neared a vertical position, the pipe contac
at approximately 1:00 p.m. on april 17, 1991, employee #1 and his brother were staking out bar joists on the roof of the third flo
at approximately 2:30 p.m. on september 10, 1991, employee #1, an iron worker, was standing on a 1 ft wide, 6 ft 3 in. long, an
two construction laborers ("hod carriers") were working from a 15-foot-high tubular, welded frame scaffold. They were dropping
two construction laborers ("hod carriers") were working from a 15-foot-high tubular, welded frame scaffold. They were dropping
employee #1 and four coworkers were in a mausoleum wrecking concrete forms from crypts. Employee #1 and two coworkers
an electrician working alone was pulling the neutral conductor for a lighting circuit into the main circuit panelboard for a conveni
at approximately 8:55 a.m. on june 3, 1991, employee #1, the anchor installation crew foreman was directing work of the eight m
at approximately 2:40 p.m. on august 31, 1995, employee #1 was installing sewer pipe in a trench when a wall of the trench col
employee #1 was installing 6 in. pvc sewer pipes in a trench 5 1/2 ft deep, 7 1/2 ft wide at the top, 32 in. wide at the bottom, and
after digging an 11 ft long by 4 ft wide by 7 ft deep trench with a tractor-mounted backhoe, employee #1 entered the trench to re
at 2:05 p.m. on july 3, 1991, employee #1 fell from the safety guard that runs under the conveyor to prevent television picture tu
an employee was dumping a load of stone at a temporary levee. The levee was being constructed to stem the flow of flood wat
employee #1 was descending from an 18 ft high roof to get a proving cone needed to finish installing a chimney flu. When he p
a power line worker was relocating a 7200-volt overhead power line, moving it 50 feet to the east. The power line relocation wa
at approximately 3:30 p.m. on or about july 10, 1991, employees #1 and #2 were standing atop an 80,000-gallon capacity tank
at approximately 3:30 p.m. on or about july 10, 1991, employees #1 and #2 were standing atop an 80,000-gallon capacity tank
at approximately 3:30 p.m. on or about july 10, 1991, employees #1 and #2 were standing atop an 80,000-gallon capacity tank
at approximately 3:30 p.m. on or about july 10, 1991, employees #1 and #2 were standing atop an 80,000-gallon capacity tank
at approximately 3:30 p.m. on or about july 10, 1991, employees #1 and #2 were standing atop an 80,000-gallon capacity tank
a power line worker was on a catwalk at the top of a transmission tower, performing maintenance and making repairs. The emp
at approximately 2 pm on february 19, 1992, employee #1 was painting station markers from the berm of u.s. highway 31 north
at approximately 1 pm on october 18,1991, employee #1 was using a gmc truck equipped with a hi-ranger hydraulic lift system
at approximately 8:45 am on august 15, 1991, employee #1 was dismantling a large fan and cleaning the parts with a solvent. H
at approximately 8:30 a.m. on june 10, 1993, employee #1 and a coworker were replacing a 12 ft by 12 ft overhead garage doo
at approximately 8:05 a.m. on june 9, 1993, employee #1 was removing fallen dirt from the northeast corner of an excavation w
employee #1 was carrying a bundle of shingles up a faulty ladder to two coworkers who were working on a pic (ladder jack scaf
at about 5:40 p.m. on september 14, 1993, employee #1 was standing in the bed of a 1986 ford pickup truck picking up traffic c
an employee was painting the metal structure inside a substation. He contacted a 34-kilovolt energized part within the substatio
employee #1, the crew leader, was assisting two other employees in the installation of insulation and metal decking on a flat roo
employee #1 fell 80 ft from a microwave tower during its dismantling. He had a body belt and a safety strap in use for positionin
two millwrights had removed the gate valves from the #2 boiler to the fly ash conveyor and were cleaning debris from the valves
employees were constructing a precast concrete collar beam to support a manhole lid at the surface entrance of a tunnel shaft.
on february 24, 1992, employee #1, who was working on a tubular welded frame scaffold, fell 25 ft to the asphalt. He sustained
at approximately 1:40 p.m. on september 3, 1993, employee #1 was working on a re-roof job. He took a drink of water from the
in june 1992, employees #1 and #2 were using a grove scissor lift, model m31/hart, to string cables beneath the route 195 over
in june 1992, employees #1 and #2 were using a grove scissor lift, model m31/hart, to string cables beneath the route 195 over
this accident occurred 9.5 miles offshore on a jackup rig. Diffusers were being installed for the sewage discharge tunnel of the
this accident occurred 9.5 miles offshore on a jackup rig. Diffusers were being installed for the sewage discharge tunnel of the
this accident occurred 9.5 miles offshore on a jackup rig. Diffusers were being installed for the sewage discharge tunnel of the
employee #1 fell 21 feet through a chimney opening in the second floor to the lower concrete floor. He was killed.
employee #1 was welding. Minutes after he finished lunch, he collapsed on the job site. According to the state medical examine
employee #1 was shoveling earth, which had been drilled by an auger, when an unguarded rotating part located just above the
employees were removing stone from the exterior of a building, while a tower climbing work platform was elevated 80 ft to the 8
employees were removing stone from the exterior of a building, while a tower climbing work platform was elevated 80 ft to the 8


                                                      Page 80
                                                          all


employee #1, who was alone, was apparently clearing a lot for a building site. He was discovered with a tree lying across his ch
employee #1 and coworkers were repaving route 49s. He was working behind a dump truck full of asphalt. The truck backed up
employee #1 fell about 52 ft from a scaffold to a brick courtyard. He died.
employee #1 was working from a makeshift carpenter's bracket scaffold attached to the side of a future sea wall, inside a coffe
employee #1, age 19, was felling trees when he was struck and pinned by a large pine tree. He died of asphyxia.
at approximately 2:20 p.m. on august 20, 1996, employee #1 was helping to remove a structural steel beam that was secured t
at approximately 12:00 noon on november 18, 1996, employee #1 was pointing the chimney of a private residence. He was wo
at approximately 1:15 p.m. on january 18, 1991, employee #1 was attempting to remove a pipe nipple from a pipe that was app
employee #1 stepped/fell onto an unsupported floor opening cover and fell 33 ft to a concrete floor. Employee #1 was hospitaliz
at approximately 2:10 p.m. on september 4, 1992, employee #1 was preparing to step onto an 18 ft wide by 36 ft high scaffold t
employee #1, self employed, was on the roof of a house repairing and cleaning roof tiles. Apparently, he slipped and fell approx
employee #1 was checking the work area, and was either entering or leaving a two-point suspension scaffold when the support
an employee was directing the filling of a hopper attached to an asphalt spreader. The hopper was being filled from a 10-wheel
employee #1 was installing aluminum siding on a building's fascia from an approximately 30 foot high scaffold. The scaffold con
employee #1 was part of a group of construction employees who were removing a built up flat roof containing asbestos.they we
employee #1 was driving a caterpillar model 966c front end loader, serial #76j6638, westbound crossing a bridge that spans int
an employee climbed a 32-foot wooden extension ladder to cut down three conductors from a utility pole. His employer told him
at approximately 1:00 p.m. on september 2, 1992, employee #1 was replacing a 4 ft by 8 ft by 3/4 in. temporary plywood cover
on october 31, 1994, employee #1 was form stripping from below a new bridge deck. He was standing on a temporary walkway
employee #1, a laborer, was removing debris from an old build-up roof and throwing the material into a dumpster. He lost his fo
employee #1, a truck driver, arrived at a job site with his vehicle and was in the holding area with other drivers. He apparently w
employee #1, a truck driver, arrived at a job site and was in the holding area with other drivers. He apparently went into the bac
at approximately 10:30 a.m. on april 7, 1993, employee #1 and a coworker were cutting a skylight opening in a steel roof deck a
at approximately 9:06 a.m. on october 25, 1993, employee #1 was attempting to cut a 10 in. Pvc water line that had a static pre
employee #1 was on the second floor trying to locate a water leak in existing plumbing. He was standing between a hot water h
employee #1 was attempting to push an approximately 90 lb chimney block up a 4:12 pitch roof surface. He lost his footing and
employee #1, a foreman, and two coworkers, a mason and a laborer, were caulking exterior windows of a 5 story brick building
employees #1 and #2 were at the shoulder of the southbound lane of the major deegan expressway, setting out traffic cones to
employees #1 and #2 were at the shoulder of the southbound lane of the major deegan expressway, setting out traffic cones to
employee #1, an iron worker foreman, was dispatched with 3 coworkers to repair a powered industrial truck. To get from the sta
employee #1 was working on a roof which was approximately 32 feet above the ground. The employee removed a roof opening
employee #1 was working on a catenary scaffold approximately 30 ft above a roadway, painting the structural steel of the eleva
at approximately 2:30 p.m. on june 28, 1991, employee #1 was attempting to straighten out a bent rear section of the body of a
an employee was working in close proximity to the primary side or line side of this 13.2 kv nominal volt system. It is believed tha
on november 8, 1994, employee #1 and a coworker, of roman waterproofing and restoration, and employee #2, of antonucci an
at approximately 11:30 a.m. on july 6, 1991, employee #1 was removing debris from pathways on the third floor of a building in
employee #1 was working on a tunnel boring machine. He was climbing from one location to another on the machine when he f
employee #1 was working in a water tunnel shaft when a piece of hoisting equipment that was being used above him toppled in
after climbing over the concrete barriers that divided the lanes and his work area, employee #1 was struck and killed by a truck
the employee was working on the north bound side of the thrugs neck bri- dge. He was in the process of removing the orange c
on may 3, 1995, employee #1, a crane operator, was lowering a manlift 40 ft below a bridge when the crane tipped over the sid
on may 3, 1995, employee #1, a crane operator, was lowering a manlift 40 ft below a bridge when the crane tipped over the sid
at 1:51 p.m. on august 24, 1995, employee #1 and a coworker were clearing debris from a roof, in preparation for the placemen
employee #1 was breaking up a concrete floor with a jackhammer while standing on an aluminum platform. He fell approximate
employee #1 was attempting to load a forklift onto a flatbed trailer. The forklift fell off the trailer and struck employee #1. He atte
at approximately 5:15 a.m. on october 22, 1992, employees #1 and #2 were working in an unprotected trench that was approxim
at approximately 5:15 a.m. on october 22, 1992, employees #1 and #2 were working in an unprotected trench that was approxim
employee #1 was a flagman on a roadway overpass when a passenger car hit and ran through the barricade barrels. The car s
at approximately 1:00 p.m. on may 6, 1995, employee #1 was dismantling a tubular welded frame scaffold in howard beach, ny
employee # 1 was digging a hole by hand inside a 10 ft deep excavation. He was planning to roll a large boulder into the hole. W
two employees of a painting contractor were engaged in sandblasting the structural steel underside of a street bridge that pass
at approximately 11:15 a.m. on october 26, 1992, employee #1 was on a bridge platform that was approximately 110 ft above g


                                                       Page 81
                                                         all


employee #1 was using a gasoline-operated hoist to help two coworkers lift construction material to the 5th floor of a building. T
employee #1, a foreman, was on top of a plaster ceiling that was suspended from the roof by black iron. He was cutting the ver
an employee was using an electric snake to clean out a drain. The snake apparently had a ground fault, and the employee was
at approximately 8:30 a.m. on july 2, 1990, employee #1 was cutting steel beams that supported a structure known as part of th
while standing on a fiberglass ladder approximately 10 feet above an adjacent concrete work floor, employee #1 was connectin
at approximately 10:00 a.m. on march 9, 1992, employee #1 was on a structural beam, separating sheets of steel decking that
at approximately 9:20 a.m. on september 11, 1992, three dump trucks were being pulled backward up a steep incline by a john
employee #1 and another employee were working behind a 1989 mack concrete truck that was parked on a 15 degree inclined
at approximately 2:30 p.m. on may 17, 1993, employee #1, who had been leaning out an unguarded window wall opening to tal
the side glass panel of a caterpillar backhoe was removed by employee #1. Consequently, the employee was crushed to death
on march 5, 1993, employee #1 was inspecting the installation of overhead lighting for an electrician friend. He was in a basket
at approximately 10:45 p.m. on june 29, 1993, employee #1, operating a self-propelled aerial lift, drove the lift partway across a
employee #1, a 48-year-old iron worker, was working on a two point suspension scaffold 75 ft above ground level at bent 10. H
employee #1 was told to grade an area of soil with a 30-ton caterpillar bulldozer. The tracks of the dozer were frozen in the grou
at approximately 9:20 a.m. on january 25, 1994, employee #1, in an excavation 10 ft wide with depths up to 12 ft, was guiding th
at approximately 3:00 p.m. on february 11, 1995, employee #1, age 57, an employee of building erection specialists, inc., was w
at approximately 10:15 a.m. on march 11, 1995, employee #1 fell through a skylight that was not guarded and/or did not have a
at 8:48 a.m. on september 25, 1992, employees #1 through #5, three construction workers, were repairing a highway. The high
at 8:48 a.m. on september 25, 1992, employees #1 through #5, three construction workers, were repairing a highway. The high
at 8:48 a.m. on september 25, 1992, employees #1 through #5, three construction workers, were repairing a highway. The high
at 8:48 a.m. on september 25, 1992, employees #1 through #5, three construction workers, were repairing a highway. The high
at 8:48 a.m. on september 25, 1992, employees #1 through #5, three construction workers, were repairing a highway. The high
at approximately 12:00 noon on november 2, 1995, employee #1 had been hired by his best friend and a local plumbing contrac
at approximately 11:35 a.m. on october 27, 1995, employee #1 was nailing sheetrock from the top of an 8 ft wooden ladder whe
on county-owned property, a water storage tower had recently been erected and was being painted. Employee #1, a painter/bla
employee #1, a carpenter, was working 18 ft 2 in. above a cement floor without fall protection. He fell to the floor, striking his he
an electrician's helper was working about 5 feet above the floor on an 8-foot ladder. He was working on an energized circuit. A
a four-person crew was installing new utility poles along a road. The crew had installed a pole at an intersection the day before.
at approximately 1:25 p.m. on march 1, 1994, employee #1 left the cab of his truck and stood approximately 11 feet from the re
a power line worker was assisting a coworker that was in distress. The power line worker grabbed a 7200-volt power line to mo
at approximately 2:30 on november 29, 1995, employee #1 was in an 18 ft deep excavation fitting together sections of pipe for
employee #1 was struck by a vehicle. He sustained multiple injuries and died.
at approximately 7:00 a.m. on march 31, 1992, employee #1 and a coworker arrived at a job site in winston-salem, nc. the emp
at approximately 1:30 p.m. on january 13, 1993, employee #1 was working inside a trench that was approximately 8.5 to 9 ft de
at approximately 12:45 p.m. on december 31, 1992, employee #1, of thomas houck, was working on the roof of a three story ho
a power line worker was working on a wooden utility pole. His right shoulder contacted a 7200-volt overhead power line while h
at approximately 10:00 a.m. on may 18, 1995, employee #1, a mason's assistant at the job site for the construction of a private
employee #1 was at the hydraulic controls when the mast of an air trac drill fell onto him. He was struck on the back and killed.
employee #1 trimmed a limb from a wooden pole that a crane was loading onto a flatbed truck. He was returning his chain saw
employee #1 fell about 80 feet to the ground when the wire rope supporting a suspended scaffold broke. Employee #1 had disc
employee #1, an ironworker, fell from a steel beam onto an employee of another company who was walking beneath him. Both
employee #1, of ray bell construction company, was walking at ground level when an ironworker fell on him. Employee #1 and t
employee #1 was struck by lightning and killed instantly.
an employee was standing on a 10-foot-tall metal stepladder. He was using a portable electric tool plugged into an extension co
employee #1 fell 47 in. into an elevator pit. His arm was broken. He later died of complications.
employee #1 fell approximately 10 ft from a ladder, striking the back of his head on the asphalt. He was taken to a local emerge
on september 5, 1992, employee #1, of biocas and tucker digging service, a contractor, was working in an approximately 14 ft d
a painter was spray painting the east side of a condominium. A 7200-volt overhead power line was located about 15 feet from t
employee #1 and two coworkers were on a sand and debris platform that was secured underneath a bridge by hand winches a
employee #1, a part-time worker, was operating a john deere, model 2630, farm tractor with an attached scraper blade to grade
employee #1 and a coworker were hanging a light steel member approximately 60 ft above ground level. The employee had his
employee #1 was run over and killed when he walked up to a moving rubber-tired backhoe. The operator, unaware of employee


                                                      Page 82
                                                         all


employee #1 was working in an elevator shaft when the counterweight of the elevator came down, striking and killing him.
employee #1 fell approximately 20 ft while descending a ladder. He died.
employee #1 was riding on a powered industrial truck and fell off. He died from his injuries.
an apprentice electrician was working under a house, connecting circuit conductors in a junction box. The circuit had not been d
a painter was electrocuted when the aluminum ladder he was handling contacted a 12-kilovolt overhead power line.
on march 27, 1997, at approximately 12:30 p.m. employee #1 and employee #2 were preparing to rig a worker roof truss for ho
employee #1, age 19, was at a height of 115 ft installing antenna hardware and coaxial cable on a cellular telephone tower. Em
employee #1, age 19, was at a height of 115 ft installing antenna hardware and coaxial cable on a cellular telephone tower. Em
construction employees were working in a 12-foot trench when the trench caved in on employee #1, who was buried and later d
employee #1 was working at a construction job site picking up scrap metal and debris when he was struck by a steel i-beam an
employee #1 was oiling elevator cables when he fell and was caught between elevators. He died from his injuries.
employee #1, who was 50 years old, fell approximately 30 ft from the raised forks of a telescoping boom forklift. He died.
employee #1 was crushed and killed by a falling concrete tilt-up wall panel weighing 60 tons. It was a windy day.
employee #1 and coworkers were tearing down an existing building. All the workers were on the second floor. They had been u
two employees were removing a 7.6-meter-long ladder from the edge of a roof that was about 5.2 meters above the ground. Th
two employees were removing a 7.6-meter-long ladder from the edge of a roof that was about 5.2 meters above the ground. Th
an employee was installing rain gutter along the edge of a canopy. As he was lifting a 7.3-meter-long (24-foot-long) section of g
employee was using a truck crane to lift a compressor motor out of the basement of an existing building. The boom of the cran
employee #1 was in the basket of an inspector 50 truck, painting a gas pipeline that ran under a bridge. He got out of the baske
the carpenters wer walking down the closed exit ramp to their personal vehicle (pickup truck) to get their tools when a dump tru
an employee was installing a piece of sheet metal as part of a return air system. He was using a makita cordless screw gun to
an employee was installing sheet metal work for a return air system. He placed the sheet metal across the floor joists and used
employee #1 was applying sealer to a sawed groove in highway pavement for a traffic signal sensor. A motorist, ignoring the tra
employee #1 and a coworker were working in an excavation. The backhoe operator was positioning the bucket to hold a coring
an electrician was working under a house rewiring some circuits. He cut into an energized conductor and was electrocuted.
employee #1 was painting and scraping the exterior window and gutter of a building. He fell from a 40 ft scaffold and was killed
employee #1 was pushing a wheelbarrow on the fifth floor of an unfinished high-rise construction project. His job was to clean u
a power line worker was working from an aerial lift, repairing a connection at a utility pole. He was shortening a stinger wire. Wh
the employee was performing drywall finishing work while wearing stilts (3' high). The employee stumbled and struck his arm ag
fatality
employee #1 was using a track backhoe to remove a tree. When pressure was applied to a small tree, a large tree fell on top o
employee #1 either fell from scaffold platform or from access way while assisting masons in final clean up of scaffold work. Thr
employee was placing metal roofing onto roof when he accidently stepped onto the roof insulation instead of the metal roof and
employee #1, a backhoe operator, had stopped at an old dumpsite to bury a dead cat for the town's police department. He lean
on january 29, 1992, employee #1 and two coworkers were erecting 8 ft by 24 ft 11 in. pre-stressed concrete wall panels. They
at approximately 7:30 p.m. on july 1, 1991, employee #1, age 16, was laying a 4 in. by 10 ft length of drain pipe in a 40 ft long b
employee #1 was hauling dirt in the bucket of a loader/backhoe to fill small depressions in the ground around the concrete cons
concrete was being poured in forms that were about 10 ft above a platform at the ladder access area. An fmc link belt crane, m
a group of five employees finished sweeping a concrete bridge deck on a highway. Employee #1 was standing next to the curb
employees were cleaning cracks in a highway for a contractor to seal. They were changing the zone (work area). One employe
an employee was installing sheathing on the roof of an addition to a house. The employee was struck by lightning and was elec
at approximately 8:20 a.m. on august 8, 1992, employee #1 and a coworker were preparing to cut concrete for sealing. Employ
a two-person crew was setting utility poles. The existing overhead power line had been offset to the north with fiberglass tempo
at approximately 12:45 p.m. on june 3, 1996, employees #1 and #2 and a coworker were preparing to grind off pavement mark
at approximately 12:45 p.m. on june 3, 1996, employees #1 and #2 and a coworker were preparing to grind off pavement mark
an employee of a concrete contractor hauled forms to a job site in a dico-side-o-matic concrete block truck. The boom on the tr
a crew of four employees were repairing and rotating spouts on a bucket grain elevator leg. To get a crane close enough to the
construction workers were building new steeps. A passenger elevator, montgomery 207 e, serial #7915, located in the corn tow
employees #1, #2 and #3 were attempting to move a mobile home from point a to point b. employees #1 and #2 were attemptin
on 7/16/99, at approximately 3:20 a.m. employees #1 and #2 proceeded to jump a battery on a street sweeper so as to get the
on august 27, 1996 at approximately 4:30 p.m. employees #1, 2, 3 and 4 were preparing to move overhead distribution power l
an employee was operating a truck crane. He moved the crane's boom out to pick up a 10-foot section of an elevator leg. A sec


                                                     Page 83
                                                        all


employee #1, operating a d-7 dozer with full cab, was constructing a causeway into a river; the causeway would be used to plac
two coworkers of employees #1 and #2 were moving an excavator 7 to 8 miles on an interstate highway to the next job site. On
two coworkers of employees #1 and #2 were moving an excavator 7 to 8 miles on an interstate highway to the next job site. On
at approximately 7:00 p.m. on june 9, 1995, employees #1 through #4 were in a trench 23 ft long, 4 ft wide, and 10 ft 2 in. deep
at approximately 7:00 p.m. on june 9, 1995, employees #1 through #4 were in a trench 23 ft long, 4 ft wide, and 10 ft 2 in. deep
at approximately 7:00 p.m. on june 9, 1995, employees #1 through #4 were in a trench 23 ft long, 4 ft wide, and 10 ft 2 in. deep
at approximately 7:00 p.m. on june 9, 1995, employees #1 through #4 were in a trench 23 ft long, 4 ft wide, and 10 ft 2 in. deep
at approximately 10:30 p.m., employee #1 parked his pickup, with flashers on, at the edge of the northbound lanes on i-35 and
employee #1 was putting wood under the wheels of a volvo tractor trailer when the trailer hitch came down on his head. Employ
a power line crew was stringing new conductors along an existing right of way. A power line worker on the crew had backed a d
employee #1, age 20, was moving dirt when he began to feel ill from the heat. He was taken to keokuk community hospital suff
at approximately 1:10 p.m. on september 28, 1992, employee #1 was helping to repair a dam located on a farm pond. He was
at approximately 8:45 a.m. on november 17, 1992, employee #1 was using a ramset powder-activated tool to refasten bridge d
at approximately 5:30 p.m. on january 12, 1994, employee #1 was laying pipe in a trench that was 10 ft deep, 20 ft long, and ap
at approximately 4:15 p.m. on march 1, 1993, employee #1 was helping install tie-off brackets for an elevating work platform to
at approximately 11:30 a.m. on march 29, 1994, employee #1 was changing attachments on a loader. He had removed the buc
at approximately 11:30 a.m. on january 27, 1993, employee #1 was operating a dump truck on a county road. He was on the no
at approximately 9:00 a.m. on october 8, 1993, employees were clearing debris from a job site. A bobcat rubber-tired skid loade
at approximately 9:45 a.m. on or about september 11, 1990, employee #1 drove a forklift truck from the shop, where he had be
at approximately 1:45 p.m. on november 15, 1990, employee #1, of quality plus roofing, who was working on an 8:12 pitched ro
employee #1 was operating a vibratory roller smoothing the new dirt road surface and compacting it in preparation for graveling
at approximately 7:30 a.m. on april 3, 1991, employee #1 was at a construction site in stayton, or, placing traffic warning device
employee #1 was using a d5c caterpillar bulldozer to push rocks into an excavation when he lost control of the vehicle. It rolled
at approximately 1:26 p.m., employees #1 and #2 were working on top of a white liquor tank installing a blank into a line that ha
at approximately 1:26 p.m., employees #1 and #2 were working on top of a white liquor tank installing a blank into a line that ha
at approximately 1:26 p.m., employees #1 and #2 were working on top of a white liquor tank installing a blank into a line that ha
at approximately 1:26 p.m., employees #1 and #2 were working on top of a white liquor tank installing a blank into a line that ha
employee #1 was taking measurements from the top of a 23 ft high fiberglass storage tank. Before taking the measurements, t
at 3:15 p.m. on or about september 17, 1997, a crew had finished a portion of a trench. One backhoe operator attached the alu
on or about 06-02-98 the grader operator was in the process of grading a new road into a residential sub division. He heard a n
on or about august 7, 1998 at approximately 10:35am, the victim drove a water truck with a tilt trailer to a staging area. When th
at approximately 1:45 p.m. on june 28, 1993, employee #1 was sheeting a roof that also required skylights to be installed. The o
two roofers were in an aerial lift, working on the edge of a roof at an apartment building. As they were working, the roofer who w
two roofers were in an aerial lift, working on the edge of a roof at an apartment building. As they were working, the roofer who w
at approximately 9:20 a.m. on october 5, 1993, employee #1 was engaged in a maintenance operation at the asphalt plant. Dur
at approximately 11:50 a.m. on october 25, 1993, employee #1 was assigned to climb a ladder 20 feet to a roof and drill holes i
employee #1 had propped open the tailgate of a dump truck to prepare the steel bed liner for welding. After placing a 37 1/2 in.
at approximately 3:30 p.m. on december 13, 1994, employee #1 and a coworker, of b & g excavating, inc., were working on a s
at approximately 1:30 p.m. on april 12, 1995, employee #1, of canby excavating, canby, or, was using a 1981 a-62 front end loa
at approximately 11:25 a.m. on june 15, 1995, employee #1, a mechanic's helper, was removing the front rear differential of a d
two ironworkers were working on a concrete and structural steel building under construction. Both workers were on a partially d
employees were dismantling a storage rack while one employee was working out of a single man man lift. The man lift toppled
on october 8, 1997 employee #1, 36 years of age with 1.5 years of experience in his position, was fatally injured when struck al
on the morning of august 7, 1995, employee #1's throat was apparently cut by a skilsaw. He was killed. There was a blood cove
employee #1 was riding on the back of a flatbed truck that was traveling at approximately 4 mph when he fell 41 in. onto the as
on october 4,1993 at about 10:45 am employees #1 and #2 were in a trench to chip off a portion of cement from an existing pip
on october 4,1993 at about 10:45 am employees #1 and #2 were in a trench to chip off a portion of cement from an existing pip
employee #1, age 39, was helping his brother-in-law, owner of collin electric, take down fluorescent lighting fixtures. He was sta
employee #1, age 20, was part of a framing crew that was working on the fourth floor roof. Three runs of 4 ft wide plywood had
employee #1 was a janitor and night security guard for terry tile company in los angeles. His employer provided sleeping quarte
employee #1 and coworkers were cutting trees and shrubs between the freeway and a city street, clearing the area for a retaini
at about 2:45 p.m. on march 30, 1991, employee #1 was found lying unconscious on some stairs in a townhouse under constru


                                                     Page 84
                                                         all


an electrician and his employer went to a house where they had installed the wiring several months earlier. They were there to
all of the pertinent facts regarding this fatality are in file s6062-119-91 r4 d5 inspection no 112216767 12-0690. The employer in
at about 0815 hours on 6 december,1990 mr leyva was hanging drywall in a tenant improvement type construction project at 90
employee #1, an apprentice carpenter, was removing falsework from underneath a freeway connector under construction. The
worker was functioning as fire watch for welding operations he was observed sitting and then standing on a 6' step ladder. It po
deceased was removing nuts holding concrete sound barriers along freeway the nuts were to be removed in sequence and last
an electrician was working on a 480-volt transformer, installing metal conduit for a service extension from the transformer. He t
on october 7, 1994, employee #1 had been at a site alone, finishing sweeping debris from the roof. A neighbor found him dead
at approximately 12:30 p.m. on december 6, 1994, employee #1 was working from a metal rolling scaffold approximately 8 ft 3
an employee of a concrete drilling and sawing contractor was operating a concrete drilling machine at a manhole at a college c
at approximately 1:40 p.m. on november 16, 1990, employee #1, of kasber corporation, san bernadino, ca, was at a constructio
at approximately 8:00 a.m. on august 16, 1990, employee #1, a foreman for herzor electric, inc., was approximately 30 ft above
on february 20, 1991, employee #1 was helping his brother frame additional rooms at his home in los angeles. Employee #1 wa
employee #1 was driving a ford 600 gallon water tanker truck, serial #k90fvm32291, down a dirt road at a construction site. He
employee #1 was raking gravel behind a 10-yard dump truck. He was out of view of the driver, who was backing up to the grave
at approximately 1:15 p.m. on december 7, 1990, employee #1, a laborer, was the ground man on a scaffold removal team. He
at approximately 2:30 p.m. on may 17, 1991, employee #1, a part-time laborer, was preparing an excavation for relocating trees
a grove rough terrain crane (model number rt49) was lifting a 30-foot section of rebar into position during the construction of a s
a grove rough terrain crane (model number rt49) was lifting a 30-foot section of rebar into position during the construction of a s
the deceased was working on the metrorail project for tutor saliba, was working below surface at station level. Assigned to build
employee #1, a lineman, was assigned to drill holes at the top of transmission line poles for the cable supports of the crossarm
on december 27, 1990, employee #1 and a coworker were assembling the scaffold shoring before pouring concrete for the top
employee #1, a carpenter, was sheathing the roof of a single-family house. There were three skylight openings on the flat portio
employees #1 and #2 were preparing to lay out the foundation of an 8 ft retaining wall for a single family house under construct
employees #1 and #2 were preparing to lay out the foundation of an 8 ft retaining wall for a single family house under construct
at about 4:30 pm on august 21, 1990, employee #1 was laying 40-pound roofing paper, 22 feet above the ground, on a 6:12 pit
at approximately 2:15 p.m. on july 24, 1991, employee #1, an electrical technician, was carrying a 30 lb canister of freon gas up
at approximately 2:45 p.m. on december 18, 1990, employee #1, a welder with 12 years of experience as an ironworker, was w
employee #1, a carpenter, was framing a building at a small shopping center. He was standing on a beam and on a 4 in. ledger
at approximately 9:00 a.m. on january 23, 1992, employee #1 was helping move a 66,867 lb falsework platform built around a b
at approximately 1:30 p.m. on june 19, 1992, employee #1 was standing near a 9,600 lb winch, providing tag line service with a
a journeyman electrician was working at a 5000-square-foot building under construction. He was going to feed a mouse through
employee #1, of a.l. & m. plumbing co., had been installing plumbing in a building at a construction site. He exited the building a
an electrician for a sign maintenance company was assigned to work on an electric, lighted pylon sign at about 9:30 am. The el
employee #1's employer was unknown; it is suspected that he was working for himself. Orange county fire department paramed
employee #1, of ball ball & brosamer, inc., was performing work at a center divider of a freeway at night. Two freeway lanes on
employees #1 and #2, of john dodd co., inc., were working from the bucket of a front end loader approximately 20 ft above the
employees #1 and #2, of john dodd co., inc., were working from the bucket of a front end loader approximately 20 ft above the
employee #1, a truck driver for irish construction, was experiencing motor problems with a truck he was driving. He stopped the
employee #1 and a welder were performing work inside a section of 27 in. pipeline that was under construction. The welder wo
a free-standing section of chain link fence at a construction jobsite was leaning against a metal trailer. The frame of the trailer h
at approximately 8:47 am on november 17, 1990, employee #1, of the nutralite vitamin manufacturers, was in an elevated aeria
employee #1 was in an approximately 16 ft deep excavation, installing a drain line with his foreman. The foreman was ascendin
employee #1, of nelson and belding construction corp., was checking the grade in a benched, 5 1/2 ft deep trench. He had finis
employee #1, an excavator operator, was assigned to remove an area of very wet soil and mud from an area that had been dra
employee #1 was working atop a platform elevated approximately 10 ft by a forklift. The unsecured platform came off the forklif
employee #1, a laborer, was removing pins from the metal forms of a concrete wall that had been poured the previous day. He
at approximately 11:45 p.m. on october 13, 1990, employee #1, a mechanical supervisor, was working on a well water supply s
employee #1 was working as a temporary hod carrier for giulinani bros. His job was to mix and carry mortar to a stone mason.
at 3:30 p.m. on june 29, 1990, the second shift had just started working at the napa pipe plant in napa, ca. Employee #1, an ins
at about 8:00 a.m. on may 13, 1991, a 3-man dalton construction co. crew, including employee #1, a laborer, were cleaning, un
on october 10, 1991, employee #1 was discovered dead with multiple blunt injuries to the head at a residential construction site


                                                      Page 85
                                                         all


on november 1, 1991, employee #1, nominally a subcontractor to munkdale bros., showed up for work at a construction job site
at approximately 2:00 p.m. on october 15, 1990, employee #1, of r. kopp painting services, was on an extension ladder painting
an employee of a roofing contractor working at a jobsite in alameda, ca, was fatally injured in a fall from a 21-ft high sloped roof
an employee of a roofing contractor was fatally injured while working at residential jobsite in oakland ca. He fell from the roof du
on july 25,1990 at approximately 9:45 am 3 electrical workers, employees #1 and #2 and #3 were seriously burned by an electr
on july 25,1990 at approximately 9:45 am 3 electrical workers, employees #1 and #2 and #3 were seriously burned by an electr
on july 25,1990 at approximately 9:45 am 3 electrical workers, employees #1 and #2 and #3 were seriously burned by an electr
at about 4:00 p.m. on july 26, 1990, in los angeles, ca, employee #1, age 19, a painter employed by oscar's painting, inc., was p
employee #1, of roof maintenance, inc., was demolishing roofing materials and a birdhouse on a roof when a trap door opened
employee #1, a new and inexperienced roofing contractor employee, was assigned to do ground work. While unsupervised, he
employees #1, #2, #3, and #4 were employed by kasler corporation as carpenters under the supervision of a foreman. Their job
employees #1, #2, #3, and #4 were employed by kasler corporation as carpenters under the supervision of a foreman. Their job
employees #1, #2, #3, and #4 were employed by kasler corporation as carpenters under the supervision of a foreman. Their job
employees #1, #2, #3, and #4 were employed by kasler corporation as carpenters under the supervision of a foreman. Their job
employee #1, a roofing foreman with allstate roofing, was laying composition roofing paper on a sloping roof. The paper was fo
between 10:30 a.m. and 3:45 p.m. on may 18, 1992, employee #1 drove a case construction king 680h over a cliff at a job site,
on july 23, 1992, employee #1, of western oil spreading, inc., was driving a hyster pneumatic compactor (c530a) on a private dr
employee #1 was a ground laborer, whose job did not involve picking or putting down road markers (reflectors) during the re-su
three employees were replacing the roofing on a single family house. One of the employees, the owner of the roofing company,
an elevator installer was cleaning up after a job. The door opening equipment module accidentally contacted a 240-volt circuit p
at approximately 12:00 noon on september 6, 1990, employee #1 was performing an electric welding operation on a steel colum
on february 22, 1991, employee #1 was operating an 82-ton link-belt crane adjacent to the median of highway 110. After a conc
an employee of a framing contractor was erecting a house. He was assisting a crane operator in rigging a stack of plywood tha
a 35-year-old electrician working as an independent contractor was installing wiring in a room in a residence. He had been work
at approximately 11:55 a.m. on january 22, 1991, employee #1, a carpenter with valley construction company, was using a rollin
employees #1 through #5 were working on the roof of a structure at a construction site. The roof collapsed under a load of mate
employees #1 through #5 were working on the roof of a structure at a construction site. The roof collapsed under a load of mate
employees #1 through #5 were working on the roof of a structure at a construction site. The roof collapsed under a load of mate
employees #1 through #5 were working on the roof of a structure at a construction site. The roof collapsed under a load of mate
employees #1 through #5 were working on the roof of a structure at a construction site. The roof collapsed under a load of mate
at approximately 9:00 a.m. on december 26, 1990, employee #1, of harris painting company, was painting on the third floor of a
an independent electrical contractor was working inside a 480-volt cabinet at a beverage company. An electrical fault in a circui
on august 10, 1990, employee #1, a laborer-foreman with about 15 years experience, was working for malcolm drilling co., inc.,
on august 15, 1990, employee #1, a 32-year-old electrician for hyundai mega electric company, and a helper were installing ele
at approximately 9:30 a.m. on february 1, 1991, employee #1 was climbing a 10 ft ladder. He was holding onto the rungs with o
at about 6:10 p.m. on april 27, 1992, employees #1 and #2 were putting up traffic warning signs on a southbound lane of the lon
at about 6:10 p.m. on april 27, 1992, employees #1 and #2 were putting up traffic warning signs on a southbound lane of the lon
at approximately 10:20 a.m., after the morning coffee break, employee #1 resumed work on the southwest corner of the upper
at approximately 9:30 a.m. on may 3, 1991, employee #1 and two coworkers were installing a steel channel and beam in a bric
employee #1, an air conditioner repairman, went alone to a single story building housing small businesses to make an estimate
a well drilling rig operator was fatally electrocuted when herraised the boom of the rig up into a 12,000 volt power line. See narr
at approximately 11:30 p.m. on april 6, 1991, employee #1 was installing 4 ft by 8 ft by 3/4 in. sheets of plywood on a roof. He w
at approximately 1:15 p.m. on september 6, 1992, employee #1, of c.t. williams construction, was working on a 40 ft by 24 ft me
at 6:00 a.m. on july 25, 1991, employee #1 was assigned by his superintendent to find a damaged pvc conduit. The superintend
a five-worker crew working for a power line contractor had poured a 12-foot-by-16-foot concrete pad for the installation of a new
at approximately 11:45 a.m. on january 6, 1992, employee #1, of yuma sprinkler and pipe company, entered a 2 ft wide by appr
at approximately 3:00 p.m. on september 17, 1990, employee #1 was pulling fish tape wire through a curtain wall in a warehous
employee #1 was crushed and killed when a 13,000 lb, 36 in. diameter by 80 ft long steel pipe broke from its perch and rolled o
at approximately 10:02 am on december 3, 1990, employee #1, the job foreman, was moving and adjusting the position of oran
don hegg electric sic 1731 the employer's firm had been moved by a mobile home owner to determine rason the owner was ge
on september 5,1990 at approximately 9:15pm,employee #1 the repairman involving the repair of 10'x10' roll up clock doors wa
b and g sheet metal inc sic 1761 the employee was working on an elevating work platform attaching a sheet metal fir curtain to


                                                      Page 86
                                                        all


gaylor gren sic 1796 the employer hired the two employees to lower conveyors and remove the from an abandoned concrete ba
gaylor gren sic 1796 the employer hired the two employees to lower conveyors and remove the from an abandoned concrete ba
on september 13,1990 at approximately 12 noon, the contractor's crew was performing a chip seal operaton on h/w 49 3 miles
on 10/19/90 at 10:35am (approx) a 15 ton p&h (omega 15) hydraulic mobile crane with telescopic boom (62ft) tipped over on te
on 12/18/90 at about 9:50am a laborer, for he employer was found at the 2nd floor north exterior balconey bleeding profusively
employee #1 was inside an excavation at a sewage plant using an acetylene torch to cut a pipe. The pipe was leaking oxygen a
employee #1 was inside an excavation at a sewage plant using an acetylene torch to cut a pipe. The pipe was leaking oxygen a
ross & sons refrigeration inc trained experienced leadman working on metal roof 17'8" high, installing/aligning 3 1/2" imc ridged
on april 7,1991 at about 8:20 hours employee #1 and #2 were working with a crew positioning the first steel plate of the third rin
on april 7,1991 at about 8:20 hours employee #1 and #2 were working with a crew positioning the first steel plate of the third rin
on december 26,1995 at approximately 11:30 am an accident occurred at 4 so main street, bishop ca 93514. Employee #1 was
at approximately 8:30 a.m. on may 16, 1991, employee #1 was standing on the bed of a concrete pumping truck, pumping conc
at approximately 2:00 p.m. on october 25, 1991, employee #1 was helping a journeyman carpenter cut an approximately 107 in
on tuesday the 19th day of march 1991 an employee of owen pacific, a roofing company, was fatally injuried when to slid from t
(homestead land development-1521) on february 14, 1991 at 9:14am, employee #1 was found apparently dead at the foot of th
at approximately 3:55 pm on december 26, 1990, employee #1 sustained serious injuries when the trench in which he was wor
employee #1 sustained massive head injuries and later died after fall ing 24' into a concrete pit. The incident occurred at the sh
on 02-12-91 at about 8:30am an accident occurred at the zond wind energy park 13000 jameson road tehachapi ca emloyee #1
at approximately 3:30 p.m. on december 20, 1993, employees #1 and #2 and a coworker were painting the side of a building in
at approximately 3:30 p.m. on december 20, 1993, employees #1 and #2 and a coworker were painting the side of a building in
at approximately 10:00 a.m. on october 8, 1994, employee #1 was working with two other workers. A suspended scaffold was s
at approximately 10:00 a.m. on october 25, 1995, a crew from anderson roofing and sheet metal co. was preparing for roofing w
employee was operating a mobile crane, outfitted with a wrecking ball, doing demolition work on a concrete-reinforced, steel fra
on 5/15/97 at approximately 11:35 am, k j woods construction co. was excavating at the intersection of union & larkin streets pe
on 5/15/97 at approximately 11:35 am, k j woods construction co. was excavating at the intersection of union & larkin streets pe
on 7/19/97, three (3) employees #1, #2 and #3 were painting a house at 68 josiah st., san francisco, ca 94112. These employe
on 3/4/99 at about 3:15 p.m., I responded to a fatal accident. The deceased had worked as journeyman carpenter for largo con
a foreman for an electrical contractor had access to a switchyard belonging to an electric utility. One weekend, on his own time
on august 12, 1984, employee #1 was hired by the mendocino county public works department as an equipment operator I. he
employee #1 was assigned to help his employer install delineators at the median strip of the 101 freeway, slightly north of the 5
on november 8, 1990, employee no. 1, was working on the installation of a primary distribution alarm circuit (pdac) switch on po
on may 17, 1994, at about 7:30 am, raymond worley and another employee, jeff soria, climbed to the roof of a wood-framed ho
on november 27, 1990, employee #1 and a helper, of gen con services, were installing solid wood doors, weighing about 100 lb
on november 28, 1990, employee #1, of leo j. vandervennet co., placed a metal mortar box on a 3 ft by 3 ft wooden pallet. He p
on october 24, 1990, employee #1 was filling a form oil tank that was under approximately 80 lb of pressure. He did not release
employee #1, of banghart excavating co., was standing behind a backhoe and was going to put in pins in order to keep the boo
on october 8, 1990, employee #1 was on the 30th floor of the eastbank towers signaling a tower crane to pick up forms from co
on october 19, 1990, employee #1 was a member of a crew of six employees that was erecting a scaffold. Employee #1 was w
employee #1 and another employee were working from a fully decked work platform located approximately 20 feet above the g
employee #1 and another employee used the stairs on the south side of a building under construction to ascend to the fourth flo
employee #1, of cook jackson contracting, was using a powder actuated tool to install fasteners through metal decking and into
employee #1 and a coworker of the george kountoppes painting co., were working from a swing-stage scaffold approximately 3
on july 17, 1991, beech construction was removing and replacing a 10 inch high pressure gas main. After consumers power sh
on october 8, 1991, employee #1 and two coworkers, of peter a. basile sons, inc., were stringing a line from the new driveway p
on july 23, 1991, a pneumatic mole had been pushed under the road for a 2 in. conduit. The mole apparently hit a rock and wen
on august 22, 1991, a crew of six was doing new maintenance roofing on a warehouse. Employee #1 was walking backward w
on october 8, 1991, employee #1, of the manistee county road commission, was operating a case 1085-b cruz-air backhoe exc
on november 1, 1991, employee #1 was working alone on a mobile scaffold that was 5 ft 10 in. high. While removing material f
on november 12, 1991, employee #1 and a coworker were power washing and removing paint from the interior concrete surfac
on december 23, 1991, at the construction site of an excavation at southgate, mi, six employees of davada construction were in
on january 8, 1992, four employees of concepts in carpentry began work by loading a tab-built platform, which was being used
on february 13, 1992, three employees of upper peninsula power co. were to replace five wooden poles. One employee drove t


                                                     Page 87
                                                         all


on june 18, 1992, the crew from the oakland county road commission was dispatched to clean ditches for drainage. The crew w
three employees were installing rain gutter on the east side of a two-story farm house. The eaves on the house were 18 feet ab
three employees were stringing a new overhead power line on new utility poles adjacent to an existing line. During this job, the
on april 6, 1992, employee #1, of schiffer mason contractors, was working with a crew to lay up a block wall at the north stagew
at about 7:00 a.m. on march 31, 1992, a three-man crew began work on the roof of the capitol. The project had started the day
on the morning of june 29, 1992, employee #1, of rumsey & sons, and five coworkers were installing a water main. After they in
on december 29, 1994, employee #1 was flame cutting a section of steel pipe in preparation for shipment. The section was app
at 10:45 a.m. on february 14, 1994, a crew of five roofers was on site to clean snow off a roof and to install metal coping. While
at 2:10 p.m. on march 23, 1995, a three man crew was repairing a damaged underground roof drainage pipe. Employee #1 clim
at 4:55 p.m. on march 23, 1995, employee #1, of rmf inc., and another boilermaker were assigned to repair boiler tube membra
a six-person crew arrived at a jobsite, but the weather conditions did not allow them to perform their anticipated job of installing
a six-person crew arrived at a jobsite, but the weather conditions did not allow them to perform their anticipated job of installing
on april 13, 1995, two men were working on the roof of a best buy store, installing blocking on top of the parapet wall. Employee
a three-person power line crew was installing new crossarms on a 4800-volt, three-phase delta overhead power line. The crew
between 4:00 p.m. and 5:30 p.m. on april 13, 1995, employee #1, of dan's excavating, was using a bulldozer to build a berm at
at approximately 12:45 p.m. on july 13, 1995, employee #1 was part of a five-man crew cleaning and patching a section of pave
at 4:35 p.m. on june 15, 1995, employee #1 and a coworker, working for the city of ann arbor, were changing light bulbs in the t
on november 8, 1994, employees of oscar larson started an excavation. On november 11, 1994, employee #2 and a coworker
on november 8, 1994, employees of oscar larson started an excavation. On november 11, 1994, employee #2 and a coworker
a two-person crew arrived at a job site to put an addition onto a house. They placed a 40-foot-tall aluminum ladder on the groun
on friday, october 16, 1992, employee #1, of ferguson electric co., was assigned to install wall-mounted outdoor light fixtures in
an electrician was working on a newly installed 277-volt, three-phase lighting system. He was instructed to install a junction box
on october 28, 1992, employee #1, of lewis steel co., was to remove splice plates from crane rails and replace them with new s
on april 16, 1993, employee #1, of key construction inc., was operating a 10-yard asphalt dump truck on highway 131. The truc
a power line crew was replacing a utility pole. The existing pole was broken. The crew had apparently placed the new pole and
on september 24, 1992, employee #1, of dynamic painting corporation, was a member of a crew that was abrasive blasting and
on october 2, 1992, employees #1 and #2, of edgar boettcher masonry, were at alma college working on a 46 ft high htk. mast
on october 2, 1992, employees #1 and #2, of edgar boettcher masonry, were at alma college working on a 46 ft high htk. mast
on october 5, 1992, employee #1 and a coworker were assigned to pick up a caterpillar 977 tracked front end loader to be load
at 8:00 a.m. on december 1, 1992, a raising gang from arco steel, inc., started work. At 9:55 a.m., employee #1 was erecting st
on november 6, 1992, employee #1 and two other laborers, of tony angelo cement construction, were assigned to start preparin
on october 21, 1992, employee #1 was working in a grit chamber measuring 72 ft long by 12 ft wide by 20 ft deep. The access
on march 29, 1993, employee #1, of grand tower inc., was part of a crew erecting a communication tower. 140 feet of the tower
on june 2, 1993, employee #1, of statewide excavating, inc., was one of five employees installing sewer and water service. He a
a three-person power line crew was replacing armor rods on the phase and neutral conductors of a 4800-volt overhead power l
on june 25, 1993, employee #1, of pamar enterprises inc., was a member of a crew installing sewer pipe for a residential subdiv
employee #1 was part of a seven man crew erecting structural steel for a new k-mart addition in cheboygan, michigan. Employe
on august 15, 1993, employee #1 was on his first day on the job at piedmont excavating, inc.; he was to assist in shooting grad
on august 28, 1993, employee #1, a site supervisor for rosentreter excavating, was laying pipe in a trench. A six inch diameter
on september 17, 1993, employee #1, of dan's excavating inc., a laborer on a sewer construction crew, entered a 26 ft deep ma
on october 22, 1993, employee #1, a dump truck driver for cadillac asphalt, was delivering approximately 6 tons of paving mate
a carpenter was the ground hookup worker for a p&h rt40 crane on the north side of a building under construction. The carpent
a journeyman electrician was installing a bus drop cable into an existing panelboard supplying electric power to a press. He ope
two steel workers were acting as ground men for the unloading of eight tractor trailer loads of material for a pre-engineered buil
two steel workers were acting as ground men for the unloading of eight tractor trailer loads of material for a pre-engineered buil
on november 9, 1993, employee #1, an ironworker with pioneer construction inc., was setting precast concrete floor planks on t
a drywall finisher was working alone, using his own tools to perform his normal work. He was using an electric drill with a paddle
on october 7, 1993, employee #1 of lemaster steel erectors was installing a standing seam metal deck roof on a 180 foot by 13
at 3:00 p.m. on december 20, 1993, employee #1 of skylink communication inc. was installing a midway point beacon light on th
on february 15, 1994, employees working for carl e. smith were loading steel flume pipe and swamp mats onto semi-trailers. Th
on 3-4-94 a crew from stanson wrecking returned to a job site in rose- ville under the supervision of vito reuienius (v.p. of comp
two electricians for an electrical contractor were performing maintenance on a marquee sign at a store. While they were workin


                                                      Page 88
                                                         all


mr kaiser was part of a four man crew doing sanitary sewer construction. He was one of two pipelayers working in the trench. T
a 48-person crew for an electrical contractor was working on a major renovation of an automobile plant. One of the crew memb
a power line crew for an electric utility was repairing a fire-damaged substation. The power lines in the substation were deenerg
on 7/18/94 at 3:30 pm mr roberts was the foreman for the plumbing contractor working on the construction of a retail store. The
a three-person power line crew was transferring a 4800-volt overhead power line from an old pole to a new one. An apprentice
two crew members contractor took the survey (skiff) boat out about 1/4 mile to their barge in little traverse bay. They did some w
two employees (a brother and sister) were erecting a new flagpole at a post office. The 28-foot-long aluminum flagpole contacte
two employees (a brother and sister) were erecting a new flagpole at a post office. The 28-foot-long aluminum flagpole contacte
on august 16, 1994, employee #1, a carpenter, was installing plywood floor sheeting during the construction of a new house. An
mr sanchez-gonzales was a laborer working on a road seal project. He was riding in the back of a pick up truck while placing pa
mr nauta was part of a three man crew doing final grade work on a street resurfacing project. He was doing hand grading aroun
a power line crew was making final connections for an extension to a single-phase, 4800-volt overhead power line. They had m
a pipe-laying crew was installing a new water main. They used a backhoe to lower a 12-inch-diameter ductile iron pipe into a 6-
at 10:00 a.m. on december 8, 1995, a four-man crew at the midland co. had removed usts and was cutting openings in them. E
on october 5, 1995, a crew of bricklayers and laborers that included employee #1 was working at the commons building from a
several employees of different contractors were building a pole building. A three-phase, 11-kilovolt overhead power line was loc
at approximately 12:30 p.m. on november 6, 1995, employee #1, a member of a two-man crew from lewis roe excavating, was
at 10:30 a.m. on november 1, 1995, employee #1, a laborer for pett construction, and a coworker were setting trusses. They we
at 5:00 p.m. on september 22, 1995, employee #1, of l. d'agostini & sons, was part of a three- or four-man crew that was jackin
on august 26, 1995, a benson roofing (a.k.a. grand six construction) four-man crew, working on an approximately 112 ft by 326
at 9:10 a.m. on february 13, 1996, two city of saginaw workers arrived at a job site to repair a water main. They parked a backh
employee age 69 on march 8, 1996 a three man crew painting a new house in holland, mi were in the process of covering the s
fall - iron worker - commercial date of accident: 5-1-96 employer: reddinger steel erectors inc. the deceased: age 41 sic code:
on february 17, 1994, employee #1, of the james martin building, was on his way to remove snow that had accumulated on a ro
on april 1, 1994, employee #1, of j.k.m. enterprises, inc., was standing between a hi-lo and a truck bed. The hi-lo operator start
on june 22, 1994, employee #1, a diver, was inspecting the draft tubes under a hydro-electro dam. The turbine had not been loc
on june 16, 1994, employee #1 was lying under a semi-trailer that was hooked to a running tractor. He was working on the brak
on july 23, 1994, employee #1, a general landscape laborer, was listening for leaks in the air brake system on a truck. He was o
employee #1, a general laborer and maintenance worker for michigan colprovia co., was inside a hopper attempting to loosen s
on november 4, 1991, employee #1, of robinson construction co., was working under the elevated box of a dump truck. The tru
on february 25, 1992, employee #1, of matico drilling company, was operating a hi-tech model #75 drilling rig taking soil sample
on july 29, 1993, employee #1, of the eaton county road commission, was assisting a tree cutting crew near a roadway. A crew
on august 5, 1993, employee #1, of the jackson county road commission, was walking on the side of the road alongside a dum
on february 26, 1990, employee #1, age 39, of the michigan department of transportation, and an employee of erco corp. (Mid w
on february 26, 1990, employee #1, of erco corp. (Mid west bridge), and an employee of the michigan department of transporta
on march 5, 1990, employee #1, of sydney rosenberger insulation and home builders, was instructed to finish placing drywall ar
a power line crew was placing a recloser into service on a 13.2-kilovolt overhead power line. A test group at the control panel o
on february 9, 1990, employee #1, age 42, and five other employees of the rochester division of general motors were on a roof
on april 28, 1990, employee #1, of command helicopters, inc., was the pilot of a helicopter being used to lift communication equ
a power line work crew was stringing an overhead power line. The new line was being installed over an existing 4800-volt line. T
on july 8, 1990, employees #1 and #2 were cleaning the exterior of a building from a swing stage scaffold at the eleventh floor.
on july 8, 1990, employees #1 and #2 were cleaning the exterior of a building from a swing stage scaffold at the eleventh floor.
at 1:00 p.m. on june 15, 1990, employee #1, a boiler maker for songer corp., was part of a crew that was hoisting material for s
a four-person crew was installing a current transformer on a 4160-volt power line. The work was to be performed deenergized.
on july 15, 1990, employee #1 and a crew, of songer corp., were welding inside a vessel boiler doing repair work. Air was being
on july 24, 1990, employee #1, of vulcan iron works inc., was part of a crew installing chandelier brackets on structural steel col
an employee of an electrical contractor was working from a fiberglass ladder, installing the wiring for a chandelier. The circuit on
on june 21, 1990, six employees of argersinger morse construction co. were cleaning up and removing equipment and materia
on august 7, 1990, a paint crew of four workers unloaded a truck and placed 30 five gallon buckets of paint on the platform on t
on september 2, 1990, employee #1, age 33, and the grading foreman of holloway construction company were working late rep
an employee was part of a three-person crew that was finishing the framing of a ranch-style home. The employee was working
a boom operator was unloading a caterpillar backhoe from a lowboy trailer. Four other people were standing on the ground, wa


                                                      Page 89
                                                        all


a three-person crew had just finished painting a house. The employees began picking up their tools and equipment. Two of the
an employee was splicing a broken 7200-volt power line. The recloser for the line had malfunctioned and allowed the line to rem
on february 2, 1990, employee #1 was riding on a tractor that was struck by an automobile. This accident is being reviewed by t
employee 1 was replacing old cable tv line employee 2 threw a roller up to employee 1 employee 1 caught the roller, employee
at approximately 12:35 p.m. on august 9, 1991, employee #1 was operating an mr 25 strato-lift. A coworker returned from lunch
at approximately 11:30 a.m. on july 25, 1994, employee #1 was moving bundles of cedar boards with a cat v80e forklift at carw
on june 3, 1999 at approximately 4:15 p.m., mr. boyd was cement finishing when it appeared he suffered a heart attack and die
at approximately 3:30 p.m. on july 13, 1992, employee #1 was closing a water valve on a hydrant. He suffered a possible heart
employees #1 and #2 were working on a gym roof during a demolition operation. A portion of the structure collapsed and both e
employees #1 and #2 were working on a gym roof during a demolition operation. A portion of the structure collapsed and both e
employee #1 was on his way to a work site when a car pulled in front of him, resulting in a collision. Employee #1 was killed.
employee #1 was approximately 45 ft high in a manlift while wiring a street light. The manlift was a maintenance platform manu
two employees in a car pulled out of a driveway onto a highway and got hit by a pick-up.
two employees in a car pulled out of a driveway onto a highway and got hit by a pick-up.
at approximately 10:30 a.m. on september 10, 1990, employee #1 was walking out of the metro sewer tunnel and was struck a
on 08-17-96 at 7:03 am the employee donald casper removing one of the metal sheetings on the roof edge to uncover the insta
workers were extending a crane boom. Employee #1, the operator, was under the live boom, which was suspended 4 ft above
at 2:00 p.m. on july 16, 1992, employee #1 was bleeding air from a piped pressurized grease system. He was loosening and re
at about 2:20 p.m. on november 23, 1990, employee #1, vice president of bosler energy systems, inc., was finishing the installa
at approximately 8:00 p.m. on august 17, 1994, employees #1 and #2 were being elevated approximately 220 feet in a personn
at approximately 8:00 p.m. on august 17, 1994, employees #1 and #2 were being elevated approximately 220 feet in a personn
on august 13, 1992, employee #1 was instructed to cut rafter tails on the wood frame roof of a barn under construction. While c
employee #1, who was driving a drum roller as his part in underground utility work and asphalt restoration, had finished his wor
the employee was doing his normal duties as a garage door installer, he was installing garage doors at the edmond's location. T
employee fell from the 3rd floor of apartment building which was under construction. Employee was on a deck which had one g
At 6:00 p.m., on 01/11/2000, the operator of a Case 590 SL backhoe was preparing to begin an excavation at a small hole. The
At 6:00 p.m., on 01/11/2000, the operator of a Case 590 SL backhoe was preparing to begin an excavation at a small hole. The
Deceases was in the normal course of employment was walking across the job site. Staggered and fell face down. Co-workers
employee #1 was laying pipe in an 8 ft trench. The side of the trench, which was approximately 4 ft long, caved in and buried th
at approximately 12:00 noon on march 4, 1995, employee #1 suffered a heart attack and died.
on 7-28-94 at about 8:30 am, the employer (#1) and two workers arrived at 6406 181st ave. Ct. E., bonney lake, was to set-up
employee #1, the company owner, was working on the roof of a house that was under construction. He carried two buckets to t
employee #1 and coworker were assigned the task of securing the roofing material atop roof trusses. The two workers tied off u
employee #1 had been welding in a confined space during the day shift and died the next day in the early morning. The coroner
one of the partners for whitecap construction was operating a bobcat with the backhoe attachment, excavating in a existing, co
at about 3:30 p.m. on november 18, 1993, employee #1 suffered a heart attack and died.
employee #1 was shoveling debris that was left behind after jersey barriers were removed from inside a coned-off lane on highw
an employee was replacing a motorola ballast (model no. M2-rn-t81ll277) in a 277-volt lighting fixture on the mezzanine level of
on 5/3/98 at 2:05pm employee #1 was operating a jlg (boom lift) industrial truck, stocking insulation to a higher level in preparat
on 5/3/98 at 2:05pm employee #1 was operating a jlg (boom lift) industrial truck, stocking insulation to a higher level in preparat
on 08/21/95 at 0815 employees #1 and #2 were pouring cement sidewalk approx. 17 to 20 ft west of s.r#503, bursh prairie and
on 08/21/95 at 0815 employees #1 and #2 were pouring cement sidewalk approx. 17 to 20 ft west of s.r#503, bursh prairie and
on 12/07/96 at 9:00 am this employee was attaching slings to 60 foot sections of metal pipe to be hoisted by a crane in order to
worker was descending stairs, temperature was below freezing, stairs had been cleared of ice and snow approximately 1 hour
owner and employee observed at the starhouse lounge at 5pm. At 7pm both were fatally injured when the pick-up driven by the
owner and employee observed at the starhouse lounge at 5pm. At 7pm both were fatally injured when the pick-up driven by the
on 06/30/9, at approximately 11:00am, employee #1 was operating a 55,000 gw concrete pumping truck when he lost control o
on 12-22-99, at 10:50 am, employee #1 was performing his regular duties as a roofer along with a crew of 5 to 7 workers. while
tractor rolled over 3 or 4 times onto victim.
on 6-13-97 at approximately 11:00 am employee #1 was operating a 3 ton bomag compactor roller, compacting a new gravel s
employee #1 had complained of chest pains to a friend during the afternoon break. After drinking a pepsi, he went back to work
framing contractor was framing a condo building. 4 workers were attempting to install an overhead structural beam. when lifting


                                                     Page 90
                                                          all


on june 11, 1990, a 1988 model 480e backhoe was unloaded in a ferry parking area in order to be driven onto the ferry. The op
employee #1 was getting into a pickup truck at a job site and suffered a fatal heart attack. Attempts to revive him were unsucce
on january 19,1991 at about 4:15pm three employees of refinery and four employees of a subcontractor were pulling a blind ou
on january 19,1991 at about 4:15pm three employees of refinery and four employees of a subcontractor were pulling a blind ou
on january 19,1991 at about 4:15pm three employees of refinery and four employees of a subcontractor were pulling a blind ou
on january 19,1991 at about 4:15pm three employees of refinery and four employees of a subcontractor were pulling a blind ou
on january 19,1991 at about 4:15pm three employees of refinery and four employees of a subcontractor were pulling a blind ou
on january 19,1991 at about 4:15pm three employees of refinery and four employees of a subcontractor were pulling a blind ou
on january 19,1991 at about 4:15pm three employees of refinery and four employees of a subcontractor were pulling a blind ou
employee #1 was at his work station at 7:00 a.m. within an hour he collapsed after suffering a heart attack and was airlifted to a
at approximately 11:30 p.m., employees under the direction of a department of transportation inspector were setting up traffic c
at approximately 11:30 p.m., employees under the direction of a department of transportation inspector were setting up traffic c
on january 29,1990 at approximately 12;45pm employee #1 was climbing up to the cabin of the hammer had tower crane that h
line #10 listed 05- massive internal injuries on febuary 2, 1990 employee #1 was going to relieve the flagger at 12:00 am (noon)
two employees were installing sheet metal on a roof. A 7200-volt overhead power line was located 8 feet above the roof. The sh
two employees were installing sheet metal on a roof. A 7200-volt overhead power line was located 8 feet above the roof. The sh
on april 10,1990 at approximately 9;30am employee #1 and a co worker were cleaning and patching new storm drain catch bas
a power line worker was working too close to electric equipment energized at 7600 volts. He was warned about this several tim
walked behind load asphalt truck as it was backing up and was crushed.
at approximately 11:45 a.m. on august 30, 1990, employee #1 was operating a combine on a steep hillside. The combine overt
at approximately 2:05 p.m. on november 10, 1993, employee #1 was attempting to adjust the brakes on a lowboy trailer. The op
on 06/02/91 at app. 11a.m. employee #1 was painting the outside wall of single-family dwelling at 672 kitsap lake road n.w. in b
at approximately 11:30 a.m. on july 6, 1990, employee #1 was refueling an insulation blower that was mounted in the back of an
on may 22, 1990, employee #1 was working 18 ft high undoing she bolts on a concrete form. When he went to move, he found
An employee was driving uphill on Pearl Hill Road by Chief Joseph Dam and lost control of he truck he was driving. He went ov
at approximately 11:20 a.m. on july 22, employee #1, an apprentice carpenter employed by david a. mowat co., fell approximate
at approximately 11:00 a.m. on june 4, 1996 employee #1 was fatally injured when the building she was working at collapsed. H
on 09/25/96 employee #1 was fatally injured when he was backed over by a dump truck loaded with concrete.
on 08/15/97 at approximately 11:00 am employee #1 fell through a hole in a metal roof that was being repaired. He fell approxim
an electrician went into an electrical room to ground some conductors for the purpose of marking phase orientation. The condu
Two employees were working in the 500 Block of Woodward Street, Wenatchee, Washington. They were run over by a Chipma
on the morning of november 22, 1994, employee #1, who was an equipment operator/laborer, a foreman/operator, and two traf
employee was placing concrete with a concrete bucket suspended from a ton crawler crane. Employee pushed suspended buc
employee was working approximately 30 feet on a new wooden utility pole. pole did not have energized lines nor was the emplo
This Establishment Was Hired As A General Contractor To Demolish An Office Structure On A Mezzanine Built On Steel Deck
an emplloyee was working on his own on sunday and was moving some steel beams with a boom crane. The steel beam hit an
on 7/27/96, employee #1 fell from the ladder he was descending when an anchor bolt pulled out of the wall to which the ladder
deceased was making natural gas connections when he fell from the elevated work platform to the concrete floor 16-feet below
employee #1 was building a steel wall with steel plates supported by a 50 ton overhead crane and attached to a sling with a job
the victim was operating a truck mounted well drill at the base of an earth levee when a 36" diameter casing 25" long being plac
employees were installing skylights on a roof that was approximately 22 feet high when employee #1 fell through skylight #24. H
employee #1 was in a trench approximately 10 to 11 feet deep and 20 inches wide. The trench was not shored or sloped. He w
employee #1 was cutting the rooftop from a 58 foot high grain bin. He failed to cut all of the struts, causing the cuttings to fall at
employee #1 was removing the cover from a floor opening so that a cart could be moved through, when he stepped into the op
employee #1 was backed over by a city trash truck while at the dump. He was killed, suffering head injuries.
employee #1 was killed when his head and arm were crushed against the frame of a bobcat.
at approximately 7:05 a.m. on august 17, employee #1 arrived at a worksite located between mile markers 341 and 345 of i-70
at approximately 9:35 a.m. on september 20, 1994, employee #1 was walking east on the shoulder of interstate 70 west toward
at approximately 11:00 a.m. on november 21, 1994, employee #1 was working with a crew of five other employees performing
a truck driver was carrying a chain sling. The sling touched the outriggers of a truck crane as the boom contacted an overhead
employee #1 had just entered a trench that was 14 ft deep by 36 in. wide by 35 ft long to lay out a 6 in. drain pipe when the nort
a truck driver was standing on the rear of a conveyor-type boom truck. The truck was a freightliner fl80 (vin 1fvxjlbb1r1568592)


                                                      Page 91
                                                         all


employee #1 was painting a 300 ft radio tower using a fall restraint system consisting of a chain connected at both sides of his
a power line worker and an apprentice were connecting a tap from an overhead power line to a terminal for an underground po
a communications worker was working from the bucket of an aerial lift, repairing a telephone cable supported by a utility pole. T
employer was operating a 42 foot line truck from the basket. When the upper boom passed the 0 degree on the lower boom, th
an employee used a scissors lift (500 pound rated capacity) to lower a transformer (1820 pounds) after the suspension wires w
the deceased was climbing a ladder when he had a seizure and fell about 12 feet to the pavement of the parking lot.
on july 16, 1996 at approximately 8:30 a.m. this demolition company was removing a brick smokestack over 100' high, at an un
employee fell through a hole he had just created on the 2nd floor. Employee fell 10 feet 3 inches to 1st floor landing on his head
employee exiting roof at end of workshift via extension ladder set against parapet. To access ladder employee had to climb from
employees #1 and #2, subcontractors, were assigned to install an orifice flange on a 1 1/2 in. fuel oil return line that extended fr
employees #1 and #2, subcontractors, were assigned to install an orifice flange on a 1 1/2 in. fuel oil return line that extended fr
an employee of an electric utility was working from a wood extension ladder, using a torch to cut away a spring-loaded pipe han
employee #1, a truck driver, positioned himself between the tailgate and the dump body to clean asphalt material from the tailga
employee #1 placed a 10 foot fiberglass stepladder, in the closed position, against the side of the sda tank. The ladder was pla
employee #1 and a coworker were raising a 16 ft by 10 ft shelter that was set 10 ft high on ten 6 in. by 6 in. posts and supported
at approximately 10:30 a.m. on may 13, 1994, employee #1 stepped outside the shoring to locate a lateral and both sides of a v
an employee was working in the attic of a bank. He contacted an ungrounded conduit running to an exterior lighting fixture. A g
employee #1 was standing on the roof of an underground concrete building directing a loaded dump truck onto the roof. The ro
an employee was moving an aluminum ladder near a house on which some roofing work was to be completed. The ladder cont
on or about may 24, 1994, employee #1 and a friend were standing 28 ft high on homemade scaffold planks on a pump jack sc
employee #1 suffered fatal crushing injuries while attempting to stop a runaway, unattended side boom pipelayer. Employee #1
employee #1 suffered a fatal crushing injury after he fell from tipped-over side boom pipelayer equipment. Employee #1 was op
on september 27,1991 an employee died of thallium poisoning. The employee, and electrician had been doing work in a college
on november 21, 1991, a ray co. Little rascal roller, model 400a, was delivered to a paved intersection. Employee #1 volunteere
employee #1 was walking on a roof when a portion of it gave way. The employee fell approximately 45 feet to a concrete floor a
employee was working on an electric water heater which was leaking and energized. Employee apparently moved a pipe fitting
at 5:30 p.m., a tractor trailer laden with brick ran into a pickup truck that was driving behind a convoy of road construction equip
at 5:30 p.m., a tractor trailer laden with brick ran into a pickup truck that was driving behind a convoy of road construction equip
an employee was using a 240-volt floor sander to sand a hardwood floor. He was wearing shorts and sweating because of the h
employee #1 was operating a bulldozer on or near a sloped embankment. The bulldozer, which was not provided with a roll-ove
at or about 11:00 a.m. on april 26, 1995, employee #1, a masonry/general contractor, went to the chestnut hill township recyclin
three employees had assembled a 30-foot-long piece of aluminum rain gutter. To place the gutter into position, one of the emp
three employees had assembled a 30-foot-long piece of aluminum rain gutter. To place the gutter into position, one of the emp
the employee was dismantling a scaffold. He was walking on the planked surface approximately thirty eight feet above ground l
the employee had been working with a subcontractor cutting and enlarging an opening in a concrete floor. After the job was com
employee #1 fell 10 ft through an unguarded ground floor stair opening to the concrete pavement. He died.
on june 26, 1991, employee #1, a painter, was overcome by carbon monoxide while using a gas-powered airless paint sprayer
170354492
at approximately 11:10 on february 1, 1994, employees #1 and #2 were at a sewage treatment plant installing two large butterfl
at approximately 11:10 on february 1, 1994, employees #1 and #2 were at a sewage treatment plant installing two large butterfl
employee #1, a roofer/loading foreman, was unloading roof tiles from a pallet and placing them on a second story roof. He fell f
a laborer performing asbestos removal work was pulling a deenergized electric cable from some conduit. He opened the rear p
on or about september 23, 1994, in the afternoon, sometime after 1600 hours, employee #1 was in the process of making four
while working, in bldg. 35, on a trane centrovac water chiller, which contains 1800 lbs. Of freon-11, mr neal found a leak in the e
at approximately 2:35 p.m. on october 26, 1994, employee #1 was directing two forklifts that were lifting a 2.01 ton can oven in
at about 9:41 a.m. on october 28, 1993, employee #1, a journeyman lineman, fell about 36 feet from a utility pole to a concrete
lowe north construction inc (sic 1799) on 5/20/96, at 2:00 p.m., employee #1 was fatally injured when he fell from a cantilevered
see attached report
an apprentice electrician was replacing ballasts and florescent lighting tubes. He was instructed by his foreman to turn off half o
"this citation amends citation no. 1 item no. 2 issued on 12/07/96 to waive the penalty. All other items of the citation and penalty
ductile iron pipes wrapped in heavy duty plastic material about 18 feet long, 20 inches in diameter and weighed 1500 pounds ea
at about 5:00 p.m. on january 18, 1995, employee #1, of all access excavating, was working alone in the basement of a hillside


                                                      Page 92
                                                         all


o c jones and sons (sic 1611) mr toedtemeier was marking grade level. An heavy equipment grader was operating inthe same
On 8/13/99 at about 8:30 a.m. I responded to a fatal accident. The deceased date of birth 4/11/60 was working as a locator for
Employee was a welder and a close family friend of the employer and owner of mejia steel welding, inc. the company had alrea
on 9/25/98, the president of tsa fire protection, inc. was making observations at the jobsite located at 388 townsend st., sf. Late
employee, signal man/ironworker, stepped from the roof parapet to ledger of unplanked scaffold to check load. On return from
at approximately 1:15 p.m. on december 12, 1994, employee #1, of gte telephone operations, was climbing on a ladder that slid
On 9-13-95 at approximately 1120 at the intersection of W. Main St., and International Blvd., in the city of Calipatria, CA. a trenc
On 9-13-95 at approximately 1120 at the intersection of W. Main St., and International Blvd., in the city of Calipatria, CA. a trenc
On 9-13-95 at approximately 1120 at the intersection of W. Main St., and International Blvd., in the city of Calipatria, CA. a trenc
at approximately 7:40 a.m. on july 15, 1991, employee #1 was instructing another employee on the operation of a ferguson she
a foreman on a four-person painting crew was painting a 160-foot-tall transmission tower. He was not using any fall protection e
victim was in back of a truck, he unhooked two straps which secured the load. As he turned to face out of the truck, the back of
employee #1 was operating a daewoo excavator with a ram concrete breaker attachment which was in use in an 11 feet 6 inch
employee #1 was operating a daewoo excavator with a ram concrete breaker attachment which was in use in an 11 feet 6 inch
on 2/20/97 the victim was assisting other crew members dropping wood planks into a box- plank bounced hitting the victim in th
employee was standing on the frame of a ramsey asphalt rap conveyor 22 " above ground level. Employee is using a ballpen h
the victim was installing a 21 feet long light pole onto a 2 feet high concrete base. A 72 kv power line was located 6 feet directly
the victim was a steel worker who, with two other crew members, was installing insulation and steel roof deck sheets. The build
two workers were using a forty feet, aluminum, extension ladder extending sufficiently to access the 21 feet high roof level of a
two workers were using a forty feet, aluminum, extension ladder extending sufficiently to access the 21 feet high roof level of a
victim entered new residential basement to light an lp gas temporary heater. Hose from cylinder had been threaded down to ba
a power line worker had climbed out of an aerial lift bucket, which was elevated about 60 feet above the ground, onto a steel ut
victim was working on a project where a two-story house had been jacked up and supported by cribs in order to replace the bas
the victim was in a manhole excavation where a concrete manhole was being installed. It was his job to line up and land a conc
at approximately 1:30 p.m. on december 15, 1992, employee #1 had walked out onto state road 23 to stop traffic to allow a dum
at approximately 1:30 p.m. on december 15, 1992, employee #1 had walked out onto state road 23 to stop traffic to allow a dum
employee #1 tried to climb onto a 40-ton caterpillar articulating dump truck using the equipment ladder located between the truc
employee #1 was operating a case uniloader - he obtained a bucket load of dirt and then dumped part of load off the edge of dr
employee #1 was struck in the head by an aero 60, sky king arial lift, he and another employee were preparing the lift to taken t
on march 31,1997 company was on site demolishing a 6 story building. The accident occurred when employee #1 and a fellow
employee #1 was riding in a pickup truck when he collapsed. Cpr was administered and he was transported to a hospital. He di
a crane operator was using a crane to move equipment off of a flatbed truck and swing it around for two employees to unhook.
a crane operator was using a crane to move equipment off of a flatbed truck and swing it around for two employees to unhook.
at approximately 2:36 p.m. on july 14, 1993, a very strong thunderstorm passed over a private residence under construction. Th
at approximately 2:36 p.m. on july 14, 1993, a very strong thunderstorm passed over a private residence under construction. Th
on 10-8-98 at approx. 11:45am employee #1 climbed to top of ladder on ford f700 truck, placed a chain saw into bottom of artic
the victim working with a crew of 6 was in the process of placing a 6'x 25' section of insulation at the leading edge of a roof. The
the victim was holding onto the load line of a crane to guide it to where he would connect it to a pile driving hammer. The crane
on june 10,1998 at approximately 12:30pm employee #1 and another set crew employee were raising the front door section of
victim #1 was mowing roadside for dept of transportation when mowing on a slope and failed to see concrete culvert front of tra
a experienced crew leader for an electrical contractor approached a section of a 12-kv, 600-ampere switchgear. The host elect
on or about 5-5-97 at approximately 10:57am victim was working on the north side of a ditch that was being cleared of trees. A
on 7/24/97 at approx 2:00pm operator employee #1 and groundman employee #2 were removing an approx 500 lb existing sign
on 7/24/97 at approx 2:00pm operator employee #1 and groundman employee #2 were removing an approx 500 lb existing sign
on 12/15/97 at appprox 10:15 am employee #1 and another ironworker employee were positioning an approx. 22' long crane ra
while attempting to lift and position a 6" x 12" (18'10" long) wood beam in basement the victim fell backward off the (24 inch hig
an apprentice electrician was standing on an elevated work platform (moon buggy), assisting in the replacement of electrical co
on 9-3-96 approx 5-10 minutes prior to 7:15am employee #1 and two other employees arrived at the the fuel pumps, outside th
an employee was stringing a 0.25-inch steel support strand for a cable television line. To string the support strand between two
an employee was assigned to install lighting fixtures in a ceiling. The new fixtures were to replace temporary lighting. His super
at approximately 10:00 a.m. on december 6, 1981, employee #1 was installing a piece of gable rake trim. He was working on a
three employees were assigned to grind, chip, and patch excess concrete from exposed form seams in the south stairway of bu


                                                      Page 93
                                                          all


employee #1 was working off a metal bracket form scaffold, approximately 12 1/2 feet above the base level of an elevator shaft
employee #1 and a coworker were assigned to install four skylights on a flat built-up roof. Another contractor had removed the e
employee #1 placed a ladder on a lower level roof that extended to an upper level roof to install siding on a residential home. Th
employees #1 and #2 went on a newly installed rubber roof approximately 20 ft from ground level to check the roof and bring do
employees #1 and #2 went on a newly installed rubber roof approximately 20 ft from ground level to check the roof and bring do
employee #1, a tractor-trailer driver, was delivering two 16,000 lb pieces of precast concrete. One piece was removed while the
a crew was dismantling a 60 ft silo. Employee #1, a 17-year-old, climbed a ladder in a chute attached to the side of the silo. The
two electricians were changing ballasts in overhead fluorescent lighting fixtures. The foreman opened the switch to the lights in
employees #1, #2, and #3 were in a dry well modifying sewer mains. Fluids left in the pipe for three months flowed into the work
employees #1, #2, and #3 were in a dry well modifying sewer mains. Fluids left in the pipe for three months flowed into the work
employees #1, #2, and #3 were in a dry well modifying sewer mains. Fluids left in the pipe for three months flowed into the work
employee #1, a tapper, fell from a 5 ft high, less than 45 in. wide scaffold platform that was not equipped with standard guardra
the deceased was assigned to, with an oxygen-propane torch, cut up a sump from a flammable liquid storage tank for scrap. Th
on december 28, 1995 at approximately 8:30am employee #1 exited operator's cab of dozer stood on track. The dozer moved
employee # 1 climbed atop the stock in an attempt to locate an item(s). He fell onto the concrete floor, and was killed.
at approximately 4:40 a.m. on october 12, 1995, employee #1 was opening a closed traffic lane. A driver was entering the highw
two men were installing insulation and metal roof panels on metal roof joists. The roof hs a 2 in 12 slope and is 17'8" at the eve
Owner/operator apparently was struck by and crushed in-between backhoe bucket and outrigger after he got off and left motor
employee #1 was loading a cat d-6 bulldozer onto a trailer via ramps built into the trailer. The trailer was at a pitch of about 5 de
at approximately 8:30 a.m. on may 10, 1995, employee #1 was preparing to perform some troubleshooting from the car top of e
while acting as a flagger on a highway construction project, employee #1 was struck and killed by an oncoming vehicle that faile
freight elevator in an 11 story hotel had no landing call buttons to summon the elevator to a particular floor. The most common
the employee was a lineman with a local telephone service provider. He had climbed a telephone pole to remove a telephone c
employee #1 was cutting a trench for a sewer line through what the company classified as solid rock. The rock had fissures and
three employees (a journeyman electrician and two apprentice electricians) of an electrical contractor were working in a mecha
employee #1 was found in a passageway after leaving the break area to return to work. He was transported to rowan memorial
at approximately 8:30 a.m. on june 11, 1993, employee #1 was attempting to climb a ladder to the roof of a building 27 ft from g
a speeding car entered a coned-off and identified work zone at the overhead bridge at i-85 and randleman road, striking two em
an employee was moving a werner, 12.2-meter-long, aluminum extension ladder from a van storage rack. (The ladder was new
employee #1 and coworkers, of lenco silo systems, inc. were removing roof forms from the inside of a 68 foot silo they had con
employee #1 was involved in a welding operation at the hds unit at the flying j oil refinery. Diesel fuel flowing at approximately 2
at 8:20 a.m. on september 1, 1993, at the south jordan middle school construction site, employee #1 was working in a trench w
employee #1 was welding braces for the roof of a facility under construction; the task required dragging the welding cable as he
an employee of a construction firm was working in the conveyor pit of a truck hopper. His supervisor had assigned him the task
employee #1 was filling a water truck at a fire hydrant and climbed on top to check the water level. Although the top of the tank
employee #1 was laying carpet in an elevator with the elevator doors propped open when the elevator car unexpectedly droppe
an electrical contractor was remodeling the electrical service to a state office building. The contractor's employees were moving
a truck driver and his assistant arrived at a site and parked their log truck and trailer loaded with 30 ft logs. Because it was late,
at about 5:30 p.m. on august 11, 1993, employee #1, of concrete masters, inc., who was involved with curb and sidewalk maso
on june 9, 1998 at 11:50 am the accident victim enetred a sewer manhole that contained an oxygen deficient atmosphere.
on march 23, 1998, victim was buried in collapse of excavation wall. Employee was to "shoot grades" from top. However, two e
victim in trench - backhoe hit overhead powerline - arced into trench.
at 8:45 a.m. on may 25, 1994, employee #1 was working on highway 35w in the northbound lane as part of a work crew that wa
at the end of a work shift, an employee was told to move a condor aerial lift to the back of a building so that the aerial lift could b
on july 27, 1996, an ironworker who was welding inside a water tower, fell from an unknown height. The victim was last seen 5
employee operating a cat 966 front end loader, stopped on an inclined gravel road, unit began to roll backwards into a road ditc
at approximately 6:15 p.m. on july 7, 1995, employee #1, the operator of a nine-wheel rubber tire compactor, apparently lost co
two brick masons were moving a six-frame-high mobile scaffold around a corner of a school building. One of the employees lift
two brick masons were moving a six-frame-high mobile scaffold around a corner of a school building. One of the employees lift
on october 15, 1996, at approximately 1515 hours, three employees repairing a water pipe in a 10 ft deep excavation were invo
on thursday, october 31, 1996 at approximately 7:20 am, an employee was killed when he was knocked down and run over by
on december 9, 1996, a crane oiler was working from a side platform of a line-belt crane. The oiler opened the outer sliding doo


                                                       Page 94
                                                          all


employee #1 was connecting a joist to a column 39 ft above the ground. He walked on the 9 1/2 in. beam a distance of 25 ft to
employee #1 was going to lunch. He was driving a john deere model 440 d log skidder he had operated flat rm. He was involve
a forklift operator was using a lull all-terrain high-lift loader to lift employees #1 and #2 and six metal roofing sheets approximate
a forklift operator was using a lull all-terrain high-lift loader to lift employees #1 and #2 and six metal roofing sheets approximate
employee #1 was driving a caterpillar 627 scraper on a gravel road to another work site 40 miles away. He lost control of the sc
an electrician was replacing electrical components in a municipal light plant. He either slipped or fell into energized busbars and
employee #1 was flagging for a hot seal kettleman in a construction zone on an interstate highway. A driver of a pickup truck br
at approximately 7:00 a.m. on june 22, 1994, employee #1 went to the ziegler industries work trailer located on the premises of
on september 9, 1997 at approximately 7:30 a.m., employee #1 and employee #2 (brothers) were moving wire mesh mats to an
on september 9, 1997 at approximately 7:30 a.m., employee #1 and employee #2 (brothers) were moving wire mesh mats to an
at approximately 11:25 a.m. on august 5, 1994, employee #1 was working on a case backhoe and was positioned between the
at approximately 8:30 a.m. on october 12, 1994, employee #1 was installing a road sign on the west shoulder of county road x-1
a power line worker climbed a utility pole to pull a cutout door. He was wearing only leather gloves. The employee contacted the
employee #1 and two coworkers were attempting to retrieve a truck from over a hill using a side boom pipe handler. The truck w
employee #1, a state certified blaster with 16 years experience, was working alone blasting in an open field to loosen limestone
a plumber was clearing a clogged sewer line. Instead of cleaning the line from outside of the house, the employee decided to w
employee #1 was welding a chute on a bark load-out tower, moving from one side of the hopper to the other side. He bent dow
employee #1 was walking from the base of stono bridge to the bridge house located in the middle of the bridge. He had to walk
on or about january 16, 1995, employee #1 fell off a stool approximately 1 to 1 1/2 feet high when he suffered an epileptic seizu
employee #1 was repositioning choker sling on a 65 foot long metal roof truss standing upright on the ground (on base) to be lif
a painter was assigned to paint a fire deluge system that was 7.3 meters above the ground. He was working from a ladder and
On March 27, 2001, at approximately 3:55 pm employee #1 and 2 were instructed to obtain tools from a storage trailer. Employ
a steel worker was removing a piece of sheet metal from a wall approx. 3 feet in length in preparation for laying metal decking o
employees had just completed roofing a residential house and were packing their tools and equipment on the company truck w
employees had just completed roofing a residential house and were packing their tools and equipment on the company truck w
employees had just completed roofing a residential house and were packing their tools and equipment on the company truck w
employees had just completed roofing a residential house and were packing their tools and equipment on the company truck w
employees had just completed roofing a residential house and were packing their tools and equipment on the company truck w
employee #1 was performing his normal job duties of operating a road patcher, when he was struck by a vehicle and died at sc
test
employee was up approx 8' high on an extension ladder to guide a metal fabricated support "windbrace" into place. As he reach
employee was compacting soil on a roller compactor leading up on a roadway leading to a new bridge. She got too close to the
Two employees were clearing trees, brush, and beaver dams along a creek. One employee cut a 65 foot high double branch tre
employee number one was working on third floor as a carpenter on a building under construction. For unknown reasons, he lea
employee #1 was working in a residential house attic installing new air conditioning equipment. He contacted an electrically ene
employee #1 was working cutting wood on the ground. Employee #2 was standing on a 2" 44' lateral temporary brace holding th
employee #1 was working cutting wood on the ground. Employee #2 was standing on a 2" 44' lateral temporary brace holding th
employee #1 was operating a portable table saw (mikita) that was being used to cut frp strips with a piece of plywood as a mat
employee, first day on the job, was working on the roof of the new construction. He was trying to pull a generator onto the palle
on march 23, 1998, at approximately 11am, employees #1,2,3 and 4 were in the process of repairing damaged portions of a wa
employee #1 was in charge of a 5 man labor crew that was to install a "sweep" on the end of an electrical conduit being installe
two employees were working at a 10 story condominium building and they were working from a two-point suspended scaffold. A
two employees were working at a 10 story condominium building and they were working from a two-point suspended scaffold. A
after lunch on 11/30/98 an employee (victim) decided to go to the trailer to retrieve some supplies for his afternoon work. He wa
a four-person electrical crew was working in a restricted access electrical control center at a paper mill. The crew was removing
at approximately 2:15 p.m. on january 12, 1996, employee #1 was directing a dump truck to a spot where it could unload. He w
employee #1 was operating a self-propelled pneumatic roller, compacting clay gravel on the shoulders of a highway that had be
struck by a suspended load
the victim was welding on steel rebar inside a 8" to 9" hole(punch out) while repairing sections of the right lane of interstate 20 n
employee #1 was working on a tin roof when he stepped onto a corrugated fiberglass skylight and fell approximately 25 feet to
after employee #1 had welded three joists, he walked along the i-beam pulling welding leads. Employee #1 became entangled
an employee was terminating cables in a switchgear enclosure that had not been deenergized. He apparently contacted an ene


                                                      Page 95
                                                         all


on august 12, 1994, employee #2 was working in a trench that was approximately 12 ft deep, 36 in. wide, and over 20 ft long, w
on august 12, 1994, employee #2 was working in a trench that was approximately 12 ft deep, 36 in. wide, and over 20 ft long, w
employee #1, a foreman, was standing at the edge of a wharf using a hand brush to paint the stern of a ship when he slipped a
at approximately 2:00 p.m. on may 11, 1995, employee #1 was directing a bulldozer operator on where to push down a large pi
see osha 170 supplement. [erg note: no report supplement attached.]
at approximately 11:00 a.m. on august 28, 1995, employee #1 and a coworker were attempting to lower a modular trailer to a s
two employees were shooting grades on a bridge being constructed over a river. Employee #1 walked out onto a horizontal ste
a contractor for an electric utility was installing a new phase conductor to an existing overhead power line. A power line worker
a 35-year-old electrician was standing on a 1.8-meter (6-foot) fiberglass insulated ladder, working on a 277-volt florescent lighti
employee #1 and five coworkers were assigned to re-roof a newly constructed gymnasium. They began their early morning dut
at the marriott marquis, employee 1 and 2 were standing directly in front of the elevator (#11) on the 30th floor waiting for emplo
ee # 1 was operating a dump truck hauling gravel to the job site which is a road widening project. Ee # 1 was instructed by his f
thursday, may 30, 1996, a latex employee was killed while laying pipe. Boom operator 1 was positioned 22' away from the begin
on august 4, 1994, employee #1, a laborer, was helping to lay water lines. At the end of the day he became disoriented and los
at approximately 12:30 p.m. on august 26, 1994, employee #1 was found lying face down in approximately 1 to 1 1/2 ft of water
employee #1 was gathering material and transferring it to another floor when he fell eleven stories to the ground. He died.
two employees were stomping down dirt in a excavation that measured 17 feet wide by 26 feet long by 5 feet deep. While the o
at approximately 12:45 p.m. on june 15, 1995, employee #1 was building a work platform on the 15th floor of an elevator shaft s
employee #1 was a member of a crew removing roof surface material from a large warehouse structure. The material consisted
#1 was working in an aerial bucket mounted on a truck. The unit is a pitman aerial device-model hs - 42 -hab frame. He was wo
at approximately 8:30 a.m. on august 23, 1993, a dump truck driver drove the front wheels of his vehicle over the back of emplo
at approximately 8:30 a.m. on june 15, 1993, employee #1 and several other employees were involved in a special overtime as
employee #1 entered an 11 ft 8 in. trench to place a surveyor's rod at the bottom. The walls collapsed, crushing him to death. T
employee working in trench 5'7" deep when walls collapsed, crushing employee to death. The trench caved in because employ
at about 7:48 a.m. on may 9, 1994, employee #1 was placing a 2 in. by 6 in. by 12 ft wood joist into metal joist hangers. While w
employee #1 was working alone on a roof while coworkers were working on another roof of a multi-building shopping center. Em
at or about 3:00 p.m. on october 22, 1993, employee #1 was standing in the rear of his 18 wheel peterbilt dump truck that was b
an electrician, who had over 17 years of experience, was working on an electrical control. He was replacing a photo-electric cel
at approximately 8:30 a.m. on october 1, 1993, employee #1 was assigned to help a grader operator backfill an area next to a n
employee #1 was illegally dumping approximately 4 tons of roofing material onto a vacant lot. The power take-off that raised an
at approximately 3:24 p.m. on february 23, 1994, employee #1, of mahaffey drilling, was supervising the drilling of caisson hole
on may 9,1994 at approximately 10:10 a.m., employee #1 was standing and working at removing chain binders that were restra
at approximately 12:30 p.m. on august 16, 1994, employee #1, a tree trimmer, was nearing the completion of his lunch break. T
on friday 2-24-95, at approximately 0945 hrs., employee #1 was per- forming duties of removing roofing materials from a buildin
on april 12, 1993, employee #1, an iron worker decker/foreman, was spreading decking with a coworker who was welding the 3
at about 3:00 p.m. on june 9, 1993, employee #1, a 56-year-old truck driver, was standing on the side of an excavation when it
two employees were retrieving welding lead left on a 45' high catwalk located inside the south side of bldg #301, site 3, a.f. plan
at approximately 8:30 a.m. on july 19, 1994, employee #1 was operating a compactor to compact dirt off a roadway. An oncomi
a father, his son, and his nephew were constructing a vacation log cabin. The father was operating a large stinger crane mount
a father, his son, and his nephew were constructing a vacation log cabin. The father was operating a large stinger crane mount
on august 3, 1994, at north highland, ca, employee #1, a 79-year-old company owner, was working with several employees to d
at 12:38 p.m. on february 21, 1996, employee #1, of the yuba county public works department, was one of two flagmen controll
on march 30, 1998 at approximately 12:00 p.m., employee #1, of best masonry, was working adjacent to a 6' high brick wall tha
an employee was preparing to start a welding job. He was positioning the welder and setting it up for the job. He sat down on a
employee #1 and coworkers were working about 38 ft above a concrete floor on a metal roof of a building. They were applying
on 04/24/98 at approximately 0900 hrs, the victim working as a laborer at a project putting a steel deck roof on a large tilt up str
on 04/24/98 at approximately 0900hrs the victim working as a laborer at a project putting a steel deck roof on a large tilt-up stru
sic 1623: the employer was installing a 5,500 foot long underground oil pipeline. At the time of the accident, the crew was in the
on april 12, 1996, company yard/scaffolding material staging area, the yard supervisor, employee number 1, was loading scaffo
co. Name:j. W. chaffey construction.sic code: 1522 victim fell from moving pick-up truck while supporting cabinet work. Truck w
on october 13, 1994, employee #1, a carpenter, was finishing a job for wayne chalk painting. He had been temporarily loaned to
on november 10, 1996, at approximately 1700 hrs., employee #1 of niles street plumbing was checking for a natural gas leak n


                                                      Page 96
                                                          all


n 1/23/96, at approximately 1045 hours, employee #1 sustained a fatal shock when the wire cable he was pulling made contact
on march 18, 1996 at approximately 1530 hours, employee #1, at southwest contractors, was performing clean-up work adjace
on 6/25/96, at approximately 1050 hours, employee #1 sustained a fatal head injury. This injury occurred when the employee w
125780783 On February 14, 2001 at about 06:55 am an employee of S.O.S. Construction Inc. was fatally injured when he jump
On October 9, 2000 at about 2:30pm a roofer working for Curtis Roofing was fatally injured while roofing a two-story house at 2
On June 15, 2000, at about 2:00pm, a laborer working for Scharf Construction collapsed on roof of single-story private residenc
employee #1 pulled his pickup truck to the side of i-5 northbound and parked the vehicle. He stepped out of his vehicle and, for
#1 employee was on roof of 30 year old theater (15 feet) removing old plywood and insulation. He stepped on a loose 2 x 4 and
On April 18, 2000 at about 1605 hours employee #1, of Power Systems Testing Co., was using a cloth rag to clean dirt from ele
On December 4, 2000 at about 3:30 p.m., employee #1, of Pouk & Steinle Inc., was working on a power pole transferring condu
On February 15, 2001, at about 10:00 a.m., employee #1 of Midstate Steel Erectors, was working underneath a steel staircase
employee #1, an iron worker for midwest steel erection, inc., oakland, ca, was changing out steel bracing atop the cap of a ben
lrc electric co. 3379 ellington villa drive altadena, ca 91001 sic-1731 the above named individual was electrocuted while assistin
on 01/22/97, at around 0950 a.m. deceased employee #1 and employee #2 arrived at the demolition site in covina in order to s
on 01/22/97, at around 0950 a.m. deceased employee #1 and employee #2 arrived at the demolition site in covina in order to s
j. Cab & sons roofing, inc.sic code: 1761 4530 pacific way commerce, ca. 90040 victim was a roofer working on the roof of a ne
employee #1 was setting roof trusses on a house under construction when he fell approximately 22 ft off the edge of an unguar
employee #1 entered the basement of a home to check for a gas leak. The homeowner turned on the light, igniting the methan
employee stringing new transmission and distribution electric lines came into contact with a 7200 volt line and was electrocuted
a crew of employees was setting a 40-foot-long utility pole into a hole in the ground from a truck bed. The pole was at an angle
employee #1 was walking on a closed section of i-70 and was struck by an asphalt hauler. He died.
employees were sandblasting towers at an oxygen plant in a steel mill. Once they completed sandblasting one tower, they mov
employee installing new light fixtures when he came in contact with energized piece of equipment which electrocuted employee
two employees were putting away a ladder hoist. The ladder contacted a 69-kilovolt overhead power line. One of the employee
two employees were putting away a ladder hoist. The ladder contacted a 69-kilovolt overhead power line. One of the employee
on october 8, 1995, employee #1 was applying waterproofing to the exterior of a building from a two-point suspension scaffold.
worker fell installing insulation down on top of "q" decking that was just installed. He fell approximately 22 feet off the unprotecte
on december 9, 1995, employee #1, a 44-year-old field technician for nynex corporation, was standing next to his own legally p
on december 9, 1995, employee #1, a 44-year-old field technician for nynex corporation, was standing next to his own legally p
employee #1, a construction demolition laborer, and four coworkers were working in manhattan on temporary platforms made o
an asbestos abatement worker was clearing access to a work space where he was to install a plywood containment enclosure.
employees of roth's metal work, inc., were installing steel decking and angle brackets on the roof of a three-story building witho
employee was working installing and repairing stain glass window on a church from a sloped spanish clay tile roof 30 feet from
independent contractor was electrocuted when washing the ceiling inside an unoccupied building. He was working with a power
two employees working within a elevator shaft installing a 16 ft. 360 pound guiderail were standing on a wood work platform at
two employees working within a elevator shaft installing a 16 ft. 360 pound guiderail were standing on a wood work platform at
employee operating a bobcat model 753 was preforming demolition work on the second floor level of a garage building which h
employee was working on a tubular welded scaffol on a 5th floor, close to an uncovedred floor opening when one of the planks
on 10-24-96 at approx 8:30 am 2 workers were installing bars on a window on a shed. The shed was on the roof and used to en
employee #1 was dismantling water pumps and electrical panels at a pump house on the englewood golf course. It was a hot, h
Both the mechanic and the mechanics assistant were working underneath the tub grinder on this day in order to install and tigh
employees were closing a bridge painting site for the weekend. Barrels of hazardous waste were being lifted from the roadway
on may 28,1999 at approximately 13:30 an employee of a drywall company under contract with the general contractor was kille
INCIDENT: The following employees were on site that evening: 1. Ironworker - #1 2. Ironworker - #2 3. Ironworker - #3 4. Iron
On July 27, 2001, the northeast section of the residence located at 3 Calhoun Drive had only the roof rafters erected on the roo
employees #1 and #2 were installing sewer pipe (two running pumps) in a trench that was 12+ ft deep. An 8 ft high metal box w
employees #1 and #2 were installing sewer pipe (two running pumps) in a trench that was 12+ ft deep. An 8 ft high metal box w
on february 21, 1994, employee #1, who was normally assigned to the column crew, was temporarily assigned to the deck crew
employee #1 was walking along the shell-fill portion of a job site. He was looking over a work area that had to be filled with sand
employee #1 was a journeyman pipefitter with r. n. pyle contractors, inc. he had worked at this occupation for over 30 years and
at approximately 8:30 a.m. on may 21, 1994, employee #1 was tracking a crane over two 4 ft by 20 ft timber mats with a sheet
six employees on a derrick barge were repositioning an anchor for a dredge one mile off the coast of florida. Seas were 4 to 6 f


                                                       Page 97
                                                        all


six employees on a derrick barge were repositioning an anchor for a dredge one mile off the coast of florida. Seas were 4 to 6 f
six employees on a derrick barge were repositioning an anchor for a dredge one mile off the coast of florida. Seas were 4 to 6 f
the employees had gotten to the site at 7:00 am. The men were stripping off the old roof at the southwest corner of the building
employee #1, the owner of a painting company, and another employee were walking across a roof when the owner stepped on
at approximately 1:50 p.m. on february 5, 1994, employee #1 was operating an excavator. He was widening a retention pond w
on october 24, 1995, employee #1 was installing drywall from a scaffold platform that was 85 feet above the ground. The platfo
on august 18,1995 at 1:30 pm, employee #1 was at the fourth floor, south elevator shaft. While stripping the remaining forms, h
on 10-06-95 the deceased and two other installers were installing vinyl aluminum soffit along the eaves of a beer distribution co
on august 4, 1995, employees #1, #2, and #3 were working on interstate highway 10. They had been assigned to fill a washout
an employee was digging a ditch with a power operated ditchwitch. The purpose of digging the ditch was to bury some pvc pipe
two employees were finishing up their work at the end of the day. Employee number one was a helper and employee number tw
on october 23, 1995, employee #1 and two coworkers were forming the bridge deck of a new bridge under construction. The co
on august 2, 1996, employee number 1 was giving backing directions to a concrete truck driver who was positioning his truck to
employee #1, a pipe fitter working on a petroleum construction project, was using a torch to fabricate a hasp for a tool box in a
employee #1 was installing a storm water drain line at the mccreary county airport, clark hickman air field in pine knot, ky. He e
employee #1 was standing on a sears, roebuck and co., type I extension ladder that had been separated to make two 14 ft ladd
a power line foreman was working from an aerial lift, restringing an overhead power line. The line on the north side of the utility
a large culvert was being built for new highway construction. Employee #1 and three coworkers were working at 10 to 12 ft on t
at approximately 12:00 noon on december 23, 1994, employee #1 and employee #2 were cleaning a used 2,000 gallon tank wi
at approximately 12:00 noon on december 23, 1994, employee #1 and employee #2 were cleaning a used 2,000 gallon tank wi
an apprentice electrician was removing circuit breakers and cleaning out the switchgear cubicles and the receptacles from whic
on june 29, 1994, employee #1, a plasterer, was applying stucco to the exterior of a house. He was working from a 10 1/2 ft tub
on may 23, 1995, employee #1 sustained a groin injury while carrying a piece of 2 1/2 in. pipe at a job site. He underwent surge
an employee was moving an ingersoll rand rock driller (model no. 45) with its mast in the upright position. The mast contacted a
an employee was moving an ingersoll rand rock driller (model no. 45) with its mast in the upright position. The mast contacted a
employee #1 was watching a crysen employee retrieve a catalyst sample from the reactor of a mddw unit that had been purged
on february 10, 1995, employee #1 and a coworker were installing plywood decking on the second floor of a two-story residenc
at 11:15 a.m. on november 3, 1995, employee #1, a 19-year-old employee of hall plumbing and mechanical, was working in a 1
at approximately 2:30 p.m., employee #1 was helping build a chimney for a mountain cabin. He was on the 6:12 pitch roof peak
employee #1, a new driver, was being trained to operate a heavy dump truck when he ran off a causeway that was being exten
employee #1, a new driver, was being trained to operate a heavy dump truck when he ran off a causeway that was being exten
a telephone line worker was working from the bucket of an aerial lift. He was not wearing head protection or personal fall protec
employee #1, a trained and experienced tractor operator, failed to follow instructions for the use of gears and routing of a tracto
on july 1, 1994, employee #1, a trained, experienced truck driver, was transporting a modular home unit with a cab-over tractor
two employees were replacing a water tank at a residence. They had used a chevrolet 2-ton boom truck with a lifting capacity o
employee #1 was assembling trusses on the roof while positioned on the plate line of a house. When he stepped forward to rea
a 16 ft 9 in. truss boom weighing approximately 800 lb was stacked crossways on a stack of lumber approximately 4 ft 11 in. hi
at approximately 5:15 p.m. on november 9, 1992, employee #1, of turf construction company, was picking up traffic cones from
on june 14, 1993, employee #1 was standing on a flatbed truck trailer tending the hook and lifting chain of a pittman truck-moun
employee #1, an oiler on a heavy duty crawler backhoe (caterpillar model #245), had been the safety man for this piece of equi
victim #1 was the wife of the owner of gemini mechanical services, which did demos on chillers and related electrical gear. The
employee #1, a laborer, was killed while driving a water wagon on a construction project. The water truck had been involved in
at approximately 2:10 p.m. on sunday, june 21, 1992, employee #1 came to a job site where a heavy equipment operator had b
at about 2:35 p.m. on september 14, 1994, employee #1, a tile setter, was repairing/replacing brick veneer on the exterior wall o
at approximately 2:50 p.m. on march 10, 1994, at david goetden interstate building material in valencia, ca, employee #1, a labo
employee 1, a carpenter foreman, had stopped to assist two other employees in removing some debris from a roadway next to
employee 1, a laborer, was in the process of removing a 4'x 8' sheet of plywood that was part of the roof of a large warehouse b
employee 1, an electrical foreman, was in the process of connecting the electrical power to a motor of a pump for the landscap
employee run over by a grade all, operation of grade all backing up and ran over him. Grade all was equipped with a functioning
employee 1, a carpenter, was standing on the top plate of a wood framed wall while using a portable saw to trim the ends of roo
at approximately 8:00 a.m. on february 6, 1995, employee #1, a 46-year-old part-time roofer with more than 15 years of experie
at approximately 10:30 a.m. on november 30, 1992, employee #1, foreman and site supervisor for lyman dean/frame structures


                                                     Page 98
                                                         all


employee #1, a 56-year-old with prior steel erection experience, was standing on a 12 inch beam that was elevated 16 feet abo
employees #1 and a coworker were at an oil and gas well location performing a trenching operation. The coworker left the site f
employee #1 was operating a caterpillar d-9 with a ripper bar. Employee #2 was preparing to pick up dirt and transport the dirt t
employee #1 was operating a caterpillar d-9 with a ripper bar. Employee #2 was preparing to pick up dirt and transport the dirt t
an electrician was working on a 480-volt, 400-ampere panelboard. He was using a hydraulic knockout punch to make holes for
on 3-15-95 the employee's foreman and two employees were at the inter- section at the above address to relocate undergeoun
employee fell from scaffold inside a building, receiving massive head injuries causing death.
the employee fell from an elevated forklift. The employer did not provide a platform secured to the forklift, but used a wooden tr
the deceased came into contact with 14,400 volts of electrical power while working on a cable tv line. The guy wire became disl
employee was welding metal decking to structural steel on, and at, the edge of the roof canopy covering the third floor walkway
while marking off for rc channels on ceiling joists, employee fell from the third floor baclony to a concrete pad 21 feet below. Em
employee was assisting two other employees in a work crew while they were spraying oil at a cattle guard on a narrow two lane
employee #1 fell from the 6th rung of a twelve foot ladder and struck his head on a tile dfloor below. Employee was attempting
some employees of an electrical contractor were loading old utility poles onto a trailer. The poles had been stored beneath a 16
employee #1 was driving a tractor near the side of an embankment. The tractor went down the hill about 30 feet, rolled over on
employee #1 was driving a tractor near the side of an embankment. The tractor went down the hill about 30 feet, rolled over on
employee #1, an assistant serviceman, crawled under an idling 50,000 lb fuel/service truck to check the right rear spring u-bolts
employee #1 had clocked out from his shift and was walking to his car. A fixed crane was being dismantled on an adjacent con
employee #1 was assigned to sheet a roof. He was on the southwest corner of the roof, on a sheet panel that was not properly
employee #1 activated an elevator while leaning over the gate. The elevator ascended to the second floor, striking and killing em
on april 12, 1996, at approximately 11:30 am, employee #1 was traveling from the north east corner of the roof to the south wes
during the course of work, the crew had placed the barge on the south side of the existing dock. High tide occurred around 2:30
employees were removing sections of concrete from a flat roof that was 18.4 ft above the ground. The employees were working
employee #1, a construction worker, was operating lull equipment with the forks extended and the boom elevated when it overt
while working on a carpenter's bracket scaffold, employees #1 and #2 apparently overloaded the scaffold with roofing shingles.
while working on a carpenter's bracket scaffold, employees #1 and #2 apparently overloaded the scaffold with roofing shingles.
employee #1 was trapped in an 8 to 10 ft deep trench that collapsed while he was installing drainage pipes along the basement
worker removing a 4x8 sheet of plywood from a skylight opening when he stepped into the opening and fell approximately 30 fe
on april 3, 1996 at approximately 11:00 am, two workers were replacing a defective window at a customers home. The other wo
empleado estaba colocando una regla en plafon para empanetar. Empleado al bajar del andamio y caminar para pasar de un l
employees #1 and #2, of bradley w. hartman, were constructing a small brick wall and mail box pillar at a private residence on a
employees #1 and #2, of bradley w. hartman, were constructing a small brick wall and mail box pillar at a private residence on a
at approximately 11:45 a.m. on january 25, 1993, employee #1 was working underneath the falsework during a concrete pour. T
at approximately 3:50 p.m. on february 1, 1993, employee #1 was working on the roof of a 5-story building. While lifting the met
at approximately 7:45 a.m. on may 27, 1993, employee #1 was removing a skylight so that mastic could be applied to its base.
employee #1 was loading roofing material onto single story roof when he lost his balance and fell. He landed on the flat drivewa
at 11:00 a.m. on march 4, 1993, employee #1, a welder, was welding on a 90 degree elbow section of a newly-installed 20 in. p
employee #1, of bernel construction inc., was on the roof of a building under construction installing eight 36 in. by 10 ft long sky
at 2:15 p.m. on april 17, 1992, employee #1, a journeyman carpenter of local 1147, had elevated an approximately 515 lb meta
employee #1 fell from the top section of a two-piece extension ladder when it came loose from a morgan pump jack scaffold, w
two employees were laying out replacement heating duct. One of the employees entered a crawl space beneath a single-family
a one-third partner of an electrical contractor was troubleshooting an electrical problem on a conveyor. He contacted an energiz
at approximately 10:00 a.m. on january 17, 1993, employee #1, a roofer with over 30 years experience, was throwing asphalt te
at approximately 2:50 p.m. on december 23, 1993, employee #1 was working as a flagman for a construction crew that was ins
at around 10:30 a.m on may 14, 1993, employee #1, a carpenter, and employee #2, a foreman, were working on one of severa
at around 10:30 a.m on may 14, 1993, employee #1, a carpenter, and employee #2, a foreman, were working on one of severa
at around 3:15 p.m. on august 23, 1993, employee #1 and a coworker were preparing the bartmill 300 asphalt grinder for work
on may 21, 1993, employee #1, a dozer operator working alone, was run over by the dc.f caterpillar tractor he was operating. A
on may 19, 1997 at approximately 1430 hours when a 38 years old carpenter sustained serious injuries as a result of a 12'foot
an accident happened at an industrial wprksite of a roofing contractor who was performing a resurfacing job on an existing facto
employee #1 was operating a pavement roller weighing approximately 7,000 pounds, with roll-over protection attached. He was
s.g. welsh co., inc. p.o. box 326 murrieta, ca 92564 sic - 1771 on august 8, 1996, at about 9:55 a.m. an employee of s.g. welsh


                                                      Page 99
                                                          all


on january 31, 1995, employee #1 was working in a 36 in. diameter by 5 1/2 ft deep gasoline delivery manhole. His body was fo
employee #1 was installing rain gutters on the top floor of a five-story building under construction. He was standing on a flat led
a plumber was dispatched to a mobile home to make repairs. He had to crawl under the home to turn off the water. The wiring
j. Colon coatings 6047 carol avenue alta loma, ca 91701 sic -1799 on april 15, 1996, about 1:50 pm., an employee of j. colon co
american water well service, inc 33604 agua dulce cyn. Rd. Sic 1781 agua dulce ca. 91350 on the morning of 8 april 1996 two
american water well service, inc 33604 agua dulce cyn. Rd. Sic 1781 agua dulce ca. 91350 on the morning of 8 april 1996 two
an employee was on his second day of work at a jobsite, painting beams from a scaffold. He contacted the energized 480-volt r
at approximately 10:25 a.m. on april 21, 1995, employee #1, a laborer, was removing an old roof from a small single family dwe
at approximately 7:15 a.m. on june 5, 1995, employee #1, of assured concrete construction, inc., was assigned to repair a hydr
at approximately 8:40 a.m. on august 8, 1995, employee #1 was breaking apart waste cement chunks under a scaffolding and
a three-person crew was erecting light poles along an interstate highway and along frontage roads on the interstate. Two of the
a three-person crew was erecting light poles along an interstate highway and along frontage roads on the interstate. Two of the
a concrete pump truck operator was moving the boom on his truck, guided by a ground worker. The operator was standing on t
at approximately 1:30 p.m. on june 3, 1994, employee #1 and a coworker were preparing to disassemble the boom on an amer
at 1:30 p.m. on july 26, 1994, employee #1 was moving a board on a mobile scaffold while standing on the fourth rung. He fell b
employees #1 and #2, of j.r. turner construction, were traveling in a pickup truck from a job site to the office. As they traveled do
employees #1 and #2, of j.r. turner construction, were traveling in a pickup truck from a job site to the office. As they traveled do
employee #1 was moving a portion of an elevated mobile scaffold while working on the face of the west light rail tunnel. He was
employee #1, of j. c. compton contractors, inc., was attending to a paving machine on the side of interstate 84. When he had fin
at approximately 1:30 p.m. on november 15, 1995, employee #1 was atop a wood/web truss panel assisting in setting a 37 1/2
shortly after 2:00 pm on may 8, 1996, employees were installing sheet metal decking on the 3rd level of a steel structure buildin
employee #1 was operating a link belt 2700 track hoe at multnomah falls during freezing rain and snowy conditions. the snow h
on 11-26-96 10:00am worker #1 had climbed a 40 foot power pole and used a 27 foot piece of pvc pipe to open the cutout. He
on august 12, 1997, at approximately 2:30pm employee #1 was operating highway roller over stoned road surface and freshly o
on may 10, 1999, at approximately 10:30 am, employee #1 was traveling downhill on a 12 ton 1961 huber-warco static type roll
an electrician contacted an energized neutral conductor for a 277-volt circuit while he was moving a lighting fixture in a ceiling g
a vice president of a company was climbing a concrete form to check the work on a vault on the other side of the form. A 277-v
fall from 11 story
employee #1 was mowing the county right-of-way along a road in niles, ny. He was mowing a steep embankment with the mow
to drain water from a flooded swamp area, a work crew was clearing beaver dams from culverts that were under an old railroad
employee #1 was driving an endloader. The loader overturned, displacing him from his seat. He was pinned under the loader a
at approximately 4:30 p.m. on september 1, 1995, employee #1 was operating a john deere 4506 dozer down a steep hillside. I
two employees of a roofing contractor were extending an aluminum extension ladder when it contacted a 19.9-kilovolt overhead
two employees of a roofing contractor were extending an aluminum extension ladder when it contacted a 19.9-kilovolt overhead
on april 25, 1996 employees were working in the coffedam at pier #2. On the northwest end a 6 inch water pump was in place.
on april 16, 1996 at approximately 1:40 employee #1 and #2 were trapped while dismantling a coal tipple which prematurely col
on april 16, 1996 at approximately 1:40 employee #1 and #2 were trapped while dismantling a coal tipple which prematurely col
bridge support was placed ;under bridge. Chains taken loose from one end. Support fell on employee support weighed approim
on june 18, 1996 at approximately 4:45 p.m. employee #1 and employee #2 were part of a crew installing a double tee (floor pa
on june 18, 1996 at approximately 4:45 p.m. employee #1 and employee #2 were part of a crew installing a double tee (floor pa
employee was installing screws in metal frame building. The employee was holding to the metal building with his left hand and s
employee was descending ladder from level 3 to level 2 on july 18, 1996 when he fell approximately 25 ft. into elevator pit. The
employees were moving a 30 ft. long section of roller conveyor by lifting it off the floor with a forklift truck centered on the sectio
employee was in a 5-6 foot deep trench installing sewer pipe. Trench walls were vertical and no protective system in place. Afte
operating enloader with no rollover protection - steel beam fell on operator and killed him.
Two brothers were removing stringers from the bridge deck through the top opening of the bridge. One was on the bridge deck
during the operation of post tensioning a thread bar, the bar disengaged from the coupler resulting in the jack/ram end as well a
employee backing dumptruck equipped with rail gear down track with load of stone for rip rap collided with backhoe that was pa
employee was placing rock samples into the back of a pick-up truck and was backed into by a road grader. The employee was
employee was struck by hair-pin that fell approx. 10-20'ft from above employee. Hair-pin was being held above employee's hea
employee #l and #2 were preparing to remove a 225 amp breaker from a 1600 amp 277/480 volt square d company, power-sty
employee #l and #2 were preparing to remove a 225 amp breaker from a 1600 amp 277/480 volt square d company, power-sty


                                                      Page 100
                                                        all


employees had removed a cinder block structual support wall. This wall also supported the brick on the outside of the house. N
the deceased employee was in the process of erecting a temporary elevated work platform. He had tack welded a piece of ang
an employee was attempting to un-plug the chute that was used to move scrap roofing from the roof area to the dump truck be
employee was trapped in a trench cave in. There was no protective system in place along the vertical walls.
the employer was using a jsw bh80elc excavator with a demolition hammer attachment to chip away concrete so the company
employee #1 was installing single-ply pvc roof material on the flat roof of a warehouse. He sat down on a skylight with a 1/4 inc
employee #1 was setting up a traffic-control zone on md route 140. The traffic signal light in the area was going to be upgraded
employee #1 was stocking an 8:12 pitch roof on a 2 story house. As employee #1 was moving a bundle of roof shingles, he dro
equipment roolled over then strucy by: employee was operating a dresser dozer, model td-8e, sn007347, to level the top of a so
a painter was painting from a 30-ton overhead crane (model no. 30ton kdbet, serial no. 4302). The overhead crane was design
a worker of a construction contractor and an employee of a soft drink bottling company were working together. The contractor h
employee #1 was laying pipe in a 60 ft long by 3 ft wide by 4 to 11 ft deep trench. The side walls were vertical and there was no
two employees were performing roofing and gutter work. The employees had had no training in jobsite hazard recognition, and
two employees were performing roofing and gutter work. The employees had had no training in jobsite hazard recognition, and
an employee was performing a roofing renovation job. He was setting up a portable ladder-type material hoist (silent hoist co., i
a crew of employees was replacing a light pole. The new pole, which was 34 feet tall and which had a 15-foot-long arm attache
employee #1 of cambridge, md, was helping the owner of the company clear land to build a house. His assigned job was to ass
employee #1 of cambridge, md, was helping the owner of the company clear land to build a house. His assigned job was to ass
employee #1 of cambridge, md, was helping the owner of the company clear land to build a house. His assigned job was to ass
employee #1 climbed onto the 10:12 pitched roof over the garage to see where to begin removing leaves from the gutters. He w
on july 2, 1996, approximately 11:15 a.m., employee was moving metal siding through an opening on roof when he stepped ont
employees were removing road construction signs and cones from highway at the end of the work day at approximately 6:30 p.
employee struck by lightning.
employee struck by lightning.
employee struck by lightning.
employee struck by lightning.
on july 25, 1995, employee #1 was transporting mortar from one mason's area to another on a scaffold. Three planks shifted an
an electrician was assigned to work on transformers for a chiller. The transformers were located in the basement of a university
at approximately 9:15 a.m. on november 20, 1995, employee #1 and a coworker were erecting i-beams between concrete colu
at approximately 2:50 p.m. on november 6, 1995, employees #1, #2, and #3, of duggin excavation, were laying 48 in. drain pipe
at approximately 2:50 p.m. on november 6, 1995, employees #1, #2, and #3, of duggin excavation, were laying 48 in. drain pipe
at approximately 2:50 p.m. on november 6, 1995, employees #1, #2, and #3, of duggin excavation, were laying 48 in. drain pipe
on 7-28-97 employee #2 and #1 were loading explosives into the split hole drilled on 1/2 to 1 slope. Employee #3 was drilling ho
on 7-28-97 employee #2 and #1 were loading explosives into the split hole drilled on 1/2 to 1 slope. Employee #3 was drilling ho
on 7-28-97 employee #2 and #1 were loading explosives into the split hole drilled on 1/2 to 1 slope. Employee #3 was drilling ho
on 7-28-97 employee #2 and #1 were loading explosives into the split hole drilled on 1/2 to 1 slope. Employee #3 was drilling ho
the deceased employee was operating a scraper to grade a roadway in the construction of a subdivision. He fell off the scraper
employees 1 and 2 were in a 10-foot deep trench with vertical side walls when it collapsed.
employees 1 and 2 were in a 10-foot deep trench with vertical side walls when it collapsed.
employee #1 was apparently grading the lot for a new home on a ford 250c tractor when witnesses first saw him. He was next s
victim was putting up trusses on a 3-story apartment building when he fell approximately 30-feet to the ground and was also str
employee working in an aerial bucket on a rotating boom mounted on a service truck. The truck was parked on a roadside slan
deceased was down in a manhole guiding the top section in. The backhoe operator lifted the cabin and cable upward thinking b
employee #1 was repairing telephone cable on highway 27 south of harriman. After job was complete employee #2 noticed em
employee #1 was at construction site with the owner of the structure to survey future work. Employee #1 stepped inside building
employee #1, without approval, went to csx railroad to obtain a jlg man basket. Employee #1 was operating or moving the jlg m
on april 15, 1997, at approximately 10:00am, employee #1was sitting on the stairway sanding the stairway handrail. While sand
on september 13, 1997, at approximately 1:30 p.m. employee #1 and employee #2 were installing valley guttering at the roof's e
electrocution.
employee #1 and another employee were in the process of changing a light bulb at approximately a 42-foot elevation. the empl
a foreman for cfe, along with employees #1 and #2 were on the roof of the new central library at mtsu, dismantling the inside fo
on march 4, 1997, at approximately 11:00 a.m., employee #1 had entered a recently constructed manhole that was 8-feet deep


                                                    Page 101
                                                         all


victim was removing a pin from the left lower section of boom section when the boom fell onto his neck and shoulders.
victim fell from roof while installing flashing around the edge.
the deceased had been raised about 35 feet above the ground in wood box on shytrak forks with a bundle of 20 ft 3/4 inch copp
An employee was on top a scaffold platform getting a hammer and apparently lost her footing and fell down between the scaffo
an elevator was being checked for final inspection. The elevator rose above the floor section and when the employee looked un
employee was pulling sheets of metal roofing into place to be screwed down, stepped on insulation and fell 22 ft to concrete sla
the victim was struck by a felled tree that was being towed and became snagged and broke loose and flexed, striking the victim
an employee of wright brothers construction was operating a backhoe (caterpillar 225) in order to dig out an area for water drain
an employee of t. w. frierson, was working on the roof of a warehouse. The company was installing roof panels and insulation. H
An employee at commercial painting, was standing on a 12-foot ladder painting an overhang on the front of the entrance to the
four employees. one backhoe operator, one bulldozer operator and two laborers were site clearing 18 acres. The victim who wa
employee #1 was attempting to inflate a 16 in. tire that had been mounted on a 16 1/2 in. rim. During the inflation process, the t
on august 24, 1995, employee #1, of shaw steel structure, was installing 32 ft by 26 in., 20 gauge roofing panels from an elevat
ee 3.1 installing siding to sfr, from pump jack scaffold work platform (appro ht 8'4"), suffered seizure, collapsed fell through sing
van der haeghen construction co., inc. the employer is the framing/carpentry sub-contractor for the orinda intermediate school c
an electrician was installing air conditioning units on the roof of a 10 year old commercial building. The electrician was working
at approximately 5:30 a.m. on august 18, employee #1 was on a 6 ft high mobile scaffold removing metal soffit material. He had
a laborer was installing metal trim on a barn. A 7200-volt overhead power line was located 1.7 meters above the peak of the ba
employee #1 fell 20 ft from the roof of a house where he was working and landed on his head. Employee #1, who was not using
on october 14, 1995, employee #1, of varion oncology systems, and three employees of unique electronics were dismantling a
employee #1 and two coworkers had lifted a house with individual cranes and were holding the house while three other cowork
employees #1, #2 and #3 were killed by dynamite blasting. They had not been trained in the use of dynamite.
employees #1, #2 and #3 were killed by dynamite blasting. They had not been trained in the use of dynamite.
employees #1, #2 and #3 were killed by dynamite blasting. They had not been trained in the use of dynamite.
a construction laborer started to fall off a roof. He was apparently holding a piece of rain gutter at the time. The metal gutter con
on february 19th at approximately 11:15am four (4) employees were removing four sections of personnel hoist tower. Two (2) e
a dump truck with an obstructed view to the rear was being operated with a reverse signal alarm that was not distinguishable fr
on may 28, 1998, at approximately 8:30 a.m., on construction site at 2909 south campbell avenue, springfield, missouri, 65801.
On July 3, 2001, at aproximately 2:00 p.m. and employee was working on scaffold at aproximately 36 feet above the ground lev
Deceased was returning from an overnight job. He was driving his personal vehicle southbound on SR-395, approximately 5 m
The employees were setting up chicken pens on the first floor, which was 10 feet 5 inches above the basement. The employee
at 10:32 a.m. on august 30, 1994, employee #1 was working as a flagger on the east light rail project. She was standing on the
employee #1 was a union iron worker installing steel and limestone panels to the face of the federal court house under construc
employee #1 and a coworker were unloading 20 ft sheets of metal roofing material on a two-story, multi-family building. While u
on or about 10-15-06, a journeyman electrician and apprentice were installing flourescent lighting in a plant. The apprentice wa
employee #1, a construction worker, was crossing the highway after setting traffic signs on i-84 in waterbury, ct. He was struck
a heating, refrigeration, and air conditioning mechanic was working alone, servicing a residential air-conditioning unit. He was re
employee #1 was preparing to weld a series of six bar joists into position in a bay of a new building under construction. The bar
employee #1 and co-worker removed two grates covering a 68" square floor hole. A crane was used to remove these grates du
at about 11:30 a.m. on november 21, 1994, employee #1 of sierra west construction was part of a crew that was remodeling an
on highway 20, just west of penn valley, employees were cutting back the shoulder on the north side and filling in the shoulder o
an employee of a cable television company was working from an aerial lift. While he was working, an overhead power line fell o
on 5/8/96 at approximately 4:30pm on road 156 near zamora california, the body of the operator was found run over and dragg
struck in head by a falling object. Employees #1 and #2 both mason laborers were assigned by there foreman to take a scaffol
truck roll over: the victim was operating a caterpillar d-25-d end dump, moving excavated soil from new construction foundation
while installing a new roof, employees were spreading ballast and removing unwanted debris and lumber from the roof of a com
a foreman/master electrician was assigned to install lights along the side walls of an emergency exit corridor. (He was the only
at approximately 6:30 a.m. on june 7, 1994, employee #1, a foreman, entered a trench that was 8 feet 2 inches deep, 4 feet wid
employee #1 was using a laser transit to measure the grade of an excavation 101 ft long by 4 ft 1 in. deep by 5 ft 6 in. wide. The
fall from ladder, a 40' aluminum extension ladder, model #ae2240, manufactured by louisville ladder corporation, type 1a, was s
employee was working approximately 25' above ground on an aluminum ladder within 5 1/2' of a 7,970 volt high voltage line ap
Employees working approximately 14'3" on a wood pole pump jack scaffold fell when left pole snapped at a splice approximate


                                                     Page 102
                                                         all


Employees working approximately 14'3" on a wood pole pump jack scaffold fell when left pole snapped at a splice approximate
Employers York Roofing and Seasonair were working together installing HVAC units on the foof of a commercial building under
several employees erected platforms from the side of a scaffolding that was 4 ft wide by 10 ft long and 20 ft high. The employee
several employees erected platforms from the side of a scaffolding that was 4 ft wide by 10 ft long and 20 ft high. The employee
while painting four 22 ft wooden columns on the second story balcony of a three story building, employee #1, a 54-year-old pain
on august 29, 1994, employee #1, of de moura carpentry, was on a roof truss removing a 2 by 4 brace from a single family hom
on august 29, 1994, employee #1, of de moura carpentry, was on a roof truss removing a 2 by 4 brace from a single family hom
employee #1 was in the bucket of an aerial lift removing a light pole. While he was lifting the pole, employee #1 was catapulted
on january 19, 1995, employee #1, a driller superintendent, and a coworker, a driller's helper, were at a job site where they had
the superintendent for l.h. cranston and sons, inc., stated that employee #1 was locking the trailer door with a chain at the end o
employee #1 was standing between the front of his fuel truck and the front of a komatsu dump truck, model ha270-1. There wa
employee #1 was working in a 2 ft deep trench while excavating soil from the bottom 2 ft of a wall panel near a parking garage.
on april 18, 1995, employee #1 had completed the installation of drywall in a townhouse basement. While he was attempting to
a) Injured and others were installing new plywood roof sheathing over existing skip-sheathing, preparing to install a new compo
a) Climbed extension ladder to 25 ft. to retrieve paint brush. b) Standing on ladder at about 25 ft. level. c) Aluminum 35 ft. exten
a)Deceased was returning to work area with backhoe from driving to get crew's lunchboxes from crew truck at far end of job. b)
ER was boring A 2" x 130 Foot pipeline hole to be used for a water line, ER foreman was operating a ditchwitch JT1720 directio
ER was boring A 2" x 130 Foot pipeline hole to be used for a water line, ER foreman was operating a ditchwitch JT1720 directio
a) deceased was attempting to back transfer tractor to hook up trailer tongue to truck. b) deceased was standing at back of truc
a) Compacting fill dirt, leveling hillside to build deck around swimming pool b) Employee was operating compactor w/blade - ba
on march 19, 1997, at or about 1250 hours, employee #1 was working with two other employees who were shaking out the met
On 02-15-97 at approximately 1:10 am, a miner working in a mta tunnel construction project was killed. Said employee was wa
at 12:02 p.m. on december 9, 1995, employee #1 was inspecting the inside tubes of a boiler for a bid proposal when a large ac
employee #1, a boom truck operator was loading a muck rake attachment onto the flatbed of the boom truck using a bobcat 74
the victim re-aligning cones when a dump truck that was backing up ran over him. The back alarm was functioning. The victim
employee 1, a superintendent, and a foreman were attempting to align a concrete tilt-up panel which had been set in place and
employer 1, a carpenter leadman, was on top of a tilt-up wall panel to make sure the panels were plumb. He was stepping dow
Allied Technology Group, Inc. D1799-034-01 The employer was the general contractor for the store renovation work in San Ram
W.T. Cook Construction, Inc. D1799-023-00 Dirt Wall Cave-In. The employer is a grading and paving contractor. At the Moraga
a drywall installer was working on the second floor landing of a home. He was covering nail holes on the ceiling when he fell thr
on 08/24/98 at approximately 1830, an employee died following aa fall from a roof. The employer removes roofing materials an
on 10/21/99, at approximately 0830 hrs, an employee suffered an acromioclavicular separation of the left shoulder. He was tran
on 12/16/99 at about 10:15 pm an electrician working for snp electric was fatally injured while working at 4925 dewey drive, fair
On February 2, 2000 at about 10:00 am a roofer working for Metal Rood Company at 1545 Pleasant Grove Blvd., Roseville, CA
Marysville District 10 Levee: Crash and burn of a tractor off a levee. Two levee district workers were making a fire break while c
Per witnesses, measurements, interviews and visual observation the accident occurred as follows: On 06/09/01 four employees
The following is based on measurement interviews and photos and is a description of the accident that occurred on 8/27/01. On
the employees were assigned to level and finish the installation of false work on the construction site. They were under a main
the employees were assigned to level and finish the installation of false work on the construction site. They were under a main
the employees were assigned to level and finish the installation of false work on the construction site. They were under a main
the employees were finishing up the roofing job on the new house. Most of the roof was finished about four weeks prior to the a
the victim was working on the roof and was assigned to pick up metal trash on the flat surface only. He was assigned to clean a
the victim was assigned to apply joint compound and tape to the new drywall wall erected in the airplane hanger. He was workin
at approximately 3:00 p.m. on july 10, 1994, employee #2, of besco elevator service and repair, was lifting a 2,000 lb piston with
at approximately 3:00 p.m. on july 10, 1994, employee #2, of besco elevator service and repair, was lifting a 2,000 lb piston with
an electrical foreman for an electrical contractor was near a control room at a new transit authority headquarters building. He w
at approximately 12:45pm, ee#1 was performing his assigned task of "shooting ropes thru conduits". He inserted a "mouse" int
ee was working on 277 volt lighting circuit with power on. Came in contact with hot wires and was electrocuted.
on june 19, 1996, v was picking up traffic cones on roadway next to curb and storing in back of flat bed truck, driver of motor ve
chronology on december 6, 1996, plastering crew was fire proofing metal columns on 3rd floor, south side of building under con
employer is a cable tv installation service and the injured was employed there as a cable tv installer. The injured was putting a n
a power line worker was working on a 4160-volt circuit breaker. The employee was apparently performing tests inside the break


                                                     Page 103
                                                        all


on november 1, 1994, employee #1, of nyland plumbing, crawled under a floor space at long beach medical clinic to investigate
crane load fell on worker
on 08-15-96 about 1506, an employee was performing layout work for the construction of interior metal stud walls. While chalk-
on april 22,1998, at about 10.10 a.m.,an employee of walter c. smith company was fatally injured when an earth drilling machin
at approximately 1:00 p.m., on july 11, 1995, employee #1, a crane operator, was operating a 14.5-ton truck-mounted hydraulic
on 5/28/96 employee no. 1 along with two co-workers was moving a steel "i" beam that weighed 10,152 lb. The move was bein
on tuesday, february 11, 1997 at 1:00 p.m., employee no. 1 was working alone in a cellar at 3525 west 8th street, los angeles, c
employees numbered 1 and 2 were employed to help tear down a brick building. At everly level completely encircling the buildin
employees numbered 1 and 2 were employed to help tear down a brick building. At everly level completely encircling the buildin
on may 8, 1997 at approximately 10:20 am, employee no. 1 was checking the backhoe attachment to the bobcat he was opera
roerich painting inc., 401 n lombard street, ste. I, oxnard, ca 93030
on december 11, 1996 at about 11:21 am employee #1 was walking on a tug boat that was pushing two empty barges in san pa
employee was crushed when mobil home fell off jacks. The wheels and axles had been removed and the unit was not blocked.
struck by cable/ employee was positioned on a utility pole when a car struck the cable strand which was laid across the road. T
at 11:20 a.m. on december 17, 1994, employee #1, of mckay roofing co., inc., along with three coworkers and a foreman, were
at approximately 8:15 a.m. on october 25, 1994, employee #1, a roofer, was working on a garage roof. The employer had frame
at approximately 4:50 p.m. on december 20, 1994, employee #1 and several coworkers were backfilling a garage retaining wall
employee #1, of thomson mechanical corp., was connecting pipelines to condensate system pumps during a refinery turnaroun
EMPLOYEE PLUGGING 110 VOLT LAMP INTO ELECTRICAL EXTENSION CORD RECEIVED ELECTRICAL SHOCK WHIC
VICTIM TOUCHED 277 VOLT "LIVE" ELECTRICAL WIRES. UNKNOWN WHY HE TOUCHED THE WIRES. WIRES WERE P
EMPLOYEE 1, AN ELECTRICIAN, HAD BEEN WORKING ON A 277V LIGHTING SYSTEM FROM A LADDER. HE AND THE
EMPLOYEE 1 WAS ASSISTING IN PLACING PLASTIC SHEETING OVER WINDOW OPENINGS AT A HIGH-RISE HOTEL U
EMPLOYEE 1, AN ELECTRICIAN, WAS USING A METAL SNAKE TO PULL A DE- ENERGIZED WIRE THROUGH THE INSI
EMPLOYEE 1, A CONSTRUCTION SUPERINTENDENT, HAD ASCENDED A 20' HIGH LADDER TO CHECK SOME EQUIPM
employee entered an excavation approximately 8' deep, without cave-in protection or proper sloping for class "c" soil. Trench ca
on may 1, 1995, employee #1, of leblanc communications, inc., was ascending a communications tower to visually check a new
on september 13, 1995, employee #1 and two coworkers were installing a used mobile home at a private residence in white city
on january 10, 1995, employee #1, of first class homes, was helping a coworker place a jack stand under the tongue of a trailer
on november 22, 1996, at approximately 2:45 pm; employee #1 plastering a wall. Employee #1 worked on a wood pole scaffold
Employee #1 was working between a CMI asphalt planing machine, model #PR-800-7 and a Peterbilt dump truck, license #A19
between 1140-1149, 10-31-95 employee #1 was operating a white-freight- liner yard tractor owned by quality transportation ser
deceased was driving a bulldozer across a train bridge when he drove off the bridge and the dozer landed on him crushing him
employee 3.1 was spraying a foam type material on the board stock and trusses as a sealant. Employee 3.1 was not wearing a
On Feburary 7, 2000 at about 1:30pm employee #1 was in a scissors lift holding a tape measure. Employee #2 was on the wall
On Feburary 7, 2000 at about 1:30pm employee #1 was in a scissors lift holding a tape measure. Employee #2 was on the wall
on 08/22/96 at 1:30pm employee #1 was operating an ivy hi lift (marklift) installing insulation brackets in the ceiling of an amwa
employee was driving company vehicle to a work site, approximately 10-15 minutes. after leaving shop he pulled over to side o
3 employees were moving a 35 foot section of pipe from one location to another with a sideboom crane, the crane had a 26 foo
3 employees were moving a 35 foot section of pipe from one location to another with a sideboom crane, the crane had a 26 foo
on january 5, 1996 at about 8:05 am on the maluhia elderly housing project, an employee was on the ground getting a pallet loa
Employee was riding in the bucket of a tractor end loader. The operator tipped the bucket back causing a slight jerk, causing em
employee #1 was a laborer involved in building an all steel construction, industrial building. The employees were putting the she
on march 24, 1995, employee #1 and a coworker, both of batterton waterproofing inc., were working on the interior of a multi-bi
employees were in the process of laying metal decking on a structural steel building. Employees required to walk on top of the
on march 26, 1996, at approximately 11:00 a.m., employee #1 was assisting a hydraulic excavator operator remove a concrete
employee #1 was installing guarding over floor holes on the top (14th) floor of a building that was under construction. When he
the employee was a sheet metal worker working at a power generating plant. He was standing on a mounting bracket of a large
see narrative
an employee was hired by a crane owner to salvage items from a junkyard. For no apparent reason, he was adjusting the outrig
an employee was hired by a crane owner to salvage items from a junkyard. For no apparent reason, he was adjusting the outrig
at approximately 2:00 p.m. on january 31, 1995, employee #1 was replacing fluorescent light bulbs in room #322 at the chugach
employee was making a pipe connection in an excavation that was approximately 14' deep. There were two employees in the t


                                                    Page 104
                                                          all


west haven farms, lot #55, 4672 west 4450 south, west haven, utah. April 3, 1996 5:30 p.m. the injured employee, a 19 year old
employee was working in a trench that was over 12 feet deep. The trench had vertical sides. No protection from cave-in was be
at about noon on oct 22, 1996 employee was working on the roof of a small concession stand at saratoga springs, in utah coun
company was building the second of four concrete storage pits, that measured 98 feet square, 8 feet high, and 8 inches thick. T
on the 21st of june at approximately 10 am george allen fell 27 feet from a railing used for an overhead crane. The location is th
on august 14, 1997 at aprox. 1335 hours, an employee fell approx. 35-40 feet to the ground below. She was performing prep w
employees were hauling material on a trailer behind a semi-truck up a dirt road. When this road became too steep for the truck
An employee was grinding on the end of a pipe when a 10-ft steel I beam was brought over the area that he was working. The
employees were working on live overhead electrical lines behind building 106 at fort douglas in slc. This electrical line was eithe
deceased was operating a cement pumping truck when the boom came in contact of an overhead power line, which was rated
on may 22, 1998 at approx. 1215, employee #1 was cutting the flooring away from an overhead material handling conveyor gal
the employee was working on the top level of a five story building. They were about 80' from the ground. There was a steel cab
at the site, the contractor is doing construction of the new i-15 freeway. This site is currently at the concrete paving stage. The v
20 foot trench collapsed underneath a trench box
employee fell from roof
an employee (warren lamb), received an injury to the right side of his face and eye as a consequence of being struck by a #4 pi
employee was performing duties related to moving equipment up the pipeline right-of-way. The employee was operating a cate
An employee was helping place a stud wall on its anchor bolts, when he tripped and the wall came down on him crushing him b
employee fell from a roof approx. 22 feet in height, to the paved driveway below. The employee was accomplishing touch-up pa
an employee was standing at ground level engaged in touch up painting on a cinder block wall. The employee was standing be
an employee was standing at ground level engaged in touch up painting on a cinder block wall. The employee was standing be
geo pacific's crew was off-loading rolls of plastic liners from the truck. The site superintendent was on the truck in placing the st
the employee was pre-assembling wall panels, hammering at waist level, when he collapsed to the ground. Other employees in
the operator of a construction roller (compactor) was ejected from the roller as it started to slide sideways on a sloped edge of s
The deceased victim/employee was instructed to assemble a new scaffold, he climbed a "red- tagged" scaffold to obtain planki
Employee driving an empty articulating end-dump haulage truck (off-road type), lost control while driving downhill (10-12grade)
An employee was pulling on the wall with a back-hoe and chain. No one else was in the area. For unknown reasons he climbed
Working at approx the 130' level, an employee was using a come-a-long type hand hoist to relieve pressure from the wave quid
They were in the process of moving 20' long pieces of angle iron to the roof area, where they would later be installed as suppor
There were two workers spraying lacquer primer on woodwork inside of an apartment. One worker went out to the van and hea
The superintendent was standing on a crossbeam within the facility, handing plywood sheets/2x4s to employees on the outside
Decedent was driving between jobsites. While driving North on SR161 vehicle crossed centerline and collided head on with a s
the back hoe operator contacted the 7200 volt single phase primary electrical line and the laborer on the ground grabbed the ch
the back hoe operator contacted the 7200 volt single phase primary electrical line and the laborer on the ground grabbed the ch
on 05/22/97 at about 3:00 pm employee #1 suffered a heart attack and died.
Employee #1 left scheduled work location at approximately 1600 hours. He was found at approximately 1845 hours handing by
the employee received fatal injuries after falling 16' from an unguarded scaffold platform onto the cement floor below.
a supervisor and a helper were installing florescent lights in a mezzanine area. The supervisor was mounting the fixture and the
employee #1 was working in a bucket truck adjacent to a substation installing jumper cables, when he came into contact with liv
employee #1 was in the process of removing water from a metal tank by means of air pressure when the tank exploded. Emplo
employee #1 was performing his normal job duties of roofing. Employee #2 and other employee was unloading material from a
driver #1 was going to drive his loaded dump truck up to yard and dump. Driver #2 was backing his dump truck up to position fo
Employee #1 was driving southbound on Hwy 3 near Poulsbo Mile Post 52 when on coming vehicle crossed median into emplo
on 08/06/99 at 09:15 am decedent was part of a roofing crew that was removing a temporary roof cover from a large flat roof. D
employee #1 working on roof with no fall protection equipment being used, employee #1 for reasons unknown slipped and feel
employee 1 was delivering a double load of fill dirt to a jobsite. After dumping first load, he attached truck to transfer trailer. He
At approximately 1425 hours on 05/29/2001 an employee of Hillview Builders Inc., was injured due to a fall of 11 feet 8 inches (
at approximately 0815am, 9-16-1999, the foreman was spray painting a line on the asphalt. He walked around in front of the du
An employee was performing air nailing of finish trim on a second floor balcony while standing on a saw horse type scaffold wh
Worker was elevated above ground in aerial lift basket performing pressure washing of roof when his head made contact with 7
employee driving truck lost control and rolled the truck pinning employee inside the cab where died due asphyxiation due to com
25 yo male, with 3 weeks experience on site, was in a 9'6" deep by 6' wide excavation drilling holes for explosive placement. He


                                                      Page 105
                                                         all


an employee was working in an unshored unsloped trench when the trench collapsed on him.
no jurisdiction., no employees. All family members.
on august 1, 1996, at approximately 12:15 pm, an employee was vacuum cleaning mill scale out of three water troughs located
employee was repairing wind damaged wall framing. A section of wall that was standing fell and struck the employee on the he
employee #1 was working from a insulated bucket while holding onto the grounded guy wire, his head came in contact with the
employee fell from height suffered severe head trauma
employee #1 working in a elevated bucket truck when he came in contact with a energized line and was electrocuted.
employee working on apartment building being remodeled fell 34 feet from roof to ground.
an employee was conducting demolition work in and around an elevator hoistway. The employee was cutting steel car rails, cou
on june 24, 1997 at approximately 1:40 pm employee while returning to the back of the crane from getting a drink from the wate
accident abstract on august 3, 1997, at approximately 13:30 pm, located at 1300 murphy mill rd, nevada, mo, 64772, on the co
pulling pipe from exit hole,when pipe rode up on tong,both employees moved away from pipe,one employee hurt leg the other l
an employee was electrocuted when he drove the raised bed of his dump truck into a 79kv overhead power line. He was sprea
august 11, 1997 the victim did not return home from work when expected. His wife and her mother searched and found him de
employee performing lift in a reach all 5120 aerial basket in which a 336lbs pipe was attached to the side of the employee's bas
victim, one of five structural steel employees on construction site, was at the east end of a 24' steel I beam attempting to conne
an employee was killed while performing carpentry work on the roof when the purlin he was sitting on broke and he fell onto the
employee was killed at a construction site as he attempted to brace up an unstable brick wall that his company was in the proce
employee was installing decking on roof and fell thru open area .
a construction employer was installing all dielectric self-supporting (adss) fiber-optic cable on existing 69 kv electrical transmiss
employee was a flagger on a highway construction project. She had stopped 5 cars. A semi- trailer hit the 5th vehicle and bega
on or about july 29, 1998, at approximately 12:30pm, employees # 1 and # 2, were preparing to remove windows from the east
on or about july 29, 1998, at approximately 12:30pm, employees # 1 and # 2, were preparing to remove windows from the east
on 8/31/98 at approximately 9:00 am the employee/victim was walking along the outer (traffic) edge of a controlled highway zon
employee working on communcations tower, installing additional sections at a height og 260 ft when sheave cable seperated ca
employees working in trench with out sloping, shoring or bracing being present.trench collapsed trapping both employees and c
employees working in trench with out sloping, shoring or bracing being present.trench collapsed trapping both employees and c
employee was electrocuted while performing conversion operations at the substation at the city of odessa power plant. The dec
employee walking across a steel bar joist measuring 3 3/4" wide fell approximately 22' on dec. 4, 1998 at approximately 2:30pm
two employees were connecting a residential pipe to an existing gas line to ran a gas service installation to a house, when the t
two employees were working from the bucket of an aerial lift truck. The employees were tasked with tieing in de-energized over
two employees were working from the bucket of an aerial lift truck. The employees were tasked with tieing in de-energized over
employee fell approxiamately 32 feet when he was attempting to weld bridging on the bar joists.
employee landing materials on roof next to parapet 14 inches high. Employee back away from load as it was being lowered. Em
a general contractor specializing in waste water treatment facilities was constructing new clarifier pits. Two employees were ins
employee while attempted to tighten the nuts on the bolts holding the tower structure fell approximately 40 feet to his death.
employee was allegedly working on six foot ladder and may have suffered a heart attack.
an employee of the company was working in an unprotected trench. The employee was attempting to make a sewer line conne
Employee laying plastic on fresh concrete to prevent it from freezing. covered open stairwell with plastic and proceeded to walk
One employee was working from the bucket of an aerial lift truck. The employee was engaged in a process of tieing in a new ne
The deceased employee was standing/sitting on a 6" wide I-beam 14'6" above the concrete floor, prior to falling. The employee
Two employees were dismantling a crawler crane to be hauled to another site. The victim crawled under the lowered crane boo
Employee hit by car while removing road signs
On May 28, 2000, an employee was performing work on a company van that had been raised with a commercial jack and then
Employee working on air handling unit 100 feet in air. Employee fell 80 feet to death.
Employee was attempting to lay a sewer line in a trench that was improperly sloped without any other type of protective system
Employee was severly shocked when he got an aluminum ladder into a high line. He later died as a result of the accident.
Employee was working in a trench 8-9' deep without the presence of cave-in protection, when the trench collapsed. The employ
Employee # 1 backing dump truck in a closed off median of Hwy 63 struck employee #2 who was acting as spotter crushing em
Employee Seeding shoulder of Hwy turned tractor over crushing employee.
Employee was performing the process of jacking down the girders when he was handed down a jack from the the employee on
An employee of an excavation contractor was screening dirt for further use. The employer had recently bought a new portable s


                                                      Page 106
                                                         all


Job Site at 4500 Progress Place, Springfield Missouri- On January 5, 2001, at approximately 1:30 pm two employees, sheet me
A two-point suspension scaffold was hung approximately 23 feet above ground level. The two workers on the platform, which w
Employees were in the process of moving structural steel parts, using a 60 ton truck crane. The operator of the crane was mov
An estimator performing a pre-bid inspection fell through a skylight falling approx. 27'.
An employee was electrocuted when the pole that was to be changed out fell on to the digger derrick truck's extended boom an
On 05/25/01 at approximately 9:00 am an employee of a plumbing company was installing a new water line to a rental house. H
Employee was working on a pipe elbow suspended on a chain hoist. The elbow was 32 inch diameter stainless steel being inst
Employee was accessing a water tower by a boatswain's chair. The boatswain's chair did not have an independent lifeline. App
Two employees were in the process of moving a 925 rail inserter from a low boy trailer. One employee was operating the crane
Employee entered trench to inspect sewer line.Boulder fell off trench face striking employee .
employee # 1 was working on a roofing crew performing reroof work on a structurally unsafe roof. Employee # 1 was walking ac
ironworker struck by overhead beam while booming basket lift backwards resulting in asphyxia and death. Employee was caug
union painter, age 30, was sandblasting structural steel under the bridge deck while working on a suspended work platform. Pa
employee #1 was finishing a concrete driveway on a single family dwelling progressing from the garage area to the highway. Em
on march 21, 1997, at approximately 0700, employee #1 was on the roof to get the serial number of a new sprayer in order to s
three employees were doing steel erection. They were bolting a diaphragm onto a beam. One steel erector was on the beam tie
three employees were doing steel erection. They were bolting a diaphragm onto a beam. One steel erector was on the beam tie
victim climbed beyond the minimum distance requirement for live-line work on an utility pole and touched the "live wire" with his
employee was operating a tracked crawler/loader when a previously felled tree struck employee in the cab. The tree had proba
fall from roof - 38 ft.
this accident occurred because of the over pressurization of a nonvented, spent 55 gallon chemical drum, containing residue, w
the victim was working from a 12 foot step ladder. He was inside a large water containment structure which was under construc
employee was installing vinyl siding of a single story shed. The shed was located next to the driveway with a grassy area betwe
abstract for arthur tower fatality, the job was constructing a 1000ft tower for a local tv station. The bulk of the tower had been b
person jumped into the trench to clean out some dirt, covering an sewer pipe and the trench caved in covering the individual.
on tuesday 4-20-99 & 11:15 am, employee # 1 was performing leading edge work on a new warehouse building roof. Employee
two employees were electrocuted while working on 2400 volt lines. They were working the circuit bare handed as if it were dead
two employees were electrocuted while working on 2400 volt lines. They were working the circuit bare handed as if it were dead
crane tipped while lifting roof trusses.
on october 13, 1999 an employee age 28 was involved in an accident while riding on the tailgate of a pickup truck. He was ridin
employee struck by the bucket of the backhoe while in the trench.
Employee # 1 was dismantling an overhead traveling crane, while free standing without fall protection on top of the bridge end t
Employees were installing duct work inside an enclosed awning. The awning was 13 1/2 feet above the outside dock floor. The
Double fatality - employees #1 and #2 were electrocuted while installing a street light pole at the entrance to a parking lot from L
Double fatality - employees #1 and #2 were electrocuted while installing a street light pole at the entrance to a parking lot from L
Construction project, securing structural steel for a warehouse. The victim was working in an elevated aerial lift, 36 feet above t
On May 24, 2000, a 43 year old service technician, from a heating and cooling services and repair company, was electrocuted
Employee was using a stepladder by leaning it against the wall without spreading and locking it. When employee descended la
Employee #1 was working with employee #2 on a residential roof replacing shingles. They were attempting to chalk a line acros
On 2-22-01 at a manufacturing site, a contracting company, that has had a long standing contract with the manufacturer for per
On 2-16-01 at approximately 11:10am, employee #1 was positioned 6 feet above a work platform, up a rebar wall of a concrete
Employee #1 was in a trench approximately 13' deep preparing to guide the landing of a concrete culvert when the south wall o
Employees were working in a excavation, 13 feet deep. They were installing sewer lines. They were at a spot where a small line
Employee #1 was performing drywall operations with one other employee at a residential construction project. Employees were
a two (2) ton steel plate was being lifted into an excavation, by a caterpillar backhoe, with a hook and chain. The hook became
employee was removing a split-rim tire from a standard dump truck when the tire exploded striking the employee on the forehea
employee #1 was operating a jack hammer removing asphalt pavement from a section of closed highway during a nighttime op
employee #1 was operating a jack hammer removing asphalt pavement from a section of closed highway during a nighttime op
accident victim was in the process of erecting an aluminum pump jack scaffold in front of private residence on 8/10/96 and was
on 5/4/96 & 1:17pm, employee #1, entered a truss area near the top of a railroad electrical tower, in order to paint an area of th
victim was riding in the bucket of a rubber tire backhoe when he was dropped or fell from the bucket and landed on his head 8
employee fell from a ladder was impaled through the leg upon a fence. He then struck his head on the concrete sidewalk.


                                                     Page 107
                                                          all


employee was working on a patio roof/ platfrom 90 feet above the ground. Employee was not protected by any fall arrest system
on 9/30/97 & approximately 8:30am, laborer travis miller, age climbed to the top of an aluminum extension ladder to retrieve a b
employee was working on roof of a hangar. He was removing the old roof tar paper which had been cut just previously with a m
man was killed
employees were placing a 25 foot high metal light pole on top of an 18 inch cement base at the construction site for the meado
employee #1 was awarded a contract to remove the old and install a new roof on a residential bi-level home. Employee #1 was
self-employed contractor, working alone, installing a drainage line in a thirteen foot deep, three foot wide excavation was crushe
two employees of an elevator maintenance company attempting to lower an elevator from the fifth floor of an industrial building
two employees of an elevator maintenance company attempting to lower an elevator from the fifth floor of an industrial building
d'annunzio & sons, inc. were contracted by the n.j. turnpike authority to repair sections of the turnpike. While in the process, em
famous building inc. was contracted to erect a 110,000 sq ft pre-engineered building for barrett companies in jersey cit, new jer
on march 4, 1999, at approximately 10:30am, employee #1 was in the process of obtaining scrap material (reportedly a piece o
employee was measuring the linear ft. of yellow tape used to mark off a new traffic pattern. The tape was beyond the last drum
on 10/6/99 & approximately 10:30pm, accident victim was killed during demolition operations of a two (2) story, 464,850 sq.ft w
On 4/14/00 & approximately 1:32pm, an employee who was involved in a rigging operation for an upcoming lift of a container do
Employee was in the process of starting a tractor. The tractor would not start, so he told the operator to get in the cab while he
The driver of a tractor that was attached to a dump trailer with high lift capability, was killed after the truck he was operating tipp
Employee fatality injured when struck by compressor. Employees were attempting to load a compressor on a flatbed truck whe
Employee was struck and killed when bulldozer backed up and he was caught and pulled under the track of the bulldozer.
Boom of a drill rig was being raised to drill a test well. The boom contacted a 26KV overhead line and energized the truck body.
Employee (mason foreman) was on the outriggers of a tubular frame scaffold 60 ft above the surface. The area was properly p
An employee of a concrete contractor involved with unloading a mud buggy onto a temporary staging platform at the 7th floor fr
Employee was working on an apartment house roof approximately 50 feet high when he slipped on debris and fell head first to
A carpenter backed through an unguarded floor opening at the 3rd floor and fell approximately 25 feet down to the concrete bas
employee, 29, was fatally injured at 2:00 pm on 5/17/96 when the bare copper wire on the bosch 11305 chipping hammer made
accidental fall from ladder. After losing balance on ladder, employee struck back of head on top of fiber drum that had a metal r
on or about 1/26/96, at approximately 02:30 p.m., employee #1 was critically burned in the chest, face and arm from an electric
employee #1 was fatally injured on an interstate highway by several vehicles while assigned to sweep up light debris in a closed
employee #1 and #2 were working from the attic level of the 3rd floor of a building which had been condemned due to a fire.the
employee #1 and #2 were working from the attic level of the 3rd floor of a building which had been condemned due to a fire.the
employee #1 was fatally injured and employee #2 was seriously injured on 7/1/96 when struck by hardboard roof insulation that
employee #1 was fatally injured and employee #2 was seriously injured on 7/1/96 when struck by hardboard roof insulation that
employee #1 was run over by the left front track of an asphalt grinding machine.
at approximately 10:30 p.m. on october 25, 1996, an employee was in the process of removing forms from pier #6 on lake shor
employee #1 received a fatal 7200 volt electrical shock while attempted to cradle the conveyor system of a rotec truck mounted
the victim , who was the owner of the company,was struck on the head by a large piece of concrete which was dislodged from t
on december 18, 1996, at approximately 9:30pm, employee #1 was plastering and painting the 3rd floor stairway in a school. T
on or about february 1, 1997, employee #1 was installing siding on a house. Employee #1 was approximately 9'3 above the gro
on june 30, 1997, at approximately 12:30 p.m., employee #1 was cutting a hole for a skylight, measuring 4'x5'x10", in the metal
victim was using a caterpillar track type front end loader to remove an 8 inch i-beam which was 28 feet long and had a 4inch dia
employee was fatally injured on july 8, 1997 when the masonry wall he was standing under collapsed onto him.
employee was installing a new tv cable line into a residence with his ladder leaning away from the residence against the overlas
employee was working on the partial demolition of a bridge - felt dizzy and light headed - collapsed on the way to the truck - init
employer and one employer are the two employees who died from falling from this scaffold. After consulting with the area direc
employee (laborer) was fatally injured on august 10, 1998, when a piece of roofing material fell 30 feet to the ground from a wh
fire and police department were called to the scene to respond to a call regarding a man who had fallen. The owner of the gen
an employee performing touch up painting from a communication tower had on only one lanyard and a safety belt. The snapho
employee operating semi dump trailer drove forward with the trailer raised and contacted 7200 volt electrical line.
two employees stripping forms from below the bridge while in an aerial lift placed on a barge over the chicago river fell from the
two employees stripping forms from below the bridge while in an aerial lift placed on a barge over the chicago river fell from the
the contractor was on site to dismantle existing and build new balconies. The balcony being constructed where the victim fell fro
victim fell from the top of a pipe rack (over 25 feet) to the parking lot area.


                                                      Page 108
                                                         all


two plumbers were installing 6" return hot water line inside an elevator shaft opening starting at the 6th floor 66 feet above the b
employee fell 27 feet through an opening in a walkway.
Laborer received crushing head injuries when caught between car dumper arm and railcar. Employee was attaching a holddow
The hoistway door's window was missing and the call buttons were not working. An employee's head was in the window when t
Employee fell from either the 26th or 27th floor while, apparently, climbing over the guardrails attached to the wall forms.
Two employees, (one journeyman lineman and one 1st step apprentice) were changing out bell insualtors on a three phase, de
Two employees, (one journeyman lineman and one 1st step apprentice) were changing out bell insualtors on a three phase, de
The owner and his father are in business and worked for the building developer on various projects. The three story apartment
dead
Two men were tuckpointing from the platform level of a two-point suspension scaffold when the cable wire used to suspend the
Employee was carrying a bundle of roofing shingles on his shoulder while accessing a roof via a ladder. Victim fell to the ground
Employee walked into an area where windows had not yet been installed in the skybox area of the Chicago Speedway spectato
The job entailed the demolition and reconstruction of a bridge located over a highway. A dump truck was used to catch concret
Self employed siding contractor erected a ladder jack scaffold around power lines to install siding, facia, and soffit on a new hou
Employee was electrocuted after apparently connecting the grounding lead of a 220 volt washer/dryer unit to one of the energiz
An employee (owner's son) fell from the 26th floor of a new construction condominium building approximately 200 feet to the ga
on september 25, 1997 at approximately 11:45 am mr. martin chavez chaparro, dob 12/4/64, an employee of construction cont
an employee working for fulfer electric was taping insulation to duct work in a church, when he fell through the ceiling and struc
on march 30, 1998, a crew of workers from bolar equipment service arrived in carlsbad, nm for a routine canopy erection job at
an employee was electrocuted while attempting to remove a live power line from a power pole that he and the rest of the crew w
on june 22, 1998, at approximately 1115 am, mr. hipolito estrada sanchez, a member of a b & h maintenance and construction
on september 1, 1998, a crew of workers from lane plumbing co. Inc. arrived in ruidoso, nm to work on completing a sewer line
the victim was crushed under the boom of a crane that he and other employees were disassembling, when he removed both pi
a line man was hanging a cable across a highway with the assistance of two other co-workers. While up on the pole, the line m
an employee was killed when a roll of insulation on a reel upon which he was sitting rotated, pitching him off of the roof of the b
on july 1, 1999, six road construction employees were preparing the subgrade of a road intersection for final compaction before
employee was behind a truck in preparation to unload it , when he instructed a fellow worker to back the vehicle up, and he was
On June 1, 2000 a crew of workers for Sarcon Construction Corporation arrived in Eldorado, NM to continue framing the Vista G
On 8/31/00, an employee entered the work site an began to unload a semi-trailer full of steal beams and trusses. The employee
On November 13, Jaynes Corporation reported that an employee had died as a result of an accident that took place on Novem
A steel worker working at approximately 11' was working a steel joist into place when he fell from the elevated surface to the flo
At approximately 15:00 on June 18, 2001, Gary L. Ochs was preparing to repair a water well when he was using a sledgehamm
An employee was part of the crew that was assigned to replace a 10' by 20' metal frame bridge back across the irrigation ditch
On August 30, 2001, it was reported that at approximately 11:20 P.M., August 29, 2001, an employee of University Mechanica
employees were in the process of dismantling large metal tanks. The process involved pushing the ends of the tanks into the ce
employee died of exposure to the inhalation of motor vehicle exhaust fumes. This was not on a construction site, victim was sitt
employee #1 was attempting to set an outrigger (pivot leg) for a semi-trailer portable rock crushing unit. Employee #1 removed
steel erection worker performing metal decking work to structural steel fell 30 feet from the steel joist on the one-story gymnasi
employee working in a trench seven feet deep, 30 inches wide and 45 feet long, was leveling and sloping the bottom, when he
on or about 1/9/98, an employee of starostka construction, inc., was crushed by a grain distributor/diffuser while working on the
an employee was hauling dirt from the lake area to the city dump area. The employee apparently turned too quickly causing the
apprentice ironworker was welding a clip to a 4 x 4 steel column, finished the weld, walked across the beam to access a ladder
two individuals electrocuted when pulling fiber optic cable and something contacted the overhead power lines, 13,000 volts. An
two individuals electrocuted when pulling fiber optic cable and something contacted the overhead power lines, 13,000 volts. An
two individuals electrocuted when pulling fiber optic cable and something contacted the overhead power lines, 13,000 volts. An
werner construction co - sic: 1611 on july 21, 1998 at approximately 7:00 p.m., employee was operating a ingersoll rand roller, l
the omaha area office was called initially by the area director who had heard something on the radio. The office contacted the s
the omaha area office was called initially by the area director who had heard something on the radio. The office contacted the s
on 09/14/98, at approximately 10:30am, employee #1 was down in a trench performing manhole installation operations. Appare
the victim was connecting 4 inch water line in a trench when the trench collasped pinning the employee in the trench.
the deceased's head struck the concrete floor when he fell 5 1/2 feet from the top of a baler machine. He was taken to the hosp
on 18 march 1999 at approximately 12:00 p.m. employees were using the forklift boom to access the roof. Witness states that


                                                     Page 109
                                                         all


employee #1 of kaw valley builders was standing on concrete roof tree signaling crane operator, employee #2 of brb contractor
employee #1 and employee #2 were dismantling a crane boom. Employee #1 pulled out the cotter pins from the boom pins and
employees of two trucking companies were working on a road construction site hauling dirt from one area to another to build th
on 07/31/99 at approximately 08:20 am, employee #1 was attempting to secure the top pulley of a "new england" boom ladder.
the employee was walking by an intact arrangement of concrete pilings which had been exposed while digging the excavation.
Employee #1 was an operator of what is termed a "water wagon" on a new road construction project. The water wagon is a Cat
Employee #1 held a production type meeting at the beginning of the work day to assign tasks. Employee #1 was scheduled to g
On 10/09/200 at approximately 12:20 p.m., four employees from Rupert Construction were sealing cracks on Highway 50 as pa
Employee #1 and #2 worked for a company who installed sewer lines. The company would install the sewer lines and the utility
Employee #1 and #2 worked for a company who installed sewer lines. The company would install the sewer lines and the utility
Employee 01 was operating a mobile scissor lift on uneven terrain when the lift fell over causing fatal injuries to employee 01. E
Employee #1 and Employee #2 were working on a roof as part of a crew constructing an addition to an existing hospital at appr
Employee #1 was part of a 4 man crew attempting to run communications lines when Employee 1 mistakenly cut into a 13,000
Construction site on south side of Beatrice, NE. Construction of Highway 77 bridge over railroad tracks. Victim arrived on the si
on 6-22-96, approximately 1115 hrs, the victim was assisting with the demolition of a gyro spiral freezer. The demolition require
on 6-22-96, approximately 1115 hrs, the victim was assisting with the demolition of a gyro spiral freezer. The demolition require
on 6-22-96, approximately 1115 hrs, the victim was assisting with the demolition of a gyro spiral freezer. The demolition require
male employee number 1, age 31, was fatality injured by rolling, unsecured backhoe when equipment rolled backwards into wo
on 3-31-97, at approximately 9:30 am, the employee was working on a mobile scaffold, at a height of approximately 9 feet, 4 in
on 11-15-97 at approximately 12:40 pm, employee #1 was driving a dump truck full of fill dirt across a railroad track, while empl
employee was picking up garden hose when struck by a ford truck with dump body that was backing up with a non-working bac
the accident involved a mobile home set-up crew that was in the process of repositioning a mobile home. The mobile home wa
the accident involved a mobile home set-up crew that was in the process of repositioning a mobile home. The mobile home wa
the accident involved a mobile home set-up crew that was in the process of repositioning a mobile home. The mobile home wa
on or about 1400, 15 june 1998, the victim was operating a kamatsu motor grader owned by overcash gravel & grading compan
the worksite was an existing residential dwelling, which had been previously moved to this location within the last couple of yea
The victim worked to install exterior insulation on apartment buildings. He was working in a unsecured 3 sided wooden trash/de
a worker while attempting to rework a section of ceiling rafters for a tray fell 10 feet to the lower surface after sawing the heade
abatemaster environmental, inc.- sic 1795 on july 14, 1999 at approximately 1030 am, employee was working in a crew of 12 m
a crew of four men were in the process of installing the last 10 of 80 skylights to be installed on the roof of a warehouse. The cr
deceased came into contact with electricity.
the deceased included the owner of the company and two employees. The three men died as a result of a fall of approximately
the deceased included the owner of the company and two employees. The three men died as a result of a fall of approximately
the deceased included the owner of the company and two employees. The three men died as a result of a fall of approximately
On or about 1330 hrs on January 31, 2001 an employee (age 41) while sitting on a top plate of an interior wall, and working with
A crew of three people were in the process of reroofing the private residence located at the jobsite. The crew consisted of three
Fall to lower level On August 20th, 2001 an employee fell for the second floor of a residential home in Linville, NC. He was work
five employees struck by tractor trailer
five employees struck by tractor trailer
five employees struck by tractor trailer
five employees struck by tractor trailer
five employees struck by tractor trailer
employee #1 was working in an elevated bucket approximatley eleven feet above the ground splicing telephone cables. He was
WORKER PERFORMING ROOFING WORK FELL 14 FEET, 4 INCHES FROM THE EDGE OF A FLAT ROOF. HE WAS ALL
Employee fell 27 feet from roof to ground
Two Employees Were In The Process Of Setting 2/30-Foot Aluminum Extension Ladders Up To Install Gutters On A New Apar
Two Employees Were In The Process Of Setting 2/30-Foot Aluminum Extension Ladders Up To Install Gutters On A New Apar
Employee #1 fell through the gypsum roof deck of a school building, while removing the exterior surface of the roof. The gypsum
employee of dare were placing erosion control on fields, when hydro ax and owner was asked to clear some land for them. Em
employee #1 was up on a scissor lift approximately 20 feet in the air. He was power washing the side of a building. The scissor
employee contacted overhead power line with aluminum ladder.
employee was killed when the forklift he was operating overturned. He was traveling with the forks up high and made a sharp tu


                                                     Page 110
                                                        all


employee had been cleaning underneath a large industrial dryer. While he was cleaning under the dryer, another employee was
employees were working on the third floor of a new school. They were laying cement blocks, it started to rain harder and the wa
on august 2, 1999, between 9:20 am and 9:59 am, an employee was electrocuted while working on a water pump at the bottom
Employee was tightening straps which were holding down four large steel pipes on a flat bed trailer on the side of the road. A m
on aug 5, 96 at approximately 3:25 pm, employee number # 1 was doing quality control and touch up paint work of bolts under
fall from scaffold while sandblasting
on july 3, 1997, three workers were performing minor repairs to a low-slope roof preparing it for resurfacing. Two of the three em
an employee was asphyxiated when he entered a "water vault".
the deceased was helping to push a 7 foot window through a doorway on the second floor when the window hit the bottom plate
owner of rd steel erectors was walking on a open web truss when he slipped on a un-welded joist and fell approximately 16 fee
The deceased age 42 was on the approximately 15 feet ground to eave height 4:12 pitch roof when he ran and jumped off of th
an employee was on an unsecured steel beam installing top plate. The beam shifted and the employee fell and the steel beam
on june 16, 1998, at approximately 3 pm, employee #1 was preparing to wire in a vapor light to the ceiling of a wire manufacturi
an employee was working on a roof landing equipment for a tower installation and fell 110' from the roof.
a flagger was on the road flagging traffic, no barrerls or directional signs were up or posted and a vehicle hit her.
employees were erecting a communications tower approximately 180 feet high. An employee was attempting to rappel down fro
an employee was placing roof trash in the chute of the dumpster at an approximate height of 18' to the ground. The roof had a
nextel site oh-1280-c2 / youngstown 2, 975 bears den road, youngstown, ohio: june 24, 1999, two employees (tower hand #1 a
at approximately 8:00 am on july 18, 1999 an ironworker working for nerone & son's, inc. fell to his death from a height of 26'-8
The deceased age 50, was operating an aerial lift when he was thrown from the basket per eye witnesses. Employees who had
an employee, while applying cellulose insulation into the exterior walls of a two-story house, was struck by an adjacent ladder a
A 75 ton Manitowoc Crane with a load or rebar was overloaded and tipped at a construction site. In iron worker was hit and kille
On 5/25/00 around 7:16 pm the owner of Golden Concrete & Construction Co. was crushed by a bulldozer while loading a traile
Employees were installing a new sanitary sewer at an approximate depth of 15 feet without trench safeguards in use. A cave-in
An employee was operating a dual drum roller compactor that turned over while compacting aggregate at the side of a newly pa
A crew of three men and a truck driver was removing old sidewalk curbing. The o loading the old concrete curb onto a truck. Th
The deceased was struck by a maintenance vehicle that was backing up on closed down lanes of the Ohio Turnpike. There we
An employee was wrapping tape around a high voltage cable termination on a switch when his elbow came in contact with an a
On a road construction site on a major highway an employee was hit and killed when a water truck backed up and hit him.
Employee replacing roof sheathing stepped on an unsecured piece of sheathing which kicked out from under him resulting in h
The company was installing a new running track at the Stow-Monroe Falls High School. The rubberized running track was outs
employee, decedent, was one of two foreman of a crew of seven, engaged in roofing a large flat roof of a new drug store under
on 7-25-96 at approximately 5:55-p.m., an employee (victim) was crushed to death while attempting to drive a track type bulldo
underground pipeline employees were cutting concrete pavement with a hand held portable gasoline powered "stihl" masonry s
on 2/2/98 employee #1 was working in a trench 8 to 10 feet deep in type "c" soil. A large portion of the trench caved in burying e
employee fell 20 feet to ground level from building truss. Employee was helping fork lift operator remove pallet from the forks. T
employee was electrocuted while acceding to the roof top. Employee reached out and touched the high voltage power line.
employee was spraying traffic lines on a closed section of hwy i-94. Employee had his back towards traffic and was inside the b
the owner of m.l. condon dragged the caterpillar grader to the rear of his shop with a case 350 dozer. The owner who was work
employee was loading a bulldozer onto a trailer. The bulldozer slipped and fell off the trailer crushing the employee under it.
Employee went down into trench to cap off old sewer line. Side wall came in burying the employee under approx. 5' of dirt. Emp
The employee was working in the road way placing grade stakes in a high traffic area. The employer's sub contractor was dum
Employees were rigging the boom extension on Peco tower crane when employee #1 was crushed between the queen's mast a
3 employees were in a man basket elevated 280 feet above the ground. They were in the process of guiding a large roof sectio
3 employees were in a man basket elevated 280 feet above the ground. They were in the process of guiding a large roof sectio
3 employees were in a man basket elevated 280 feet above the ground. They were in the process of guiding a large roof sectio
Victim fell from the top of a third-story wall while placing roof trusses. When the wind caught the truss, the employee moved ou
employee fell from roof.
the owner of the company was electrocuted and the boom operator was injured when the fully extended truck mounted boom s
the owner of the company was electrocuted and the boom operator was injured when the fully extended truck mounted boom s
employee felt dizzy was laid down and 911 called. Employee sufferred heart attack and died at the hospital.
Fatal Accident 1/8/98 - OUTSIDE OSHA'S JURISDICTION An Independent Sub-Contractor Truck Driver outside of OSHA's Ju


                                                    Page 111
                                                          all


the victim had separated the 'live' line in a junction box containing multiple live circuits, leaving the remaining 'live' wires 'uncapp
1.the cause of death was attributed to a 6ft fall from a stairwell retaining wall. Also, a suspended scaffold was staged 20ft above
on 5/4/99 Guy Pratt, inc. was paving the westbound shoulder of route 347, between broadway and crown street, port jefferson s
During an excavation operation an employee was electrocuted while installing an engineered metal support system. The emplo
(a) Employees was crushed by overturned forklift truck(LULL)
employee was standig in the skytrack bucket at a height of 36 feet when it capsize. The employee died because of the blows he
employee was fixing the hyraulic system of the dump truck. While performing this duty the dump fell and pinched the head of em
employess were installing storm sewer pipes in a 20 feet deep excavation. One of the walls collapsed and trapped two employe
The employee was worked in a tubular scaffold at 9'of heith, in the instalation of the sprinkler. He fell down receved baack cran
the employee fell down in a excavation.
The workman head remained pucture between the door and the largebox of the vihicule.
The employee worked with Northstar Communication, Inc., as a cable tv lines installer, had an electrical contact with four lines
Two employees was working in a tubular scaffold, at 70'of height approximate. They had the hammerhead in theirs body, but th
Employee that worked like steel structural men, fell down from approximate 90'of heigth.
employee no. 1 was a first day employee working as a laborer. Employee no.1 was engaged in moving and erecting scaffolds.
on tuesday, april 16, 1996, at approximately 10:00 am, employee 1 and employee 2 had removed the lose downspout from the
on tuesday, april 16, 1996, at approximately 10:00 am, employee 1 and employee 2 had removed the lose downspout from the
on tuesday, april 16, 1996, at approximately 10:00 am, employee 1 and employee 2 had removed the lose downspout from the
three employees were installing roof trusses to a newly constructed residential home. As the employees were hoisting the end t
employee no.1 was an employee of a roofing company. It was the first day the company was working on the jobsite. Employee
employee no. 1 was engaged in light residential construction repair, installing a new window. No witnesses saw the victim fall. T
this employer was engaged in laying 4" pipe for atlanta gas light co. They were trenching 4' to 4 1/2 ft. deep and double jointing
employees engaged in roof renovation and repair. Victim had removed a piece of roofing from the roof's peak, and dropped it o
employee #1 was working on bridge helping to install brackets that will support the water line. Employee #1 stepped on a piece
employee 1 was working in an aerial lift bucket, completing construction on a power distribution line. While upgrading from a sin
one of the laborers was shovelling debris off the roadway onto the median when the operator of a dump truck accidentally ran o
a mechanic was called in from the field to come out to the site to change a defective hydraulic cylinder on the blaw-knox aspha
employee # 1 was working on demolishing metal and concrete block structure, and was standing on a lower roof of the main st
on 8/4/97 at approximately 4:30 p.m. worker "1" descended into a 12' manhole that was part of a sewer system project in a resi
on 8/4/97 at approximately 4:30 p.m. worker "1" descended into a 12' manhole that was part of a sewer system project in a resi
on 8/4/97 at approximately 4:30 p.m. worker "1" descended into a 12' manhole that was part of a sewer system project in a resi
employee 1 and 2 were riding in the cab of a 1979 ford dump truck and employee 3 and 4 were riding in the bed of the dump tru
on december 12, 1997, around 11:15 a.m., four employees were in the process of constructing piers to set a 14' x 80' section o
employee #1 was working on the seventh floor level of an office building under construction. The building was in the process of
an employee accidentally tripped and fell through one of the skylight as he was heading back to his work area after retrieving a
on september 19, 1998 at approximately 12:15 p.m., an employee, who was in the process of cleaning a tar mixer, was found c
a framer fell inside the house, approximately nineteen feet, to the first floor (concrete foundation) while installing the ceiling joist
employee 1 was leaning over the top rail of a tubular scaffold to retrieve a bucket filled with stucco material from employee 2, lo
an employee was working at an elevation of 24 feet to the outside of a building under construction and 20 feet to the inside of th
employee #1 was in the process of installing a new ballast in a light fixture in a men's restroom. Employee #1 was working from
two tower workers were killed when the fall line slipped off the shaft of a capstan hoist while being hoisted to the ground. The fa
two tower workers were killed when the fall line slipped off the shaft of a capstan hoist while being hoisted to the ground. The fa
employee 1 and employee 2 were instructed by the foreman to repair a segment of the safety cable that was drooping to the flo
two employees while working 50' above the next level fell to their deaths when the bleacher section they were working on fell.
two employees while working 50' above the next level fell to their deaths when the bleacher section they were working on fell.
employees were installing insulation and corrugated metal roofing on a low-sloped stell frame roof. Employees were laying out
on 03/02/99 at approximately 09:30 an employee was crushed by heavy ductile iron piping while performing activities involving
employee was installing fireproofing insulation inside a plenum when he stepped on the gypsum board which broke. Employee
an employee was spraying sunflex, a waterproofing substance inside of a 7 x 5 x 9 foot concrete stoop when he collapsed on th
an employee was fatally injured when he was struck from behid by a truck. The employee was inside the traffic cones which we
roofing contractor had repair crew out to replace roof decking on a roof that was leaking. The roof deck to be replaced was with
on july 22, 1999 at approximately 2:00 p.m. an employee was installing a manhole collar adjacent to dallas highway (120) in ma


                                                      Page 112
                                                         all


employee #1 had mounted a genie superlift materials handler as a personnel lifting platform. Employee #1 had placed a 4 foot
employee was doing masonry work around a door frame on the eighth floor of a door opening of a parking garage being built fo
two roofers were placing a modified roof system on top of an existing roof. The roof level was approx. 40 feet. The employer ha
one employee was fatally killed when some of the soil along the north wall of the excavation collapsed and covered the employ
on september 10, 1999, at approximately 8:30 a.m. an employee was following behind a motor grader, which was being used to
employee was fatally electrocuted while replacing a 7 multi-phase, mini-transformer electrical ballast of a light fixture inside a dr
employees #1, #2, and #3 were on the hek single mast climbing platform at a height of &70 feet. Employees #1 and #3 were ge
At approx. 2:45 pm on 9/29/00, an employee was applying a base coat for a stucco application from the 5th level of a system sc
Employee was standing on edge of low sloped roof of newly framed three-story building. Employee was holding a large piece o
worker 1 and 2 were on opposite side of an office building nailing a 43' span truss while worker 3 stood along the outer wall of t
Employee operating vibratory roller in reverse and ran off the road bed onto a incline, employee proceeded forward on the inclin
At approx. 10:00 a.m. on 5/5/00, two employees were erecting a diagonal wind brace (structural member) on two knife plates (c
Employee 1, 2, and 3 were instructed to construct a 8' by 12' office inside of a manufacturing plant that produces steel frames.
Employee 1 was cutting drywall and employee 2 and 3 were hanging the section above a 10' brick wall in the girl's locker room
At approximately 5:00 p.m. on 1/22/01, 5 employees of Escobar roofing were working on the top of the Atlanta History Center ro
At approximately 5:56 p.m., two employees were in the bucket of a line truck aerial lift preparing to install an aerial marker on o
At approximately 5:56 p.m., two employees were in the bucket of a line truck aerial lift preparing to install an aerial marker on o
Employee was hit by dump truck. Dump truck was going up a hill when the brakes failed and the truck rolled back down the hill
Employee was on scissors lift platform on the ninth floor. Lift continued to rise and employee got neck caught between concrete
Employee 1 and 2 were using a fixed ladder to gain access to areas of the pipe to re-tape the installation that had started to pee
Employee 1 failed to extend his outriggers before he extended the boom of a 75-Ton crane to lift up some pipes. As he extende
on 08/05/96 at approximately 11:15 a.m., employee #1 went back to the roof top where he was instructed to connect up a new
on december 6, 1996 at approximately 4:00 p.m., while employee #1 was breaking concrete with a jackhammer in a trench/exc
the employer was using a northwest 95 wt crawler dragline which had been walked onto a spud barge to dig a wide space to vir
employees were working on anchor barge 82 with the boom/"a" frame laying at an approximate 60 to 65 degree angle. The end
the third (3rd) phase of construction consisted of a large concrete foundation with upright concrete columns to support the stee
an employee was welding bar joists onto the steel frame of a classroom under construction. The employee had climbed onto an
on 12/24/97, at approximately 9:20 am, two employees were attempting to load a 10,000 gallon tank, partially filled with emulsio
on the first day back after an extended medical leave (back injury), the employee was working on a 2-3 level scaffold, 12-13 ft a
on july 7, 1998 employees were installing central air conditioning equipment in a residential house without turning power off. Da
employees were doing lay-out work on the roadway, taking measurements, laying string line, and painting striping on the road.
an employee on his first day on the job was installing insulation and steel decking on the roof of a one-story warehouse under c
employee number 1 was electrocuted when the windmill propeller that he was grinding by hand contact, became energized whe
employees working in a trench 8 to 10 feet deep were not protected by an adequate employee protective system. The north wa
the employee was operating a caterpillar motorgrader, model no. 140-g, grading a surface after some water line work to reform
an employee was struck on the head by a load-bearing steel beam. A portable classroom building, riding on the steel beam, ha
An employee was installing 17 inch wide pan roofing and fiberglass insulation. The employee unhooked his lanyard, failed to re
an employee entered a nine ft. deep manhole to apply sealant to the connecting concrete rings. This was the last and the deep
Two employees were riding on the bumper of a one ton pick-up truck as is was being driven in reverse. The vehicle was backin
A decking crew was installing steel decking panels on the roof of a church parish hall expansion project. The installation of the
The employer was performing highway shoulder work on the shoulder of the South bound lane of Hwy 77. The outside lane of t
The nested maintenance contractor had additional workers at this refinery to finish a turnaround of the sulfur recovery complex
The nested maintenance contractor had additional workers at this refinery to finish a turnaround of the sulfur recovery complex
Three employees released ratchet strapping securing two layers of 10 inch steel pipe to a flat-bed trailer. The employee releasi
Employee was assisting the removal of cable reels from a reel trailer by tilting the trailer backwards. After the reels were remov
Welder was Tungsten Inert Gas Welding in a confined space at a refinery and suffered Argon asphyxiation.
An employee was under the bucket of a skid steer loader when the bucket came down, striking him on the head. The Daewoo s
An employee entered a 17 foot deep sewer manhole. The employee was not wearing a respirator or SCBA. The employee was
an employee of p & c painting company fell from a scaffold, approximately seven feet from the water, while painting a boathous
The owner of the company was in the process of carrying a section of rainspouting (guttering) up a ladder, when one end of the
on 30 june 1996 employee was operating a cement spreader on a road construction project. The brake system was an air-hydr
employee was attempting to mark a sewer manhole cover by spray painting the cover when he was crushed by a belly dump tru


                                                      Page 113
                                                         all


Employer was contracted to drill a water well. At the time of accident the driller and the driller helper were unloading well casing
a dump truck that weighed approximately 20 to 22 tons drove across a bridge that was designated as having a 8 ton load limit.
At the time of the accident, the involved employee was working alone at the equipment yard to prepare to haul a load of gravel
a worker was attempting to weld a ladder on a steel tank mounted on a vehicle. The tank contained gilsonite, a flammable liquid
a worker was attempting to weld a ladder on a steel tank mounted on a vehicle. The tank contained gilsonite, a flammable liquid
employee fell off of structural steel over 25' high causing traumatic injuries to his head. Company was cited for lack of fall prote
employee cut and held onto a guy wire that came in contact with a 7.2 kv distribution line.
a pipe layer was in a trench box in an excavation approximately 17 feet deep. The excavator track hoe operator was attempting
employee fell from roof 16 feet to the ground when securing roof panels to metal roof.
two employees who were engaged in water well drilling were working in the vicinity of overhead powerlines. The boom of the dr
an employee attempted to retrieve/store supplies/tools/equipment on the superstructure of a tracked excavator. He approached
a worker had been performing a demolition job at gem state lumber located in julietta, id. The worker was from schussler const
a pipe layer was working in an excavation when an excavator operator swung the bucket of the excavator over him. The bucke
this death was not job related, this death occurred as a result of a heart attack.
an employee was standing on the skid of helicopter while performing work task re a fiber optic cable on top of h structure used
ee killed in the cab of a tracked excavator by a large falling tree branch while pushing over cottonwood trees.
Stake hopper was runover by a scraper that was reversing.
Employee was stripping the rubber lining from a storage tank with a 36,000 psi water blasting lance . The employee was struck
Employee was putting air in tire of scraper that was parked directly behind service truck. Service truck was parked in an area th
employees were lowering scaffold and scaffold brackets inside a water tank, john stapleton, 29, fell off a scaffold platform at the
on july 18, 1997 at approximately 2:30 pm, employee #1 climbed a 30 ft. fiberglass extension ladder to help assemble the last 1
employee #1 had stop the operator of a skytrack forklift to give him further instructions on the moving of some material. The op
employee # 1, a journeyman electrican, was killed when an adjacent skytrac (industrial truck) overturned and struck the employ
on december 16, 1997 at approximately 5:40 pm, employee #1 was killed when an approximate 2,300 lb. counterweight fell and
a construction crew were installing a high voltage line rate 750kv in a rural prat of the state of arkansas when employee # 1 was
a crew of 5 employees was moving a large piece of electrical switch gear on rollers. The equipment toppled, striking two emplo
the deceased was unrolling an air hose while walking backwards on the mill roof. He stepped off of the mill roof onto the train s
on july 8, 1998 at approximately 8:00 a.m., employee #1 was working from a 6 ft. fiberglass ladder making final tie-ins of 2' x 4'
employee # 1 was part of a crew installing metal roofing over insulation 30 feet above ground level. Employee # 1 was at the le
employee # 1 was operatimg a bull float on a bridge deck when the form gave way, causing the bridge deck to cave in. Employ
employee #1 was working with a road crew on highway 62 west of mountain home, ar. removing highway lines with a stripping
during a welding operation near a slop lube tank, an explosion occurred resulting in the deaths of three (3) contractor employee
during a welding operation near a slop lube tank, an explosion occurred resulting in the deaths of three (3) contractor employee
during a welding operation near a slop lube tank, an explosion occurred resulting in the deaths of three (3) contractor employee
while a crew was positioning a templet in place for a cofferdam on the white river prior to entering the mississippi river it tipped
an employee received a fatal electrical shock while assessing a work assignment.
Employee #1 was a trainee electrician assisting a journeyman electrician in the removing some 480 volt electrical equipment fro
two construction workers were installing an 8-inch diameter pvc sewer line in an excavation that ranged from eight to nine feet d
Two linemen were in a 2 man bucket working on a line when it came into contact with an energized line that ran perpendicular t
on july 28, 1999 at approximately 10:00 am, employees #1 and #2 were inside an approximately 8' x 14.5' x 5'7" deep bell hole
on july 28, 1999 at approximately 10:00 am, employees #1 and #2 were inside an approximately 8' x 14.5' x 5'7" deep bell hole
Employee # 1 was killed when he interred into a restricted area and was strucked by a computered operated palettizered forklif
The company was contracted to install new sewer bypass lines at this site. The new pipe was being laid approximately 8-10 fee
Deceased was walking on unfinished wall of building under construction. Deceased fell head first approximately 13 feet to conc
On March 1, 2000 at approximately 6:15 p.m., Employee #1 was standing between a welding trailer and a Grove swing around
On March 24, 2000, at approximately 9:00 a.m., Employee #1 was on the upper level of a telecommunication tower that was un
An employee was walking backwards on a bar joist while "dragging" floor decking approximately 17 feet above a concrete floor
Victim pulling out a telephone line from the reel and laid it along side of Redhill Rd. As he turned and walked away, a truck cam
Victim was on a steel beam, and fell for unknown reason to concrete pad below, striking head on a installed steel beam on the
An employee fell approximately 240 feet from his work station at the top of a telecommunications tower to the ground below. Th
Employee was working on a third floor open I-beam structure. He was assisting in staging a load of floor decking when he was
On October 2, 2000 at approximately 4:45 pm, Employees #1 and #2 were working inside the right lane on an interstate highwa


                                                     Page 114
                                                         all


On October 2, 2000 at approximately 4:45 pm, Employees #1 and #2 were working inside the right lane on an interstate highwa
Employee was patrolling a transmission line, 69 kv and got within 12-18 inches of a limb hanging on the line due to an ice storm
Employee working out of a basket in a bucket truck on a single phase line. Attempted to unhook a jumper wire and was electro
Self employed contractor was cutting Gip board on a decked roof when he stepped back and fell 28 feet to the ground. After hit
The employer and his son were re-installing an old dishwasher and a partial floor replacement at a home in the Hillcrest Area. T
an employee was tearing off roofing material when the material he was pulling gave way. The employee fell back through an op
on july 2, 1996, just before 12:55 pm, employee was working as a flagman on construction crew along a stretch of highway. He
employee was helping crane operator move a precast concrete slab. The crane contacted a 34,500 volt overhead power line an
at approximately 5:00pm on september 11, 1996, the deceased and another individual were using a mechanical "grave digger"
an employee was replacing water pipes in an existing apartment building. He was using a trouble light as a flexible cord to prov
the employee was painting a 128 foot high water tower. He was on the top of the tower tied off with a personal fall arrest system
on 5/27/97 workers were involved in decking the roof of a new mcdonald's restaurant. At about 11:45 a.m., a hole was cut in an
two workers where climbing aluminum ladders while carrying a 65 foot length of an aluminum gutter when one end of the gutter
two workers where climbing aluminum ladders while carrying a 65 foot length of an aluminum gutter when one end of the gutter
the deceased employee had removed bolts on a section of a bucket elevator legg approximately 80 feet from the ground. When
the deceased employee was walking on a graded surface toward a dump truck that was backing to a "skimmer" machine. The
two employees had been involved in stressing post tension cables for a parking lot ramp with a "power team" hydraulic post ten
Two ironworkers were moving a 3'w x 36'l section of roof decking towards a 6'w x 36'l hole. The hole in the roof decking was a
two cranes were attempting to lift a concrete beam weighing approximately 54,700 pounds. The east crane was a 70 ton truck
this fatality took place on a project which consisted of the construction of a new single family home (stick built). The framing pro
on june 8, 1999 at approximately 12:00 noon, an employee collapsed when returning to work after a break. The work he had be
the deceased employee was apparently struck by a truck mounted derrick during the process of removing a concrete base for a
on september 29, 1999, two employees of multi-spray systems inc. were pressure washing the siding of norwood church at 239
two employees were working in an unshored trench running from east to west approximately 13 ft. deep, 5 ft. wide, and 61 ft. lo
Two carpenters were installing new support beams on an existing water slide. The employees were working off of a twelve inch
An employee was working on the first floor level while cross members were being placed and connected to the columns. The c
An employee was installing mansard metal roof shingles and ridge caps on a parapet area of the roof, extending out 60 inches
Employee #1 was flagging on a two lane road construction project. A six mile stretch of two lane highway had been resurfaced
Two employees were in the process of repositioning an concrete ornamental deer located next to a well located at a private res
Two employees were in the process of repositioning an concrete ornamental deer located next to a well located at a private res
Employee #1 was working from a Skyhook Aerial Crane with a manbasket attached to the end of the boom. He was approxima
On July 30, 2001 a truck driver and a traffic control laborer were moving traffic control signs with a 1994 Chevrolet C2500, flatb
An employee was in the process of maneuvering his aerial lift bucket into position in order to power-wash the exterior brick wall
employee was in the process of dismantling an faa tower when he fell approximately 62 feet to the ground level below.
the victim had worked for age corporation since 1965. At time of his death he was employed as a grade stake foreman on high
The owner of sykora construction stated that he has been in the construction business for approximately fifteen years and that
the victim stood under the raised bucket of a skid steer loader. The bucket came down upon the victim causing him to sustain s
the victim placed himself between the elevated box and frame of a back dump truck. The box came down crushing the victim b
the victim was installing soffit and facia on a 3 story barracks when he rotated the articulating boom and basket around and con
the employee was wearing a negative pressure respirator for protection from muratic acid mist and/or vapors while applying the
on or about 03/15/99 two employees were in the process of moving a manually propelled scaffold when it contacted a 4700 volt
an employee was operating a tandem axle dump box truck on a section of hwy 50 that was under construction. The employee d
the victim was working in a trench approximately nine feet deep with near vertical side walls when a trench wall collapsed on th
employees were engaged in the installation of roof sheeting on a single tier steel structure. The victim attempted to push down
employee was struck by a train when he drove the grader off the semi trailer onto a railroad track.
the employee was working in an excavation and was electrocuted. A pump was being used in the excavation to remove water.
on 08/04/99 an employee working on a road construction site was struck by a dump box truck. The employee stepped into the
victim was lubricating the drive train on the peterbilt tractor. The driver returned and not realizing that the victim was working un
Two asphalt hauling trucks collided head-on in a construction zone. The resulting crash and fire killed both drivers.
Two asphalt hauling trucks collided head-on in a construction zone. The resulting crash and fire killed both drivers.
Employee fell through a floor hole. He fell approximately 128 feet to his death.
A three-story apartment building under construction collapsed when struck by high winds. Five employees were hospitalized of


                                                      Page 115
                                                         all


A three-story apartment building under construction collapsed when struck by high winds. Five employees were hospitalized of
A three-story apartment building under construction collapsed when struck by high winds. Five employees were hospitalized of
A three-story apartment building under construction collapsed when struck by high winds. Five employees were hospitalized of
A three-story apartment building under construction collapsed when struck by high winds. Five employees were hospitalized of
The employee was placing materials on the third level and fell through a stairwell opening.
employee #1 was working on a paving crew in the north bound left lane of i-440 n. just north of the intersection of i-440 and wad
employee #1 and his partner were involved with performing minor repairs to television cable equipment. Employee #1 had been
employee had a heart attack while operating the dumping controls of a dump truck, which was dumping a load of waste sulfur,
at approximately 4:45 pm on 10/23/96 at the construction site of the learning center at 1397 hurdles mill road in roxboro employ
employee was working for a construction company, completing some of the work left to be done on a building that was already
employee #1(driver) left truck to run inside building to pick up a small piece of insulation to place in the window of the truck on t
on 5/22/97 an electrician working for howe electrical contractor's inc. fell from a mobile tubular framed scaffold from a platform
the deceased was working with two coworkers; all of whom had the sme supervisor. These employees of sunlife systems, inc.
on 05/15/97, employee #1 was involved in the erection of a communications tower located at 1567 stonewall springs road in ala
working from a truck mounted bucket 15 ft. above paved road surface, a class I lineman (employee #1) was removing an alumi
employee was attempting to access the top buck of a universal manufacturing co., 5' by 5' by 6 1/2', tubular welded frame scaff
date of birth 10-10-67, a visiting cousin of the owner (not an employee), was on the roof of the jobsite, suffered a massive suba
employee fell from ladder while working inside an elevator shaft.
three employees were involved with attaching waterproofing paper to the outside of a single family dwelling while doing residen
the power transmission & distribution work crew was relocating a section of three-phase overhead lines. Two linemen, employe
On December 18, 1997, employees #1 and #2 were assisting in the the placement of 16" I. D. water line into a 9' deep trench. A
On December 18, 1997, employees #1 and #2 were assisting in the the placement of 16" I. D. water line into a 9' deep trench. A
employee #1 was performing spray painting of an epoxy paint to the structural steel members of a cement hopper at a height o
employee was found at the bottom of the incline to the scrap asphalt pile and appeared to have been run over by the truck that
lineman installing cable tv line. Was not wearing pertective gloves. Line being handled came into contact with live wire.
employee was transferring electrical power transmission lines from an old pole to a new pole. After completing almost all of the
in process of setting up a double wide mobile home when it shifted off the foundation piers falling on an employee.
employee fell through an unsecured roof panel and struck the swimming pool wall and floor 27' below.
worker #1, victim, mounted scaffold from fifth floor window opening. Worker #1 was preparing to perform welding operations on
on june 9, 1999 at approximately 1:30 p.m., four employees of Victor Riveria were positioning a gable end on the edge of a plat
on june 9, 1999 at approximately 1:30 p.m., four employees of Victor Riveria were positioning a gable end on the edge of a plat
on june 9, 1999 at approximately 1:30 p.m., four employees of Victor Riveria were positioning a gable end on the edge of a plat
on july 21, 1999 at approximately 3:00 pm leon elliott (deceased), concrete finisher, collapsed and died later that afternoon. The
employee came into contact with a 277 volt single phase circuit while looping wires between ceiling fixtures and junction box.
employee had finished laying brick for the day and was walking along the scaffold when a witness stated that the employee see
three employees were applying c1010 primer to gym floor, when vapors from the primer reached the lel, and ignited with open f
On the day of the accident, 03/09/00, work began at approximately 7:00 a.m. At approximately 2:45 in the afternoon, the spotte
On July 11, 2000 at approximately 2:40 pm an employee cleaning the 2nd floor of a 2 story townhouse that was under construc
Employee was elevated 20 feet to 3rd floor of hotel under construction, in job-made wooden box (work platform), 8 x 4 ft, 3 side
On 8/31/00 employees of Hudson Roofing were continuing work on the repair of a roof on a private residence located at 2095 K
Accident Synopsis: Work began that day with the crew arriving at the Piedmont EMC substation, approximately three miles from
On November 07, 2000 at approximately 1:30 pm an employee was working on a scaffold fell and sustained fatal injuries. The
Employee #1 was fatally injured due to a fall from an overhead canopy that was being erected at the jobsite. Employee was per
Employee was winching piling from shore, 200 ft., out to pier, when rope came off winch-head; employee got caught in "bite" of
Employee 1 working on first floor level clearing dirt and mud in corridor. Second floor had a masonry wall being constructed on
The incident occurred on 02/21/01 at approximately 02:30 PM. The site of the incident was located a 111 Blueberry Hill Road, E
Employee was struck-by hydro-blasting nozzle and high water pressure.
1. Employees were installing a 8 inch PVC water line on Hwy 50 in Onslow County. The Trench was normally deep enough to p
On 04/17/01, at about 02:00 PM, victim 1 was working in the bottom of a trench, approximately 500' long x 30" wide x 5 1/2' to 8
The incident occurred on 04/10/01 at approximately 4:00 PM. The site of the incident was located at 733 Bell Fork Road, Jacks
On 05/23/01, victim was working at New Hanover Regional Medical Center, in Wilmington, N.C. The victim was standing in the
Victim 1 was replacing a wood power pole and was in the process of swapping all conductors/phases from the old pole to the n


                                                     Page 116
                                                        all


ee 1 was a laborer at a construction site and was about to enter the structure being built when he was struck on the head by a f
employees were being lowered in a personnel basket attached to a drum hoist. The basket was supported on guy wires for a 20
employees were being lowered in a personnel basket attached to a drum hoist. The basket was supported on guy wires for a 20
employees were setting up a scaffold to gain access and store material to work on a chimney. The scaffold was set up within 1
employees were setting up a scaffold to gain access and store material to work on a chimney. The scaffold was set up within 1
owner of company and employee #1 were installing metal roof decking for a warehouse building. Employee #1 was moving a w
tower erection contractor erecting a 250 feet high self supporting communications tower. Projection in final stages with one emp
operator was operating a mini excavator to break up loose stone. Operator was in process of pilling up more stone when the bu
on october 15, 1999 insde of santee cooper cros generating station at approx. 12:50 pm an employee collapsed and never rega
employee was attempting to locate fiber optic telephone cable across a 400 foot river which ranged in depth. Supervisors attem
a crew of 4 employees were in the process of lifting a catwalk up to a billboard approximately 40 feet high. One employee was o
A crew of three employees were removing an existing sidewalk with a backhoe, dump truck and a pavement breaker. The truck
Two employees were assigned to weld electrical lugs on the piping of a condensate recovery tank to install static lines. The line
Two employees were assigned to weld electrical lugs on the piping of a condensate recovery tank to install static lines. The line
Two employees were assigned to weld electrical lugs on the piping of a condensate recovery tank to install static lines. The line
Two employees were assigned to weld electrical lugs on the piping of a condensate recovery tank to install static lines. The line
Two employees were assigned to weld electrical lugs on the piping of a condensate recovery tank to install static lines. The line
Two employees were assigned to weld electrical lugs on the piping of a condensate recovery tank to install static lines. The line
Three employees were installing insulation under the residential house between the floor joists. One employee was lying on a s
Three employees were installing insulation under the residential house between the floor joists. One employee was lying on a s
A crew of 5 framers were standing up a framed stud wall at the gable end of a residence. The wall became too heavy for them
One employee cranked a utility truck and was attempting to back it off the roadway so the road could be prepared for paving. T
Deceased was on a ladder jack scaffold 9 feet 8 inches high framing an archway when he slipped, falling face down to a concre
Employee was cleaning up plywood, scaffold components, planking, etc. after dismantling a scaffold. The employee clipped wir
Employees were in the process of moving an antenna platform in place to be hoisted up a 185 foot transmission tower. The me
Employees were putting plastic covering over the work area to complete work for the day when the deceased backed into an op
The employee was making a delivery of mixed concrete to a residential site. He stopped his truck and began moving the pump
The employee was one of a 31 member crew performing maintenance on a paper mill recovery boiler during which time a chro
The deceased was on a column in preparaion to connect a beam. Another employee was positioning a manlit to connect the ot
The deceased was on a column in preparaion to connect a beam. Another employee was positioning a manlit to connect the ot
Employees were placing bundles of insulation on the roof of a building under construction with a Lull type forklift. The ground w
A crew of four (4) was assigned to change hardware on a new pole. One employee went up in the bucket without his gloves. W
Employees were installing metal siding on a building. The deceased was at 26 feet, 3 inches high level standing on a lower leve
Employees were using a crane to lift buckets of gravel into a trench to build up the bed prior to pouring concrete to expand a wa
Operator was loading a backhoe on a low-boy trailer 94 inches wide with the wheels of the backhoe 87 inches outside-to-outsid
A crew of six (6) employees were laying metal roofing panels over insulation that had previously been laid. One employee stepp
Employees were on two metal frame silo just starting to dismantle the silo. There was a walkway between the two silos. The de
Two employees were at the edge of an unguarded floor sixteen feet four inches above concrete when one employee slipped an
The employee was found outside residence where he had been installing a new phone line. A passerby noticed the employee o
Employee was on road crew involved with lengthening on/off ramps of interstate highway. Another contractor was doing the wo
Employee fell from a 17 feet 8 inch high porch to ground below. Employee was by himself and was apparently attempting to op
An operator and a helper were in the process of stowing a jib on the side of a crane boom. The process involved swinging the j
employee #1 was working in an excavation with varying depths of between 5 1/2 to 7 feet. He was replacing a broken section o
employee #1 was an equipment operator who delivered various pieces of equipment to construction sites. He was working alon
explosion and fire at pennzoil refinery. Three nps employees killed, two pennzoil employees.
explosion and fire at pennzoil refinery. Three nps employees killed, two pennzoil employees.
explosion and fire at pennzoil refinery. Three nps employees killed, two pennzoil employees.
investigation and coordination with coroner office determined the employee suffered a heart attack.
self employed individual hit overhead electric line with dump bed when dumping a load of dirt.
On November 23, 1998, at approximately 1:30 pm, employee #1 (crew leader), employee #2 (laborer) and employee #3 (labore
employee was tying rebar on a preassembled rebar mat that was held in place by a crane. The employee was moving vertically
y


                                                    Page 117
                                                         all


employee struck by truck and killed.
the victim was in the process of removing three sheets of plywood and temporary 2x10 floor joists in the second floor stairwell a
employee descending a 1,000 foot antenna via a two-point suspended scaffold encountered a malfunction which resulted in the
on 7-20-98 an employee of bancroft contracting corporation, was electrcuted while welding at the mead paper company in rumf
The employee was working on the 2nd floor working area with out fall protection. He was working on the exterior side of the bui
The sole proprietor of Jones Painting Company was electrocuted while he assisted his only employee in raising an aluminum e
An employee was crushed between the dump body and the truck frame of a dump truck. The employee was performing mainte
Employee landing a load that was suspended from a crane was electrocuted when the the main cable of the crane came into c
the deceased was an independent truck driver delivering stone to an excavation contractor (iron horse, inc.), which was building
the deceased was working on the second floor of a house under construction. Two heaters were operating on the first floor whi
deceased employee was discovered in the basement of aforementioned site location, lying face down in a pool of blood. There
Employees were installing roof trusses on a two story addition to a church. When one roof truss fell over striking the truss next
Employees were installing roof trusses on a two story addition to a church. When one roof truss fell over striking the truss next
employee no. 1 removed the lower locking pins that connected two 20 foot sections of lattice boom, while he was positioned un
employee was operating a 1975 caterpillar d8k bulldozer in site clearing and grading project when a worn and abraded hydrauli
vanceburg readymix, inc. - sic: 3273 on october 2, 1998 at approximately 2:30 pm, employee #1 was assisting another worker w
mobile crane made contact with 7200 volt overhead power line, causing the electrocution of a employee who was signaling and
Employee was standing on the bumper of a moving full size cargo van. He was holding on to a ladder rack which was attached
on august 29, 1996 at approximately 4:45pm the owner of florida welding and the deceased were sliding a roof curb in place wh
two employees were working inside a trench approximately 14 feet deep. They were inside a trench box that was 8 feet in heigh
a journeyman electrician fell off of a 12 foot step ladder while wiring in new lighting at a new methionine plant under constructio
on 03/18/97 an employee was in the excavation boring an 18 inch casting for a water line, when he was trapped by the spoil pa
electrocution. One employee died and two others received serious injuries resulting in permanent disabilities when they were rig
electrocution. One employee died and two others received serious injuries resulting in permanent disabilities when they were rig
electrocution. One employee died and two others received serious injuries resulting in permanent disabilities when they were rig
the deceased was pulling the back off of a roll of adhesive water proofing when he backed off the edge of the roof.
three employes wer laying a french drain at a privat residence. They had excavated unde rthe house a depth of approximately 7
employees were engaged in steel erection, placing metal decking on the roof of a steel building. The employee fell approximate
the deceased was climbing down a radio communications tower when he fell approximately 100 feet.
two employees working in a trench exited a trench box to retrieve some hand tools when the trench wall collapsed on them. On
an employee was crushed to death when a ramp from a low boy truck free fell. The employee was standing too close to the rais
r & m plumbing company is a general plumbing contractor which was installing sewer and water lines for a new construction ca
bill bradley plumbing, heating and air-conditioning company consisted of two divisions, service and construction, totalling appro
bill bradley plumbing, heating and air-conditioning company consisted of two divisions, service and construction, totalling appro
one employee working on the ground was electrocuted and another one suffered from electrical burns when a crane came in co
the employer, cardinal contracting, inc., is a construction contractor employing 25 employees that do maintenance and utility wo
employee was taking the slack out of a power line that had been moved from an old pole to a new pole. The employee was wor
the company was preparing to set up operations alongside a rural highway to bore under the highway in preparation to install a
on 1/26/99, the victim, Ard Contracting, inc. employee fell 17' from the third tier of tubular welded frame scaffolds. The victim w
on 03/04/99 the weather was clear and dry with no unusual or adverse weather conditions at the time of the accident. While wo
an employee was fatally injured when he fell from a ladder jack scaffold. Fall distance of approximately 8 feet.
employee was fatally injured when a load of pile driving pipes that was being lifted with a crawler crane, swung and crushed his
the employee/deceased was found laying at the foot of a stairway. No one witnessed the accident.
Three employees were working on a low-slop roof with an eave to ground distance of approximately 20 feet. Employees were c
on the day of the accident the owner of the company and two laborers were setting up a mobile home on concrete block piers.
employee/owner was fatally injured when he contacted a 277 volt energized power line.
at the time of the accident the weather was clear and dry with no unusual or adverse weather conditions at the time of the accid
1. An employee was fatally injured when he was thrown from a bull dozer and ran over by it. The deceased was not wearing se
Employee complained of chest pains. Employee's blood pressure was taken by the safety officer and it was very high. Employe
An apprentice electrician using insulated cable cutters was fatally injured while removing (cutting) deenergized conductors from
On 4/3/00 at approximately 11:30 AM, the victim fell to his death from a third floor exterior balcony of a single family residence w
On 7/21/00 at approximately 10:49 AM a 22 year old laborer was fatally injured when he was struck by a Caterpillar 12G motor


                                                     Page 118
                                                         all


The owner/employee was operating a conventional boring machine installing steel casings underneath Interstate 10 for installa
Employee was part of a 6 person team dismantling a tube and coupler scaffold inside of a paper mill digester. Employee was fa
An employee was fatally injured while power washing from a ladder.
A 14 employee/roofer removing built up roofing fell though an unguarded skylight.
The accident was the result of an impaired driver crossing into a properly marked construction zone and striking an asphalt spr
an employee of T.C. Broome Construction Co., Inc., was fatally injured when his head and neck became pinned between an ov
the operator of the dump truck became trapped by the metal bar that is attached to the body of the dump truck. The metal bar i
employee contacted 7900 volt electric line with aluminum extension ladder
employee fell from a roof
one employee who was in the process of installing a section of new rubber roofing material, and was working at the edge of the
the owner of this company fell from the roof of a rtesidential house, while striupping asphalt shingles with a pitchfork. He fell 33
a pile driver was struck in the head by a wooden pile. A pile driver was in a 15 foot deep pit spotting 50 foot wooden piles when
the owner of this company was moving a 32 foot aluminum extension ladder in near proximity to overhead electric power lines c
an employee of erection specialist was run over by a cat 235 excavator operated by anchor excavating.
an emplyee was electrocuted and another employee was seriously injured while dismantling and lowering an aluminum pump ja
an emplyee was electrocuted and another employee was seriously injured while dismantling and lowering an aluminum pump ja
the owner of christopher crosby builder, the general contractor building the single family house, died after falling through a seco
a male worker, son of the owner of the company, died after being removed from a 9 foot deep unprotected sewer trench that co
employee had a heart attack on his way to work
balco, inc. employee was repairing a walk-in freezer at a restaurant, dick's last resort, 55 huntington avenue, boston, saturday
the self employed welder, attempting to seal some leaks in the 19.5 x 13 inch rim wheel with the tire mounted on the rim and th
apparent heart attack
Shortly after 1:30 PM on 04/25/00 the driver of a gunite truck pulled into the breakdown lane on Interstate 95 north bound lane,
The employee was returning from lunch and was inside of the construction zone, when he was caught between a jersey barrier
The employee was conducting a welding operation on the nineteenth floor when he lost his balance and fell from the steel and
Laborers were working in an excavation while a backhoe was operated at grade level. The backhoe was supplying gravel with t
An employee fell approximately 40' from a tubular welded frame scaffold to the ground below where the work platform was not
The employee was found unconcious on the ground near a felled extension ladder. It is unclear at this time if the employee fell
An employee was climbing down a ladder into a 14 foot deep excavation when the rubble wall of the excavation collapsed. The
on 11/2/95, at approximately 1300 hours, an ironworker, who was setting bridging on bar joists, fell approximately 27 feet from
on february 3, 1997, at 11.15am. A carpenter was framing a exterior wall when he fell off the edge of the 1st floor of a townhom
victim installing rain gutter, fell 13 feet from scaffold.
november 21, 1997. Approximately 11:15. Victim is crushed by contact with a d5 dozer while presumably checking the grade. H
one employee fatally injured when the scissor lift he was working on was pushed over by a opening overhead door. Employee f
on 1-22-98, at approximately 1410 hours, an employee attempted to lower an elevated platform attached to the forks of a forklif
on 03-12-98, at approximately 4:45 p.m., an employee was desending a 40 foot aluminum extension ladder that was extended
on 11-02-98, at approximately 1253 hours, employees were transporting a mat grid made of reinforcing steel rods. The mats w
the employee fell 44 feet while connecting sheet metal ducting.
employee was working beneath a bridge from a lift truck bucket running electrical conduit to a changeable message sign. The l
crushed by dump truck.
employee was crushed by a goose-neck trailer
Employee straddling the front and side rail of a truck dump box fell backwards onto a concrete curb. The approximate 8 1/12 fo
Victim was prepping a work bay by pressure washing when the aerial lift platform that he was using came into contact with an I-
Victim was installing hurrican clips on roof trusses. He was working alone standing on a ladder off of the floor level. To install th
The victim was removing steel boiler pipe during a demolition project. The victim was working on the 3rd floor removing the ma
on 09/30/96 employee #1 was installing roof trusses on a new building that measured 66 feet wide and 80 feet long. Employee
on 09/30/96 employee #1 was installing roof trusses on a new building that measured 66 feet wide and 80 feet long. Employee
the employee was a sheetmetal installer patching holes around ductwork in the attic area of the building being remodelled. He s
employee 22 yrs old, died 5/14/97 at 5:05 p.m. when a trench caved in.
employee, 21 yrs. old, was electrocuted and died 7/6/97 at 9:30 p.m.
employee parked his tractor trailer parallel to the highway. Another employee was side loading a cat from end loader on the trai
employee was electrocuted when he touched a steel beam that had come in contact with an electrical wire.


                                                      Page 119
                                                        all


on 08-11-98 at approx. 2:25 pm, an electrical contractor employee was installing a quantum model elm2 277 v input emergency
employee was working on a sunroom. Working on a light switch circuit changing a wire. Found by the home owner electrocuted
employee #1 was working off an unsecured 28 feet extension ladder. The employees had rested the top of the ladder on the wi
cherokee county maintenance & engineering. - sic: 1611 on 4/29/99, at approximately 8:15 am, employees were working at a b
employee dies from sever heat stress.
employee was standing on the ground holding a ground or static wire which was supposed to be dead. Employee received a sh
dump truck body dropped crushing employee.
Crane cable went into an overhead power line. Employee was electrocuted.
Journeyman lineman preparing to remove a paralleled pole mount 7200/240 volt transformer from an utility pole. The lineman r
Employer was moving a house on a county road. Employer asked employee to get out of truck and check safety lines. Employe
Deceased was a partner for the company who died from trauma to head and/or broken neck when the scaffolding he was on fe
Two brothers accidently made contact with live electrical wires while shingling a house. Both were transported to Mercy Medica
The employee was working on the water tower guiding the thank to the tower legs when the crane collapsed.
Employee working at construction site went to use the bathroom in the basement. Employee slipped and fell down the stairs.
Employee #1 was bent over at the waist taking tools out of a 5 gallon bucket which was located on the passenger side of a Keif
Employee #1 was on the back side of the house, cutting up damaged gutters to be hauled off the job site. As employee #1 took
an employee fell either while getting on or from a flatbed truck. The truck was parked. The employee died from severe head an
on 3/10/96 at approximately 1:12 pm the 6 foot tall 240 lb. 31 year old carpenter's helper was standing on the 4th step from the
the worker was removing a guardrail to install a annealing furnace. When the corner post was removed there was enough tnes
an employee was involved in a project to remove old crane rails and install new rails. The employee was not tied off. A section
on 02/13/97, a trench approximately 10' in depth caved in.
on may 23,1997 an operator of a caterpillar track dozer d6h, was fatally injured when the dozer struck the operator pulling the o
on june 10th 1997 at approximately 11:25 am an employee was directing off road traffic at a cement mixing batch plant. The em
employee struck a 7.5 kv overhead line with a derrick
on 09-17-97 at approximately 3:05 pm two employees were winding down a work day the two employees had been conducting
an employee was carrying an aluminum ladder on a roof. The ladder came in contact with energized 25 kv lines.
employee was killed when a double walled steel tank failed after air pressure was applied to the shell space in order to perform
an employee fell 25'6" from a roof.
on 1/18/99 two employees were preparing to remove a roof from a residential home. One employee was sitting on the roofs pe
three workers one, in an aerial lift and two others were setting steel roof trusses and connecting the bridging. When they finishe
employee fell 25 feet from a steep pitched rof
employee was clearing land for the mon valley expreesway. Employee was moving a piece of equipment over a grade when the
on december 01,1999 an operator of a 50 ton caterpillar truck and the operator of a caterpillar road grader were attempting to u
The deceased was working in an underground tunnel that connects a boiler/chiller plant to the hospital. The employees were te
fall from elevation
off highway vehicular accident
An employee was run over by a truck, parked on a grade, because the wheels were not proerly chocked.
employee was electrocuted
employee was electrocuted
Employees of a scaffolding company were building a scaffold inside of the combustion chamber of a fludized bed boiler. The bo
Employees of a scaffolding company were building a scaffold inside of the combustion chamber of a fludized bed boiler. The bo
Employees of a scaffolding company were building a scaffold inside of the combustion chamber of a fludized bed boiler. The bo
Employees of a scaffolding company were building a scaffold inside of the combustion chamber of a fludized bed boiler. The bo
Employees of a scaffolding company were building a scaffold inside of the combustion chamber of a fludized bed boiler. The bo
A contractor had received a truck load of rebar for bridge construction project. A Laborer was crushed between the back of the
An employee was struck and fatality injured when a concrete slab toppled and struck the employee while the 5Ft.X 5Ft X 12 inc
A contractor was putting the top on one of two 35,0000 gallon steel bolted water tanks, each 16 feet high and 18 feet in diamete
an employee was working at the 20' level re-positioning some steel bar joist when 3 of the joists twisted and fell to the concrete
a steel errector was at the 62' level waiting to accept a steel module to be connected to the existing structure. The "h" shaped m
the wordperfect files are cleaned periodically. That is why there is not abstract here.
an 18 year old employee, mexican national, was performing his duties on a mast-climbing work platform appproximately 30 fee
employee no. 1 was installing the ridge cap on a metal roof of a metal building that had been completely decked except for the


                                                    Page 120
                                                         all


employees were involved in removing old concrete and set a new footer for some additional machinery. The deceased had just
employee #1, equipment operator, was operating a front end loader, traveling east down a dirt roadway adjacent to a borrow pi
An employee age 36, a dumper/spotter in an asphalt road construction crew was killed when the bed of a dump truck contacted
on october 06, 1998, a 52-year-old male superintendent died when he fell from an unguarded roof to a metal floor approximate
A laborer, was engaged in installing an asphalt overlay on an existing road. He was using a gasoline powred air blower to clean
FATALITY INVESTIGATION NARRATIVE: At approximately 0900 hrs on 22 Aug 98, the electrical wiring/components within the
at approx. 6:15 pm on 1-21-99, the deceased employee was working as a swamper at a gas pipeline construction off airline hw
on 1-30-99 the deceased employee was operating a traverse forklift tractor (model tl6035; serial number 60653-ccc) at a const
on january 19, 1999, a 52-year-old male, employed as a lineman, with 21-years of lineman experience was fatally injured when
on 9/21/99, jimmy mcbroom mobile home movers was in the process of hitching a 14 foot by 60 foot mobile home to a truck. Th
On March 5, 1999 at approx. 1035am at the Mallard Junction elevated water tower located on Grogran St. Lake Charles, LA an
A hydroblaster, received a wound to his left arm when he failed to disengage the pressure to the unit prior to moving the wand t
employee apparently fell to his death 11 feet into a sump pit.
at approx. 2 pm on 6-8-99 the deceased employee was on the 5th level of the lsu life science bldg under construction. He was
fatality investigation narrative: on the afternoon of 3 feb 99, the employer was in the process of completing steel erection functio
the employee was working on a pile driving barge on the mississippi river. The employee was told to put up a ladder and go get
on january 16, 1999, five employees of irby construction company were doing work for entergy, an electric utility. The job at han
deceased employee was working with two other employees at the baton rouge north landfill off us hwy 61 on 6-28-99. Shortly b
FATALITY INVESTIGATION NARRATIVE: The employer, was one of the sub-contractors under the control of Circle, Inc, the g
FATALITY INVESTIGATION NARRATIVE: The employer, was one of the sub-contractors under the control of Circle, Inc, the g
FATALITY INVESTIGATION NARRATIVE: The employer, was one of the sub-contractors under the control of Circle, Inc, the g
FATALITY INVESTIGATION NARRATIVE: The employer, was one of the sub-contractors under the control of Circle, Inc, the g
FATALITY INVESTIGATION NARRATIVE: The employer, was one of the sub-contractors under the control of Circle, Inc, the g
on april 14, 1999, credentials were presented to the owner of Pitch Perfect Framing, at the opening of investigation of allegation
this 37 year old white male reportedly was hanging siding on a house when he suddenly collapsed falling off of a two ladder. An
the crew had errected the main tower and a crossbeam antenna on 10/2/99. Two employees were on the crossbeam dressing
the crew had errected the main tower and a crossbeam antenna on 10/2/99. Two employees were on the crossbeam dressing
the employee was up in the crawl space of the montgomery wards store located at 1700 ne evageline thruway, lafayette, la. Th
An employee of Thibodaux was working on the air conditioning when he fell 35 feet from the ceiling of the civic center to the se
a crew was laying sewer pipes. The trench had been dug and the trench box pulled into place. The boards and protector cloth h
on 11/25/99, the victim and a co-worker had taken a 14' aluminum skiff out about 250' from the dredge barge for the purpose o
A four man crew was assigned to perform maintenance, repair, and replacement of numerous pad mounted transformers in an
On the morning of 2-16-2000 at approx. 8:15am the deceased employee was working with a company crew installing new fiber
On 01-25-01 the deceased was working as the foreman of a utility crew replacing an old pole when he was eledtrocuted. The d
An employee performing flagperson duties at a construction site on a two lane highway (Hwy 190) in the town of Crowley, La., w
On October 5, 1999, a contract helper was assisting a second contract company in replacing I- beams in the barge slip of the h
A roofer, retrofitting a new metal roof at the D.G. Hunter Power Plant, located 1011 N. 3rd. st., Alexanderia, La.fell through a ho
Employee #1, a mechanic who worked for a heavy equipment leasing company and another mechanic who works for a differen
On Aug 10, 2000, employee #1 was working with a crew along Hwy 17, Warden. La. installing a 54" diameter by 8' long concre
On 2/23/00 a crew of 5 was in the process of pulling three new conductor cables to replace three existing cables in Cubicle #36
On the afternoon of 11-1-2000 the deceased employee was working with a roofing crew at a shopping center under constructio
Nelson Service Company was contracted by Alcoa Primary Metals to insulate sucts coming off coke cooler hoods. A scaffold w
On the morning of 12-8-2000 the deceased employee was working with a crew doing structural steel work at a church building
FATALITY/INCIDENT/ACCIDENT INVESTIGATION NARRATIVE: At approximately 1600 hrs on 18 Dec 00, an employee ( age
On March 9, 2001 at approximately 6:00 pm, employee #1 was attempting to walk across 3 sets of railroad tracks (total distanc
Employee No. 1 was working on the roof of a metal building - an abandoned car dealership - when he stepped through a skylig
On April 14, 2001 at approximately 08:30am, employee #1 was working from the first floor landing performing the job task of cu
On 6-26-2001 the employees of Diversicom, Inc were in the process of erecting a telecommunication cellular tower, they workin
employee was working on an unguarded scaffold plank approx. 17' above the floor when he fell onto the floor. He struck his he
employee was carrying "x" braces for steel bar joists . while walking across the top of bar joists, employee fell twenty sis (26) fe
on february 20, 1997 at approximately 5:15 pm employee number 1,and a helper working at a private residence an installing a r
mobile crane boom crimped/bent/fell landed on superstructure where employees were dismantling stacks. Employee was hit by


                                                     Page 121
                                                          all


employee number 1 was performing a drilling operation with a cme-45c type drilling rig, on a slope of about 20 degrees on rock
the sole proprietor cut a stairway floor hole in the sub floor. After moving the particle board, the employee stepped on the board
the employees was working on the paving crew and bent down next to the dump truck. While bent down the bobcat backed up
an employee fell approximately 16 ft. from a roof while attempting to place a cover over a firewall. No fall protection was used.
An employee from a roofing contractor was lifting metal decking with nylon slings. One of the slings failed, allowing the load to d
On March 3, 2001, at approximately 9:15 a.m., an employee was injured (fatality) when an inadequately sloped trench caved-in
Two (2) employees were in a seven to eight foot deep trench with vertical walls and no protection installing a sewer lateral from
el empleado se disponia a vaciar un canasto de cemento que pendia de una grua que lo transportaba. La grua se acerca a un
victim was removing wood forms from a concrete curb that had pour the day before. The head of a form nail he was pulling bro
painter was working on a scissor lift at about 25 feet(7.6m) elevation when he fell to the concrete floor below.
employee, part of crew dismantling scaffold, fell approximately 27 feet. Witness stated that scaffold frame member caught emp
employee was struck by falling metal pipe. Chest and leg injuries.
on 11/21/97, an employee whose normal job is to roof and reroof buildings, was given the job of dismantling the roof of a metal
victim was part of a crew running a rope across railroad tracks to be attached to a fiberoptic cable. A train came down the track
employee working outside protection of trench box was crushed by approximately 15 tons of limestone rock that sheared off ins
see form #36.
victim was wiring the line side of the main breaker while energized. He had connected one of the three wires and was electricut
employee working from uninsulated boom truck bucket was throwing a plastic and fiberglass rope with lead weight attached ove
hvac employee preparing to install air conditioner on roof of 2-story building was electrocuted when he struck 7200v primary ele
victim was operating a backhoe when the ins raided the jobsite. He jumped off of the bachhoe to hide in a pile of concrete caps
flagman was backed over by a dump truck while he was taking to a motorest.
an employee of h. chapman pipeline construction, inc. got out of the excavator he was operating and was bent over, marking h
an employee was rolling out insulation for a metal roof deck under construction. He stepped on an an unsecured end of a walki
mason was working off of a six foot scaffold when he fell backwards to the concrete driveway below.
an employee who was carrying cabinets up to a third floor apartment under remodeling, stepped backwards off an ungurded sta
victim was throwing steel scrap down a hole when he fell in the hole 60 feet (18m) to his death.
employee was connecting steel, when he fell 15' from metal beam.
employee fell 17 feet 2 inches through a tar paper covered skylight opening at a residential construction site. He received fatal h
eighteen-wheel truck was backing up and ran employee over. Employee was standing behind the trailer at the blind spot.
employee was working on a two man crew installing telephone line in an attic of a private residence, remodeling the inside of th
a three man crew was excavating a five foot deep trench. One employee operated a backhoe; one employee operated a track h
a tower technician was renovating antenna elements and replacing o rings on a 1230 foot radio transmission tower. His assista
an employee was killed in a trench while trying to adjust a sleeve on a pipe.
victim was installing fiber optic cable in universal city. The two man crew was using a truck equiped with a bucket and boom. Th
employee fell from vehicle while riding on bed of truck.
victim was painting sealer onto the joints of air conduit while standing about half way up a 10 foot (3 m) stepladder. He lost his b
An electrician was checking wiring and circuits in a J-box, when he grabbed a hot 480-volt line and was electrocuted. The elect
victim was drilling holes to set electric poles when he drilled into a lpg pipeline. He died in the large explosion that resulted when
during installation of 5600 lb storm drain pipe, employees were permitted to work in and adjacent to trench as load was lifted ov
worker was part of a crew removing oak trees from a highway construction site when he was struck in the head by a branch wh
employee electrocuted while replacing ballast on live 277v fluorescent light fixture.
employee was caught between flatbed trailer and crane superstructure when the crane turned over.
AN EMPLOYEE WAS DRIVING A PS180 CATERPILLAR ASPHALT ROLLER TO THE COMPANY'S STAGING AREA AND W
Employee working on a madeshift scafold was hit by a hip rafter lost his balance and fell 32 ft.
Employee working in a trench got his head decapited by the bucket of an excavator,
Employee was erecting steel in project building when structure fell down on employee.
Victim was painting the inside of a 110 foot (33.5m) water tank when the rigging holding the boatswain chair came loose. He wa
AN EMPLOYEE FELL FROM A SECOND FLOOR PATIO WHILE ATTEMPTING TO INSTALL SHEETROCK TO THE CEILING
Roller/Compactor was hit by an 18-Wheeler killing employee driving roller.
Employee connecting steel truss fell to his death when the structured collasped.
Victim was removing the ceiling tile when he came in contact with a 277 vac lighting circuit.
Employee painting overhead slipped on uneven platform created by one plank being above adjacent platform and one plant bel


                                                      Page 122
                                                         all


Narrative for Fatality Inspection Three employees were supervising the pouring of concrete into a steel mold, in order to constru
Narrative for Fatality Inspection Three employees were supervising the pouring of concrete into a steel mold, in order to constru
Narrative for Fatality Inspection Three employees were supervising the pouring of concrete into a steel mold, in order to constru
An employee was crushed when he dismounted a forklift and the load he had been transporting fell sideways off the forks and
An employee was found suspended from a lanyard that was attached to the bridging of the south Gym.
An Employee fell from a ladder onto an asphalt ground
An employee was walking on a stack of decking positioned between some steel beams, when he reach the end of the stack, fe
Victim was involved in an altercation with another ee. The other employee chased the victim to an unfinished roof and pushed h
AN EMPLOYEE WAS THROWN FROM AN AERIAL LIFT WHEN THE AERIAL LIFT HE WAS OPERATING WAS STRUCK B
Interstate treating company had a contract with Cross Timbers Oil Co. to pressure test a 5000 gallon separater tank. A water tr
AN EMPLOYEE FELL FROM A GIRDER WHILE WELDING.
Victim was working on a hydraulic lift cleaning exterior walls when he came in contact with power lines and was electrocuted.
Welder stepped on steel web joist as he was moving to a new location. The joist was not welded and rolled out from under him
AN EMPLOYEE WAS CRUSHED BETWEEN A EXCAVATOR BUCKET AND 90 FOOT STEEL BEAM END DURING THE RIG
AN EE WAS REFINISHING A RESIDENTIAL TUB WHEN HE WAS OVERCOME BY FUMES CAUSING HIM TO LOSE CONS
The employee was working in a damp excavation. The employee had a electrical Sump pump, Florescent Lamp and an extens
An employee was attempting to repair an High Voltage Distribution Line when he came into contact with the grounding conduct
workers were taking down an aluminum pole to a pump jack scaffold system and accidentally contacted an overhead electrical
employee had set ladder against power pole and was installing new drop from pole to service meter. While feeding new service
employee was trying to remove a steel bar that was inserted vertically between the raised dump truck body and frame of the du
Narrative / Description - Interviews, written statements, accident report and on-site evaluation On 10/12/98 at approximately 17
the deceased was installing a metal roof on a building that was about 20' high to the eaves, 40' wide and 80 feet long. The build
at about 1:20 pm, 06/29/1999, the victim ( 29 years old) was operating a rough terrain forklift (gehl telescoping boom forklift, dy
a catv crew were installing a cable and the worker in the aerial lift basket accidentally contacted an overhead electrical line and
the victim (employee of glen builders inc.) sustained fatal injury when he was struck and backed over by a mack truck (operated
PRELIMINARY: The company was erecting custom cut rafters over the newly added second floor of a residence. There were 5
While installing Grove GMK 5120 lattice boom jib to the main boom the jib fell from the crane and fatally crushed an employee.
fall due to collapse of walkboard--impalement on metal bracket
on may 20, 1996, at approximately 7:30 p.m., employee #1 was monitoring the placement of felt on the roof of an existing build
broom sweeper crash due to brake disrepair.
electrocution while working on "hot" wire.
employee was sent to private residence to make a service call involving a central heating and air conditioning system. When th
employee was in an 8-foot deep trench digging a water line. Ditch collapsed and the employee died later as a result of injuries s
on 4/15/98 at approximately 10:00am employees #1 and #2 along with one other employee were attempting to dump concrete
on 4/15/98 at approximately 10:00am employees #1 and #2 along with one other employee were attempting to dump concrete
employee slipped and fell 15 feet to a concrete floor.
a journeyman electrician was killed when electrocuted by overhead high voltage wires while installing a light pole. The victim wa
three men were in the process of a demolition job of concrete and steel structure using a bulldozer inside the building to knock
employee #1 fell through a roof opening approx. 4'x4'. He fell approximately 15'. The employee was installing a built up roof.
on 5/20/98 at approximately 10:00 a.m. employee #1 was moving an 26' aluminum extension ladder when it came in contact wi
three employees were working off an overhead bridge crane when the cab operator contacted the three phase 460v runway line
on dec. 10, 1998 at approximately 8:00 am, an employee was preparing to load a cat bulldozier on a lowboy trailer. He backed
on march 12, 1999 three workers were on a telecommunications tower located in dickson, tn. They worked for irby construction
three workers were working around/making repairs (welding) on a crude oil storage tank. Approximately 90 gallons of crude oil
three workers were working around/making repairs (welding) on a crude oil storage tank. Approximately 90 gallons of crude oil
three workers were working around/making repairs (welding) on a crude oil storage tank. Approximately 90 gallons of crude oil
employee no. 1 was inside the base of a trench which had an overall height of approximately 10 feet. The sidewalls of the trenc
employee attempted to cross interstate 40 traffic to get to vehical parked in the median and was struck by a moving vehicle.
on december 17, 1999, at approximately 2:50 p.m., employee #1 was pulling a 40 foot aluminum extension ladder away from th
On 01/11/00 an employee of All Pro Painting was working at Saturn of Spring Hill. His responsibilities were to paint the exposed
An employee was struck by a backhoe bucket while installing and back filling a sewer line. He was using a front end loader to b
employee was welding washers to secure the metal decking around a pit opening. The employee finished the welding operation


                                                     Page 123
                                                         all


employee working out of an aerial lift overturned. The lift was provided with 4 outriggers but they were not deployed.
an employee was electrocuted while working on or in a substation at becromal of america, inc. he was not an employee of trade
employee struck by lightning while operating a front end loader. He was getting off the equipment when he was killed.
a fatality occurred.
An employee age 26 died.
an employee, age 27, died while a brace from a gabled end of one wall fell inward into the structure striking him resulting in a fa
employee working at an elevation of 28 feet above the next level. The employee was making a double connection and was rem
An employee, 26, was knocked down to the ground by a 1 ton flatbed and rear passenger side dual tires ran over his head.
A horizontal (directional) boring machine was being used in the underground placement of fiber optic conduit, under a roadway.
Employee was working on scaffold platform with no guardrails or other fall protection. Employee interviews suggest that the wo
Two employees were in the process of laying 8" pipe in a 9' deep x 9' wide x 38' long excavation. The employer had classified t
Two employees were in the process of laying 8" pipe in a 9' deep x 9' wide x 38' long excavation. The employer had classified t
On September 6, 2000, at approximately 1:40 pm, employee #1 was performing a drilling operation in order to prepare the rock
It is assumed that the employee fell from the sixth guest level of a hotel under construction. It is not known what tasks the victim
A crew of men on a bridge site were moving steel needle beams from beneath the bridge when the tip of the boom on the boom
Owner (employee No. 1) was using a ladder attached to a rope secured to a porch column. The rope extgended from porch ove
Work involved dismantling metal buildings, more specifically the corrugated roofing at the time of the accident. While standing o
Victim was tightening a splice flange, started to reposition himself when he fell 60 ft. Asecond employee was up on the tower w
On March 8, 2001 at approximately 2:30 p.m., employee was installing roofing and insulation without any fall protection. The tin
Four workers were removing a 3/4-inch thick masonry / plaster layer from the face of a 16- foot tall by 76-foot long masonry bric
Four workers were removing a 3/4-inch thick masonry / plaster layer from the face of a 16- foot tall by 76-foot long masonry bric
Four workers were removing a 3/4-inch thick masonry / plaster layer from the face of a 16- foot tall by 76-foot long masonry bric
Four workers were removing a 3/4-inch thick masonry / plaster layer from the face of a 16- foot tall by 76-foot long masonry bric
Employee was checking out power to AC/Heating system, went from inside panel to outside where meter and disconnect was l
Employee was on steel beam being removed from bridge, stepped off beam onto a 6 ft. steel diaphragm that had been cut on b
an employee 22 years old, fell approximately 25 feet from roof onto concrete below resulting in death. The accident happened a
An employee was at the site delivering payroll checks to employees his company was providing. South block wall on entry wall
Employees #1 and #2 were abrasive blasting from separate man lifts inside a hydropillar water tank when employee #2 heard a
Employee fell from a walkway on sequence batch reactor (SBR) tank, a height of approximately 24'. A safety cable had been in
Employee fell from top of cooling unit approx. 9' onto guardrail on roof. The employee was installing insulation on duct. He rece
Employee #1 was using his personal farm tractor equipped with a bush hog to clear vegetation growth on lot under construction
Employee was on edge of flat roof installing U-shaped metal coping material on the edge of the roof when he fell from the roof,
Employee #1 and employee #2 were in the process of attaching a materials basket to the working line of a truck crane. The truc
An employee was in a trench 6 feet deep, 68" wide setting a concrete pipe 7 & 1/2 feet long. The back hoe operator had to lift th
The job being performed was a sewer re-line project. A liner is placed in the existing sewer pipe by elevating a portion of the lin
Employee No. 1 working alone attempted to load a 13 foot long 8 inch sewer pipe onto a backhoe. The employee either droppe
employees used 80 ponds of air pressure to test the return chilled water line for leaks. The line was equipped with multi purpos
employees used 80 ponds of air pressure to test the return chilled water line for leaks. The line was equipped with multi purpos
employee was working ten feet above ground level helping to set and brace trusses that were being erected. Employee was na
employees working on demolition of bridge by removing sections of bridge. After removing supporting members, remaining me
employees working on demolition of bridge by removing sections of bridge. After removing supporting members, remaining me
employees working on demolition of bridge by removing sections of bridge. After removing supporting members, remaining me
employee was involved in moving 3/4 inch thin wall conduit that had energized circuits running through it. The conduit had to m
an employee had been working his first day of employment on a roof doing cleanup activities while other employees were insta
an employee was working on a demolition operation where by a load out facility was being dismantled fell from the first level ap
Employee raised dump bed to inspect wiring for a brake light. The employee did not have anything to brace up the bed and it fe
Operator of the Cat D8K Dozer was run over by his own machine.
An employee was flagging traffic on route 52 south for construction vehicles that was crossing the road. He had a car stopped w
Fell from ladder
after severe thunder storms and winds in excess of 70 mph a line construction crew was called out to repair downed power line
the four lane turnpike was reduced to the inside eastbound lane due to construction. Vehicle 1, travelling in excess of the poste
october 15,1998, 4:23 pm, a seven man crew was engaged in the mobile operation of stripping the center of a repaved 2 lane s


                                                     Page 124
                                                         all


employee #1 and employee #2 were attempting to remove the manhole cover from an underground 8,000 gallon gasoline tank.
employee #1 and employee #2 were attempting to remove the manhole cover from an underground 8,000 gallon gasoline tank.
employee #1 and #2 worked for a contractor providing facility maintenance and construction support at a petrochemical researc
employee #1 and #2 worked for a contractor providing facility maintenance and construction support at a petrochemical researc
Date of Accident: September 17, 1998Approximately 11:40 AM Employer and employee were working on a roadside billboard l
employees were loading pipe onto a flatbed trailer, employee # 1 was on the trailer and standing between a pipe that had just ro
the ironworkers were installing a sheet metal roof on the structure under construction. They were positioning and securing shee
employees were installing metal roofing deck 25 feet above floor level without fall protection when employee #1 fell off the leadi
employee #1 (company owner) along with another worker was in the process of blocking and leveling a 23,000 pound mobil ho
at the time of the accident employees #1 & 2 were attempting to attach a crane sling to a concrete form for the purpose of remo
at the time of the accident employees #1 & 2 were attempting to attach a crane sling to a concrete form for the purpose of remo
employee 1 was to inspect a masonry chimmey flue for cracks on the second story of a residence, the roof surfaces were damp
employee #1 was controlling traffic on one end of a highway overpaving project as a flagperson. Employee #1 had just move hi
on 07-10-98 at 3:00 pm, three masonry employees on a frabricated frame scaffold were concluding the days work of grouting th
employee #1, a laborer, and a backhoe operator were assigned to add an extension to an existing drain pipe. The drain pipe ra
employee #1 was installing an antenna mount on the top of a 300 ft. telecommunications tower along with another employee. B
victim #1 was in the process of welding a gusset in place for a fan support. He was in the plenum chamber of a wood drying kiln
12-31-98, two employees were engaged in tightening diaphragm bolts on an elevated highway bridge girder. Employees were u
march 30, 1999. At 7:30 am a three man crew began the installation of some 24 new skylights on a one story (high) renovated
the concrete construction crew was in the final stages of a project of removing and replacing various sections of concrete curb
on april 28, 1999, at approximately 3:00 p.m. employee #1 was hanging sheet rock while standing on a 6 foot high perry mobile
08-12-99 at 01:45 pm a crew of about 24 employees were finishing the day's job of installing insulation on a roof deck of a 31 fo
fall from elevation, platform attached to forks of a rough terrain forklift, impact on concrete sidewalk. Fall was fro approximately
on november 23, 1999, employee #1 and employee #2 were in the process of laying asphalt for a crossover in the median of a
on november 23, 1999, employee #1 and employee #2 were in the process of laying asphalt for a crossover in the median of a
employee #1 was working to install metal roofing at a height of approximately 18 ft. above ground level when he fell through the
august 31st 1999. Three man crew finishing construction of new outdoor advertising sign. Employee was dismounting billboard
Refer to: Investigation Report CPL 2.113 attached. On June 8, 2000, at approximately 8:00 am, employee #1 was working on a
June 08, 2000. Approximately 2:40 PM. A crew of four were on a company barge returning to dock. The crew intended to obtain
Four workers working under or near a spiral conveyor machine being held up by four jack, no cribbing or other means to secure
July 31, 2000. At approximately 1:45 PM a crew of 4 steel workers were installing a center solid web rafter weighing approxima
On August 21, 2000, at approx. 9:00 am employees were in the process of changing out an electrical wooden power pole. The
On August 21, 2000, at approx. 9:00 am employees were in the process of changing out an electrical wooden power pole. The
September 26, 2000, At approximately 8:30 AM three welders were removing 8 foot sections of a bridge I-beam that had been
Abstract attached.
January 3, 2001. An apprentice lineman was assigned to work with an electrical coop engineer trouble shooting electrical storm
On January 01, 2001 at approximately 3:30 p.m. one employee was electrocuted when he came in contact with a single phase
Employee #1 along with his foreman were in the process of landing a piece of tower structure to be added to the top of this com
March 7, 2001. At approximately 08:00 a subcontracted tower crew of three tower hands and a crew leader arrived at a wireles
Employee #1 was standing with in 6 ft. on the back side of an i beam they were in the process of bolting in place to replace a su
On April 12, 2001, between 2.30 pm to 3:00 pm employee was working alone in the process of removal of 10 KVA transformer.
A bridge was being constructed. On one span of that bridge, sheet metal decking had been incorrectly installed over the openin
EE #1 was breaking up concrete to be put in a dumpster when several concrete blocks held together and held to the overhead
June 23, 2001, approximately 3:00 pm. A three man crew had finished the week of welding work inside a new power plant exha
The project was the construction of lightweight metal building for use as a church. Triple L Construction was to provide the conc
The project was the construction of lightweight metal building for use as a church. Triple L Construction was to provide the conc
10-20-2000. Welding company has a job on an oil well site to install and repair a metal ladder to a 210 barrel production tank be
September 17, 2001. Approximately 11:15 AM. Crew of 6, and Owner were finishing roofing phase, carrying a section of roofing
on may 7, 1996 at approximately 6:45 pm, the deceased was buried when a trench wall caved in pushing him against a concre
on april 22, 1996 at about 9:30 pm, the feed water pipe supplying the number 6 boiler ruptured causing steam to permeate the
victim crushed between dump bed of truck and frame. Crushing injuries to neck and chest area causing loss of vacular and oxy
see osha-36 #100650050


                                                     Page 125
                                                         all


employee had completed installation of roof gutters on a residential building and was carrying a 24 foot aluminum extension lad
on 8/20/98, at approximately 5:26 pm, a superintendent using a rental truck crane to load pipe onto a trailer made contact with
flagman was struck motor vehicle
on 03/10/99, at approximately 7:50 am, employee 1 made contact with an overhead power line while inserting a 14 foot long reb
see case file notes:
Truck maintenance employee was greasing the drive shaft of an off road dump truck for use in the land fill. Dump bed was in th
1) Employee #1 fell thru a floor opening while setting trusses. The employee's ladder was placed close to a floor opening meas
Employee #1 was climbing up a ladder in order to inspect a leaking roof. Roof eaves were about nine feet. Aluminum extension
employee was working at the 250' level of a tower antenna. He attempted to secure himself with his safety lanyard to the tower,
employee was working at the 250' level of a tower antenna. He attempted to secure himself with his safety lanyard to the tower,
the deceased was an electrical mechanic who was about to take the test for journeyman certification. His job was only to put th
employee had gone on to a single story roof with another plumber to join together a water line. They were having a problem kee
employee was performing work (flagman) on I 95 when struck by a motor vehicle traveling north on the interstate. The crew wa
decease was operating a bobcat and looked out to check load and was crushed by arms. The safety latches on the seat bar we
on 09/03/96 at approximately 10:30 am employees were removing taper tie and ground anchorage from a 70 feet long max a- f
on morning of 08/14/96 the deceased was working with another man installing a fence a installing fence posts. The deceased w
the employee was removing mechanical equipment from the mechanical room of a draw bridge. He and his crew had just remo
an employee mopping "hot" tar backed off the roof and fell approximately 12 feet to the ground.
employee was picking up warning sign on a highway construction site when he was struck by a concrete truck.
the victim had been hired two days earlier. The day before the accident he has been assigned to move insulation from the food
on october 2nd 1996, at about 10:20 a.m., employee was laying steel deck pans on the roof of international corporate park, bui
four employees were located within a trench measuring approximately 79 feet long, 10 feet deep, 7 feet wide at the top and 6 fe
four employees were located within a trench measuring approximately 79 feet long, 10 feet deep, 7 feet wide at the top and 6 fe
four employees were located within a trench measuring approximately 79 feet long, 10 feet deep, 7 feet wide at the top and 6 fe
four employees were located within a trench measuring approximately 79 feet long, 10 feet deep, 7 feet wide at the top and 6 fe
the victim was part of a crew of ironworkers setting bar joists to support a metal roof deck. He stood on existing joists and leane
during a demolition job, the roof and columns buckled and crashed on the workers.
during a demolition job, the roof and columns buckled and crashed on the workers.
the deceased was working on an expansion of an existing system and had pulled wires into the service room to be connected t
fatality.
employee fell from flat roof to his death approximately 18 feet.
on 7/15/97, approximately 1430 hours, 4 employees who were working to install nailers on a roof parapet were beginning to get
at about 11:00am, employee #1 was in the process of loading a bulldozer onto a flat bed truck for transportation from the emplo
employee attempted to start a tractor which was in gear while standing on the ground. When the engine engaged the rear tire r
the decedent was part of a crew installing an outdoor swimming pool screen enclosure for a single-family residence in a new de
employee was attempting to drive a pry bar through an epoxy liner of a manhole so that water from the installation process wou
fell through a skylight: employee was working on a roof performing stripping operations. He was removing a plastic and some d
employee was part of a concrete finishing crew placing concrete on the second floor patios of a custom residence. While the re
employee had been using a gasoline powered concrete saw in an enclosed area. He had stopped work for lunch, however, upo
on or about 11/04/97 employee was working near the chute on the ground level assorting lumber when another employee work
on october 18, 1997, the decedent was the foreman of a four-man crew of qualified electricians who were working to transfer el
on or about 7//24/97 at approximately 3:00pm employee was cleaning the oil pump on the elevator. He was found slumped ove
employee reached into the top of an air conditioning/ heating unit and came into contact with an energized side of an heating el
employee had returned to work following lunch as he was preparing to start he stepped on a hole cover and the cover slid out f
on or about 01/14/98 employee was installing exit signs on a new building when he fell from 8 feet "a" frame ladder to a concre
employee was working on a swing stage and came into contact with a electric distribution line. The employee was measuring a
employee was killed while he was standing ona permanent walkway which collapsed and fell 24 feet
on 03/02/98 t approximately 10:30 am employee was installing window buck at the 10 story level fell from the balcony.
deceased was hoisting a rebar when the rebar contacted high power overhead lines.
on october 14, 1997 around 1:58 pm, an employee operating a truck mounted crane (pitman- uni/dyne ii turret, model pc3fd2 e
employee was working on a ladder adapted for painting tanks. He attempted to dismount the ladder and unhooked his body ha
on 01/16/98 at approximately 11:50am employee was found bleeding from the face possible fell from ladder. No eye witness to


                                                     Page 126
                                                           all


fell from elevation.
on 04/17/98 employee was working on a three phase,480 volt circuit when his forearm touched a live part of the equipment unin
on november 29, 1997 between about 1330 and 1400 hours, an employee took the ladder from the side of the personnel hoist
on or about 9:30 am, january 7, 1998 employees a and b were standing on a scaffold platform about 11 feet above the lower le
an employee was electrocuted while using a drill inside an empty pool.
on july 2,l998, employee was installing dimmer switch after removing outlet box. The employee make contact with energized wi
on 07/15/98 at approxiamtely 8:00am employee was installing windows on a new building when he fell 135 feet to the ground. E
employee #1 was inside a 4 foot excavation, removing a fitting from a "cannon" pipe, while the backhoe operator was about to u
employee burned to death when contact with energized lines resulted in fire fueled by hydraulic fluid.
on 7/20/98, employee was working from a l6 foot ladder measuring the wall area wbove a window in order to install a canvass c
on 7/l6/98, at a single story home construction site employees installing sheeting on a 5/l2 pitch roof fell off the eve. One man s
on july 27, 1998 an employee beginning to remove plastic over extended himself and fell from an elevation hit his head. He was
employee came in contact with high power lines and was electrocuted.
on 9/24/98,two employees installing new facia boards while working out of the aerial snorkle cage made contact with a 7200kv
on 9/24/98,two employees installing new facia boards while working out of the aerial snorkle cage made contact with a 7200kv
xxx
employee a was on the bed of a flat bed trailer helping to guide a concrete piling which was being lifted by a bucyrus erie mode
on 09/29/98 at approximately 2:10pm employee was installing trusses on a single family house. When one of the trusses alread
employee working close to roof edge apparently lost his balance and fell to his death.
on october 14, 1998 at approximately 9:00 am, an employee who was part of a 4 man landscaping crew planting palm trees wa
an employee working 30ft above ground unhooked his safety harness while changing positions. He lost his balance and fell to t
employee laying out wall framing fell 12 through a stairway opening. The opening was covered by a drop ceiling which was inca
a roofer working on the re-roofing of a single-story flat roof at a church building fell 10- to his death. The victim was rolling out ro
employee working in a confined space died from drowning.
employee was assigned to tear down the remaining portion of a forming platform. The employee attempted to pull off some plyw
on 11/18/98 employee was supposed to hold an aluminum extension ladder for other members of the crew that were working c
on 01/08/00 at approximately 11:50am a 67 year old carpenter was doing formwork on the tower of a new building that was und
a painter working at a single-family residential development fell 12- to his death. He was painting the upper facia trim on a 2 sto
an employee was laying down metal decking over bar joists when he fell 13- to a concrete floor below.
on february 22, 1999 at approximately 1:00 pm, employee was pitching 3x6 feet pieces of glass from the back of a chevrolet cu
employee was pushing mobile scaffold from the side across a floor covered with fireproofing overspray with an employee on the
an employee demolishing a fireplace/chimney was crushed by bricks falling on him.
mdta bus struck a compressor that was improperly parked and encroaching into the roadway. The compressor was trailer mou
on april 7, 1999, a case model 621 front-end loader was driven by one of the foremen at a construction site. Employees were in
a carpenter/laborer was placing pins at the top of a column form with the safety lanyard of the full body harness looped around
Employee #1 was struck by a trash haul truck. Employee #2 was backing up a trash haul truck when suddenly he saw Employe
on 4/13/99 inside the building under construction an employee was climbing the outside of an scaffold that was approx. 19 feet
employee was straddled the trusses while trying to adjust the girder truss with a pry bar. The pry bar slipped and he lost his bala
----------
a laborer was operating a traffic roller used for finishing asphalt coatings in reverse and the back wheels went off of the road on
Employee was painting on a makeshift scaffold made by aluminum plank laid across 25 extension ladder and the knee wall. W
employees were setting a concrete street light pole in close proximity to a 138,000v. powerline when it swung causing the light
employees were setting a concrete street light pole in close proximity to a 138,000v. powerline when it swung causing the light
on 10/04/99 employee was electrocuted while in the process of relocating a submersible pump unit to pump out about six inche
employee was working 3 feet up on a ladder, when he fell backwards onto the ground resulring in a fatality.
An employee jumped into a canal that was connected to the intercoastal waterway, swam approximately 100 yards, and drowne
the employee was working inside a ground building box that was located in the ground between the two towers under construct
an ironworker was at approximately 19 feet under a partially unsecured open web steel joist when the foreman decided to unrig
deceased had erected a six foot scaffold which was placed on unstable ground and then placed a ladder on to it . the deceased
a crew of two were performing demolition of a pier using a linkbelt ls-78 serial # 7d986 crawler crane on a barge that had a mec
On 01/14/00 at approximately 3:15pm a concrete block wall collapsed toward the interior of the building. Five (5) employees we
On 01/14/00 at approximately 3:15pm a concrete block wall collapsed toward the interior of the building. Five (5) employees we


                                                       Page 127
                                                         all


A carpenter's helper on a high-rise construction site stepped on an unsupported piece on plywood formwork and fell 14 floors to
an employee was cutting concrete with a gasoline powered concrete cutter in an elevator shaft recessed approx. 5 feet from gr
while removing concrete forms from the ninth floor 56 feet above ground and not wearing any fall protection, the victim lost his
The victim contracted with City of West Palm Beach to install the plumbing for a memorial which was being built to honor the m
A handyman was hired by a local doctor to relocate several electrical outlets at his office. This required that he and his helper e
Employee #1, employee #2 and employee #3 were working inside an excavation (approximately 14 feet by 14 feet x 4 feet) rem
Employee #1, employee #2 and employee #3 were working inside an excavation (approximately 14 feet by 14 feet x 4 feet) rem
On a site which is to be a school for Miami- Dade County employees were forming a roof parapet. One of them had been told b
Employee performing surveying operations on a four lane road at the end of a highway construction project. The construction s
An ironworker installing glass skylights into a hotel atrium space frame fell 58 ft. to his death. At the time of the accident, he wa
An employee waterproofing a condo planter was hit by a falling roll of roofing felt and died several days later of his injuries. The
The victim was alone in a townhouse when his boby was discovered 8 feet 10 inches below an unguarded landing on a concret
The deceased was the foreman for a crew which was installing traffic control signs along a secondary road. On the day of the a
On 03/02/00 at approximately 1:00 pm an employee was walking on the east sidewalk of a four- lane road while locating underg
An electrician was on an 8 foot A-frame ladder in the process of installing conduit for a step down transformer for a swimming p
Employee was working at the 60 foot level of a tubular frame scaffolding handing forms up to another employee. He was report
Two employees working for the signal contractor who had installed the street light system where sent to repair a broken piece o
Two employees working for the signal contractor who had installed the street light system where sent to repair a broken piece o
The victim was using an 8 foot A-frame stepladder to find a groundfault on a 24 Volt fire alarm system when he fell with the ladd
Employee operating a 1984 Galion Asphalt Roller s/n 60902, having a gross weight of 12000 pounds along an asphalt sidewalk
Employee re-installing insulation found lying at the base of an eight foot a-frame ladder. It appears tthat the employee was eithe
Demolition employees were removing a concrete stairway in a four story building being renovated. They had finished chipping c
Demolition employees were removing a concrete stairway in a four story building being renovated. They had finished chipping c
Demolition employees were removing a concrete stairway in a four story building being renovated. They had finished chipping c
On 10/4/00, employee #1 and employee #2 were standing on a flat roof of an office building about 30 feet above the ground lev
On 10/4/00, employee #1 and employee #2 were standing on a flat roof of an office building about 30 feet above the ground lev
Employees #1 and #2 were instructed to pick up traffic cones and barricades not being used at a road construction work site. W
A pool service employee drowned while cleaning a swimming pool at a duplex. There were no witnesses to the accident so no o
A truck driver in the process of dumping overburden into a lake backed up through a four-foot high loose soil berm and ended u
On the morning of the accident the employee had inserted an inflatable plug into a storm sewer pipe located at a street drain so
On December 4, 2000, at approximately 3:00 pm, employee #1, as part of a 5 man crew was installing roofing tiles on a residen
Two iron workers were assigned to close up an opening on the roof and install facia along the edge of a section of roof which h
Two iron workers were assigned to close up an opening on the roof and install facia along the edge of a section of roof which h
On November 7, 2000, at approximately 10:45am, employee was proparing to release cables that were holding a 180 foot truss
On February 19, 2001 at approximately 2:00pm Employee who was checking fiber optic connections in a computer room was f
On 11/13/00 at approximately 2:30p employee was standing on operator's platform on the right side at back of drill rig when he
Three employees were assigned to install metal panels on the a roof of a building which was under construction. Upon mountin
Employee was standing on the second floor balcony that had its guardrails previously removed He was discussing work that he
On March 14, 2001 at approximately 11:00am, an employee who had been monitoring the work being performed on the north t
Employee #1 and employee #2 were working on a two-point suspended scaffold with insufficient counterweighting approximate
Employee #1 and employee #2 were working on a two-point suspended scaffold with insufficient counterweighting approximate
The employees were preparing to sheet the trusses which had been installed on a single family dwelling the day before. The de
On July 10, 2001 at approximately 10:00 am, employee #1 and employee #2 were working on the roof of the building approxim
Employee #1 was doing some general construction work around the yard of the company when he bent down and fell over. It w
Employee was working alone on a roof and slipped and fell to the ground employee was self employeed.
On 11/1/00 at 11:00am employee #1 was assisting a pick-up truck which was stuck in sand. The employee after pulling the pick
Employee was working on the 6th floor nailing wood guardrails at the #1 stair shaft. He stepped past the guardrails onto the for
On Tuesday, August 14 at approximately 2:00 pm an employee who had been operating an electric concrete coring drill on the
employee had a heart attack and fell from scaffolding and employee struck ground and had head trauma
worker was a self-employed plumber with no employees. He was hired by the owner of the industrial complex to do some plum
employee was delivering drywall to a construction site at armstrong school with a flat-bed truck belonging to him. He had driven
employee while standing on roof edge washing down the exterior of the building with a garden hose fell from the roof.


                                                      Page 128
                                                         all


on 9/22/99, while performing electrical work in the basement of 117 union street, Easthampton, MA (bela italia restaurant) emp
an employee, along with his employer, was working from a pump jack scaffold at a height of approximately 18 feet removing an
Operator was operating tractor with backhoe and loader attached to it . it tipped over,the operator became pinned under it, caus
fall from work platform
A plasterer was working in the steeple area of a church making repairs to the previous plastering job. He was standing on a ma
Victim was working on a ladder jack scaffold approximately 20 ft high when one of the ladders slipped, knocking him off the sca
Employee was standing in bucket of excavator tieing wires together with rope at a height of approx 14 FT. The operator of the e
on or about 04/11/96 a service technician for h.v.a.c. technical, inc. was on the property of revcor molded products to replace t
on or about 12/27/95 employee was in the process of making a final tie in to switch gear. He assumed the circuit was dead and
on or about 06/14/96 approximately noon the equipment operator proceeded to a location to do some site clearing. The equipm
on or about july 19, 1996 employees were doing a sealcoat job located at the texas dot facility in brownwood, tx. The process w
on or about july 10, 1996 two employees were working from a 2 point suspended scaffold painting a water tank. The employees
four employees were installing a raised section (copola) to an existing roof for ventilation purposes. This process involved cuttin
the deceased employee was leaning on the concrete truck. A boom operated within 10 ft of a 7200 volt overhead line was ener
on or about june 26, 1997, 1:15 pm employees were engaged in disassembling and adding a 20 foot boom section on a fmc lin
employee was operating a case 580l backhoe, bucket full of white rock. The employee was in the process of descending, at an
the employee was cleaning switchgear and come in contract with 6.9 kv electric buss.
at approximately 11:30 am on 12/1/97, an employee was carrying a bundle of insulation while walking on the roof, no eye witne
employee was working off of an approximately 20 foot aluminum extension ladder that possibly contacted an overhead electrica
employee pouring channel concrete got to close to the power line. Employees were using a concrete bucket.
employee 1 was standing on a 6-foot mobile scaffold making measurements prior to the installation of vertical studs for interior
A 56 year-old male was contracted by housley communications inc. to conduct boring operations for underground communicati
an employee work crew was engaged in the installation of a standing-seam metal roof following their having completed the inst
on february 16, 1998 at approximately 11:40am; linder-stahl construction co., inc. had a crew of 5 employees working at 1200 b
employee was working on an approximately 17 foot steel column that was being erected and slipped and fell to the concrete flo
construction employee fell from the second floor opening of a residential development site and struck his head. Employee was
employee was attempting to take material from the roof area by a skytrak fork lift, model 6036b, sn 2193, and was on an incline
an employee was washing out a concrete mixer truck using a water hose. Another employee was using a front-end loader to m
employee cecilio medina was drilling a hole into the ground with an auger and apparently struck an underground 240 volt powe
on july 7, 1998, at the 9500 block of boat club rd, at approximately 2:30pm, an employee, an experienced operator, was operat
on october 31, 1998, at approximately 3:30pm, three construction workers were injured, one fatally, one hospitalized, the other
the 7 man employee crew had been working taking gutters off of the approximately 27 foot roof for about ten minutes. After thro
employee made contact with a live buss and was fatally electrocuted while attempting to tie in a new 4000 amp section in an ex
roofers were removing plywood decking and insulation from a flat roof approximately 21 foot from the ground. Four employees
employees in a construction crew were building an extension sewer line which was to tap into an existing city line. The crew had
employees in a construction crew were building an extension sewer line which was to tap into an existing city line. The crew had
a fiberglass manufacturing plant hired a contractor to conduct a scheduled overhaul of one of its production ovens. Part of the o
a fiberglass manufacturing plant hired a contractor to conduct a scheduled overhaul of one of its production ovens. Part of the o
on or about august 31,1998 an employee, working in the attic of a residence, was feeding "fish tape" into the top of a breaker b
the employee loera perales was riding on the bobcat plate(near bucket) when the operator struck a curb, the operator inadverte
an employee was riding the bucket of a model 853 bobcat front-end loader when the operator inadvertently hit lift activator lifting
on or about march 3, 1999 two employees were in the process of moving a boat & trailer when the mast of the boat hit an overh
employee #1 was installing roof sheathing materials on a house designed for a 10 in 12 pitch roof. The work was conducted du
clamp holding cable came loose, releasing work safety platform/scaffold which landed on top of employee, impaling the employ
employee fell from bed of tractor trailer and sustained a head injury and died a week later.
employees that were interviewed had been informed that fall protection equipment was provided by lile construction for all contr
employer did not use the proper benching and sloping method outlined in 1926.652, appendix b-1.2 for single benching for type
The owner of Eddy Harris, L.L.C. was standing on bridge when it collapsed. He fell to his death. he was standing on the bridge
A construction worker was killed after spaying lacquer on woodwork on the first floor of a 2- story house. The worker was burne
A worker was cutting a hole in the rafters of a roof for a residence where a chimney was to be installed. The worker fell through
An employee was working in a trench about 7.8 feet deep and was struck by a butterfly valve and pipe connection about 46 inc
An employee of Mica Corporation hit a power line with a hydraulic crane near marker 362 on I-35 just south of Hillsboro on the


                                                     Page 129
                                                       all


At 4:03pm, 10/19/00, the public information officer for the Ft Worth Fire Department, reported a worker had been struck by a st
On 9/23/00 at approximately 3:00pm three employees were servicing a 490 diesel truck, when another employee started the tru
The Manitowoc and Hi-Ranger were working on a cement pole installing insulators, the Hi- Ranger positioned to the rear of the
A brick worker was helping the brick layers brick a house. He was sitting on the scaffold, he collapsed and went into convulsion
struck by machine
On 11/28/00, an employee fell approximately 45 feet to lower ground level, when he was elevated on the forks of skytrac forklift
A crew was erecting steel to build a structure. Employee #1, accompanied by Employee #2, approached the cab of a crane afte
On November 20, 2000 an employee was fatality injured while attempting to lower a concrete form weighing approximately 330
Employees on a road work crew were picking up debris in the median of an interstate highway. Employee #1 walked ahead of t
Employee was using a trolley to lower a wheel barrel onto the ground. The trolley was not equipped with a counterweight. When
On or about September 1, 2000 two workers were installing an antenna on a 300ft communication tower when the cable of the
An employee was loading a backhoe used at this site for transport to another site. The employee was driving the backhoe up th
An employee was using a water hose to clean the auger of a Pavematic Form Riding Paver Model FP-3200 while it was running
Two employees were installing jumpers on an electrical transmission line from a Terex hydraulic crane with a 2-man basket at a
Employee was working on outside light switch at a customer residence, and was electrocuted.
An apprentice electrician was climbing down a job made ladder from the second story of an apartment complex under construc
A plumber's helper was electrocuted from a metal cover over a drop lite borrowed from the homeowner. The employee was fixi
employee was working in a 7.5 foot deep trench laying sewer pipe. At a depth of approximately 4 feet and running along the no
employee was working installing sewer piping in a three foot wide x seven foot deep unprotected trench that also contained a h
an employee was fatally injured when he cut a steel beam from the basket of a lift and was struck by an electrical conduit that p
an employee was fatality injured when he fell approx. 6' from a 10' stepladder while trying to retrieve material from overhead.
A 38 year old carpenter was talking to a fellow employee about the job they were involved in (installing lock sets in doors) when
at approximately 12:05 pm on 10/31/97 the president of lps of latham ltd was working on a new holland l785 skid steer industria
on february 4, 1998 at 2:55 pm employee was in the process of threading boring rods together so that they could be pulled bac
on 4/28/98 at approximately 11:00 am., the employee was working from a ladder. The employee was in the process of removin
employee was using a ladder 120 feet above the ground while carrying a 50 pound canister of welding rods on his shoulder and
on 9-10-98 at approximately 12:33 pm, employee #1, foreman for callanan industries was guiding a 10 wheel dump truck up an
on april 27 at approximately 10:30 a.m., two employees were working cleaning up debris from a recently completed roofing job.
two employees were working around a wood chipper machine. These employees were feeding branches cut from trees being r
1. Employee was in the process of checking out area of roadway being paved in order to establish striping and pavement mark
victim was standing at the rear of a dump truck which was loaded with a kobelco sl 200 mark iii track hoe. The victim had pulled
an employee was fatally injured when he fell approx. 10' from a ladder while trying to reach an area under a window that neede
Employee was installing furring strips while working from a 32 inch wide by 6 foot high Baker Scaffold. The employee was using
Employee was working from a 13.2 foot high tubular welded frame scaffold without any fall protection system in place and the s
The owner of the companywas removing an old roof when he fell through a rotted section approx. 30' to his death.
On 7-20-01 at approximately 1:30 PM the employee was attempting to gain access to a ladder from the roof of a house under c
employee was operating a large backhoe on a bridge at night. He was lifting concrtet slabs to remove them from the bridge. Th
employees were stretching a fence in the process of fastening it to already erected rails on the side of an overpass bridge. The
an employee was grinding a yellow line off of an interstate highway. behind the employee was an arrow board with a moving arr
the foreman for darby creek excavation was working to make a correction to the sewer line on december 29, 1998. The depth w
employee taking apart the boom sections knocked out the pins while working underneath and was crushed thereby resulting in
two employees were in an aerial lift (bucket truck) hooking up steel (steel erction). The bucket got caught on a beam and the em
at approximately 0830am, 26 may 99, employee fell 25 feet 8 inches to his death. The employee was helping install a standing
at approximately 1:45pm, 8/20/99, employee was seated atop a structural steel beat at 12 feet 11 inches assembling a roof fram
at approximately 7:45 am on september 30, 1999, two employee were guiding a load of steel augers that were being transporte
at approximately 9 am, 10/29/99, employee was raking gravel next to concrete block wall in preparation of pouring the basemen
employee #1 who was rewiring an elevator, entered the cab (car) to move the cab down so employee #2 could get on top of it.
employee was cutting holes for downspouts in a gutter system the crew had just installed for an apartment complex. While carr
At approximately 2:20PM, 23 June 2000, a year old laborer was killed when he was backed over by an asphalt truck. Employee
At approximately 14:30, 07 September 00, employee was trapped under a vertical transfer lift (VTL) and crushed. The employe
On September 06, 2000 an employee was working on a low slope roof, outside of the warning line system and fell approximate
At approximately 1252pm, 26 Sep 00, employee fell in excess of 30 feet to his death. The employee was helping remove metal


                                                    Page 130
                                                         all


Employee working in trench was fatally injured when an ESCO bucket attached by a JB Hendrix Coupler to a Komatsu PC400-
At approximately 4:50pm, 13 Dec 00, employee fell 26 feet to his death. The employee was helping install a metal roof on an no
A man was digging a trench for a cousin in his yard and got off of the backhoe and went into the trench. The sides caved in and
On April 17, 2001, an employee working from the bucket of an electrical truck received an electrical shock while helping to insta
At approximately 12:30 pm, 12 Apr 01, an employee walking in the attic of a new house fell through the ceiling. The employee w
On 6/22/01 between 8:00 am and 9:00 am, an employee was performing work removing ceiling tile, light fixtures, and/or wiring
An employee was riding on a spreader box behind a dump truck. The box hit a tree stump and "jumped" up causing the employ
on 10/10/97, three employees of shawnlee construction, inc. were using a base-mounted drum hoist to raise a framing membe
a carpenter fell 15' from a ladder while installing a lenght of trim molding on the new addition of a private residence. An employe
on 6/4/98 at approx 1:00 pm eagle elevator co, inc. employees #1 mechanic and ,#2, mechanic's helper were working with emp
on 5/25/99, at approx 4:30 pm, osha bnao received an emergency response pager message regarding an employee fall from a
steel worker was working at the site address of 675 watertown street. The worker was connecting a steel beam at the highest p
owner of construction co fell approx 8 feet from a portable ladder while coming down from low roof and struck his head on the p
The owner of Olympic Contracting Company was on a scaffolding system that he set up. The system collapsed and he and a c
The owner of Olympic Contracting Company was on a scaffolding system that he set up. The system collapsed and he and a c
Employee was working on the roof of a three story home when he fell to the driveway 35 feet below.
EE fell 19 feet from second floor of the 4 plex.
Employee fell from the top of steel 40 feet to the concrete floor below.
employee was troubleshooting to determine why an air handling unit continued to trip out after running for only a short period of
Emplpyee worked for Granite Construction Co. several different times, starting in 1990 as a tire man. In 1993 he worked on the
employee operating a track hoe moved in front of tower 100 + high during demolition work and the tower fell, pening employee
An employee, 41 year old fell from the ceiling joist of the roof structure as he was lining up roof trusses to be attached to the joi
a gin pole dwas being installed on the side of a 1500 foot high broadcast tower to facilitate the changing of the antenn on top of
a gin pole dwas being installed on the side of a 1500 foot high broadcast tower to facilitate the changing of the antenn on top of
a gin pole dwas being installed on the side of a 1500 foot high broadcast tower to facilitate the changing of the antenn on top of
The accident happened on the south side of the apartment complex located at 2101 N Haskell at approximately 4:45 pm, on Ap
The home owner called Quiegley Heating & AC to install a combustion air duct in the closet enclosing the heating system. This
an unqualified electrician helper with only 3 weeks of previous electrical experience was assigned the task of connecting fluores
fel while installing rafters - reporting employer uncertain of details - therefore form is incomplete. *employee died 2-8-94 appx 1
CalHar Construction Inc was awarded a contract from the City of Plano to re-route a 8"X 8" culvert between Alma Drive and Le
abstract
abstract
was removing a ground wire which should not have been removed during his work activities: upgrading an electrical transmissio
Woodbine electric received a service call from an official at the Shell refinery on Hwy 31. An Electrical Technician for Shell calle
taylor's welding, subcontractor to metal concepts of paris, was fabricating a new store roof over an exisiting roof. Taylor's emplo
employee was working a the bottom of a ten foot pit, which contained argon gas, employee passed out and a second employee
abstract
company officials said they were installing a 8" ductile iron sewer line, and manholes on hwy 31 for the city of longview. The tre
a worker fell from the bumper of a moving truck, striking a fatal blow to his head on the asphalt surface in the center of the high
an employee was unrolling roofing felt near an open sided edge of a low-slopped roof. The roof was 50 feet above the ground l
a employee was moving a truck mounted crane to a different location within the storage yard, to pick up a tank tha had been pu
victim was working from a section of form support at the 11th floor level when the concrete through which the platform support
an employee of jet concrete was killed when he was struck by an overhanging load of wooden building trusses on a semi trailer
while installing an iron ornamental fence gate an employee was struck. During the installation, the gate struck the north wall res
on june 17, 1998 around 5:45 p.m., a crew of framers were placing plywood on the exterior walls of a second floor apartment b
employee of casey electric company was killed by electrocution when the drill he was using inside the housing of a roof air cond
an employee of skyline erectors was killed when he fell while installing steel roof trusses at a height of about 20 feet. He was w
employee was cutting a concrete curb and slab into a building support column. In an effort to complete the cut into the column t
employee was electrocuted when a 40 foot extension ladder inwhich he was holding came in contact with a main phase 7620 v
on december 12, 1998, an employee was electrocuted while installing a generator. The crane, which moved the generator, stru
on november 18, 1998, an employee fell through a mechanical opening while helping to instal hvac material.
employee was walking on a roof carrying a roll of roofing felt. Employee slipped in the valley of the roof and fell 2 stories (appro


                                                      Page 131
                                                         all


victim fell through second story stairwell to bottom floor. The accident site was a 1 1/2 story residental new construction. Framin
on sept. 15, 1998, at around 10:30 a.m., employees were performing roofing work activities at an apartment complex construct
employees were working at the site conducting general cleanup. Two employees were sitting on a curb taking a break. An emp
the victim was tacking a 10 foot section of sheet rock to a wall section. He was standing on the third or fourth step of a six foot a
an employee engaged in installing roof decking on a structural steel building fell to the concrete floor below, a height of 19 feet,
employee died as a result of injuries sustained when he inserted his head partially through an 8 inch by 19 inch window opening
victim was moving a 7'x 5'x 6" pre-cast concrete wall. He was attempting to make lateral corrections (normal operation) when th
an employee working on the third floor, of a building under construction, was struck by multiple precast concrete panels when a
the employee died as a result of direct contact with electrical systems of approximately 7,200 volts. The victim was the crew for
sunday september 5th, at about 10:15 am, a worker fell about 12 feet when a scaffold outrigger gave way. The worker was hire
employee was directing a cement truck, at approximately 6:00 a.m. into construction area. Employee was struck by an oncomin
an electrician helper was electrocuted while working on top of an industrial food storage freezer while tracing a route for a heat
employee( equip. Op.) was under 6 thousand pound milling/rumble machine changing cutting teeth bits. Employee failed to re-i
victim was working in the median of a section of new street at a highway intersection finishing concrete curbs on the east side o
employee was placing 22 gage metal roof decking on steel structure frame, which would later be welded in place, when he step
victim fell approximately 50 feet from a roof to a cement parking lot below. The victim was walking the roof line apparently inspe
autopsy report revealed cause of death arteriosclerotic cardiovascular disease. Right coronary artery 80stenosis by atheroscler
An employee was working on scaffold installing drywall inside a house and fell off scaffold of 2 tiers approximately 6 feet each.
Employees were unloading cases of glass from a truck with a fork lift truck and the cases became unstable and began to tip an
employee installing steel roof decking at a height of between 28 and 36 feet from the concrete floor below was not using fall pro
The victim was attempting to stand on a 2 X 6 inch board apparently supported on two end supports of some kind and the boar
on october 27, 1999, a crew of two employees were working on an excavatioin project at malone and stacey rd, allen, tx. The p
on october 12, 1999 at around 10;00a.m., a crew of dirt contractors, were operating a scrapers and other earth moving equipm
a construction fatality occured when an employee working on a mast climbing scaffold fell through an inadequately secured por
victim approached the 4th floor unguarded balcony and attempted to throw an extension cord down to a temporary power pole
The employee was operating a Lull high reach equipment when it rolled down an embankment resulting the haed of the employ
Two employees were working in a man basket lifted to a height of approximately 35 feet by a Lull rough terrain forklift when the
Employee fell from about the 60 foot level from a structural steel structure where he was doig steel erection. He had just compl
A Master Electrician employee was standing on the outside concrete while working in a service enclosure in the process of con
On March 17, 1999, at around 9:00 a.m., a roofing crew was removing the built-up roof and the roof insulation upon Building 11
An employee of an electrical contractor fell while attempting to adjust lights on a newly constructed light system at Southern Me
Two employee were riding on top of a load of roofing scraps on a stake bed truck enroute to a dumpster on the job site when th
The victim an employee of Win-Con Enterprises moved from the fifth floor to the fourth floor by way of the stairs of the Double T
An employee fell into a 10 foot deep pit which contained water at 136 Degrees F and had a PH of 10.5. He stumbled while carry
An employee of 5-tar Foudation Company was killed when a leaning brick wall which he was attempting to realign to the vertica
The victim an employee of D&D Roofing was conducting resurfacing work on the roof top at 2631 Lombardy Ln., Dallas, TX 75
Employees of Pate Brothers Construction were installing a new sanitary sewer for a new housing development in the City of Irv
The site is a tunnel with a 132" metal sleeve into which a 96" concrete pipe is fitted for water flow. The pipes are placed into the
Masonary employe fell approximately 16 feet from scaffolding. The scaffolding material from which the employee was standing
Employee fell about 24 feet from roof level to concrete floor below while installing sheet metal roofing on a structural steel build
Employee was struck by a mobile scaffold that toppled over while he was pushing it across a concrete floor. There were no eye
Two persons were in a trench approximately 10 feet deep when the wall of the trench collapsed. One wroker was pulled out bu
A motor grader operator was scraping a haul road at a construction site. The operator drove the grader across the temporary ra
On or about 09/19/00, a concrete contractor and his crew, were working with a concrete truck operator. The employees were p
In late December 2000, a severe ice storm in East Texas and Southwest Arkansas damaged a large number of power lines, ut
Employees had moved around 85 sheet of 4 X 8 foot particle board from outside the home under construction to inside and lea
Three men were working attaching overhang gang forms to the overpass construction of Hwy 161 at the connection of Hwy 635
The victim, an employee of Arnold Construction Company was in the process of unloading some trench boxes from the back of
A welder working in a 10-foot, 3-inch deep excavation without a protective system, to cut a 60- inch diameter culvert was struck
The victim, an employee of Battson Contracting Utility Construction was in the process of setting up a traffic message board. W
The job superintendent was struck-by and run over by a rear end dump truck that was backing up on a section of highway unde
The Home Builder (Employer A) has been building custom homes throughout the Dallas area for more than four years. Employ


                                                      Page 132
                                                          all


the victim was operating a tractor, traveling parallel to a highway, when the tractor struck a culvert endwall, knocking the victim
the operator of a sky trak rough terrain forklift equipped with a trak 12 foot truss boom was fatally injured when the forklift tipped
roofing contractor employee fell 68 feet while working at fairbanks morse, 701 white avenue, beloit, wi 53511.
two roofers were seriously injured (electrical shock and burns) when a 27 foot long aluminum track platform hoist (ladder type)
two roofers were seriously injured (electrical shock and burns) when a 27 foot long aluminum track platform hoist (ladder type)
An employee working inside a cooling tower fell approximately 30 feet when one of the structural members of the tower that the
Semi truck traveling on highway failed to heed traffic warning signs crashing into front vehicle which in turn struck flagger. Fallg
One employee of an electrical subcontractor was killed when three parallel concrete masonry walls collapsed during high winds
On 6/4/01, over 56 yards of concrete was delivered to the job site by SPC (~3500 pounds/yard). Since the legal limit per shipme
While backing into a driveway, a concrete truck tipped over and crushed an employee riding on the side of the truck. The emplo
an employee considered a lineman first class electrician was in the process of preparing to climb down a power pole and as he
an employee was on the tin roof of a building in order to remove the tin and replace with new. He did not wear fall protection an
the two deceased employees were in the process of cold cutting a natural gas pipeline in order to install a new valve setting at t
the two deceased employees were in the process of cold cutting a natural gas pipeline in order to install a new valve setting at t
working as a pumper the employee was crushed on site. The weights mashed him against the base of the well rig.
A electrician's helper, while working from a power pole, contacted a live (7200 Volt) line which was above his head.
Employee used a hydraulic jack to lift the front of a 14 by 60 foot mobile home. He crawled underneath the front edge of the tra
3 workers (belonging to Diversified Energy Contractors Co.) and the truck driver (Leased to Daws, Inc.) were collectively engag
Employees were placing sheet metal, insulation, and chicken wire on the roof of a metal warehouse building being constructed.
Two employees were being hoisted up a 500 foot telecommunications tower for the purpose of replacing damaged antenna par
Two employees were being hoisted up a 500 foot telecommunications tower for the purpose of replacing damaged antenna par
Two employees were being hoisted up a 500 foot telecommunications tower for the purpose of replacing damaged antenna par
A roofer, one of 4, was nailing shingles along the edge of a second story roof at a height of over 20 feet. He was standing on a
This contractor was engaged in performing work at BFI, they were digging a ditch which was to have been used to run an unde
Midwest Asphalt Corporation, contracted by Jones Brothers Dirt & Paving Contractors, Inc., doing the milling work (grinding of e
At approximately 6:15 p.m. on 06/01/01, the victim made his final dump of the day. After making the dump, he turned his truck,
Deceased was standing directly behind a backing dumptruck out of view of the driver's rear view mirrors. The truck had a funct
employees were in the process of removing (1) 20 foot section of boom, to replace it with a 10 foot section. The deceased (#1)
employee was engaged in re-roofing a manufacturing building. He assumed that power lines in near proximity to his location ha
employee was engaged in carpentry work on this single family residence under construction. He was working on the 2nd floor w
employee was installing gutters on this residence under construction. As he was moving the aluminum ladder he was using, the
employee operating equipment within 10 feet of overhead powerline was not trained in the hazards associated with working aro
five employees were reroofing (shingling) a 2 1/2 story sorority house. During the tear off, one roofer fell 22 feet to the asphalt b
truck driver was raising the bed of the truck to load chipper machine when the dump struck a 7200 volt overhead powerline. Th
the deceased was working on a ladder and fell off of the ladder. He was working near/with electricity. There was concern that th
an oiler was checking the fluid levels in a "high head" pump when his loose fitting rail jacket was caught-in a large unguarded fa
an employee was electrocuted when he struck a 7,200 volt power line with a section of scaffold. The scaffold being erected was
an oiler was checking the fluid levels in a "high head" pump when his loose fitting rain jacket was caught-in a large unguarded f
employees (3) were working on a low slope (3 x 12) roof re-roofing a barn. The eave height was 13'8". As one employee shifted
the deceased was hired by the employer as a subcontractor. The decease was tightening bolts, to install the skyline from a 12 f
employees were engaged in breaking down drill rods being used in a boring operation. The rod tongs were attached to the borin
Employee was working from a scissor lift which was extended approximately 32 feet above the floor. He was installing brackets
Neighbor went to help a carpenter raise the next door house wall with other volunteers. The men got the wall braced, but 15mp
Employee was the foreman of the job. A new office building was soon to be constructed. The crew was digging up a water line,
On December 5, 2000 at approximately 8:45 a.m., Employee # 1 was riding on the step of a John Deere 310 SE Backhoe/loade
Employee was in the process of repairing a drain pipe in a warehouse. He went to the roof and inserted a 6" plumbers test ball
An employee conducting telecommunication wiring operations was killed after falling approximately 15 feet from a vehicle moun
The victim died in the trench approximately 13 feet deep, 11 feet wide and 17 feet long without cave-in protection. The employe
an employee was fatally injured when he fell approximately 70' to ground. He was securing the 2 point suspension scaffold and
an employee of karl kocc construction was operating a gasoline generator within a 20' long by 8' wide storage container. There
an employee climbing a ladder to reach the roof fell to the ground 16' below. The employee was taken to the hospital with a bro
on wednesday, august 12, 1998, employee #1 fell approximately 8 feet from a two point suspension scaffold, to the concrete gr


                                                      Page 133
                                                           all


employee #1 used a 3" x 10" wooden plank as a walking/working surface, within an elevator shaft, when the plank broke and th
on december 28,1998 at approximately 5:00 p.m., employee #1 was underneath an industrial cargo scissor lift removing the hy
on 8/5/99 employee #1 fell 8' from a tubular welded frame scaffold to de-energized subway tracks below. The employee succum
the owner of a demolition company was dumping a load of old concrete at a concrete recycling yard. While he was standing at
an employee was welding a piece of angle support during the installation of metal decking on the roof of the building fell 25 feet
employee was in an excavation capping watermain. The temporary cap gave way and the force of the water submerged ee in th
Two employees were cleaning the rotating auger of a concrete paving machine, one employee's jacket got caught in the revolv
An employee was struck and killed by a car while repairing the road surface on a bridge.y
Employee installing felt roofing paper fell 30 feet to dirt from the unprotected roof eave. The employee was not provided with an
Employee straddling steel beam fell 20 ft to ground because the safety harness he was wearing was not connected to an ancho
 lead man was separating sections of roof decking into two separate bundles at approximately 8:00 a.m., 07-24-96. This activity
two workers were assigned to look for a missing plug in one of several manholes of an active sewer system. The two workers o
on 11-2-96 at 8:00 a m a laborer was using an agriculture type tractor with a front bucket attachment to move dirt from a pile to
a crew of construction workers were in the process of relocating a 60 ft long mobile construction trailer on a grassy area adjace
a worker used a metal folding ladder (variable position non self supporting) to climb to an 8 ft high roof eave to inspect the roof.
operator of a backhoe was in front of 4401 c samuel adams circle in a residential subdivision of scott afb under construction an
two (2) journeymen electricians and an apprentice electrician were preparing to install a new 480v switch gear into the main 480
two (2) journeymen electricians and an apprentice electrician were preparing to install a new 480v switch gear into the main 480
a crew of 5 workers were preparing a driveway for asphalt. The driveway is adjacent to a rural highway which has a 50 mph spe
employee #1 and #2 were working as linemen and installing new 7200v service by installing larger poles and increasing the ser
employee #1 and #2 were working as linemen and installing new 7200v service by installing larger poles and increasing the ser
A laborer was pushing 250-plus pound copper cooling plates along a 24-inch high, horizontal conveyor system towards the edg
at approximately 10:45 a.m., 06-16-99, general foreman was supervising the installation of metal 8'w x 12'h x 4"d shoring along
at approximately 8:30 a.m., 10-05-99, a laborer was observing the discharge of asphalt from a tractor trailer dump truck into the
An ironworker was about to screw in sheet metal siding when his arm struck the sissors lift control panel behind him. The whee
An operator was approaching a shallow excavation with a load of fly ash in the bucket of an ingersoll-rand bobcat, m/n 763, s/n
Two employees were working at the base of an unsupported concrete wall while mechanical demolition work was occurring in t
An employee was killed when the automobile he had just stopped was struck in the rear by a pickup truck. The employer was in
Employee #1 (the jobsite Superintendent) was walking east on Highway 150 with an IDOT engineer, looking at the road surface
Employee No.1 was on an elevated job-made scaffold platform, appx. 20 feet high, to perform the final nail hole putting (fillilng
A Tower Technician, was working near the top of a 300 foot communications tower for the purpose of installing a boom. He rele
On 6/22/00, at about 7:30am, employees of J. A. Jones and Barnhart Rigging Co. were preparing to go to work. Some of the em
On 6/22/00, at about 7:30am, employees of J. A. Jones and Barnhart Rigging Co. were preparing to go to work. Some of the em
On 6-22-00, about 7:30am, employees of J. A. Jones and Barnhart Rigging Co. were preparing to go to work. Some of the emp
Two employees, each on a seperate open-sided pontoon boat (measuring 8 foot x 24 foot with a 25 horsepower motor) had fer
A crew of four electricians, 2 journeymen, 1 foreman, and 1 apprentice (D), were in the process of digging a hole to set a new p
on 04/22/96 at approximately 3:45 pm three(3) workers were working on the roof at red hook marine terminal pier 9b in brookly
employee was performing pressure washing of the limestone facade of 10 rockefeller plaza, n.y.c.. while working in a skyjack p
laborer walking on 3 story high welded tubular frame scaffold that was not secured to the building lost balance and fell through
employee died on 4/29/96 from multiple injuries from a fall of approx. 75 feet into the bottom of an empty coal bunker at con ed
workers were attempting to lift a 8 foot x 16 foot x 1 1/4 inch steel street plate with a 15 ton truck crane that had a boom angle,
workers were attempting to lift a 8 foot x 16 foot x 1 1/4 inch steel street plate with a 15 ton truck crane that had a boom angle,
central office technician/clerk, 53 years old, began suffering an asthma attack due to an allergic reaction at approximately 5 p.m
on 8/11/96 (2) employees were installing timber shoring while working at the bottom of a section of trench which was approxima
on 8/11/96 (2) employees were installing timber shoring while working at the bottom of a section of trench which was approxima
employee was working alone next to and above an uncovered skylight on a roof. He was working to recover freon from an air c
iron worker installing q-decking in the interior section of building at a height of 15ft fell off the edge of opening. No fall protection
above mentioned was the sole proprietor of a sub contracting company. On 5/5/97 he went to the worksite to check work progr
on 10/28/94 an employee was installing a 120 volt, single phase dishwasher in a residential apartment. He miswired the machin
worker fell from elevated highway approx 70 feet to a flatbed truck below. The worker was waiting for a load of metal decking to
an employee on a two-point suspended scaffold was attempting to replace a block and tackle while the scaffold was suspended
worker was descending on a 2 point suspension scaffold from the roof level of a 4 story brownstone and lost his balance trying


                                                       Page 134
                                                          all


victim went on board motorized 2 point scaffold after workers complained of it stalling. Victim who was not wearing his safety be
mason was on a two point suspension scaffold doing pointing on brick wall at a height of 9 stories and fell to 4 story roof area. E
mason was on a two point suspension scaffold doing pointing on brick wall at a height of 9 stories and fell to 4 story roof area. E
mason was on a two point suspension scaffold doing pointing on brick wall at a height of 9 stories and fell to 4 story roof area. E
mason was on a two point suspension scaffold doing pointing on brick wall at a height of 9 stories and fell to 4 story roof area. E
the jobsite consists of construction of a 600 foot deep 3rd water tunnel for nyc. The job is done in two phases. The first consists
the jobsite consists of construction of a 600 foot deep 3rd water tunnel for nyc. The job is done in two phases. The first consists
the jobsite consists of construction of a 600 foot deep 3rd water tunnel for nyc. The job is done in two phases. The first consists
employee of 2479 garretson avenue, brooklyn, n.y. 11229, age 37, employed by and owner of pr's contracting died when hit an
victim was using 120vac electric encapsulating spray gun not protected by a ground fault circuit protector when he collapsed. A
employees operating a reimann georger gasoline material hoist to lower debris from 10th floor to 6th floor roof area was propel
deceased was working alone at night in a building that was undergoing a gut rehab. He fell four floors in an empty elevator shaf
iron worker was standing by on temporary work platform being hoisted into position to connect it to bridge tolley rail when the pl
electricians apprentice directed to set up work lights had fallen through sheet rock ceiling.
employee fell from a 43 feet high scaffold to his dead, while installing slates to the building's roof.
employee suffered a cardiac arrest while driving a company car in manhattan on 2/16/97; 2:50 pm. The employee was admitted
A carpenter, was working to dismantle a tubular welded frame scaffold. He had tied an end frame piece to a rope at a well whe
the employees were cutting sections of steel deck to allow access to the bulkheads that were to be replaced. The employees w
the employees were cutting sections of steel deck to allow access to the bulkheads that were to be replaced. The employees w
ironworker employee fell 29 1/2 feet to first floor concrete deck. He was distributing steel q- deck on to the steel framework of th
at a 12 story building undergoing renovation, a visitor to the site fell through a 4 foot wide by 11 foot 6 inch wide floor hole that h
employee collapsed and fell to the floor while cutting metal studs with a metal cutter.
an employee was on an extension ladder leaning against a partly installed piece of vertical steel tubing. The splice plate on the
on 10-20-98 at approx 8:30am, employee franchesco santos and foreman aldo skrobe were doing watermain installation work.
victim was doing manual demolition with a crowbaw under a staircase when the staircase collapsed on top of him killing him.
while working to assist carpenters on a concrete building under construction, the employee attempted to cross the corner of an
employee was in an excavation. He was not noticed when a back hoe operator backfilled the excavation. The employee was as
a laborer at a street construction site was run over by a tractor-semitrailer that was making a right turn into a cross street. At the
at the time and place of occurrence 3 laborers were engaged in manually demolishing a 4-story apartment building that was the
at the time and place of occurrence 3 laborers were engaged in manually demolishing a 4-story apartment building that was the
at the time and place of occurrence 3 laborers were engaged in manually demolishing a 4-story apartment building that was the
employee was trying to untangle a hose that got between the pile and the hammer, when he was coming down the ladder he fe
on 7-13-99 at approximately 1:20pm the victim was hoisting down roofing materials to the street below. When the hoist arm wa
on 7-8-99 at approximately 8:30am, bolting foreman was walking on the edge of the cue decking that was just laid down and wa
employee working alone without fall protection fell 12 floors while in a new elevator shaft. He was on a elevator car frame hung
the foreman of the company (a 33 years old male) was examining bricks at a building in washington heights. He jumped from th
a foreman, who was engaged in demolishing a 2 story brick building, was burning through a steel beam with an acetylene torch
on date/time in item, two laborers on a fifteen foot long two-point suspension scaffold were pressure washing the exterior brick
a restoration mechanic, working to put a two point suspension scaffold on a roof top above a terrace, fell eight stories to his dea
On 3/11/99 at 2:50 pm a elevator mechanic employed by Republic Elevator was struck and killed by a passenger elevator car w
after changing over a hoist sheave on a sling-car, worker was to take car from roof to cellar level to park it for the weekend. Jus
an electrician was moving light fixtures during an office renovation. The employee was standing on a wooden ladder and workin
a crane operator and his two assistants were re-asseblying a crane after it had been secured the day before for a hurricane. Th
while attempting to lift an approximately 12,000 lb concrete hatchway with a crane truck, the boom detached from the truck amp
employee died from broken neck injuries from a fall of 35 feet to lower roof surface. The delro derrick hoist crew was hoisting o
the employee died from fracture injuries from falling approximately 30 feet to the ground from the roof of a 3 story residential fla
victim was involved in pouring and spreading concreate out on the 4th floor deck when the building collapsed to the basement l
While tightening bolts on large sign on top of 50 story building, ironworker fell. He was outside of guardrail and wore no fall prot
the employee, who was doing masonry work, fell from the unguarded platform of a tubular welded frame scaffold which was thr
Elevator mechanic was found at bottom of HVAC duct work. He fell 15 stories. In order to fall down, it would be necessary to cr
On 4/25/00 at approximately 8:16 am, the victim was working on a gut rehab construction site as a supervisor. He was instructe
While bridge painter was disconnecting an air hose from a 150psi line, the safety valve came off. At that point all 150 psi of pre


                                                      Page 135
                                                         all


Four steamfitters were installing an Alfa Laval plate and frame heat exchanger. The employees were attempting to install a met
The employee was working on a 9 feet trench when it collapsed burying the employee from the waist down. The employee died
Deceased employee who had been employed by Falcon Steel, died as a result of neck and head injuries in a fall on an unfinish
Terrazzo floor laborer was measuring the 4th floor elevator lobby floor when he fell 45 feet into the elevator shaft. The shaft ent
Employee 1.1 was engaged in stripping and reglazing a bathtub by himself in a residential apartment. The employee was using
The Backhoe operator was loading a spoil pile into a dump truck as a worker was removing metal from the spoil pile on the opp
On 10/31/00 a rolling scaffold approximately 16 feet high was placed on top of a approximately 15 foot high sidewalk shed so w
Hydraulic platform (used to work on elevated train tracks) collapsed. Nine workers were hospotilized and one died (Ernest Caffi
Employee was on a two point suspension scaffold approx 25 feet high neer the roof when the guardrail gave way. The employe
The victim and 5 other workers were doing roofing work. The victim was replacing coping stones on top of a 12 foot high parap
While using an approximately 25,000 pound hi-lo to lower approximately 5,000 pound pieces of steel to the 2nd floor of a demo
Employee was painting a sidewalk barricade on a 20' extension ladder, opened to approximately 11', off of a mobile scaffold. T
on august 19, 1996 at approximately 10:15 am, an employee was walking on the east side of the road in a southerly direction w
truck driver, also a employee of fredula was dumping a load of gravel on a new driveway, being directed by the victim. Truck bo
employee was working in the basement of the facility installing a new heat exchanger unit. The heat exchanger had just been m
employee was walking on and around the right blind side of a crawler excavator that was moving left to right as it released a 14
employee/owner attempting to off load d5 bulldozer off flatbed/lowboy trailer. D5 went off the side and rolled over, pinning opera
The sole proprietor of hardwood floors by steven labeau was contracted to refinish the floors in a second floor apartment that w
a laborer was operating a walk behind powered roller when he was struck from the side by a bull dozer that was back blading.
on 10-1-98 employee #1 was working on a residential construction site alone when he attempted to remove a plywood floor cov
employee was removing old roofing material from a residential roof and fell 12 feet to the ground.
deceased employee was found inside a cooling chamber of a brazing oven and he was not breathing. The deceased employee
employee was operating a 1989 mack dump truck at a private sand and gravel bed. Train tracks of the norfolk southern railroad
An employee fell 55 feet when he was working on the replacement of the roof membrane on the Syracuse Carrier Dome. It was
Employee #1 was assigned to brush paint to fascia on a two story building. A 32 foot fiberglass extension ladder was used to ga
On October 11, 2000, at approximately 03:30am, while working on the roof of the Chemung County Commerce Center, the em
While inspecting a roof for leaks prior to the start of the repair job, the owner of the company fell through a roof hatch opening t
Employee was working in an unshored, unsloped, unprotected trench that was 5 feet 3 inches deep to 7 feet deep. Water starte
Two Employees were working, installing metal decking. As they were moving a piece of decking back to a storage pile, the piec
Employee climbed to the top of a scaling ladder attached to a metal chimney approximately 200 feet above the ground. Employ
on april 25, 1996 at approximately 08:35 steeplejack employee #1 was ascending steeple - employee #2 was working at ground
roof collapsed
on june 7, 1996, at approximately 8:55 in the morning, employee #1 was up on the walkway along the north side of the bridge o
on july 17, 1996 at 10:25am an employee was fabricating a metal form. One section or "side" (approximately 31' long and rangi
on july 17, 1996 at 10:25am an employee was fabricating a metal form. One section or "side" (approximately 31' long and rangi
three employees engaged in the refurbishment of a shacker conveyor system. The conveyor was approximately 75 feet long an
employees were enaged in night time caisson drilling operations and an employee attending the bentonite slurry hole charging
on friday 10/3/97 at approximately 10:00 o'clock in the morning, a laborer had just gotten a 24-gage metal roof panel in position
employee was run over by dump truck while walking back to the work site.
on 5/28/98 at around 3:00 in the afternoon, a laborer who had been helping to unload i-beams from a flatbed truck left his task
on 8/26/98 at approximately 1:35 pm, employee 1 placed his upper torso into an electrical cabinet that did not have a 480-volt (
victim fell while walking / moving performing steel work.
at approximately 2:15 in the afternoon on 1/14/99, a few minutes after the three-person roofing crew got on the residential roofi
a forty five year old male (employee #1) was working as a flagman for a road paving crew when he was struck by a jack-knifing
employee was run over by a dump truck while backing up to unload paving material.
on 03/12/99 at approximately 9:00am, the foreman tried to move the manually propelled mobile scaffold with two employees on
employee was impacted by a school bus while operating an atv on public roads.
an employee that was doing welding work to the tub grinder machine while standing on the chipper drum, was crushed by the c
the exposed employee was inside an approximate 12 foot deep excavation protected by a trench box. At the bottom of the exca
an employee was electrocuted while attempting to strip a previously de-energized conductor that was not tagged to indicate tha
on 11/02/99 at approximately 10:30am, a crew of three iron workers were installing a flat insulated metal roof on a 40 ft. by 40 f
Employee was standing by a transformer being repaired by the power company when a "flashback" took place. He received bu


                                                     Page 136
                                                           all


Employee was standing by a transformer being repaired by the power company when a "flashback" took place. He received bu
the employer was engaged in laying 10" pipe for the city of tifton. The crew was using a 12 foot long chain to lift the pipes. On th
On 02/04/2000, at approximately 4:30pm, an employee was working from an elevated working platform (personnel platform) ap
An employee was driving her personal vehicle right behind the compactor roller, when suddenly the roller started to move in rev
On 01/11/2001, at approximately 10:00am, an employee working in the law office of Chambers & Rice was exposed to chemica
An employee that was engaged in dismantling a crane boom, was caught under the boom that collapsed right after he removed
On 05/08/2001, at approximately 11:00pm, an employee was setting barrels to close center lane, when a tractor trailer struck h
The construction site Superintendent was killed, when he was struck by lightning while working/walking on a construction site.
On 07/16/2001 at 4:20pm, an employee of Aegis Environmental, Inc., was electrocuted when he made contact with the 120/240
Employee #1 and #2 were working from a six to seven tier mobile scaffold. Employee #2 climbed down to move the mobile sca
Superintendent was struck by fuel truck on road.
a 2-man crew was demolishing a 2-1/2 story house of stone and frame construction, pulling down the structure with a hydraulic
a 3-man crew was attempting to install the jib portion of a 1998 ustc hydraulic crane, model: taxi-king, 28 ton, mounted on a 19
employee was walking in the middle of a two lane roadway under construction. Another employee was operating an off road du
on 8/27/98 at 10:02 employee #1 and another employee were on the flat rubber membrane roof of a 100,100 square foot single
victim was working on a flat roof approximately 6 1/2 - 7 1/2 feet above the pavement when he fell. He first struck his head on
on 2/11/99 at approximately 11:50 am, employee was walking across a 3-lane roadway. Two of the lanes had been closed off f
ronald prible, a sign installer, was working in the aerial bucket of a jlg lift installing a new sign and had elevated the unit to a hei
The victim, a welder was stitch welding in the Baghouse area at an incinerator plant. He was stitch welding on a poppet dampe
The Supervisor for Master Electrical Services, Inc. came in contact with an energized conductor near the base of a parking lot l
employee crushed by a 40 ft. high rebar column collapse of the westbound lane bridge support for the I-895 connector highway
On 4/11/00, an employee of United Sprinkler Co. was attempting to load a calavar corporation condor Model 2532 motorized sc
On May 3, 2000, at approximately 3:30 p.m., employee #1 and the track backhoe operator were in the process of installing a dr
On May 24, 2000, at approximately 4:30 p.m., employee #1 was helping two other employees install metal decking on the 42 ft.
On 7/25/00, at approximately 10:30 employee was working in a dismantling operation of the scaffolding on the 1st floor. The sc
A supervisory employee was installing an overhead fiber-optic communications cable from the basket of a truck-mounted telesc
An employee was installing floor joists to the 2nd level of a new town house. He lost his balance when lifting and adjusting floor
On August 5, 2000, employee #1 was working from a 12 ft. metal straight ladder while measuring eave of porch roof for a gutte
The site is the construction of 767 feet of underground tunnel. When completed it will be a passenger walkback tunnel. The tun
On November 27, 2000, at approximately 9:30 a.m., employee #1 was working in a pipe trench, measuring approximately 60 ft.
On April 18, 2001, at approximately 5:15 p.m., employee #1 was standing on the back of a Ford pickup truck removing the sling
employees were assembling the t-bar or top section of a 1000 foot antenna on the ground. It was noticed that one section of the
employee was grounding a 345 kv power line which had been deenergized. There was a parallel 345 kv power line 80 to 100 fe
employee was on jobsite during non work hours without employers permission, when he was struck by falling beam. Employee
an employee and a sub contractor employee were altering the height of an elevator jack head, in order to meet runby codes. Th
three employees were performing logging operations of a 2+ acre lot for the building of a single family home. An employee was
on 7/3/97 richard strong was nailing down roof deck. He was wearing safety belt attached to a life line. For some unknown reas
employee was scrapping mortor joints and windows at a height of approximately 40' above ground level. He fell off the scaffold
on october 2, 1997 at approximately 11:30 a.m., employee #1 was knelt down in front of 1504 leslie st., baltimore, md 21217 cu
on 10/28/97 at 1:30pm the deceased and employee #1 were standing in man basket while being hoisted by truck crane. Their o
on april 16, 1998 at approximately 11:40 a.m., a painter was working from a 12' wooden straight ladder that was positioned atop
a steel erector working 24' to 28' above concrete floor was not using personal fall protection system when he accidentally stepp
the victims, both masonry workers, were grouting the top of a newly built concrete block wall 12' high x 65' long. They were wor
the victims, both masonry workers, were grouting the top of a newly built concrete block wall 12' high x 65' long. They were wor
on tuesday, july 20, 1999 at approximately 1:00 p.m.,, the foreman, assigned employee #1 to vacuum and clean out (using a du
an employee was opearting a tampo vibratory roller model #rs28 outside of a structural fill area. The area being rolled was appr
two employees of the six m company, inc. were engaged in removing 18' to 20' bridge pilings from the site by rigging them to a
An employee died as a result of a fall from unguarded stairs to concrete steps appro. 18-20 feet below, and then rolled off of an
an employee of dongenal construction company was struck and killed by a motor vehicle driven by a private citizen. The emplo
debris from heavy rain had blocked a culvert under a logging road stopping the flow of water through the culvert. This had caus
a male was killed while loading an agriculture tractor on a trailer. The tractor rolled off the trailer and landed on the deceased.
an employee, employed as a foreman was in charge of equipment traffic in the work area. A scraper loaded with material was p


                                                       Page 137
                                                          all


on september 28, 1998, a 38-year old female died from injuries received from being run over by the steering tires of a blaw kno
employees were shutting down for the day, an operation that involved installing heating blankets inside a gate that controlled in
employees were laying pipe for coalbed methane gas collection pipeline. They were using a procedure called zap-lok to join the
haul truck operator got out of his truck to talk to his coworkers. He noticed his truck starting to roll forward towards another truc
Two employees were electrocuted when a cable on the sideboom unit came in cotact with the overhead power line. The emplo
Two employees were electrocuted when a cable on the sideboom unit came in cotact with the overhead power line. The emplo
On November 6, 2000 at approximately 2:00 pm, employees #1 and #2 were attempting to align the second section of a manho
on june 13, 1996, at about 4:20 am, a construction worker was welding inside the cofferdam around the badger avenue bridge
on july 11, 1996 around 5:30 a.m. no. 1 and two associates (service technician and service manager) arrived at 17400 hawthor
the employer is an electrical contractor working on a new circuit city in long beach. Employee #1 was in the process of relocatin
the division was notified of an accident on 01-07-97 at 10:30 a.m. the accident occurred at pier a in the port of long beach. Ther
on october 25, 1999 at about 0858 hours , an employee of brea electric company was performing an assigned 480 volt 200 am
On August 18, 2000, at about 9:00 AM, No. 1, an employee of a drywall contractor, was electrocuted when he touched a 120 vo
On Tuesday, March 13, 2001, at about 10:30 AM, No. 1, an employee of a roofing contractor, reportedly fell while moving rolls o
f
on november 23, 1996 a crew of two were in the process of installing light poles along the road in a new housing sub-division. U

employee fell 70 feet to ground.
two linemen inside a two man aerial lift basket were engaged in the removal of the top static line at a elevated height of approxi
employee struck
fatality
decedent and co-worker were working on water truck in an effort to repair front steering axle spring. Co-worker was under the t
a ground person hand escorted a (2700 pound, 8 feet x 8 feet x 5 feet) suspended load from the left front side of a transporting
las vegas paving
employee was fatally injured after falling approximately 32 feet from a rebar column.
170
robert dillon framing, inc. - sic: 1751 on july 4, 1998 at approximately 10:15 am, victim was assigned to install 12 trusses with an
a backhoe operator was digging out the utilities trench, when a laborer was crushed by the backhoe bucket.
the employee was walking north on the access road, located on the west side of the lied library job site. As the employee proce
employees were attempting to attach a pre-fabricated efis (exterior finish insulation system) panel to the building structure. The
decedent was assigned to locate fire and smoke dampers that were installed inside the air conditioning ducts. Decedent was on
**************
an employee was run over by a wheel loader.
an employee who was performing flagman duties, stepped out into the northbound lane of highway 95 at mile post 95.5 to stop
a trench excavation was located on the south side of the city of henderson waste reclamation facility final filter building, in hend
on april 28, 1999 an employee working from a six feet baker scaffold fell approximately 12 feet. The employee placed a six feet
the roofing foreman had assigned three employees the task of roofing a small portion of roof, that was located directly above th
an employee engaged in steel erection activities fell off the leading edge deck 24 feet to the concrete slab below.
an employee was clearing out approximately six inches of sand and dirt from underneath the bottom front edge of a precast rei
On 9-26-00 at approximately 1215pm, employee #1 and employee #2 where trying to unclogg a sewer line. Employee #1 went
On 9-26-00 at approximately 1215pm, employee #1 and employee #2 where trying to unclogg a sewer line. Employee #1 went
on february 28, 1998 dosh was called by the fire department hazard materials (hazmat unit) in response to a worker fatality that
on february 28, 1998 dosh was called by the fire department hazard materials (hazmat unit) in response to a worker fatality that
: the employer is involved in the erection of structural steel structures in the construction industry. The process involved in the in
on 02/25/98, supervisor of the deceased, instructed him to remove the plugs from the conduit sleeves in the 1st floor near the e
on 8/26/98, around 2:00 p.m., an electrician died while rewiring a newly installed filler machine at this food packaging plant. At a
on 11/12/98, at approx, 7:12 a.m.the injured no.1, an asphalt laborer, was at jobsite of florence and compton ave in the city of f
reporting entity: on 10/07/99 on or about 14:45, an accident report was filed with this district office regarding an accident which
accident occurred on 07, january, 2000, at approximately 0900 hours, at the warehouse construction site, located at 5822 61st
The accident occurred on July 20, 2000 at about 8 am. the victim (v1), who was grade checking a lot being leveld for new home
On May 25, 2001, a motor grader operator was backing up his vehicle at a northwest angle from the centerline of the Alameda/
On 05/20/01 at or about 08:00 p.m., an accident was filed with this district office by District Attorney(County of Los Angeles). Th


                                                      Page 138
                                                        all


Reporting Entity: On 06/30/01 at or about 13:00 H, an accident report (362507188) was filed with this District Office regarding a
on 03-12-97 about 1400, a 39 year old laborer was critically injured. Employee #1 was completely buried in a 8 foot 10 inch tren
on 10-17-97 about 1700, three employees were attempting to install drain pipe into a five foot excavation next to a planter box i
on 10-17-97 about 1700, three employees were attempting to install drain pipe into a five foot excavation next to a planter box i
employee #1 was working on a 9 ft flat roof patching a leak when he lost his balance and fell backwards off the roof striking the
on 2-9-98 employer was attempting to lift a 52' by 12' framed wooden wall into place on a construction site. Employer was utilizi
hill phoenix excedllence sic: 1711 on 11-19-98 about 1050, a refrigeration mechanic and his foreman were installing refrigeratio
on 03-02-99 about 1040, a 27 year old carpenter was pinned between the forklift basket from which he was working and a stee
the forklift operator, employee #2, was backing an industrial rough terrain forklift. The deceased employee, employee #1, a full
An employee was on site to grade a large residential homes property for shea homes. The job grading foreman was in the proc
On 6-30-00 at approximately 1545 hours, an employee of Sturgeon Electric Company, Inc., 1913 McKinley Avenue, La Verne C
On June 30, 2000, at approximately 1345 hours, a carpenter employed by Bill Tarling construction suffered a fatality when he fe
ON 06-01-00 ABOUT 1400 A 30 YEAR OLD LABORER WAS CRITICALLY INJURED WHEN HE FELL ABOUT 25 FEET FRO
ON 07-31-00 ABOUT 1220 A 44 YEAR OLD GRADE CHECKER WAS CRITICALLY INJURED WHEN A MOTOR GRADER BA
ON 01-08-01 ABOUT 0805 A 41 YEAR OLD ROOFER [EE#1] WAS CRITICALLY INJURED WHEN HE FELL ABOUT 10-12 F
ON 06-16-01 ABOUT 1130 A 34 YEAR OLD CARPENTER WAS CRITICALLY INJURED WHEN HE FELL 10 FEET FROM TH
On July 17, 1997, an employee of a specialty painting contractor was killed while preparing to paint a wine storage tank at the M
on july 19, 1999, employee #1 sustained a fatal crushing injury when he was run over by a 3- axle tractor with an attached dum
On Feb. 19, at 7:15 a.m., an employee was working on an elevated location and fell to the floor below. He was transported to D
On February 10, 2000, at approximately 1400 hours, employee #1 sustained a serious head injury when he was struck in the ba
On December 8, 2000, at approximately 0730, a fatal accident occurred to an employee of a grading company. The accident w
On April 26, 2001, an employee was working at a construction site when he became ill and collapsed. He was transported to La
breckley contracting, inc. po box 5660, ventura, ca 93005 on 12-17-97 at approximately 09:05 hours, employee #1 of breckley c
contra costa electric, inc. 3208 landco drive, bkfd., ca 93308 on 4-29-98, at approximately 10:45 a.m., employee #1 of contra co
during reroofing operations of a light-industrial warehouse, an employee sustained fatal injuries when he fell through an unguar
an employee of smithson fire protection service. Was running a 10'x1" length of copper pipe to be used on the sprinkler system
On May 2 2000 a fifty-two year old iron worker employed by Rod Busters was working on a concrete water tank. The ee was ap
Employee #1 a welder who worked for central coast fabrication Was killed when he walked off a partially completed steel bridge
ROBERT B ENNS CONSTRUCTION; P.O. BOX 162; CAYUCOS, CA. 93430 SIC 1795 On 1-15-01 at approximately 2:15 pm a
Employee an heavy equipment mechanic who worked for Ebenstiener Engineering The employee was working with a crane to
While attempting to hook-up cable on tower structure, the high lift in which they were using became unstable and fell to its side
at the time of the accident this small employer was doing an excavation job for a drain pipe. #1 worked as a laborer for the com
this employer is a small roofing contractor. #1 was a roofer for apr roofing. On july 26, 1997 #1 collapsed while picking up his to
this small employer is doing road re-mediation for the humboldt redwoods state park. Re-mediation means that the employer ta
this small employer sets mobile homes up on the owners property. #1 worked for the employer as a laborer. #1 was sitting on th
curtis sand & gravel 14320 soledad cyn rd canyon country, 91351 sic: 1771 at approximately 0800 on friday 30 may 1997 an e
at approximately 22:30 hrs, 06 june 1997, in response to a telephone call from the district manager, I proceded to 801 s. flowe
r j performance electric co. 12767 foothill blvd.sic: 1731 sylmar, ca 91342 on 7-28-98, at about 10:00 a.m., a serious injury acci
dunkel bros. Machinery moving, inc.p7491, 056-98 1515 e. katella avenuesic: 1796 anaheim, ca 92805 on june 27, 1998, at ab
northwest excavating inc. 18201 napa st., northridge, ca. sic code: 1794. accident victim was standing(outside the orange con
bouchard communications 11231 burbank blvd.sic: 1623 north hollywood, ca 91601 on august 25, 1999, at about 3:30 pm, a s
Accident victim was preparing an opening for an "embed". "Embeds" are used to anchor the iron stairs to the decking. 4x8 inch
SME ConstructionSic Code: 235 Dawson Drive Camarillo, Ca 93011 A backhoe operator was lifting a Reinforced Concrete Pip
Pacific Island Roofing SystemsSic Code: 1761 4031 Brunswick Los Angeles, CA 90039 (323) 816-8843 Accident victim was pu
The injured person was crushed/run over by an operating construction equipment.
on november 17, 1998, at about 12:45 pm, employee #1 was working on the roof of a concrete water-storage tank under const
The deceased was with a crew on the roof of a two-story building installing HVAC units and condensate lines. His duty was ass
On August 3, 2000, at about 12:40 pm, employee #1 was working on an electrical wiring circuit which was energized at 277 vol
The deceased worker was driving a forklift down a road following the truck he had loaded earlier driven by the owner of the com
On 06/30/00 Employee #1 was doing demolition of ventilation system on the roof. He was facing backwards as he stepped on t
The foreman was standing on a plywood sheet at the fifth floor which he placed over two steel duct supports while he and anoth
this fatal accident occurred at a remodelling/renovation construction site. The deceased was employed as an unskilled laborer.


                                                     Page 139
                                                        all


employee was inside a 20 foot trench while another employee was operating a crane, lowering the empty clam shell bucket into
deceased was a master carpenter working on a religious temple building site. A bundle of trusses had been delivered and were
Victim was a construction laborer sent by a temporary employment agency to work for a large general contractor. On the day of
Victim was part of a construction crew building warehouse shelving structures. Operating without fall protection, the employees
Three landscape company employees were attempting to place a 43 foot high palm tree into a holding box that was 42 inches h
Three landscape company employees were attempting to place a 43 foot high palm tree into a holding box that was 42 inches h
on march 26, 1997 at approximately 06:45 a.m., employee #1 fell and received fatal injuries while performing carpenter activitie
on march 26, 1998, at approximately 11:30 p.m., employee #1 was fatally injured when he was struck by a pickup truck driven b
on march 26, 1998, at approximately 11:30 p.m., employee #1 was fatally injured when he was struck by a pickup truck driven b
on december 11,1997,
on december 11,1997,
on march 17, 1998, at approximately 12:25 p.m. employee #1 was operating a billy goat 8.0 h.p. gasoline-powered industrial blo
on december 8, 1998, at approximately 0950 hours, four (4) employees from insul acoustics, inc., south el monte, califor